- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
PPG PSX 700 A Clear Coat is a two-component, engineered polysiloxane clearcoat compatible with primed steel, clean metals and concrete, offering high durability in challenging environments.
- Resists dirt pick-up
- Resists graffiti
- High solids, low VOC
- Isocyanate free
PPG PSX 700 A Clear Coat is a two-component, engineered polysiloxane clearcoat compatible with primed steel, clean metals and concrete, offering high durability in challenging environments.
Top Features & Benefits
- Resists dirt pickup, easily cleaned
- Resists graffiti
- High solids, low VOC
- Isocyanate free
- Gloss finish
- No induction time
Product Data
Basic data at 20°C (68°F)
Data for Mixed Product | |
---|---|
Number of components | Two |
Mass density | 1.1 kg/l (9.2 lb/US gal) |
Volume solids | 78 ± 2% |
VOC (supplied) | Directive 1999/13/EC, SED: max. 200.0 g/kg max. 222.0 g/l (approx. 1.9 lb/gal) (aluminum) |
Recommended dry film thickness | 20 - 25 µm (0.8 - 1.0 mils) per coat |
Theoretical spreading rate | 39.0 m²/l for 20 µm (1564 ft²/US gal for 0.8 mils). 31.2 m²/l for 25 µm (1251 ft²/US gal for 1.0 mils) |
Dry to handle | 5 hours |
Overcoating interval | 4 hours. Maximum: 30 days |
Full cure after | 7 days |
Shelf life | Base: at least 12 months when stored cool and dry. Hardener: at least 12 months when stored cool and dry. |
Notes:
See Additional Data: Overcoating intervals and Curing time.
Recommended Substrate Conditions and Temperatures
Substrate Condition
- Existing sound coating systems; sufficiently roughened, dry and cleaned
- Surface must be dry and free from any contamination
Concrete
- Dried for at least 28 days in good ventilation conditions
- Moisture content should not exceed 4.5%
- Concrete must be sound, dry, free from laitance and any contamination
- Rough surface; eventually abraded by power tool or diamond abrading tool
Non-ferrous Metals and Stainless Steel
- Surface must be free from grease, salts and any contamination
- Surface should be sufficiently roughened (e.g. sandpapering, sweep blasting)
Substrate Temperature and Application Conditions
- Surface temperature during application should be between 5°C (41°F) and 50°C (122°F)
- Substrate temperature during application and curing should be at least 3°C (5°F) above dew point
- Ambient temperature during application and curing should be between 5°C (41°F) and 50°C (122°F)
- Relative humidity during application and curing should be between 50% and 85%
Instructions for Use
- One or two coats of 20 - 25 µm (0.8 - 1.0 mils)
- Mixing ratio by volume: base to hardener 83:17 (5:1)
- The temperature of the mixed base and hardener should be above 10°C (50°F), otherwise extra thinner may be required to obtain application viscosity
- The paint should be stirred well before use, preferably by means of a mechanical mixer, to ensure homogeneity
- Add hardener to base and continue stirring until homogeneous
- If required, thinner should be added after mixing the components
- Adding too much thinner results in reduced sag resistance and slower cure
Air spray
Recommended thinner: THINNER 60-12
Volume of thinner: 0 - 10%, depending on required thickness and application conditions
Nozzle orifice: 1.0 - 1.5 mm (approx. 0.040 - 0.060 in)
Nozzle pressure: 0.3 - 0.4 MPa (approx. 3 - 4 bar; 44 - 58 p.s.i.)
Airless spray
Recommended thinner: THINNER 60-12
Volume of thinner: 0 - 10%, depending on required thickness and application conditions
Nozzle orifice: Approx. 0.38 – 0.43 mm (0.015 – 0.017 in)
Nozzle pressure: 15.0 - 18.0 MPa (approx. 150 - 180 bar; 2176 - 2611 p.s.i.)
Brush/roller
Recommended thinner: THINNER 60-12
Volume of thinner: 0 – 5%
Cleaning solvent
Overcoating interval for DFT up to 25 µm (1.0 mils) | |||||
---|---|---|---|---|---|
Overcoating with... | Interval | 5°C (41°F) | 10°C (50°F) | 20°C (68°F) | 30°C (86°F) |
Itself | Minimum Maximum |
12 hours 30 days |
8 hours 30 days |
4 hours 30 days |
2 hours 30 days |
Curing time for DFT up to 25 µm (1.0 mils) | ||
---|---|---|
Substrate Temp. | Dry to Handle | Full Cure |
5°C (41°F) | 16 hours | 16 days |
10°C (50°F) | 9 hours | 10 days |
20°C (68°F) | 5 hours | 7 days |
30°C (86°F) | 3 hours | 5 days |
Pot life
10°C (50°F) = 6 hours
20°C (68°F) = 4 hours
30°C (86°F) = 3 hours
40°C (104°F) = 2 hours
Safety Precautions
- This is a solvent-borne paint and care should be taken to avoid inhalation of spray mist or vapor, as well as contact between the wet paint and exposed skin or eyes.
- Since improper use and handling can be hazardous to health and cause of fire or explosion, safety precautions included with Product Data/Application Instruction and Material Safety Data Sheet must be observed during all storage, handling, use and drying periods.
Worldwide Availability
It is always the aim of PPG Protective and Marine Coatings to supply the same product on a worldwide basis. However, slight modification of the product is sometimes necessary to comply with local or national rules/circumstances. Under these circumstances an alternative product data sheet is used.
Data sheet
- Manufacturer
- PPG
- Water / Solvent Based
- Solvent
- For Use On
- Steel, Metal, Concrete
- Application Method
- Brush, Roller, Spray
- Sheen
- Gloss
- Colour
- Clear
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 4.5L
- Parts
- Two
- Base Type
- Solvent Based
- Solvent
- Polysiloxane
- Mixing Ratio
- 5:1
- Suitable Substrates
- Primed steel, clean metals, concrete
- Key Features
- Resists dirt pickup, easily cleaned, resists graffiti, high solids, low VOC
- Application
- Brush, Roller, Spray
- Touch Dry (at 20°C)
- -
- Dry to Handle (at 20°C)
- 5 hours
- Dry to Recoat (at 20°C)
- 4 hours
- Fully Cured (at 20°C)
- 7 days
- Pot Life (at 20°C)
- 4 hours
- Coverage
- 7.2 m²/l for 125 µm (289 ft²/US gal for 5.0 mils)
- Recommended Thinner/Cleaner
- PPG Thinner 60-12, PPG Thinner 90-58
- Unit Contents
- -
- Compatible Primers
- -
- Compatible Topcoats
- Itself
- Max. Application Temperature
- 50°C (122°F)
- Min. Application Temperature
- 5°C (41°F)
- Density
- 1.4 kg/l (11.3 lb/US gal)
- Solids by Volume
- 90 ± 2%
- Heat Resistance (up-to)
- 120°C (250°F)
- VOC
- Directive 1999/13/EC, SED: max. 200.0 g/kg max. 222.0 g/l (approx. 1.9 lb/gal) (aluminum)
- Shelf Life (Once Opened)
- Base: at least 36 months when stored cool and dry. Hardener: at least 24 months when stored cool and dry
- UN Number (Activator)
- UN3470
- UN Number (Base)
- UN3082
- Base Type
- Solvent
- Suitable For Use On
- Metal
- Suitable For Use On
- Concrete
- Suitable For Use On
- Steel
- Finish
- Gloss
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Spray
- Product Usage Type
- Topcoat
- Product Range
- PSX
- Colour Family
- Clear
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
PPG PSX 700 A Clear Coat is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
PPG Thinner 60-12
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products. More Information Delivery Info
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...