Follow us on:

PPG SteelGuard 751
PPG SteelGuard 751

PPG SteelGuard 751

358544
PPG3927

PPG SteelGuard 751 is a one-component thin-film solvent-borne intumescent coating for fire protection of structural steelwork. Provides up to 120 minutes protection from cellulosic fires.

  • Tested and assessed to EN 13381-8, BS 476-20/21 and AS 1530.4
  • CE marked product, ETA 15/0439
  • Assessed to ETAG 018-2 for all durability classifications
Colour
Size
Finish
£367.12(incl. VAT)
£305.93(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

PPG SteelGuard 751 is a one-component thin-film solvent-borne intumescent coating for fire protection of structural steelwork. Provides up to 120 minutes protection from cellulosic fires.



Top Features & Benefits


  • Off-site or on-site application
  • Up to 1500 µm (60.0 mils) DFT in a single coat
  • Suitable for C1 to C4 internal and external environments (ISO 12944); for dry internal (C1) environments no topcoat is required
  • Weather resistant up to 12 months without topcoat provided the coating has been applied in accordance with INFORMATION SHEET 1222 and is not subject to running or pooling water, high humidity or immersion conditions
  • Tested and assessed to EN 13381-8, BS 476-20/21 and AS 1530.4
  • CE marked product, ETA 15/0439
  • Assessed to ETAG 018-2 for all durability classifications



Product Data


Recommended Substrate Conditions and Temperatures

  • Approved primer must be sound, dry and free from any contamination
  • Substrate temperature and application conditions
  • Substrate temperature during application and curing should be between 5°C (41°F) and 40°C (104°F)
  • Substrate temperature during application and curing should be at least 3°C (5°F) above dew point
  • Ambient temperature during application and curing should be between 5°C (41°F) and 40°C (104°F)
  • Relative humidity during application and curing should not exceed 85%

 

Instructions for Use

  • Stir thoroughly until homogeneous and free of lumps
  • Adding too much thinner results in reduced sag resistance and slower cure

 

Airless Spray

Recommended thinner: PPG THNINER 21-06 (normally no thinner required)

Volume of thinner: 0 - 5%

Nozzle angle: 20° – 50°, depending on shape of steel parts

Nozzle orifice: Approx. 0.48 – 0.64 mm (0.019 – 0.025 in)

Nozzle pressure: 20.0 MPa (approx. 200 bar; 2901 p.s.i.)

 

Notes
All filters, including surge bottle and gun filters to be removed. External fluid uptake pipe filter is recommended.

 

Brush/Roller

For small areas only (touch up and repair). No thinner should be added.

 

Cleaning Solvent

PPG THINNER 21-06



Data for Product
Number of components One
Mass density 1.35 kg/l (11.27 lb/US gal)
Volume solids 75 ± 3%
VOC (Supplied) Directive 1999/13/EC, SED: max. 257.0 g/kg UK PG 6/23(92) Appendix 3: max. 330.0 g/l (approx. 2.8 lb/US gal) EUR Directive: 2004/42/IIA(i)(500) 370 g/l)
Reccomended film thickness 200 - 1500 µm (8.0 - 60.0 mils) per coat
Theoretical spreading rate 1.07 m²/l for 700 µm (43 ft²/US gal for 28.0 mils)
Dry to touch 30 minutes
Overcoating interval Minimum: 6 hours
Maximum: Unlimited
Shelf life At least 18 months when stored cool and dry



Spreading rate and film thickness
DFT Theoretical spreading rate
200 µm (8.0 mils) 3.75 m²/l (150 ft²/US gal)
400 µm (16.0 mils) 1.88 m²/l (75 ft²/US gal)
700 µm (28.0 mils) 1.07 m²/l (43 ft²/US gal)
1000 µm (40.0 mils) 0.75 m²/l (30 ft²/US gal)
1500 µm (60.0 mils) 0.50 m²/l (20 ft²/US gal)

Note: Maximum DFT when brushing: 300 µm (12.0 mils)



Overcoating interval for DFT up to 700 µm (28 mils)
Overcoating with... Interval 5°C (41°F) 10°C (50°F) 15°C (59°F) 20°C (68°F) 30°C (86°F)
Itself Minimum
Maximum
12 hours
Unlimited
10 hours
Unlimited
8 hours
Unlimited
6 hours
Unlimited
4 hours
Unlimited



Overcoating interval for DFT up to 1000 µm (40 mils)
Overcoating with... Interval 5°C (41°F) 10°C (50°F) 15°C (59°F) 20°C (68°F) 30°C (86°F)
Steelguard 2458 Minimum
Maximum
4 hours
Unlimited
2 hours
Unlimited
1.5 hours
Unlimited
1 hour
Unlimited
45 minutes
Unlimited
Other approved coats Minimum
Maximum
5 days
Unlimited
3 days
Unlimited
60 hours
Unlimited
48 hours
Unlimited
36 hours
Unlimited



Curing time for DFT up to 700 µm (28 mils)
Substrate Temp. Dry to Touch
5°C (41°F) 2 hours
10°C (50°F) 1.5 hours
15°C (59°F) 1 hour
20°C (68°F) 30 minutes
30°C (86°F) 20 minutes

Note: Drying times may vary considerably depending on ambient conditions, A/V m⁻¹ (Hp/A) of section and applied film thickness



IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.



Product Details
3927-494891

Data sheet

Manufacturer
PPG
Interior / Exterior Use
Interior & Exterior
Parts
One
Base Type
Solvent-borne
Solvent
Solvent-based
Mixing Ratio
-
Suitable Substrates
Structural steel
Key Features
Tested and assessed to EN 13381-8, BS 476-20/21 and AS 1530.4, CE marked product, ETA 15/0439, assessed to ETAG 018-2 for all durability classifications
Application
Spray
Touch Dry (at 20°C)
30 minutes
Dry to Handle (at 20°C)
-
Dry to Recoat (at 20°C)
6 hours
Fully Cured (at 20°C)
-
Pot Life (at 20°C)
-
Coverage
1.07 m²/l for 700 µm (43 ft²/US gal for 28.0 mils)
Recommended Thinner/Cleaner
PPG Thinner 21-06
Unit Contents
-
Compatible Primers
-
Compatible Topcoats
Itself, PPG SteelGuard 2458
Max. Application Temperature
40°C (104°F)
Min. Application Temperature
5°C (41°F)
Density
1.35 kg/l (11.27 lb/US gal)
Solids by Volume
75 ± 3%
Heat Resistance (up-to)
-
VOC
Directive 1999/13/EC, SED: max. 257.0 g/kg UK PG 6/23(92) Appendix 3: max. 330.0 g/l (approx. 2.8 lb/US gal) EUR Directive: 2004/42/IIA(i)(500) 370 g/l)
Shelf Life (Once Opened)
At least 18 months when stored cool and dry
UN Number
UN1263
Base Type
Solvent-Based
Suitable For Use On
Steel
Finish
Matt
Application Method
Spray
Product Usage Type
Basecoat
Product Range
Steelguard
Colour Family
White
Fire Rating
120 Minutes
Site Application
On-Site
Site Application
Off-Site
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

PPG SteelGuard 751 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like
PPG Thinner 21-06 | Paint Thinner

PPG Thinner 21-06

This thinner has been developed by PPG Protective and Marine Coatings for use with selected paint products.

Price £42.59 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery
Hand & Power Tool Surface Preparation Kits for Steel

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £25.93 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery