- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
HMG Cellulose APS Primer is a quick drying cellulose primer for use in aerosols, classic car refinish and industrial applications.
- Available in grey or white
- Also available as an aerosol, please see HMG Cellulose APS Primer Aerosol
HMG Synthetic LP Primer is a quick drying cellulose primer for use in aerosols, classic car refinish and industrial applications.
- Not to be used in connection with 2004/42/CE.
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- Available in grey or white
Product Specification
Technical Data | ||||||
---|---|---|---|---|---|---|
Cellulose APS1 Primer | Cellulose APS2 White Primer Filler | |||||
Volume Solids: | 41.5% | 54.0% | ||||
VOC Content: | 0.670Kg/L | 0.670Kg/L | ||||
SG: | - | - | ||||
Viscosity: | Not determined | 200 mPas | ||||
Density: | 1.202 g/cm³ | 1.205 g/cm³ | ||||
Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. | Store between 5°C - 25°C. When not in use, cans must be kept sealed. | ||||
Shelf Life: | 12 months from delivery date in original sealed containers. | 12 months from delivery date in original sealed containers. | ||||
Pot Life: | - | - | ||||
Flash Point: | 4°C | 4°C |
Film Thickness Range And Coverage
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | ||
Compliant Spray Gun: | 30 - 50 μm | 60 - 100 μm |
Coverage: 20 square metres per litre @ 20 microns dft (Theoretical)
- HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
- These values are a guide only and are not to be used as specifications.
- Film thickness will vary depending on actual use and specification.
- Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.
Drying Times
Drying Times At 20°C | |
---|---|
Touch Dry: | 10 minutes |
Dry To Recoat: | After 30 minutes |
Fully Cured: | 30 minutes |
Surface Preparation
- Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
- Read and follow the Safety Data Sheet, Product Data Sheet and label instructions.
- Stir all paints thoroughly before use.
- Always use the same batch number on the same job.
- Check colour & sheen.
- Filter the product immediately before use.
- Reduce emissions and maintain quality by replacing tin lid after use.
Application Methods
Technical Data | |||||
---|---|---|---|---|---|
Compliant Spray Gun | |||||
Mixing Ratio: | Base: 1 | ||||
Thinner: 1 | |||||
Thinner Options: | Thinner 2641 | ||||
Thinner 2642 | |||||
Viscosity: | 28 - 35 seconds B4 cup | ||||
Spray Gun Setup: | - | ||||
Number Of Coats (Guide Only): | 2 - 3 coats | ||||
Flash Off: | 5 minutes between coats |
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
Product Notes
Information On Basic Physical And Chemical Properties | ||||||
---|---|---|---|---|---|---|
Cellulose APS1 Primer | Cellulose APS2 White Primer Filler | |||||
Form: | According to product specification | According to product specification | ||||
Colour: | According to product specification | According to product specification | ||||
Odour: | Characteristic | Characteristic | ||||
Odour Threshold: | Not determined | |||||
pH-value 20°C: | Not determined | Not determined | ||||
Melting point/freezing point: | Undetermined | Undetermined | ||||
Initial boiling point and boiling range: | 78°C | 82°C | ||||
Flash Point: | 4°C | 4°C | ||||
Flammability (solid, gas): | Not applicable | Not applicable | ||||
Ignition temperature: | 370°C | 370°C | ||||
Decomposition temperature: | Not determined. | Not determined. | ||||
Auto-ignition temperature: | Product is not selfigniting. | Product is not selfigniting. | ||||
Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." | ||||
Explosion limits: Lower: | 1.2 Vol % | 1.1 Vol % | ||||
Explosion limits: Upper: | 7.0 Vol % | 7.0 Vol % | ||||
Vapour pressure at 20°C: | 29 hPa | 6.7 hPa | ||||
Density at 20°C: | 1.202 g/cm³ | 1.205 g/cm³ | ||||
Relative density: | Not determined | Not determined | ||||
Vapour density: | Not determined | Not determined | ||||
Evaporation rate: | Not determined | Not determined | ||||
Solubility in / Miscibility with water: | NOT MISCIBLE | NOT MISCIBLE | ||||
Partition coefficient: n-octanol/water: | Not determined | Not determined | ||||
Viscosity: Dynamic at 20°C: | Not determined | 200 mPas | ||||
Viscosity: Kinematic: | Not determined | Not determined | ||||
Solvent content: Organic solvents: | 47.2% | 46.9% | ||||
Solids content: | 41.5% | 54.0% |
Health & Safety
- Refer to the safety data sheet in the attachments section above and tin label prior to use.
- Suitable respiratory equipment should be worn when spraying.
Data sheet
- Manufacturer
- HMG Paints Limited
- Water / Solvent Based
- Solvent
- For Use On
- Metal
- Application Method
- Spray
- Sheen
- Matt
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Single
- Pack Size
- 1L, 5L
- Mixing Ratio
- Base: 1 - Thinner: 1
- Touch Dry (at 20°C)
- 10 Mins
- Dry to Recoat (at 20°C)
- After 30 mins
- Fully Cured (at 20°C)
- 30 Mins
- Coverage
- 20 square metres per litre @ 20 microns dft
- Recommended Thinner/Cleaner
- Thinner 2641 - Thinner 2642
- Density
- Cellulose APS1 Primer: 1.202 g/cm³ - Cellulose APS2 White Primer Filler: 1.205 g/cm³
- Solids by Volume
- Cellulose APS1 Primer: 41.5 % - Cellulose APS2 White Primer Filler: 54.0 %
- Heat Resistance (up-to)
- 80°C
- VOC
- 0.670kgs/ltr
- Recommended Dry Film Thickness
- 30 - 50 μm
- Recommended Wet Film Thickness
- 60 - 100 μm
- UN Number
- UN1263
- Base Type
- Solvent-Based
- Suitable For Use On
- Metal
- Finish
- Matt
- Application Method
- Spray
- Product Usage Type
- Primer
- Product Range
- Cellulose
- Colour Family
- White
- Colour Family
- Grey
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG Cellulose APS Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Thinner 2641
HMG Thinner 2641 is a medium fast thinner. Designed for use with cellulose based systems.
HMG Thinner 2642
HMG Thinner 2642 is a medium slow thinner which can be used with compatible HMG systems. For use with cellulose based systems.
HMG Cellulose APS Primer Aerosol
HMG Cellulose APS Primer Aerosol is a quick drying cellulose primer for use in aerosols, classic car refinish and industrial applications. This product is also available in non-aerosol form, please see HMG Cellulose APS Primer. 400ml/16oz Aerosol Matt finish Available in grey (APS2) or white (APS1) Please note: Not to be used in...
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...