We are presently renovating a 25year old swimming pool and need to repaint bases of steel supporting columns which are poolside and are in contact with chlorinated water. Can you recommend a suitable paint system. Grit blasting the column bases is not practical and the surface rust will need to removed by hand. Should a rust convertor be part of the paint system. Your advise would be appreciated.

Assuming the steel columns are clean, dry, sound and prepared as detailed in the technical data sheet this primer could be used. Then two coats of Teamac Chlorvar Chlorinated Rubber Paint applied. Preparation of steel by blasting to SA2.5 or mechanical means is required. Teamac Rust Converter could be used.

I'm repainting a grp canal cruiser during November and December out in the open in the UK. Can I use this primer and the anti fouling paint in temperatures down to freezing?

No, the temperature needs to be about 5-10 degrees, you will get moisture entrapment if you try and paint it in those conditions.

Hi, I'm looking for a suitable primer for a small dinghy I am building from plywood. Parts will be bare plywood and parts will be epoxy glassed. The boat will live most of its life indoors, three days in water at a time max. Does the Metaclor level out when brushed on? Also can you recommend a topcoat.

We would instead recommend 2 coats of Teamac P101 High Performance Finish are applied directly to the plywood for this application.

I have a series of metal sumps which will be immersed in water for around 10 weeks only. The sumps have a basic metal primer applied to prevent when dry and exposed to the air. Can you recommend a product to apply over the primer to give a waterproof seal only. The sumps will not be seen and so the finish does not have to be perfect, but they do need to be waterproofed to ensure nor rust develops. I hope you can recommend a product. (Something off the shelf that I can get quickly). Thanks in advance.

Teamac Metaclor Underwater CR Primer followed by 2 coats of Teamac Chlorvar Chlorinated Rubber Paint would be suitable for this application as long as the existing primer is compatible with these products. You can either send our Technical Team the data sheet for the primer used so they can make an assesment or you can carry out a test area with the above products before full application to ascertain compatibility.

Hi, I'm painting shipping container roofs with Chlorinated Rubber Paint, which will be the original paint used on most of them. The roofs are rusty, which will be prepared with wire brush. Would this be suitable primer prior to topcoat of Chlorinated Rubber?

If corrosion protection is the key factor here we would suggest you may be better considering Bradite CR Anti-Corrosive Primer in this instance.

Can I use a rust converter on the steel before priming with Metaclor Underwater Primer?

Yes, Teamac Rust Converter can be applied before application of Teamac Metaclor Underwater CR Primer.

I have a bare steel haul out rail trolley for small boats. made from 100mm x 50mm channell.this will be submerged for each tide and then exposed to air. Please recommend suitable base and topcoat colour is not a critical. 15 Mtrs Linear run of steel. Number of coats to give good protection ? Thank You Supplier in Poole Dorset Area

Our suggestion for this would be to prepare the steel and then apply 2 - 3 good coats of Jotun Jotamastic 87 directly to the surface. A surface tolerant, high build primer, mid coat and finish coat product providing long lasting protection in atmospheric and immersed environments. Can also be applied at sub zero surface temperatures.

I have an old galvanised metal tin bath which i want to put plants and a couple of goldfish in. Will this product seal the bath and will it be fish safe. Thanks

We would recommend thorough cleaning down with Scotch Brite pads to remove all loose and flaking materials, contamination, dirt, grease, etc. and then prime with 1 coat of Teamac 2 Pack Zinc Phosphate Primer followed by 2 coats of Teamac P101 2 Pack Polyurethane Topcoat .

I have an old galvanised metal tin bath which i want to put plants and a couple of goldfish in. Will this product seal the bath and will it be fish safe. Thanks

We would recommend thorough cleaning down with Scotch Brite pads to remove all loose and flaking materials, contamination, dirt, grease, etc. and then prime with 1 coat of Teamac 2 Pack Zinc Phosphate Primer followed by 2 coats of Teamac P101 2 Pack Polyurethane Topcoat .

Teamac Metaclor Antifouling Primer

Reference 520/P149/224

Brand Teamac

Search ID TEA392

In Metallic Grey.
Chlorinated rubber-based primer designed for protective coating.
For wood, metal, and GRP, including marine structures, yachts, narrowboats, and cruisers.
Incorporates Zinc Phosphate for enhanced protection.
Reliable base coat for various antifouling systems.

Colour

Metallic Grey

Size

Finish

£25.54(incl. VAT)

£21.28(ex. VAT)

Quantity

Please choose your colour

In Stock and Available for Delivery (See Delivery Options Below)

ColourPicker Explained

In general we sort colours for products into 2 main groups - ‘Ready Mixed’ and ‘Tinted’.
Tinted colours will always be more expensive than Ready Mixed colours as they need to be produced at the time of order using a tinting machine dispensing colourant into a base*.
During busy periods, this means that tinted colours could take longer, for example – a ready mixed colour ordered on a 3-5 day delivery might arrive within 3 days, however a tinted colour might take the full 5 days to arrive.

To find Ready Mixed colours, search "ready mixed" or select the Ready Mixed 'colour chart'. To see Tinted colours select a colour chart such as RAL, BS, NCS, etc. or search for a colour/hue to see available or related options.

To ensure fair pricing, we split colours into ‘Price Bands’ to group together similar priced colours. If you wish to search for the cheapest tinted colours, always select Price Band 1.

We make every effort to list all available colours, however we also offer a colour match service which can be accessed by contacting our Technical Team on 0113 245 5450 (option 2) or emailing [email protected]

*Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour

Colour reproduction of the Products on the Site is limited by the technology used to deliver web pages and by the colour representation of Customer’s own monitor and computer set-up. We have made every effort to display as accurately as possible the colours of our Products but we cannot guarantee that the colour shown on Customer’s monitor’s display will accurately reflect the colour of the Product on delivery. We recommend that Customer first purchases the smallest Product available or access an industry standard colour chart in person (and not digitally) to ensure that the colour is acceptable for its purposes.

9 questions about the product

Description

Teamac Metaclor Antifouling Primer

Teamac Metaclor Antifouling Primer is a high-performance, single-component primer formulated with chlorinated rubber for optimal durability and adhesion. This versatile primer is specifically designed to provide superior protection against corrosion and fouling on various substrates, including wood, metal, and GRP. Its unique formulation, which includes Zinc Phosphate, offers additional corrosion resistance, making it particularly effective when applied to steel surfaces.

Application & Uses

Metaclor Antifouling Primer is suitable for a wide range of marine and industrial applications. It is ideal for priming narrowboats, cruisers, barges, yachts, and various marine structures. The primer can be used as an underwater base coat on properly prepared steel or as a sealer coat over most conventional paint systems.

Recommended for use on wood, metal, and GRP surfaces.
Best applied over blast-cleaned or mechanically prepared steel to achieve maximum adhesion and longevity.
Can be top-coated with Teamac Antifouling paints or as part of a comprehensive anti-corrosive system.

Application Instructions

For best results, ensure all surfaces are clean, dry, and free from grease, oil, or other contaminants. Blast cleaning to SA 2½ is recommended for steel surfaces; however, mechanical cleaning can be employed if blast cleaning is not possible. Apply to a small test area first to check compatibility, especially over existing coatings.

Mix well before use to ensure an even consistency.
Apply by brush, roller, or airless spray, following recommended drying times between coats.
Always allow a minimum of 8 hours between coats for optimal curing.

Limitations & Precautions

Metaclor Antifouling Primer should not be used on surfaces that have not been properly prepared, as this may affect adhesion and performance. Avoid applying in high humidity or low temperatures, as this can slow drying and curing times. Always follow safety guidelines, including wearing appropriate personal protective equipment (PPE), and ensure adequate ventilation during application.

Do not use on unprepared surfaces.
Avoid application in conditions of high humidity or low temperature.
Not suitable for use in confined spaces without adequate ventilation.

Complementary Products

For enhanced protection and performance, it is recommended to use Metaclor Antifouling Primer in conjunction with the following products:

Teamac Antifouling D: Provides an effective topcoat that works synergistically with the primer to prevent fouling.
Teamac Protector II: Offers additional protection against harsh marine environments, extending the life of the primer and topcoat system.

Health and Safety

Metaclor Antifouling Primer is classified as a hazardous material due to its flammability and potential health effects. It contains substances that may cause skin irritation, serious eye irritation, and respiratory irritation. It is toxic to aquatic life with long-lasting effects. Always handle with care, wear appropriate PPE, and avoid release into the environment.

UN Number: 1263.

Product Details

Reference 9546-962439

Data sheet

Manufacturer: Teamac
For Use By: Consumer Use
Interior / Exterior Use: Exterior Use
Water / Solvent Based: Solvent
For Use On: Steel
Wood
GRP
Metal
Application Method: Airless Spray
Brush
Sheen: Matt
Colour: Standard / Ready Mixed
Single, Two or Three Pack: Single
Pack Size: 1L
2.5L
5L
Dry to Handle (at 20°C): 6 Hours
Dry to Recoat (at 20°C): Minimum 8 hours
Coverage: 6.5-10m² per litre
Recommended Thinner/Cleaner: Teamac Thinner 16
Solids by Volume: 37.5%
VOC: 501 g/litre
Touch Dry: 30 Mins
Size: 1 litre, 2.5 litre, 5 litre and 20 litre
UN Number: UN1263
Base Type: Solvent-Based
Suitable For Use On: Metal
Suitable For Use On: Wood
Suitable For Use On: Steel
Suitable For Use On: GRP
Finish: Matt
Application Method: Brush
Application Method: Spray
Manufacturer: Teamac
Components: 1K
Usages: Marine Applications
Product Usage Type: Primer
Product Range: Metaclor
Fastest Delivery: Next Working Day
Colour Family: Green

Attachments

Download

Product Data Sheet

Download

Safety Data Sheet

Download

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

Name ^*

Email ^*

Question ^*

^* Required fields

I have read and agree to the conditions of use (read)

Andy Knox on 2021-08-19 19:10:34	Question: We are presently renovating a 25year old swimming pool and need to repaint bases of steel supporting columns which are poolside and are in contact with chlorinated water. Can you recommend a suitable paint system. Grit blasting the column bases is not practical and the surface rust will need to removed by hand. Should a rust convertor be part of the paint system. Your advise would be appreciated.
	Answer from Rawlins’ Technical Team: Assuming the steel columns are clean, dry, sound and prepared as detailed in the technical data sheet this primer could be used. Then two coats of Teamac Chlorvar Chlorinated Rubber Paint applied. Preparation of steel by blasting to SA2.5 or mechanical means is required. Teamac Rust Converter could be used.

David Williams on 2019-11-04 21:10:30	Question: I'm repainting a grp canal cruiser during November and December out in the open in the UK. Can I use this primer and the anti fouling paint in temperatures down to freezing?
	Answer from Rawlins’ Technical Team: No, the temperature needs to be about 5-10 degrees, you will get moisture entrapment if you try and paint it in those conditions.

David on 2019-10-09 15:29:10	Question: Hi, I'm looking for a suitable primer for a small dinghy I am building from plywood. Parts will be bare plywood and parts will be epoxy glassed. The boat will live most of its life indoors, three days in water at a time max. Does the Metaclor level out when brushed on? Also can you recommend a topcoat.
	Answer from Rawlins’ Technical Team: We would instead recommend 2 coats of Teamac P101 High Performance Finish are applied directly to the plywood for this application.

William Elliot on 2019-09-16 18:19:56	Question: I have a series of metal sumps which will be immersed in water for around 10 weeks only. The sumps have a basic metal primer applied to prevent when dry and exposed to the air. Can you recommend a product to apply over the primer to give a waterproof seal only. The sumps will not be seen and so the finish does not have to be perfect, but they do need to be waterproofed to ensure nor rust develops. I hope you can recommend a product. (Something off the shelf that I can get quickly). Thanks in advance.
	Answer from Rawlins’ Technical Team: Teamac Metaclor Underwater CR Primer followed by 2 coats of Teamac Chlorvar Chlorinated Rubber Paint would be suitable for this application as long as the existing primer is compatible with these products. You can either send our Technical Team the data sheet for the primer used so they can make an assesment or you can carry out a test area with the above products before full application to ascertain compatibility.

David Howie on 2019-07-23 17:08:35	Question: Hi, I'm painting shipping container roofs with Chlorinated Rubber Paint, which will be the original paint used on most of them. The roofs are rusty, which will be prepared with wire brush. Would this be suitable primer prior to topcoat of Chlorinated Rubber?
	Answer from Rawlins’ Technical Team: If corrosion protection is the key factor here we would suggest you may be better considering Bradite CR Anti-Corrosive Primer in this instance.

Robert Lyall on 2019-05-16 14:16:37	Question: Can I use a rust converter on the steel before priming with Metaclor Underwater Primer?
	Answer from Rawlins’ Technical Team: Yes, Teamac Rust Converter can be applied before application of Teamac Metaclor Underwater CR Primer.

john harwood on 2019-01-23 19:52:19	Question: I have a bare steel haul out rail trolley for small boats. made from 100mm x 50mm channell.this will be submerged for each tide and then exposed to air. Please recommend suitable base and topcoat colour is not a critical. 15 Mtrs Linear run of steel. Number of coats to give good protection ? Thank You Supplier in Poole Dorset Area
	Answer from Rawlins’ Technical Team: Our suggestion for this would be to prepare the steel and then apply 2 - 3 good coats of Jotun Jotamastic 87 directly to the surface. A surface tolerant, high build primer, mid coat and finish coat product providing long lasting protection in atmospheric and immersed environments. Can also be applied at sub zero surface temperatures.

phil hartland on 2017-06-15 09:58:13	Question: I have an old galvanised metal tin bath which i want to put plants and a couple of goldfish in. Will this product seal the bath and will it be fish safe. Thanks
	Answer from Rawlins’ Technical Team: We would recommend thorough cleaning down with Scotch Brite pads to remove all loose and flaking materials, contamination, dirt, grease, etc. and then prime with 1 coat of Teamac 2 Pack Zinc Phosphate Primer followed by 2 coats of Teamac P101 2 Pack Polyurethane Topcoat.

phil hartland on 2017-06-15 09:58:13	Question: I have an old galvanised metal tin bath which i want to put plants and a couple of goldfish in. Will this product seal the bath and will it be fish safe. Thanks
	Answer from Rawlins’ Technical Team: We would recommend thorough cleaning down with Scotch Brite pads to remove all loose and flaking materials, contamination, dirt, grease, etc. and then prime with 1 coat of Teamac 2 Pack Zinc Phosphate Primer followed by 2 coats of Teamac P101 2 Pack Polyurethane Topcoat.

IMPORTANT SHIPPING & DELIVERY INFORMATION

Teamac Metaclor Antifouling Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT

Teamac Thinner 16

Clear liquid thinner. Two-pack, quick-evaporating thinner, ideal for industrial applications. Perfect for spraying on Rapidry, Metaclor, and Anti-corrosive Finish surfaces.

£14.06 (incl. VAT)

Shop now

In Stock and Available for Delivery

General Painting Application Kit

Provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site. Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects, including uPVC surfaces, walls, ceilings, and more. Click to jump down to...

£12.08 (incl. VAT)

Shop now

In Stock and Available for Delivery

Follow us on:

Teamac Metaclor Antifouling Primer

Teamac Metaclor Antifouling Primer

Teamac Metaclor Antifouling Primer

Application & Uses

Application Instructions

Limitations & Precautions

Complementary Products

Health and Safety

Data sheet

Questions

Question about the product

IMPORTANT SHIPPING & DELIVERY INFORMATION

Teamac Thinner 16

General Painting Application Kit