- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
A waterborne acrylic dispersion based sealant that uses Anker Stuy Tri-cryl technology, is low in odour and contains no harmful solvents.
- Forms an easy to paint, flexible filler with excellent adhesion to bare wood and recommended Anker Stuy coatings systems
- Highly compatible with Hyrdrolux coatings and is UV-resistant
- Due to differences in chemical composition it should not be used over Anker Stuy alkyd emulsion based products from the Ankolux range
- Not designed to be used as an adhesive or glazing sealant and should only be used as a V- joint sealer
Description
Quick Links - Click To Jump To Section:
Substrate and Preparation
Suitable for all commonly used timber species. Timber moisture content should be between 12 and 16%. On Accoya this range should be 4-8%. The substrate must be clean, dry and free from dust, dirt, grease, silicone and wax. Refer to the appropriate Anker Stuy application sheet for other system products such as topcoats and end grain sealers.
Application
Conditions – Ambient temperature and substrate temperature 15 - 30⁰C.
Equipment – Product is dispensed from a hand squeezed bottle. The only tool that may be required is a plastic levelling tool or palette knife.
Procedure – Cut off the tip of the lid and squeeze from the bottle. Cut the lid in the place that is suitable for the width of the joint. Fill the joint area with the material, supplying sufficient pressure to the sides of the joint so that there is immediate adhesion. Avoid applying excess material; level the applied filler with a suitable tool. Apply to primed surfaces such as v-grooves or small break joints and other small gaps to provide moisture protection at joints. Clean off before material dries with a solution of detergent and water.
Usage - Approximately 5 ml/running metre for a 2 x 2 mm fillet.
Drying – 30-60 minutes 2 hours for a 2 x 2mm fillet at 23°C and a relative humidity of 50%. When applying more sealant drying times will be greatly extended. The product is dry once it has turned translucent from the original milky colour.
Drying times are greatly affected by the amount of product applied and can also be greatly reduced if drying conditions are warmer and less humid. Lower temperatures, poor air exchange and high humidity will delay drying. It is important to ensure drying is complete before overcoating. If in any doubt refer to our technical department for details.
Special Information
If coatings are applied too soon before the sealer is dry there will be shrinkage upon drying and the coating film may crack. Follow the drying instructions above diligently to avoid such issues. This product should not be used as a filler for small damages on the face of joinery sections - instead, use Ankolux Woodfiller.
Product Details
10244-977571
Data sheet
- Manufacturer
- Anker Stuy
- For Use By
- Professional Use
- Interior / Exterior Use
- Exterior Use
- For Use On
- Wood
- Application Method
- Spatula
Filling knife - Pack Size
- 900ml
- Max. Application Temperature
- 30⁰C
- Min. Application Temperature
- 15⁰C
- Drying time
- 30-60 minutes 2 hours for a 2 x 2mm fillet at 23°C and a relative humidity of 50%
- Base Type
- Water-Based
- Suitable For Use On
- Wood
- Application Method
- Spatula
- Manufacturer
- Anker Stuy
- Product Range
- Hydrolux
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Anker Stuy Hydrolux V-Joint Sealer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT