- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Carboline Plasite 4660 provides a two-component, outstanding chemical resistance, abrasion and corrosion protection to a wide variety of steel and concrete substrates in aggressive environments at elevated temperatures.
- Solvent free, 1-layer-system
- Application range includes internal coating for storage tanks for crude oil, hydrocarbons, chemicals and process and pressure vessels of all kinds
- Excellent chemical resistance
- High abrasion resistance
- Approved for use in potable water tanks (at temp. up to 85°C)
- Short curing times - just 24 hours at 20°C, ready for immersion after 7 days
This product is only available as PRICE ON APPLICATION - For more information and to place an order please contact us on 0113 2455450 or email [email protected].
Description
Carboline Plasite 4660 provides a two-component, outstanding chemical resistance, abrasion and corrosion protection to a wide variety of steel and concrete substrates in aggressive environments at elevated temperatures. Its application range includes internal coating for storage tanks for crude oil, hydrocarbons, chemicals and process and pressure vessels of all kinds.
Approved for use in potable water tanks at temp. up to 85°C.
Click To Jump To Section:
- Features and Benefits
- Product Specification
- Drying Times
- Surface Preparation
- Application Methods
- Health and Safety
Features and Benefits
- Solvent free
- Cures in up to 20 hours at 25°C
- Excellent chemical resistance
- High abrasion resistance
- Short curing times
- Approved for use in potable water tanks (at temp. up to 85°C)
- 1-layer-system
Product Specification
| Technical Data | |
|---|---|
| Carboline Plasite 4660 | |
| Volume Solids: | By Volume 100% +/- 2% |
| Theoretical Coverage Rate: |
At 500 µm: 0,82 kg/m² (1.22 m²/kg) <> (2 m²/l) At 1000 µm: 1,64 kg/m² (0.61 m²/kg) <> (1 m²/l) |
| Dry Film Thickness: |
500-1000 µm per coat Number of coats depending on specification |
| Wet Film Thickness: |
500 - 1000 µm per coat Number of coats depending on specification. Maximum sagging limit. 1,0 mm per layer (at 20°C) |
| Chemical Resistance Tables: | Excellent |
| Abrasion Resistance: | <65 mg loss (ASTM D4060) |
| Shelf Life: | 2 years |
| Storage Temperature and Humidity: |
Preferred storage conditions are to keep the containers in a dry and cool area below 35ºC provided with adequate ventilation The containers should be sealed tightly |
Drying Times
| Curing Schedule | ||||
|---|---|---|---|---|
| Surface Temp | Cure Time | Immersion Service | Minimum Recoat Time | Maximum Recoat Time |
| 20°C (68°F) | 24 Hours | 7 Days | 10 Hours | 96 Hours |
| 25°C (77°F) | 20 Hours | 4 Days | 9 Hours | 84 Hours |
| 30°C (86°F) | 18 Hours | 3 Days | 7 Hours | 72 Hours |
| 40°C (104°F) | 12 Hours | 2 Days | 5 Hours | 48 Hours |
Substrate Temperature
- Substrate temperature shall be min. 10°C and min 3°C above the dew point
- Relative humidity shall be below 85%. Temp. and humidity shall be measured close to the substrate
Surface Preparation
General
- Surfaces must be clean and dry
- Employ adequate methods to remove dirt, dust, oil, and all other contaminants that could interfere with adhesion of the coating
Steel
- Blast clean to min. Sa 2½ (ISO 8501-1) with a good profile of 75 – 100 µm roughness
Application Methods
| Product Information | |
|---|---|
| Mixing: |
Part A (base) to be mixed thoroughly with part B (hardener) Mixing time: Part A – premix 4 minutes; then Part A+B – mix 2 minutes; mixer cycles > 100 rpm |
| Thinning: | Thinners shall not be used |
| Ratio: | Part A : Part B = 10 : 1 by weight (6.1 : 1 by volume) |
| Pot Life: |
30 min. v/20° C (material temp.) 25 min. v/25° C (material temp.) 20 min. v/30° C (material temp.) 10 min. v/40° C (material temp.) |
| Density: | 1,64 kg/ltr. mixed |
| Airless Spray: |
Std. > 68:1 ratio or two-comp. equipment Tip size: 0,019-0,026” adjustable Pressure: Min. 400 bar at tip Hose: Max. ¾” diameter and length max. 20 m recommended |
|
Spray Material Temperature Minimum spraying temperature 20°C Filters: All filters to be removed. Material to be sucked without any strainer direct from bucket |
|
| Brush and Roller (General): |
Recommended for small areas, repairs or to precoat edges (stripe-coat) To obtain the required layer thickness, additional coating passes (wet-on-wet) may be necessary |
Health and Safety
Clean Up
- Carboline Thinner 2 or MEK for cleaning the Pump and the Spray equipment
Safety
- Observe the precautionary notices on the container label, and read the material safety data sheet before use
- This product is intended for use by properly qualified professional applicators in industrial conditions
- The product is flammable and should be kept away from sparks, open flames and other sources of ignition
- Smoking is prohibited in the application area
- Wear suitable respiratory equipment and apply in well ventilated areas
- Avoid contact with the skin and eyes
Ventilation
- When used in enclosed areas, thorough air circulation must be used during and after application until the coating is cured
- The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used
Caution
- Fire and explosion hazards: This product contains less than 1% volatile components, however, vapours are heavier than air and can travel long distances, ignite and flash back
- Eliminate all Ignitions sources
- Keep away from sparks and open flames
- All electrical equipment and installations should be made and grounded in accordance with applicable local regulations
- In areas where explosion hazards exist, workers should be required to use non-ferrous tools and wear conductive and non-sparking shoes
- Refer to the product data sheet and safety data sheet in the attachments section above for further details
Product Details
3713-802845
Data sheet
- Manufacturer
- Carboline
- For Use On
- Steel, Concrete
- Application Method
- Brush, Roller, Spray
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 3.79L Kit, 18.39L Kit
- Mixing Ratio
- Part A : Part B 10 : 1 by weight (6.1 : 1 by volume)
- Dry to Recoat (at 20°C)
- Min: 10 Hours, Max: 96 Hours
- Pot Life (at 20°C)
- 30 minutes
- Coverage
- At 500 µm: 0,82 kg/m² (1.22 m²/kg) (2 m²/l), At 1000 µm: 1,64 kg/m² (0.61 m²/kg) (1 m²/l)
- Min. Application Temperature
- 10°C
- Solids by Volume
- 100% +/- 2%
- Shelf Life (from date of manufacture)
- 2 years
- Recommended Dry Film Thickness
- 500-1000 µm per coat
- Recommended Wet Film Thickness
- 500-1000 µm per coat
- UN Number (Activator)
- UN2735
- UN Number (Base)
- UN3082
- Suitable For Use On
- Concrete
- Suitable For Use On
- Steel
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Spray
- Product Usage Type
- Tank Lining
- Product Range
- Plasite
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Carboline Plasite 4660 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
You might also like
Carboline Thinner 2
Carboline Thinner 2 is a thinner for use in industrial coatings.
Price
£37.88
(incl. VAT)
In Stock and Available for Delivery
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...
Price
£26.45
(incl. VAT)
In Stock and Available for Delivery