- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
HMG Tyre Paint Matt Black is a ready for use, high opacity, fast drying alkyd resin based coating with a matt black appearance. Once through dried, it offers good resistance to grease, oils and water etc.
- Specifically designed to cover scuffs and minor blemishes on the side walls of tyres
- Ease of use
- High opacity, normally covers in one coat
HMG Tyre Paint Matt Black is a ready for use, high opacity, fast drying alkyd resin based coating with a matt black appearance. Once through dried, it offers good resistance to grease, oils and water etc.
- Tyre Paint Matt Black must not be used for coating the tread profile of tyres
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- Specifically designed to cover scuffs and minor blemishes on the side walls of tyres
- Ease of use
- High opacity, normally covers in one coat
Product Specification
Technical Data | |
---|---|
Volume Solids: | 9.2% |
VOC Content: | 0.63kgs/ltr |
SG: | - |
Viscosity (Kinematic): | 13 s (DIN 53211/4) |
Density: | 0.894 g/cm³ |
Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. |
Shelf Life: | 12 months from delivery date in original sealed containers. |
Flash Point: | 24°C |
Film Thickness Range And Coverage
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | ||
Brush: | 12 µm | 40 µm |
Coverage: 9.0 square metres per litre @ 25 microns dft
- HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
- These values are a guide only and are not to be used as specifications.
- Film thickness will vary depending on actual use and specification.
- Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.
Drying Times
Drying Times At 20°C | |
---|---|
Touch Dry: | 20 minutes |
Dry To Recoat: | After flash off |
Fully Cured: | 16 hours |
Surface Preparation
- Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
Application Methods
Technical Data | |||||
---|---|---|---|---|---|
Brush | |||||
Mixing Ratio: | Ready for use | ||||
- | |||||
Thinner Options: | n/a | ||||
- | |||||
Viscosity: | 15 - 20 seconds B4 cup | ||||
Number Of Coats (Guide Only): | As required | ||||
Flash Off: | 10 minutes |
Product Notes
Information on basic physical and chemical properties | |
---|---|
Form: | Liquid |
Colour: | Black |
Odour: | Characteristic |
Odour Threshold: | Not determined |
pH-value: | Not determined |
Change in Condition | |
Melting point/freezing point: | Undetermined |
Initial boiling point and boiling range: | 135°C |
Flash Point: | 24°C |
Flammability (solid, gas): | Not applicable |
Ignition temperature: | 200°C |
Decomposition temperature: | Not determined. |
Auto-ignition temperature: | Product is not selfigniting |
Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." |
Explosion limits: Lower: | 0.6 Vol % |
Explosion limits: Upper: | 7.0 Vol % |
Vapour pressure at 20°C: | 6.7 hPa |
Density at 20°C: | 0.894 g/cm³ |
Relative density: | Not determined |
Vapour density: | Not determined |
Evaporation rate: | Not determined |
Solubility in / Miscibility with water: | NOT MISCIBLE |
Partition coefficient: n-octanol/water: | Not determined |
Viscosity: Dynamic at 20°C: | Not determined |
Viscosity: Kinematic: | 13 s (DIN 53211/4) |
Solvent content: Organic solvents: | 72.5% |
Solids content: | 9.2% |
Health & Safety
- Refer to the safety data sheet in the attachments section above and tin label prior to use.
Data sheet
- Manufacturer
- HMG Paints Limited
- Water / Solvent Based
- Solvent
- For Use On
- Metal
- Application Method
- Brush
- Sheen
- Matt
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Single
- Pack Size
- 5L
- Base Type
- Alkyd Resin
- Mixing Ratio
- Ready For Use
- Touch Dry (at 20°C)
- 20 Mins
- Dry to Recoat (at 20°C)
- After Flash Off
- Fully Cured (at 20°C)
- 16 Hours
- Density
- 0.894 g/cm³
- Solids by Volume
- 9.2 %
- VOC
- 0.63kgs/ltr
- Shelf Life (from date of manufacture)
- 12 months from delivery date in original sealed containers.
- Recommended Dry Film Thickness
- 12 µm
- Recommended Wet Film Thickness
- 40 µm
- UN Number
- UN1263
- Base Type
- Solvent-Based
- Base Type
- Alkyd Resin
- Suitable For Use On
- Tyres
- Finish
- Matt
- Application Method
- Brush
- Product Usage Type
- Topcoat
- Colour Family
- Black
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG Tyre Paint Matt Black is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT