- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Single pack coating for use in conjunction with Raincoat roof coatings and cladding finishes over PVDF and other plastic coated substrates.
- Adhesion promoting.
- Anti corrosive intermediate coating.
- Based on a specially modified acrylic resin system containing anti-corrosive pigments and inert extenders.
Tor Raincoat APA (RC353) is a single pack coating based on a specially modified acrylic resin system containing anti-corrosive pigments and inert extenders. Tor Raincoat APA is an adhesion promoting and anti corrosive intermediate coating for use in conjunction with Raincoat roof coatings and cladding finishes over PVDF and other plastic coated substrates.
Preparation
Ensure surfaces are sound, clean and dry, free from biological attack etc. before coating and any existing coatings are sufficiently resilient for overcoating. Remove general surface contamination by detergent scrubbing or high pressure power washing. Scrape back any loose or weakly bonded materials, and prepare adjacent sound materials to a firm feathered edge. Clean and abrade exposed metal to a minimum BS7079 standard ST3, removing all visible corrosion and producing a mechanical “key”. Prime all exposed metal as soon as possible. Ensure that the entire area is properly cleaned and surface residues (eg. chalking, plasticiser leachates et) are removed by thorough solvent (Tor Standard Urethane Thinners (TH99)) wiping or vigorous scrubbing with suitable scouring pads and alkaline “cutting” detergents (e.g. diluted Torstrip WDA10) and rinse thoroughly to remove residues. Note: Abrasion of PVDF coatings (other than around loose or corroded areas) with fine abrasives should be avoided as this may polish the surface and impair adhesion of subsequent coatings - white aluminium oxide (80 mesh or coarser) or other hard sharp mineral abrasive paper recommended to ‘cut’ and roughen coatings.
Note: preparation of test patches at survey stage is recommended to verify product compatibility with plastic coated surfaces.
Limitations
- Do not apply if rain is imminent.
- Overcoating should be carried out within the timescale stated to promote maximum intercoat adhesion and avoid film defects. Surfaces must be clean
- This product is not designed for overcoating with other products outside the Raincoat range – verify compatibility by test patch application.
Data sheet
- Manufacturer
- Tor Coatings
- Water / Solvent Based
- Solvent
- For Use On
- PVDF
- Application Method
- Brush, Roller, Airless Spray
- Sheen
- Eggshell
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Single
- Coverage
- 12m² per litre
- Touch Dry
- 2 Hours
- Base Type
- Solvent-Based
- Suitable For Use On
- PVDF
- Finish
- Eggshell
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Spray
- Product Usage Type
- Intermediate Coat
- Product Range
- Tor Roofing & Cladding
- Colour Family
- Grey
- Categorised As
- Cladding Primers
Questions
Question about the product
ben watson on 2022-05-06 05:32:59 | Question:
Hi Do you sell Tor Raincoat in yellow RAL 1023 please |
Answer from Rawlins’ Technical Team:
Unfortunately no, this is only available in grey. But this is normally used as an intermediate coating for use in conjunction with Raincoat roof coatings and cladding finishes over PVDF and other plastic coated substrates. | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
Tor Raincoat APA is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT