- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Mapei Adesilex VZ is a double coat polychloroprenic rubber based adhesive in a solvent solution, particularly suited for the fixing of PVC floor and wall coverings, curved or vertical surfaces where immediate grip is required.
- For professional use
- Bonding of floor and wall coverings in PVC, cork or wood with PVC backing
- PVC mouldings, skirting, corners, nosings etc
- Suitable for use on walls, floors, ceilings, cement render, wood, hardboard, chipboard, fibre cement sheets, gypsum, plasterboard, laminates and plastic materials
- Also for the bonding of PVC sheets to metal and light alloys, PVC or polyurethane foams, together and with wood, metal etc
- Shelf life: 12 months
Quick Links - Click To Jump To Section:
Features & Benefits
- For professional use
- Double coat polychloroprenic rubber based adhesive in a solvent solution, particularly suited for the fixing of PVC floor and wall coverings
- Low viscosity with an immediate bond
- High adhesion and elasticity
- Resistance to temperature and ageing is excellent
- Set to light traffic and ready for use immediately
- Consumption: Mapei trowel No. 1: 0.2-0.3 kg/m²
- Adhesion PEEL 90° in compliance with ISO 22631 (N/mm) - in compliance with ISO 22636:
- PVC
- Non-PVC
- LVT Rubber
- Textiles
- Linoleum
- PO
- PU
Recommendations
- Do not use Adesilex VZ for fixing foam or other materials that are not resistant to the solvents contained in the adhesive (in case of doubt, carry out a preliminary test)
- Install the covering before the solvents contained in Adesilex VZ have completely evaporated
- Do not install on damp substrates or substrates that may be subject to rising damp
- Do not use on old paint
Application Procedure
Preparation of the substrate:
- The substrate must be uniformly dry, flat, and free from cracks, resistant to compression and tension; free from dust and loose particles, varnish, wax, oil, rust, traces of gypsum and products that may prevent bonding
- Moisture content must be as prescribed by the applicable regulations of each individual country
- It is also essential to ensure that there is no rising damp
- Floating screeds over layers of insulation and screeds directly on the ground, must be constructed over a vapour barrier to prevent rising damp
Acclimatisation:
- Before starting the installation, make sure that the floor or wall coverings, the adhesive and the substrate are acclimatised to the recommended temperature
- Floor and wall coverings must be removed from the packaging several hours before installation; the sheets must be freely laid or at least loosened from the rolls to allow acclimatisation and the reduction of tension produced by the packaging
Spreading the adhesive:
- Adesilex VZ is applied evenly with a fine notched trowel (MAPEI No. 1) both to the substrate and to the backing of the covering
- Very absorbent substrates may require a priming coat
Installing the covering:
- Follow the installation instructions given by the floor and wall covering manufacturer
- Lay the covering after the complete evaporation of the solvent, 10-20 minutes at +23°C (do not wait too long): in practice, the correct time is easily determined, wait for the moment when the adhesive is still sticky to the touch without actually sticking to the fingers
- Then proceed to apply the covering, being very careful as errors in laying cannot be corrected due to the immediate bond of the adhesive
- Apply pressure to the bonded surface by means of a suitable metal roller or wooden trowel (or similar)
Cleaning
- Adesilex VZ can be cleaned from tools and clothing whilst fresh, with nitro or benzine solvents
- When dry with specialist solvent cleaner or mechanically
Storage & Safety Instructions
- Under normal conditions and in its original unopened packaging, Adesilex VZ is stable for 12 months
- Read Safety Data Sheet before use (see 'Data Sheets' section above)
Data sheet
- Manufacturer
- Mapei
- For Use By
- Professional Use
- Interior / Exterior Use
- Interior Use
- For Use On
- Walls
Ceilings
Cement Render
Wood
Hardboard
Chipboard
Fibre cement sheets
Gypsum
Plasterboard
Laminates
Plastic - Application Method
- Trowel
- Single, Two or Three Pack
- Single
- Pack Size
- 5Kg
- Max. Application Temperature
- 35°C
- Min. Application Temperature
- 10°C
- Density
- 0.9g/cm³
- Solids by Volume
- 26%
- UN Number
- UN1133
- Waiting time
- 10 - 20 minutes
- Open time
- 12 hours approx
- Suitable For Use On
- Plastic
- Suitable For Use On
- Wood
- Suitable For Use On
- Walls
- Suitable For Use On
- Fibre Cement Board
- Suitable For Use On
- Plasterboard
- Suitable For Use On
- Gypsum
- Suitable For Use On
- Laminate Floors
- Suitable For Use On
- Chipboard
- Suitable For Use On
- Cement Rendering
- Suitable For Use On
- Ceilings
- Suitable For Use On
- Hardboard
- Application Method
- Trowel
- Manufacturer
- Mapei
- Product Usage Type
- Adhesive
- Product Range
- Adesilex
- Dry for Light Traffic
- Immediate
- Colour Family
- Beige
- Viscosity Brookfield (cP)
- 3,500 (rotor 3 - 20 RPM)
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Mapei Adesilex VZ is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT