Follow us on:

HMG A1240 High Opacity White

HMG A1240 High Opacity White

TOPA1240
HMG4366

HMG A1240 High Opacity White is a high quality brushing enamel that gives excellent obliteration of previous coatings without the loss of gloss level, adhesion or durability.

  • Availiable in white
  • For use with synthetic high opacity undercoats
Colour
Size
Finish
£122.80(incl. VAT)
£102.33(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

HMG A1240 High Opacity White is a high quality brushing enamel that gives excellent obliteration of previous coatings without the loss of gloss level, adhesion or durability.



Click To Jump To Section:




Features & Benefits


  • Availiable in white
  • For use with synthetic high opacity undercoats



Product Specification


Technical Data
Volume Solids: 70.9%
VOC Content: 0.32kgs/ltr
SG: -
Viscosity: 430 mPas
Density: 1.28 g/cm³
Storage Conditions: Store between 5°C - 25°C. When not in use, cans must be kept sealed.
Shelf Life: 12 months from delivery date in original sealed containers.
Flash Point: 31°C



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness
Brush: 35 µm 100 µm



Coverage: 6 - 8 square metres per litre @ 55 microns dft.

  • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
  • These values are a guide only and are not to be used as specifications.
  • Film thickness will vary depending on actual use and specification.
  • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



Drying Times


Drying Times At 20°C
Touch Dry: 3 hours
Dry To Recoat: Minimum 16 hours @20°C
Fully Cured: 24 hours



Surface Preparation


  • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.



Application Methods


Technical Data
Brush
Mixing Ratio: Ready for use
-
Thinner Options: n/a
-
Viscosity: -
Number Of Coats (Guide Only): 2 full coats
Flash Off: -



Product Notes


Information on basic physical and chemical properties
Form: Liquid
Colour: White
Odour: Characteristic
Odour Threshold: Not determined
pH-value: Not determined
Change in Condition
Melting point/freezing point: Undetermined
Initial boiling point and boiling range: 135°C
Flash Point: 31°C
Flammability (solid, gas): Not applicable
Ignition temperature: 200°C
Decomposition temperature: Not determined.
Auto-ignition temperature: Product is not selfigniting
Explosive properties: "Product is not explosive. However, formation of explosive air vapour mixtures are possible."
Explosion limits: Lower: 0.6 Vol %
Explosion limits: Upper: 7.0 Vol %
Vapour pressure at 20°C: 1 hPa
Density at 20°C: 1.28 g/cm³
Relative density: Not determined
Vapour density: Not determined
Evaporation rate: Not determined
Solubility in / Miscibility with water: NOT MISCIBLE
Partition coefficient: n-octanol/water: Not determined
Viscosity: Dynamic at 20°C: 430 mPas
Viscosity: Kinematic: Not determined
Solvent content: Organic solvents: 3.0%
Solids content: 70.9%



Health & Safety


  • Refer to the safety data sheet in the attachments section above and tin label prior to use.

Click to go back to the top of the page

Product Details
4366-605545

Data sheet

Manufacturer
HMG Paints Limited
Water / Solvent Based
Solvent
For Use On
Metal
Application Method
Brush
Sheen
Matt, satin, gloss
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Pack Size
2.25L, 5L
Mixing Ratio
RFU
Touch Dry (at 20°C)
3 Hours
Dry to Recoat (at 20°C)
Minimum 16hrs @20°C
Fully Cured (at 20°C)
24 Hours
Coverage
6-8 square metres per litre @ 55 microns dft
Coverage
6 - 8 square metres per litre @ 55 microns dft
Density
1.28 g/cm³
Solids by Volume
70.9 %
Heat Resistance (up-to)
80°C
VOC
0.32kgs/ltr
Shelf Life (from date of manufacture)
12 months from delivery date in original sealed containers
Size
5L
Recommended Dry Film Thickness
35 µm
Recommended Wet Film Thickness
100 µm
UN Number
UN1263
Base Type
Solvent-Based
Suitable For Use On
Metal
Finish
Matt
Finish
Satin
Finish
Gloss
Application Method
Brush
Colour Family
White
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

HMG A1240 High Opacity White is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like
Hand & Power Tool Surface Preparation Kits for Steel

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £25.93 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery