- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Mapefloor I 910 is used as an adhesion promoter and low-yellowing binder when mixing resin mortar with consistency similar to a mortar screed.
Quick Links - Click To Jump To Section:
Features & Benefits
- Used to mix mortar with a consistency similar to a mortar screed
- Form protective and decorative coatings on resin mortar screeds and to repair old floors
- Complies with the principles defined by EN 13813 “Screed material and floor screeds - Screed material - Properties and requirements”, which specifies the requirements for screed material to be used for installing internal floors
Recommendations & Limitations
- Do not apply Mapefloor I 910 on damp substrates or on substrates with capillary rising damp ( contact Rawlins Technical on 0113 2455450 (option 2) or send a message to [email protected])
- Do not dilute Mapefloor I 910 with solvent or water
- Do not apply Mapefloor I 910 on dusty or crumbling substrates
- Do not apply Mapefloor I 910 on substrates with oil or grease stains or stains in general
- Do not mix partial quantities of the components to avoid mixing errors; the product may not harden correctly
- Do not expose the mixed product to sources of heat
- Even though Mapefloor I 910 is low-yellowing, coatings made from this product may change colour or fade if exposed to sunlight but this has no effect on its performance characteristics
- The colour and finish of the coating may also change if it comes into contact with aggressive chemicals. A change in colour, however, does not mean that it has been damaged by the chemical
- If rooms where the product is being used need to be warmed up, do not use heaters that burn hydrocarbons, otherwise the carbon dioxide and water vapour given off into the air will affect the shine on the finish and ruin its appearance. Use electric heaters only
- Remove aggressive chemicals as soon as possible after they come into contact with Mapefloor I 910
- Use suitable specific cleaning equipment and detergent to clean the product, depending on the type of dirt or stain to be removed
- Protect the product from water for at least 24 hours after application
- Only apply Mapefloor I 910 on substrates that are perfectly dry
- The temperature of the substrate must be at least 3°C higher than the dew-point temperature
Application & Preparation
Please refer to the data sheets in the tab above for further information.
Data sheet
- Manufacturer
- Mapei
- For Use By
- Professional Use
- Interior / Exterior Use
- Interior Use
- For Use On
- Floors
- Application Method
- Trowel
- Pack Size
- 15KG kit (Comp A: 5KG, Comp B: 10KG)
- Coverage
- Refer to data sheet
- Max. Application Temperature
- 35°C
- Min. Application Temperature
- 8°C
- UN Number (Activator)
- UN3082
- UN Number (Base)
- UN2735
- Drying time
- 2-4 hours (dust dry)
- Pot Life
- 20 minutes
- Base Type
- Solvent-Free
- Suitable For Use On
- Floors
- Application Method
- Trowel
- Manufacturer
- Mapei
- Components
- 2K
- Product Usage Type
- Binder
- Product Range
- Mapefloor
- Dry for Light Traffic
- approx. 12 hours
- Hardening
- 7 days
- Colour Family
- Yellow
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Mapei Mapefloor I 910 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT