Quick Links - Click To Jump To Section:

• Features & Benefits
• Pack Contents
• Range of Use
• Characteristic Data
• Possible System Products
• Preparation
• Mixing
• Directions
• Application Examples
• Notes
• Tools / Cleaning
• Storage / Shelf life
• Technical Data

Features & Benefits

• With static crack-bridging ability
• Can be subjected to mechanical loads
• Can be subjected to chemical loads
• Suitable for hand pallet trucks and forklift trucks
• Physiologically harmless once fully cured

Pack Contents

Components A+B.

Range of Use

• Coating
• Filled coating

Characteristic Data

On delivery

Once fully cured

* Epoxy resin mortar 1 : 10 with standard sand

The values stated represent typical characteristic data of the product and are not to be understood as binding product specifications.

Possible System Products

• Epoxy ST 100 (1160)
• M Plus PUR Top M Plus (6735)

Preparation

Substrate Requirements

The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.

The adhesive pull strength of the surface after priming must be at least 1.5 N/mm² on average (smallest single value min. 1.0 N/mm²), compressive strength at least 25 N/mm².

A suitable Remmers epoxy primer or epoxy scratch coat must always be used.

Substrate Preparation

Depending on the substrate, prime with a suitable Remmers epoxy primer and, if needed, level with a - Remmers epoxy scratch coat.

Refer to the current Technical Data Sheet for detailed information on the single products.

Mixing

Combi-container

Add the entire quantity of the hardener (component B) to the base compound (component A).

Mix thoroughly with a slow-speed electric mixer (approx. 300 - 400 rpm).

Pour the mixture into a separate container and mix again thoroughly.

Mix for at least 3 minutes.

Insufficient mixing is indicated by streaks forming.

• Mixing ratio (A : B): 82 : 18 parts by weight

In the case of filled systems, slowly stir the corresponding quantity of filler into the reaction resin mixture and mix thoroughly.

As soon as the mixture is ready to use, apply all of it to the prepared surface and spread it using a suitable tool.

Directions

For professional users only!

Conditions for use

Temperature of the material, air and substrate: from min. +10 °C to max. +30 °C.

After application, protect the surface for at least 48 hours from exposure to water and moisture.

Relative humidity should not exceed 80%.

The temperature of the substrate must be at least 3 °C above the dew point temperature during application and curing.

Working time (+20 °C)

Approx. 30 minutes

Waiting time (+20 °C)

Waiting times between coats should be at least 12 hours and max. 48 hours.

If conditions on site require longer waiting times, the surface must be slightly sanded (until it turns white) before the following application.

Drying time (+20 °C)

Mechanical loads after 3 days, full loading capacity after 7 days.

Setting may be accelerated by adding ACC H. The associated directions for use are available upon request.

As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.

Application Examples

The stated approximate application quantities refer to smooth, level substrates.

The application rates given for each toothed blade are based on experience values and can vary depending on the conditions on site.

The degree of filling is heavily dependent on the climate conditions on the building site and must be corrected upward or downward depending on temperature.

Coating

Pour the material onto the prepared substrate and then distribute using a suitable tool, e.g. a notched trowel or notched scraper.

Subsequently roll over with a looped or a spiked roller.

The application rate depends on the substrate, temperature, required coating thickness, and optical requirements.

Application rate - see table above

Filled Coating

Pour the material filled with Selectmix 01/03 on the previously prepared surface and distribute with a suitable toothed trowel/spreader and, if needed, roll over with a spiked roller.

The degree of filling must be chosen depending on substrate, temperature and required layer thickness.

Application rate - see table above

Notes

Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C) using standard colours. Slight deviations from these values may arise if the product is worked with on site.

From experience, slightly opaque colours (e.g. yellow, red or orange, etc.) have a varnishing effect. Please consider this when choosing and assembling systems.

When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.

Special colours, low layer thickness or differing sand fractions as well as lower temperatures can reduce the maximum degree of filling of the material and possibly affect the visual appearance of the surface.

In case of repairs on the surface or working up to existing surfaces, there will be a visible transition in appearance and texture.

Abrasive mechanical loads leave traces of wear.

Exposure to vehicles with metal or polyamide tyres as well as dynamic concentrated loads can cause faster wearing of the coating.

Epoxy resins are generally not colourfast when exposed to UV light or weather.

Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.

Tools / Cleaning

Toothed trowel, toothed squeegee, smoothing trowel, looped roller, spiked roller, suitable mixing equipment

Clean tools, equipment and splashed material immediately while fresh with 101 Thinner.

Storage / Shelf life

If stored unopened in the original container and kept cool, dry and protected from frost, min. 12 months (component A)/min. 24 months (component B).

Technical Data

* The value in brackets is the smallest permissible value per reading