Follow us on:

HMG Z4381 Single Pack Acrylic Lacquer

HMG Z4381 Single Pack Acrylic Lacquer

6511000
HMG4354

HMG Z4381 Single Pack Acrylic Lacquer is an air drying clearcoat which is supplied ready for use.  It is ideally suited for use where localised and spot repair work is necessary.

Colour
Size
Finish
£22.10(incl. VAT)
£18.42(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

HMG Z4381 Single Pack Acrylic Lacquer is an air drying clearcoat which is supplied ready for use.  It is ideally suited for use where localised and spot repair work is necessary.

It is not advisable to do overall resprays with this material.



Click To Jump To Section:




Features & Benefits


  • Quick drying - touch dry in 5 minutes
  • Ease of use
  • Available in clear



Product Specification


Technical Data
Volume Solids: 18.3%
VOC Content: 0.755Kg/L
SG: N/A
Viscosity: 25 s (ISO 3 mm) - Kintetic (Spray Gun)
Density: 0.904 g/cm³
Storage Conditions: Store between 5°C - 25°C. When not in use, cans must be kept sealed.
Shelf Life: 12 months from delivery date in original sealed containers.
Flash Point: - 6°C



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness
Aerosol: N/A N/A
Compliant Spray Gun: N/A N/A



Coverage: 6.0 square metres per litre @ 25 microns dft (Theoretical).

  • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
  • These values are a guide only and are not to be used as specifications.
  • Film thickness will vary depending on actual use and specification.
  • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



Drying Times


Drying Times At 20°C/RH 50%
Touch Dry: 5 minutes
Fully Cured: 60 minutes



Surface Preparation


  • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
  • Always use the same batch number on the same job.
  • Check colour & sheen.
  • Filter the product immediately before use.
  • Reduce emissions and maintain quality by replacing tin lid after use.



Application Methods


Technical Data
Aerosol Compliant Spray Gun
Mixing Ratio: Ready for use Ready for use
Thinner Options: N/A N/A
Viscosity: N/A 20 secs B4 Cup
Spray Gun Setup: N/A N/A
Number Of Coats (Guide Only): 3 - 4 coats 3 - 4 coats
Flash Off: 5 minutes between coats. 5 minutes between coats.





Product Notes


Information on basic physical and chemical properties
Form: Liquid
Colour: According to product specification.
Odour: Characteristic
Odour Threshold: Not determined
pH-value: Not determined
Change in Condition
Melting point/freezing point: Undetermined
Initial boiling point and boiling range: 80°C
Flash Point: - 6°C
Flammability (solid, gas): Not applicable
Ignition temperature: 315°C
Decomposition temperature: Not determined.
Auto-ignition temperature: Product is not selfigniting
Explosive properties: "Product is not explosive. However, formation of explosive air vapour mixtures are possible."
Explosion limits: Lower: 1.2 Vol %
Explosion limits: Upper: 11.5 Vol %
Vapour pressure at 20°C: 105 hPa
Density at 20°C: 0.904 g/cm³
Relative density: Not determined
Vapour density: Not determined
Evaporation rate: Not determined
Solubility in / Miscibility with water: NOT MISCIBLE
Partition coefficient: n-octanol/water: Not determined
Viscosity: Dynamic at 20°C: 200 mPas
Viscosity: Kinematic: 25 s (ISO 3 mm)
Solvent content: Organic solvents: 74.7%
Solids content: 18.3%



Health & Safety


  • Refer to the safety data sheet in the attachments section above and tin label prior to use.
  • Suitable respiratory equipment should be worn when spraying.

Click to go back to the top of the page

Product Details
4354-601959

Data sheet

Manufacturer
HMG Paints Limited
Water / Solvent Based
Solvent
Application Method
Spray
Single, Two or Three Pack
Single
Parts
One part pack
Base Type
Acrylic
Key Features
Quick drying - Touch Dry in 5 minutes. Ease of use.
Application
Spray
Touch Dry (at 20°C)
5 Mins
Fully Cured (at 20°C)
60 Mins
Coverage
6.0 square metres per litre @ 25 microns dft (Theoretical)
Density
0.904 g/cm³
Solids by Volume
18.3 %
VOC
0.755Kg/L
Shelf Life (from date of manufacture)
12 months from delivery date in original sealed containers
Finish
Gloss
Size
1L and 5L
UN Number
UN1263
Base Type
Acrylic
Finish
Gloss
Application Method
Spray
Product Usage Type
Repair
Colour Family
Clear
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

HMG Z4381 Single Pack Acrylic Lacquer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT



COVERAGE CALCULATOR
Units
Film Thickness
Total area²
Or enter length and width dimensions:
Length
Width

*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage

You might also like
Hand & Power Tool Surface Preparation Kits for Steel

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £25.93 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery