Quick Links - Click To Jump To Section:

• Features & Benefits
• Pack Contents
• Range of Use
• Characteristic Data
• Certificates
• Possible System Products
• Preparation
• Mixing
• Directions
• Application Examples
• Notes
• Tools / Cleaning
• Storage / Shelf life
• Technical Data

Features & Benefits

• Excellent protection against carbamate formation
• Good hiding power on blinded coatings
• Can be subjected to mechanical and chemical loads
• Coating compatibility test
• Contains no plasticisers, nonylphenols or alkylphenols
• Physiologically harmless once fully cured

Pack Contents

Components A+B.

Range of Use

• Topcoat in the Remmers Deck OS 8 and Deck OS 8 classic systems
• Topcoat in the Remmers Deck OS 11a-II and OS 11b-II systems
• Topcoat in the Remmers Deck OS 14 system in accordance with the maintenance guideline (draft 2016)
• Top sealant for blinded covers
• Coloured coating for roller application

Characteristic Data

On delivery

Once fully cured

• Abrasion according to Taber test
• 47 mg (CS10, 1000 U, 1000 g)

The values stated represent typical characteristic data of the product and are not to be understood as binding product specifications.

Certificates

• Certificate for contact with foodstuffs
• Fire test (classification) Remmers Deck OS 8
• Fire test (classification) Remmers Deck OS 8 classic
• Wear test
• Fire test (classification) Remmers Deck OS 11a - II (epoxy topcoat)
• Fire test (classification) Remmers Deck OS 11b - II
• Instructions for use - Remmers Deck OS 11a - II

Possible System Products

• Epoxy ST 100 (1160)
• Epoxy Primer PF (1224)
• PUR Color ZS (6826)

Preparation

Substrate requirements

The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

It is imperative to use suitable Remmers Epoxy Primers and coating systems.

Remmers Epoxy and Polyurethane Base Coatings fully sprinkled with quartz sand are also suitable as substrates.

For the Remmers Deck OS systems, see the applicable instructions for use.

Mixing

Combi-container

Add the entire quantity of the hardener (component B) to the base compound (component A).

Mix thoroughly with a slow-speed electric mixer (approx. 300 - 400 rpm).

Pour the mixture into a separate container and mix again thoroughly.

Mix for at least 3 minutes.

Insufficient mixing is indicated by streaks forming.

• Mixing ratio (A : B): 82 : 18 parts by weight

As soon as the mixture is ready to use, apply all of it to the prepared surface and spread it using a suitable tool.

Directions

For professional users only!

Conditions for use

Temperature of the material, air and substrate: from min. +10 °C to max. +25 °C.

Once the material has been laid, it should be protected against any direct exposure to water and moisture for at least 24 hours.

Relative humidity should not exceed 80%.

The temperature of the substrate must be at least 3 °C above the dew point temperature during application and curing.

Working time (+20 °C)

Approx. 25 minutes

Drying time (+20 °C)

Foot traffic after 1 day, mechanical loads after 3 days, full loading capacity after 7 days.

At lower temperatures, foot traffic after 2 days (+8 °C).

Setting may be accelerated by adding ACC H. The associated directions for use are available upon request.

As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

Application Examples

Top sealant

Apply the material using a rubber wiper and then roll cross-wise with a suitable epoxy roller.

• Application rate - approx. 0.5-0.8 kg/m² binder (depending on blinding)

Roller coating

Pour the material onto the prepared substrate and then distribute using a suitable tool, e.g. a notched trowel or notched scraper.

Then roll in a crosswise direction using a suitable epoxy roller.

• Application rate approx. 0.35 kg/m²

Notes

• Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C) using standard colours. Slight deviations from these values may arise if the product is worked with on site
• Where necessary, the viscosity can be reduced by adding up to 2% by mass of Remmers V101 Thinner. The use of other thinning agents is not recommended
• Shades of colour with low hiding power (e.g. yellow, red or orange) tend to have a translucent effect on the subsequently applied sealant. In such cases, it is necessary to build up a coordinated colour, e.g. with multiple layers of sealant
• When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur
• If dark or highly pigmented colours are used it is possible that, even with very careful application, shadows or light textures appear on the surface. This is due to the product system and does not in any way affect product suitability
• In case of doubt set up a trial surface
Suitable for vehicle traffic with rubber tyres; not suitable for vehicle loads with metal or polyamide tyres nor for dynamic point loads
• Abrasive mechanical loads leave traces of wear
• Epoxy resins are generally not colourfast when exposed to UV light or weather
• Observe the corresponding test certificate for OS 8 systems
• Observe the instructions for use of the corresponding Remmers Deck OS 11 systems
• Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations

Tools / Cleaning

Rubber wiper, epoxy roller, mixer.

Clean tools, equipment and splashed material immediately while fresh with 101 Thinner.

Take suitable protective and waste disposal measures when cleaning.

Storage / Shelf life

If stored unopened in the original container and kept cool, dry and protected from frost, min. 12 months (component A)/min. 24 months (component B).

Technical Data

* The value in brackets is the smallest permissible value per reading