- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Carboline Plasite 4301 HT is a two-component, high performance glass-flake filled coating which is designed for application over steel or concrete in extreme chemical exposures. It is resistant to a wide variety of aggressive chemicals, including organic and inorganic acids, most alkalies, and many solvents.
This product is available as POA. Click here to email us for more information.
- Outstanding resistance to aggressive chemicals
- Suitable for use as a highly chemically resistant lining
- Excellent for splash, spill, and film exposures on structural steel
- Glass-flake reinforced film
- High tensile and flexural strength
- High film thickness
This product is only available as PRICE ON APPLICATION - For more information and to place an order please contact us on 0113 2455450 or email [email protected].
Description
Carboline Plasite 4301 HT is a two-component, high performance glass-flake filled coating was designed for application over steel or concrete in extreme chemical exposures. It is resistant to a wide variety of aggressive chemicals, including organic and inorganic acids, most alkalies, and many solvents.
It is ideally suited for immersion service as internal steel tank linings, as well as for aggressive chemical splash, spill, and fume exposures on structural steel. Typical uses include steel tank and vat linings, secondary containment, structural steel, process floors, grating, sumps and trenches, scrubbers, and clarifiers.
Click To Jump To Section:
- Features and Benefits
- Product Specification
- Drying Times
- Surface Preparation
- Application Methods
- Application Conditions
- Health and Safety
Features and Benefits
- Outstanding resistance to aggressive chemicals
- Suitable for use as a highly chemically resistant lining
- Excellent for splash, spill, and film exposures on structural steel
- Glass-flake reinforced film
- High tensile and flexural strength
- High film thickness
Product Specification
| Technical Data | |
|---|---|
| Carboline Plasite 4301 HT | |
| Theoretical Coverage Rate: |
1.52-1.64 m2/l at 508 microns 1.96-2.31 m2/l at 381 microns |
| Dry Film Thickness: | 381 - 508 microns per coat |
|
For tank linings: Two coats are recommended. For structural steel (other): One or two coats depending on the exposure For concrete: Two coats are recommended |
|
| VOC Values: | As Supplied: 16 g/l |
| Dry Temp. Resistance: | Continuous: 149°C |
| Flash Point: |
Part A: 31 °C Part B: 80 °C |
| Shelf Life: | 2 months |
| Storage Temperature and Humidity: | 10-32 °C |
| For 24-48 hours preceding use, narrow the storage temperature to 21-29°C to facilitate mixing | |
Drying Times
| Curing Schedule | |||
|---|---|---|---|
| Surface Temp | Dry to Recoat | Maximum Recoat | |
| 10°C | 12 Hours | 7 Days | |
| 24°C | 5 Hours | 7 Days | |
| 32°C | 2 Hours | 5 Days | |
- Based on 50% humidity
- Cure for splash and spill service: 24 hours at 23°C and 50% RH
- Cure for immersion service: 48 hours at 23°C and 50% RH
Surface Preparation
General
- Immersion: SSPC-SP10; Minimum 3.5 mil profile
- Non-Immersion: SSPC-SP10; Minimum 2 mil profile
Concrete or CMU
- All concrete requires abrasive blasting to remove laitance and to provide a hard, firm, clean and fully cured concrete surface. All concrete surfaces are required to be filled and sealed prior to application. Contact Rawlins on Tech - 0113 2455450 (option 2) or [email protected] for recommendations
Application Methods
| Product Information | |
|---|---|
| Mixing: |
This product is normally batch mixed and applied with standard airless application equipment but can be applied with plural component catalyst injection spray equipment For batch mixed, standard airless application the part A should be thoroughly mixed until uniform with a mechanical high-speed agitator. Once Part A is uniform the entire contents of part B should be added to the Part A and this catalszed material mixed with a mechanical high speed agitator until uniform and for a minimum of five minutes For plural component catalyst injection consult Rawlins on Tech - 0113 2455450 (option 2) or [email protected] |
| Thinning: |
Thinning is not normally required and not recommended when using plural component catalyst injection spray equipment Additive 47 at up to 5% by volume may be used for thinning when using standard airless application equipment but a reduction in the cure speed can be expected. |
| Pot Life: | 30-40 minutes @ 24°C and significantly less at higher temperatures when batch mixed and applied with standard airless application equipment |
| Spray Application (General): |
Small quantities may be applied using a 2-gallon bottom-fed pot. Conventional atomizing spray system shall be equal to: Binks Model 2001 Gun with 59ASS Fluid Nozzle – 251 Air Cap 559SS Needle Heavy-duty trigger spring recommended. Pot pressure of approximately 50 psi (3.4 bars) Atomizing pressure of approximately 60 psi (4.1 bars). (Use standard production-type pressure pot with air motor drive agitator) Note: Application by conventional spray equipment may affect maximum film building capabilities and coverage rates |
| Airless Spray: |
Airless spray system requires a large capacity pump with a capacity of 3 g.p.m. (11.1 l.p.m.) similar or equal to: Graco (Bulldog may be used in certain instances) King air motor with 0.025” or larger fluid nozzle; 12in (30 cm) minimum spray width is recommended Use liquid pressure of approximately 1800 to 2200 psi (124-152 bars) All screens should be removed from pump and gun. A 3/8 in. (9 mm) diameter fluid line is recommended |
| Plural Component Airless Spray: | Use a 45:1 fluid pump (less filters) on a special cart with a Binks Super Slave, 12 gal Stainless Steel hopper, air regulator assembly, up to a 100’ resin, catalyst and air hose assembly, swivel, Century Gun with T.C.Seat , needle and tip |
| Brush and Roller (General): | Product may be applied using a brush or roller for small areas only |
Application Conditions
| Product Conditions | |||||
|---|---|---|---|---|---|
| Condition | Material | Surface | Ambient | Humidity | |
| Minimum | 16°C | 10°C | 10°C | 0% | |
| Maximum | 32°C | 49°C | 49°C | 80% | |
- Vinyl esters will not cure if exposed to moisture prior to cure. Protect from moisture during application and cure
Health and Safety
Clean Up
- Use Thinner 2 or Acetone
- In case of spillage, absorb and dispose of in accordance with local applicable regulations
Safety
- Read and follow all caution statements on this product data sheet and on the safety data sheets for this product and use personal protective equipment as directed
- Employ normal workmanlike safety precautions
Ventilation
- When used in enclosed areas, thorough air circulation must be used during and after application until the coating is cured
- The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used
- User should test and monitor exposure levels to ensure all personnel are below guidelines
- If not sure or if not able to monitor levels, use MSHA/NIOSH approved supplied air respirator
Caution
- This product is flammable
- Keep away from sparks and open flames
- All electrical equipment and installations should be made and grounded in accordance with all applicable local regulations
- In areas where explosion hazard exist workers should be required to use non-ferrous tools and wear conductive and non-sparking shoes
- Refer to the product data sheet and safety data sheet in the attachments section above for further details
Product Details
3710-477378
Data sheet
- Manufacturer
- Carboline
- For Use On
- Steel, Concrete
- Application Method
- Brush, Roller, Spray
- Colour
- Standard / Ready Mixed
- VOC Levels
- Ultra-Low (5-49 g/l)
- Single, Two or Three Pack
- Two-Pack
- Coverage
- 62-67 ft2/gal at 20.0 mils (1.52-1.64 m2/l at 508 microns) - 80-94 ft2/gal at 15.0 mils (1.96-2.31 m2/l at 381 microns)
- Recommended Thinner/Cleaner
- Carboline Thinner 2
- Max. Application Temperature
- Material: 32°C - Surface: 49°C - Ambient: 49°C - Humidity: 80%
- Min. Application Temperature
- Material: 16°C - Surface: 10°C - Ambient: 10°C - Humidity: 0%
- VOC
- As Supplied: 0.13 lbs/gal (16 g/l)
- Shelf Life (from date of manufacture)
- 2 months
- UN Number (Activator)
- UN3105
- UN Number (Base)
- UN1263
- Dry to Recoat (at 10°C)
- 12 Hours
- Pot Life
- 30-40 minutes @ 24°C
- Suitable For Use On
- Steel
- Suitable For Use On
- Concrete
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Spray
- Product Usage Type
- Tank Lining
- Product Range
- Plasite
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Carboline Plasite 4301 HT is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
You might also like
Carboline Thinner 2
Carboline Thinner 2 is a thinner for use in industrial coatings.
Price
£37.88
(incl. VAT)
In Stock and Available for Delivery
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...
Price
£26.45
(incl. VAT)
In Stock and Available for Delivery