Please note that this product CANNOT be used without first receiving a specification from our Technical Department for your project. Please download and complete the 'Thermoguard Wall/Ceiling Enquiry Form' and return by email to [email protected]

If you have any questions regarding this process consult our technical department on 0113 2455450 (option 2).

Thermoguard Wallcoat 30 & 60 Minute System for Plasterboard is a coloured intumescent paint system for interior plasterboard and cement board ceiling and wall surfaces. These packs have been created to help users ensure they are purchasing sufficient product for their project. Each pack contains the correct amount of basecoat (Wallcoat) and topcoat (Thermoguard Wallcoat Smoke & Flame Retardant Topcoat) to ensure protection is achieved in line with the manufacturers recommendations to the respective area in question.

4,000+ colours available from RAL, BS & NCS

Each component of the packs can still be purchased individually if required here: Thermoguard Wallcoat and here: Thermoguard Wallcoat Smoke & Flame Retardant Topcoat

Pack Contents

• 7m² Pack = 1 x 5kg Wallcoat + 1 x 25m² Thermoguard Wallcoat Smoke & Flame Retardant Topcoat
• 14m² Pack = 2 x 5kg Wallcoat + 1 x 25m² Thermoguard Wallcoat Smoke & Flame Retardant Topcoat
• 21m² Pack = 3 x 5kg Wallcoat + 1 x 25m² Thermoguard Wallcoat Smoke & Flame Retardant Topcoat
• 28m² Pack = 1 x 20kg Wallcoat + 1 x 25m² Thermoguard Wallcoat Smoke & Flame Retardant Topcoat

System (Interior Use Only)

To achieve 30 or 60mins + BS EN Class B s1 d0 and Class 0 to sound plasterboard/cement board unpainted or painted with sound, firmly adhering* paints systems;

• Apply 3 coats of Thermoguard Wallcoat @ 4.2m² per kg/per coat

Followed by;

• 1 coat** of Thermoguard Wallcoat Smoke & Flame Retardant Topcoat Matt or Eggshell finish

**2 coats of Thermoguard Wallcoat Smoke & Flame Retardant Topcoat may be required for strong/dark colours - Thermoguard Wallcoat will be provided in a suitable undercoat shade to aid topcoat opacity unless instructed otherwise.

 Hard or smooth paints must be thoroughly abraded to provide a key. Ensure surfaces are dry & free from contamination.

 *Consult Technical Department for advice on adhesion tests on 0113 2455450 (option 2) or send a message to [email protected]

 Fire certificate issued upon completion FREE – apply HERE

Preparation:

All surfaces must be clean and dry. Remove all possible surface contaminates such as grease, smoke residues, silicates etc. Seal water-stain risks with stain blocking sealer suitable to overcoat with water-based acrylic paints. Abrade hard or smooth surfaces with wetted 120 grit wet-or dry abrasive or dust extracting abrader. Rinse off slurry while still damp. When dry, remove any loose or suspect material back to firm edge. Fill and repair any damage to the substrate using a good quality remedial filler.

Application:

Apply Thermoguard Wallcoat and Thermoguard Wallcoat Smoke & Flame Retardant Topcoat at rate stated on specification to protect surfaces & enable project Certification.

Brush & Roller:

Use woven fabric roller sleeves and synthetic bristle brushes.

Spray:

Pressure Pot & Gun conventional unit with small compressor - NOTES:

• Ensure all traces of solvent flushed out
• Thin 5 > 10% with water to spray viscosity
• Adjust fluid flow & air flow as normal for acrylic emulsion paint OR Airless Graco 1500, 3500 or equivalent. 3/8” line, 30 mesh filter on machine, no filter in gun. 521,523, 621 or 623 tip

IMPORTANT - The below information from the manufacturer must be read and referred to your relevant authority for approval BEFORE purchase and use.

PLASTERBOARD

We issue a 30 min Fire Certificate to upgrade 9mm plasterboard and 60 min on 12.5mm plasterboard below voids below 22mm tongue & groove floors or as one side of a partition wall using the specification above, based on the evidence below.

Wallcoat Intumescent Paint added minimum 30 mins Fire Resistance to 12.5mm plasterboard in a 90 min indicative UKAS Fire Test Laboratory.

In all cases 25mm MDF was located 70mm behind the plasterboards in place of floor boards or a board typically the other side of a partition stud wall.

Temperatures were monitored on the protected face (facing away from the furnace) of the MDF, and char damage to the side of MDF facing the plasterboard was measured following the 90 min Fire Test. Char damage was 10 >12 mm, indicating unprotected exposure to fire of 15 > 20 mins during the 90 min period.

Insulation was maintained for 60 mins.

CEMENT BOARD

We issue a 30 min Fire Certificate to upgrade 9mm or 20 min fire rated cementitious board and 60 mins to 12mm 30 min cement-based board under-drawing 22mm+ tongue & groove floor boards or as one side of a fire rated stud partition wall using the specification above, based on the evidence below.

Wallcoat Intumescent Paint added minimum 30 mins Fire Resistance to 10mm and 12.5mm cementitious board and to 12.5 mm plasterboard in a 90 min indicative UKAS Fire Test Laboratory. In all cases 25mm MDF was located 70mm behind the cement boards.

Temperatures were monitored on the protected face (facing away from the furnace) of the MDF, and char damage to the side of MDF facing the cement board was measured following the 90 min Fire Test. Char damage was 10 >12 mm, indicating unprotected exposure to fire of 15 > 20 mins during the 90 min period.

Insulation was maintained for 60 mins.

IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.