- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
A heavy duty, water-based polyurethane resin screed in 6 matt anti-slip colours for highly aggressive environments, with anti-static qualities compliant with BS 2050 for industrial applications.
- High chemical resistance.
- Thermal shock and abrasion resistance.
- Resistant to liquids up to 100°C.
- Decorative.
- Formerly known as Resustat TG69.
Note that all colours have minimum order quantities of 75 units and lead times of 5 working days due to being made to order
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
FasTop TG ESD (formerly known as Resustat TG69) has a unique blend of conductive fillers making it a static-dissipative screed with resin components and pigments that produce a textured matt finish. It is ideal for environments that have a high level of electrical current.
For best results, it should be applied at 6mm nominal thickness. For electrical conductivity leakage resistance, please see the product data sheet at the bottom of this page.
Recommended Uses
- Television studios
- Electronic areas
- Doctor and veterinary surgeries
- Pharmaceuticals
- Engineering
- Chemical plant
Preparation
To achieve the best performance from FasTop TG ESD, the correct surface preparation is essential. Substrates must be clean, sound, dry and free of surface laitance with a minimum strength of 25N/mm sq. All surfaces must be prepared by vacuum blasting or mechanical abrasion.
To ensure maximum bond is achieved, grooves must be cut into the perimeter of the subfloor prior to priming. These should typically be 20mm deep by 8mm wide, and 150mm from, and running parallel with the walls and adjacent to any doorways.
Copper Strips: In order for static-dissipative systems to function effectively, it is essential that the system connects to electrical earth. Where ground floor slabs are laid direct to earth this is often sufficient. Where floors are not directly in contact, or earthing is poor, then copper strips should be laid onto the floor and connected to form a grid and secured to a suitable earthing point. The grid should be applied over the primer but under the Resuprime ESD.
Priming
Resustat TG69 can be applied onto a cured coat of Resuprime ESD two-pack solvent-free epoxy - to be used as a high build single coat static-dissipative primer. Coverage 21 m sq. per 5 kg unit.
Rough or porous surfaces may require an additional coat of Resuprime ST or Resuflor WB, which should be allowed to cure before Resuprime ESD is applied. It is essential the primer coat seals the substrate, so no air pockets or cavities remain.
If substrates have moisture levels above 75% RH, prime the surface with Resuprime MVT prior to Resuprime ESD being installed. (Number of coats dependent on moisture content).
IMPORTANT: Take a check reading of the cured primer before proceeding. See data sheet for details.
Application
The ambient temperatures of the areas should not be allowed to fall below 10°C throughout the application and the curing period. When the primed surface is tack free, FasTop TG ESD should be applied at the required rate as soon after mixing as possible (delay can result in variation in surface finish, colour and add to application problems).
Thoroughly premix the coloured base component ensuring any settled pigment is recovered, then add the hardener component and mix to an even consistency (1 minute). Using a rotary drum mixer or similar forced action mixer bowl, add the aggregate component steadily and then add the conductive component and mix thoroughly for a maximum 2-3 minutes to ensure a lump-free homogeneous compound.
Apply to pre-primed areas and level between battens as necessary with a steel float. Alternatively, a sledge can be used set at the required thickness and finished with a steel float. Where ease of cleaning is very important alongside slip resistance, the final finish can be smoothed by back rolling with a short nap roller. A single pass with the weight of the roller is usually sufficient. FasTop TG ESD screed should ideally be laid in bays to a maximum width of 6m.
Resuthane units should be applied consistently with mixes from the same batch used consecutively where adjacent areas are being laid. NB: Cure times are extended at low temperatures.
Data sheet
- For Use By
- Industrial Use
- Water / Solvent Based
- Water
- For Use On
- Concrete
- Application Method
- Roller
- Sheen
- Smooth-Matt
- Colour
- Standard / Ready Mixed
- VOC Levels
- Ultra-Low (5-49 g/l)
- Single, Two or Three Pack
- Three-Pack
- Pack Size
- 30KG
- Application
- Steel float, Roller.
- Coverage
- 2.5 m. sq. per 30 kg. unit @ 6mm thickness.
- Base Type
- Solvent-Free
- Base Type
- Polyurethane
- Suitable For Use On
- Concrete
- Application Method
- Roller
- Components
- 3K
- Usages
- Anti-Static
- Product Usage Type
- Floor Screed
- Product Range
- FasTop
- Colour Family
- Beige
- Colour Family
- Grey
- Colour Family
- Red
- Colour Family
- Yellow
- Colour Family
- Black
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
RSL FasTop TG ESD is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
RSL Resuflor WB - Standard Readily Available Colours
A multi-purpose, two-pack, water-based epoxy coating in 13 colours primarily for concrete walls and floors. It can also be applied to concrete poured 7 days prior, as well as wood for a dust-free finish. These standard colours are readily available with faster shipping options; more colours are also available separately that are made to...
RSL Resuprime ESD
Designed to be applied prior to the use of Resuflor SL ESD, Resustat SL23, FasTop TG ESD or Resuflor Terrazzo. It is a low viscosity epoxy primer with conductive fillers. Conductive with very low electrical resistance Good adhesion Low odour High solids Easy to apply Formerly known as Resustat CP and Resustat Primer
RSL Resuprime ST Bonding & Priming Coat
2-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and toppings to cementitious and other surfaces. Versatile for many types of application. Excellent adhesive properties. Easy to apply. Can be used as a tack coat for screeds. No unpleasant or harmful odours. Formerly known as Resuprime.
RSL Resuprime MVT
A faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood. Easy application Use on substrates with hygrometer readings <97% Solvent-free...