Follow us on:

HMG Uplas Primer

HMG Uplas Primer

PRIUPLAS
HMG4432

HMG Uplas Primer is a 1K coating specifically designed to promote adhesion to various plastic substrates. It is quick drying and can be overcoated with a wide variety of HMG systems.

  • A 1K coating specifically designed to promote adhesion to various plastic substrates
  • Quick drying
  • Can by overcoated with a wide variety of HMG systems
  • Also available as an aerosol, please see HMG Uplas Primer Aerosol
Colour
Size
Finish
£33.16(incl. VAT)
£27.63(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

HMG Uplas Primer is a 1K coating specifically designed to promote adhesion to various plastic substrates. It is quick drying and can be overcoated with a wide variety of HMG systems.



Click To Jump To Section:




Features & Benefits


  • A 1K coating specifically designed to promote adhesion to various plastic substrates.
  • Quick drying
  • Can by overcoated with a wide variety of HMG systems.



Product Specification


Technical Data
Uplas Primer
Volume Solids: 5.5%
VOC Content: 0.820 Kg/l
SG: -
Viscosity: 300 mPas
Density: 0.875 g/cm³
Storage Conditions: Store between 5°C - 25°C. When not in use, cans must be kept sealed.
Shelf Life: 12 months from delivery date in original sealed containers.
Pot Life: -
Flash Point: 4°C



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness
Compliant Spray Gun: 2 μm 35 μm



Coverage: 30 square meters per litre @ 15 microns dft (Theoretical)

  • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
  • These values are a guide only and are not to be used as specifications.
  • Film thickness will vary depending on actual use and specification.
  • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



Drying Times


Drying Times At 20°C
Touch Dry: 5 minutes
Dry To Recoat: Minimum 30 minutes.
Fully Cured: 30 minutes



Surface Preparation


  • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
  • Read and follow the safety data sheet, product data sheet and label instructions.
  • Stir all paints thoroughly before use.
  • Always use the same batch number on the same job.
  • Check colour & sheen.
  • Filter the product immediately before use.
  • Reduce emissions and maintain quality by replacing tin lid after use.



Application Methods


Technical Data
Compliant Spray Gun
Mixing Ratio: Ready for use
-
Thinner Options: -
Viscosity: 23 seconds B4 cup
Spray Gun Setup: 1.4 - 1.6
Number Of Coats (Guide Only): 1 coat
Flash Off: -



For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



Product Notes


Information On Basic Physical And Chemical Properties
Uplas Primer
Form: According to product specification
Colour: According to product specification
Odour: Characteristic
Odour Threshold: Not determined
pH-value 20°C: Not determined
Melting point/freezing point: Undetermined
Initial boiling point and boiling range: 110°C
Flash Point: 4°C
Flammability (solid, gas): Not applicable
Ignition temperature: 432°C
Decomposition temperature: Not determined.
Auto-ignition temperature: Product is not selfigniting.
Explosive properties: "Product is not explosive. However, formation of explosive air vapour mixtures are possible."
Explosion limits: Lower: 1.0 Vol %
Explosion limits: Upper: 7.1 Vol %
Vapour pressure at 20°C: 29 hPa
Density at 20°C: 0.875 g/cm³
Relative density: Not determined
Vapour density: Not determined
Evaporation rate: Not determined
Solubility in / Miscibility with water: NOT MISCIBLE
Partition coefficient: n-octanol/water: Not determined
Viscosity: Dynamic at 20°C: 300 mPas
Viscosity: Kinematic: Not determined
Solvent content: Organic solvents: 21.8%
Solids content: 5.5%



Health & Safety


  • Refer to the safety data sheet in the attachments section above and tin label prior to use.
  • Suitable respiratory equipment should be worn when spraying.

Click to go back to the top of the page

Product Details
4432-685831

Data sheet

Manufacturer
HMG Paints Limited
For Use On
Plastic
Application Method
Spray
Sheen
Matt
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Pack Size
1L
Mixing Ratio
RFU
Touch Dry (at 20°C)
5 Mins
Dry to Recoat (at 20°C)
Minimum 30 mins.
Fully Cured (at 20°C)
30 Mins
Density
0.875 g/cm³
Solids by Volume
5.5 %
VOC
0.820 Kg/l
Finish
Matt
Size
1L
Recommended Dry Film Thickness
2 μm
Recommended Wet Film Thickness
35 μm
UN Number
UN1263
Suitable For Use On
Plastic
Finish
Matt
Application Method
Spray
Product Usage Type
Primer
Colour Family
Beige
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

HMG Uplas Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like