Follow us on:

HMG Polyester Spray Filler KF8 | Automotive Paint & Wood Preparation

HMG Polyester Spray Filler KF8

PRIPOLKF8
HMG4455

HMG Polyester Spray Filler KF8 is a 2K heavy bodied sprayable filler which can be used for the deep filling of substrates of various types.

  • Two part system - 5L base with 500ml hardener
  • Used extensively in the automotive re-finishing field, where its ultra high build and quick curing make it ideal for use in repair situations
  • Other uses include as a high build grain filler for rough timber, and as an effective sealer for fibreboard & MDF chipboard
Colour
Size
Finish
£191.15(incl. VAT)
£159.29(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

HMG Polyester Spray Filler KF8 is a 2K heavy bodied sprayable filler which can be used for the deep filling of substrates of various types.



Click To Jump To Section:




Features & Benefits


  • Used extensively in the automotive re-finishing field, where its ultra high build and quick curing make it ideal for use in repair situations.
  • Other uses include as a high build grain filler for rough timber, and as an effective sealer for fibreboard & MDF chipboard.



Product Specification


Technical Data
HMG Polyester Spray Filler KF8
Volume Solids: 70.0%
VOC Content: 0.380kgs/ltr
SG: -
Viscosity: 500 mPas
Density: 1.52 g/cm³
Storage Conditions: Store between 5°C - 25°C. When not in use, cans must be kept sealed.
Shelf Life: 12 months from delivery date in original sealed containers.
Pot Life: 20 minutes
Flash Point: 31°C



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness
Compliant Spray Gun: 100 μm
Airless/Air-Assisted: 100 μm



Coverage: n/a

  • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
  • These values are a guide only and are not to be used as specifications.
  • Film thickness will vary depending on actual use and specification.
  • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



Drying Times


Drying Times At 20°C
Touch Dry: 20 minutes at 20°C
Touch Dry: 5 minutes at 60°C
Dry To Recoat: Can be used as a wet on wet system.
Fully Cured: 2 hours at 20°C
Fully Cured: 20 minutes at 60°C



Surface Preparation


  • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
  • Read and follow the safety data sheet, product data sheet and label instructions.
  • Stir all paints thoroughly before use.
  • Always use the same batch number on the same job.
  • Check colour & sheen.
  • Filter the product immediately before use.
  • Reduce emissions and maintain quality by replacing tin lid after use.



Application Methods


Technical Data
Compliant Spray Gun Brush HVLP
Mixing Ratio: Base: 10 Base: 10 Base: 10
Hardener: 1 Hardener: 1 Hardener: 1
Thinner: up to 25% Thinner: - Thinner: up to 25%
Hardener Options: KF8 Hardener KF8 Hardener KF8 Hardener
Thinner Options: Thinner 2600 Thinner 2600 Thinner 2600
Viscosity: - - -
Spray Gun Setup: Dependant on application - Dependant on application
Number Of Coats (Guide Only): 1 heavy coat 1 heavy coat 1 heavy coat
Flash Off: - - -



For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



Product Notes


Information On Basic Physical And Chemical Properties
HMG Polyester Spray Filler KF8
Form: According to product specification
Colour: According to product specification
Odour: Characteristic
Odour Threshold: Not determined
pH-value 20°C: Not determined
Melting point/freezing point: Undetermined
Initial boiling point and boiling range: 145°C
Flash Point: 31°C
Flammability (solid, gas): Not applicable
Ignition temperature: 480°C
Decomposition temperature: Not determined.
Auto-ignition temperature: Product is not selfigniting.
Explosive properties: "Product is not explosive. However, formation of explosive air vapour mixtures are possible."
Explosion limits: Lower: 1.2 Vol%
Explosion limits: Upper: 8.9 Vol%
Vapour pressure at 20°C: 6 hPa
Density at 20°C: 1.52 g/cm³
Relative density: Not determined
Vapour density: Not determined
Evaporation rate: Not determined
Solubility in / Miscibility with water: NOT MISCIBLE
Partition coefficient: n-octanol/water: Not determined
Viscosity: Dynamic at 20°C: 500 mPas
Viscosity: Kinematic: Not determined
Solvent content: Organic solvents: 30.1%
Solids content: 70.0%



Health & Safety


  • Refer to the safety data sheet in the attachments section above and tin label prior to use.
  • Suitable respiratory equipment should be worn when spraying.
  • Contaminated Rags, Spray Booth Filters or other substrates should be segregated from other chemical waste, soaked with Water and disposed of in a non-combustible container with a tight fitting Lid.

Click to go back to the top of the page

Product Details
4455-697674

Data sheet

Manufacturer
HMG Paints Limited
Water / Solvent Based
Solvent
For Use On
Metal, Timber, fibreboard, MDF
Application Method
Spray
Sheen
Matt
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Two-Pack
Pack Size
5L
Touch Dry (at 20°C)
20 minutes
Touch Dry (at 20°C)
2 hours
Dry to Handle (at 20°C)
100 μm
Dry to Recoat (at 20°C)
Can be used as a wet on wet system.
Fully Cured (at 20°C)
2 hours
Pot Life (at 20°C)
20 minutes
Recommended Thinner/Cleaner
Base: 10 - Hardener: 1 - Thinner: up to 25%
Recommended Thinner/Cleaner
Thinner 2600
Density
1.52 g/cm³
Solids by Volume
70.0%
Heat Resistance (up-to)
Intermittently to 120°C
VOC
0.380kgs/ltr
Shelf Life (from date of manufacture)
12 months from delivery date in original sealed containers.
Touch Dry
5 minutes at 60°C
Fully Cured
20 minutes at 60°C
Base Type
Solvent-Based
Suitable For Use On
Timber
Suitable For Use On
Metal
Suitable For Use On
MDF
Suitable For Use On
Fibreboard
Finish
Matt
Application Method
Spray
Product Usage Type
Basecoat
Colour Family
White
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

HMG Polyester Spray Filler KF8 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like
HMG Thinner 2600 | Solvent & Thinner

HMG Thinner 2600

HMG Thinner 2600 is a very fast thinner. For use in recommended HMG systems.

Price £48.01 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery
Hand & Power Tool Surface Preparation Kits for Steel

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £25.93 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery