Follow us on:

Resuflor SL ESD | Formerly Resustat ESM | Anti-Static Epoxy Resin Floor Coating
RSL Resustat ESM

RSL Resuflor SL ESD

RESMB
RSL2953

Static-dissipative flooring system with epoxy resin components, conductive fillers and pigments to produce a decorative finish. It is also crystalline silica free.

  • Hard wearing
  • Hygienic
  • Chemical, abrasion and impact resistance
  • Decorative
  • Easy to apply
  • Formerly known as Resustat ESM
  • Note: This product is made to order (min. order of 35 units) and a lead time of 15 working days
Colour
Pick a Colour
  • Current colour: Black
Close colour picker
  • Black
  • Salsa Red
  • Stirling Grey
  • Flint Grey
Size
Finish
£318.67(incl. VAT)
£265.56(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

The minimum purchase order quantity for the product is 35.

No queries yet, leave the first!
Description

Resuflor SL ESD (formerly known as Resustat ESM) is ideal for industrial and domestic environments that carry high levels of electrical current. It should be installed at 3mm thickness for optimum performance and attractive finish. 

For conductivity leakage resistance, please see the product data sheet at the bottom of the page.

Recommended Uses

  • Television studios
  • Operating theatres
  • Domestic studios
  • Chemical plants
  • Electronic industrial areas
  • Pharmaceuticals

Preparation

New Concrete Floors: New concrete must be clean, sound, dry, and fully cured, surface laitance removed by vacuum enclosed shot blasting or mechanical grinding. A minimum strength of 25N/mm sq. is required.

Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out using Resuscreed PA.

Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with the existing floor coating.

Priming

Open and porous substrates will require priming with Resuprime ST, on dry substrates only with less than 75% ERH reading.

Where the relative humidity of a substrate exceeds 75% ERH, Resuprime MVT should be specified and selected on the basis of hygrometer readings, in accordance with BS 8203.

The number of coats to be applied is chosen in accordance with the following table:

ERH% Required Coating Thickness
75-85 1coat of Resuprime MVT at 200 microns per coat
85-92 2coats of Resuprime MVT at 200 microns per coat
92-97 3coats of Resuprime MVT at 200 microns per coat

Following the application of the Resuprime ST or R.S. Dampshield, copper tape strips are laid to form a grid system where the grids are no larger than 2m x 2m. The copper tape should be left exposed in areas to allow them to be earthed properly. Onto this a coat of Resustat CP is applied to provide a fully conductive layer under the Resuflor SL ESD. It is important to take a conductive reading of the cured Resustat CP before applying the Resuflor SL ESD.

Application

The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally, to allow the ambient and substrate temperature to stabilise prior to installation.

Mixing: Pre-mix the coloured base component to a uniform colour, then mix the entire contents of base with the hardener. If a separate mixing bucket is being used, ensure all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately one to two minutes until the two components have fully combined, then add the aggregate slowly. Mix for a further 1-2 minutes until the aggregate has fully combined and there are no lumps. The mixed unit should be applied immediately.

Resuflor SL ESD should be worked with a trowel or float to achieve an even smooth finish. This is best achieved by the application of smooth, even pressure with the compound poured over the correct coverage rate after fixing the stop ends to control the flow of the material. Finally, roll the area with a spiked roller to achieve an even smooth surface and remove entrapped air. Do not re-roll the area later than 10-15 mins. The surface should be protected from temperatures of less than 10°C and moisture in the early stages of cure. This could adversely affect the flow, levelling and surface finish of Resuflor SL ESD.

Product Details
2953-362904

Data sheet

For Use By
Industrial Use
Interior / Exterior Use
Interior Use
For Use On
Concrete Floors
Application Method
Trowel
Roller
Sheen
Smooth Gloss
Colour
Standard / Ready Mixed
VOC Levels
Low (50-149 g/l)
Single, Two or Three Pack
Three-Pack
Pack Size
30KG
Application
Roller
Coverage
30 Kg will cover 7.5m sq. @ 2mm thickness or 5m sq. @ 3mm thickness.
UN Number (Activator)
UN3066
UN Number (Base)
UN3082
Base Type
Solvent-Free
Base Type
Epoxy
Suitable For Use On
Concrete Floors
Finish
Smooth Gloss
Application Method
Roller
Application Method
Trowel
Components
3K
Usages
Anti-Static
Product Usage Type
Topcoat
Product Range
Resuflor
Colour Family
Grey
Colour Family
Red
Colour Family
Black
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

RSL Resuflor SL ESD is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like
Resuprime ESD | Formerly Resustat CP & Resustat Primer

RSL Resuprime ESD

Designed to be applied prior to the use of Resuflor SL ESD, Resustat SL23, FasTop TG ESD or Resuflor Terrazzo. It is a low viscosity epoxy primer with conductive fillers.  Conductive with very low electrical resistance Good adhesion Low odour High solids Easy to apply Formerly known as Resustat CP and Resustat Primer

Price £73.91 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery
RSL Resuprime ST | Epoxy Resin Priming and Bonding Seal

RSL Resuprime ST Bonding & Priming Coat

2-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and toppings to cementitious and other surfaces.  Versatile for many types of application. Excellent adhesive properties. Easy to apply. Can be used as a tack coat for screeds. No unpleasant or harmful odours. Formerly known as Resuprime.

Price £143.12 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery
RSL Resuflor Patch | Formerly Resuscreed PA & Resupatch

RSL Resuflor Patch

RSL Resuflor Patch (Formerly known as Resuscreed PA and Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments. Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum surface preparation...

Price £51.28 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery