Hi can I paint red tarmac with black paint what would you recommend

This product could be applied over the existing red coloured tarmac, however may struggle to cover the colour fully and could require more than 2 coats to achieve this. As an alternative, assuming the substrate is clean, dry, sound and prepared as detailed in the technical datasheet, Rust-Oleum Tarmacoat could be an alternative option. This product provides a higher film build and give a better option to hide any red colour.

Hi, my tarmacadam driveway is 10 years down now and looking very grey. Which of your two products is best to bring it back looking fresh again. I notice there is a big price difference between the two products so what is the difference Tarma coat and Asphalt restorer?

Rust-Oleum 5478 Asphalt Restorer is a bitumen based product containing filler to revive the orginal tarmac. Rust-Oleum Tarmacoat is a waterbased acrylic paint that is available in a larger selection of colours.

Hi would this go soft when the weather is hot? I have heard of similar products doing this . Thanks

Asphalt can soften with increases in temperature. Rust-Oleum 5478 Asphalt Restorer is intended as a surface coating. Depending on the substrate it could soften surfaces which contain coal tar. We would recommend to apply a test area and check after 24 hours that no softening has occurred.

can brushies be cleaned out with water? is it self leveling?,and when u say matt does it have just a very slight sheen ? thx

Rust-Oleum 5478 Asphalt Restorer is a solvent based coating so brushes cannot be cleaned with water. It contains fillers and special flow additives, the product should be applied generously but evenly in one coat using a roller or brush. Small pits and fissures can be filled with a stiff mortar consisting of dry sand mixed with the product. Pits and fissures should be primed with the product before trowelling in the mortar. The product is classed as a matt finish.

Will this product leave the tarmac slippery when wet

It has no specific anti-slip properties or test data on this but it is a matt finish and if applied properly shouldn't increase the risk of slipping on the surface.

can i paint this over freshly layed cold lay tarmac or do i have to wait for it to cure?

The newly laid tarmac would need to cure first.

Approximately what area will a 5l tin cover?

5 - 10m² per 5 litre, depending on the surface.

Hi My messy builders have left ivory tyrolean on the tarmac pavement Will this product paint over and disguise this?

Yes, we think this should be OK. First be sure to thoroughly wash and clean the area (preferably by pressure washer) to remove as much of the staining as possible. Then ensure any remnants are completely dry and cured and unable to be removed. Test a small area first to ensure no adverse reactions, if OK apply 1-2 coats as required.

can this product be used on concrete

No, but Rust-Oleum Tarmacoat can.

I'm trying to get rid of diesel spillage stains from my drive due to a fuel tank breakage would your ash felt restorer do this job? Thanks for your help.

Contamination such as fuel spillages, oils, greases, etc. must be completely removed from surfaces needing to be painted with Rust-Oleum 5478 Asphalt Restorer. If this can be achieved then it should hide any visible discolouration, marks etc. left on the driveway surface to provide a uniform, solid coloured finish. We would however recommend a test area be carried out over the affected areas to ensure full obliteration can be achieved and no reaction occurs with the areas in question due to insufficient cleaning.

Rust-Oleum 5478 Asphalt Restorer

Reference 5478.5

Brand Rust-Oleum

Search ID RUS508

Available in matt black.
Designed to refresh and upgrade asphalt.
For car parks, driveways, footpaths, and bicycle paths.
Covers old line markings and repairs.
Long-lasting finish.
Fast drying within 2-5 hours.

Colour

Black

Size

Finish

£52.25(incl. VAT)

£43.54(ex. VAT)

Quantity

Please choose your colour

In Stock and Available for Delivery (See Delivery Options Below)

ColourPicker Explained

In general we sort colours for products into 2 main groups - ‘Ready Mixed’ and ‘Tinted’.
Tinted colours will always be more expensive than Ready Mixed colours as they need to be produced at the time of order using a tinting machine dispensing colourant into a base*.
During busy periods, this means that tinted colours could take longer, for example – a ready mixed colour ordered on a 3-5 day delivery might arrive within 3 days, however a tinted colour might take the full 5 days to arrive.

To find Ready Mixed colours, search "ready mixed" or select the Ready Mixed 'colour chart'. To see Tinted colours select a colour chart such as RAL, BS, NCS, etc. or search for a colour/hue to see available or related options.

To ensure fair pricing, we split colours into ‘Price Bands’ to group together similar priced colours. If you wish to search for the cheapest tinted colours, always select Price Band 1.

We make every effort to list all available colours, however we also offer a colour match service which can be accessed by contacting our Technical Team on 0113 245 5450 (option 2) or emailing [email protected]

*Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour

Colour reproduction of the Products on the Site is limited by the technology used to deliver web pages and by the colour representation of Customer’s own monitor and computer set-up. We have made every effort to display as accurately as possible the colours of our Products but we cannot guarantee that the colour shown on Customer’s monitor’s display will accurately reflect the colour of the Product on delivery. We recommend that Customer first purchases the smallest Product available or access an industry standard colour chart in person (and not digitally) to ensure that the colour is acceptable for its purposes.

10 questions about the product

Description

Rust-Oleum 5478 Asphalt Restorer - Bitumen Coating for Asphalt

The Asphalt Restorer is a versatile, single-component, high-quality bitumen-based coating designed to rejuvenate old, discoloured, and worn-out asphalt surfaces. Perfect for both residential and commercial applications, this product offers a cost-effective solution to maintain and enhance the aesthetic appeal of your asphalt surfaces without the need for extensive and disruptive re-surfacing.

Features and Benefits

High-Quality Composition: The Asphalt Restorer is made from premium bitumen and fillers with special flow additives, ensuring a smooth and even application.
Wide Range of Applications: Suitable for car parks, driveways, footpaths, and bicycle paths, making it a versatile choice for various outdoor surfaces.
Long-Lasting Finish: Once applied, the coating provides a durable, weather-resistant finish that protects the surface from further damage and degradation.
Easy Application Process: The product can be easily applied using a brush or roller. For small pits and fissures, a stiff mortar mixed with the Asphalt Restorer can be used to fill and prime the surface before applying the coating.
Quick Drying Time: Dries to the touch within 30 minutes and can be recoated within 2-5 hours, allowing for minimal downtime and quick project completion.
Environmental Compliance: The product meets EU regulations for low VOC emissions, making it a safer choice for both the user and the environment.

Application Instructions

Before application, ensure that the surface is clean, dry, and free from loose materials. Moss and other debris should be removed by scraping or jet washing. Stir the coating thoroughly to ensure homogeneity before use. Apply the product generously but evenly using a brush or roller. Protect the freshly applied coating from rain for at least 30 minutes after application to prevent solvent trapping and delayed curing.

Restrictions and Limitations

Surface Compatibility: This product is designed for use on bitumen-based surfaces. It may soften surfaces containing coal tar. Perform a test application in a small area if in doubt.
Application Conditions: Do not apply during rainfall. Ensure the surface is dry and free from contaminants before application.
Health Precautions: Avoid inhalation of vapours and prolonged skin contact. Use appropriate personal protective equipment as detailed in the Safety Data Sheet.

Health and Safety

Health and Safety: The Asphalt Restorer contains hydrocarbons, C9-C12, n-/iso-/cyclo-alkanes, aromatics (2-25%). It is classified as a flammable liquid and vapour (H226), and prolonged exposure may cause organ damage (H372). Use only in well-ventilated areas and avoid release into the environment (H411). In case of contact with skin or eyes, rinse immediately with plenty of water and seek medical advice. The product contains no Diisocyanates. For more detailed safety information, please refer to the downloadable Safety Data Sheet.

Product Details

Reference 508-940328

Data sheet

For Use By: Consumer Use
Interior / Exterior Use: Exterior Use
For Use On: Asphalt
Tarmac
Bitumen
Application Method: Brush
Roller
Colour: Black
Pack Size: 5L
Dry to Recoat (at 20°C): 2 - 5 Hours
Fully Cured (at 20°C): 2 - 5 hours. Rain will delay curing by trapping solvents within the coating.
Coverage: 1-2m² per litre
VOC: 286 g/L
Shelf Life (from date of manufacture): 2 years
Touch Dry: 30mins
UN Number: UN1263
Consumption: 5 - 10 m² per 5 litres, depending on the surface
Base Type: Solvent-Based
Base Type: Bitumen
Suitable For Use On: Carparks
Suitable For Use On: Tarmac
Suitable For Use On: Asphalt
Suitable For Use On: Bituminous Surfaces
Suitable For Use On: Driveways
Suitable For Use On: Paths
Finish: Matt
Application Method: Brush
Application Method: Roller
Components: 1K
Product Usage Type: Topcoat
Fastest Delivery: Next Working Day
Colour Family: Black

Attachments

Download

Product Data Sheet

Download

Safety Data Sheet

Download

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

Name ^*

Email ^*

Question ^*

^* Required fields

I have read and agree to the conditions of use (read)

Derek on 2024-05-21 04:05:46	Question: Hi can I paint red tarmac with black paint what would you recommend
	Answer from Rawlins’ Technical Team: This product could be applied over the existing red coloured tarmac, however may struggle to cover the colour fully and could require more than 2 coats to achieve this. As an alternative, assuming the substrate is clean, dry, sound and prepared as detailed in the technical datasheet, Rust-Oleum Tarmacoat could be an alternative option. This product provides a higher film build and give a better option to hide any red colour.

Shea Hughes on 2020-07-20 19:16:33	Question: Hi, my tarmacadam driveway is 10 years down now and looking very grey. Which of your two products is best to bring it back looking fresh again. I notice there is a big price difference between the two products so what is the difference Tarma coat and Asphalt restorer?
	Answer from Rawlins’ Technical Team: Rust-Oleum 5478 Asphalt Restorer is a bitumen based product containing filler to revive the orginal tarmac. Rust-Oleum Tarmacoat is a waterbased acrylic paint that is available in a larger selection of colours.

Matthew on 2020-04-27 22:09:45	Question: Hi would this go soft when the weather is hot? I have heard of similar products doing this . Thanks
	Answer from Rawlins’ Technical Team: Asphalt can soften with increases in temperature. Rust-Oleum 5478 Asphalt Restorer is intended as a surface coating. Depending on the substrate it could soften surfaces which contain coal tar. We would recommend to apply a test area and check after 24 hours that no softening has occurred.

neil on 2019-09-07 00:20:26	Question: can brushies be cleaned out with water? is it self leveling?,and when u say matt does it have just a very slight sheen ? thx
	Answer from Rawlins’ Technical Team: Rust-Oleum 5478 Asphalt Restorer is a solvent based coating so brushes cannot be cleaned with water. It contains fillers and special flow additives, the product should be applied generously but evenly in one coat using a roller or brush. Small pits and fissures can be filled with a stiff mortar consisting of dry sand mixed with the product. Pits and fissures should be primed with the product before trowelling in the mortar. The product is classed as a matt finish.

matt dunn on 2019-07-16 12:20:33	Question: Will this product leave the tarmac slippery when wet
	Answer from Rawlins’ Technical Team: It has no specific anti-slip properties or test data on this but it is a matt finish and if applied properly shouldn't increase the risk of slipping on the surface.

andrew finch -dent on 2019-03-17 16:13:24	Question: can i paint this over freshly layed cold lay tarmac or do i have to wait for it to cure?
	Answer from Rawlins’ Technical Team: The newly laid tarmac would need to cure first.

Alan Harding on 2018-09-18 14:20:30	Question: Approximately what area will a 5l tin cover?
	Answer from Rawlins’ Technical Team: 5 - 10m² per 5 litre, depending on the surface.

Gwyn Matthews on 2018-08-16 05:38:57	Question: Hi My messy builders have left ivory tyrolean on the tarmac pavement Will this product paint over and disguise this?
	Answer from Rawlins’ Technical Team: Yes, we think this should be OK. First be sure to thoroughly wash and clean the area (preferably by pressure washer) to remove as much of the staining as possible. Then ensure any remnants are completely dry and cured and unable to be removed. Test a small area first to ensure no adverse reactions, if OK apply 1-2 coats as required.

jvjones on 2018-07-22 10:42:43	Question: can this product be used on concrete
	Answer from Rawlins’ Technical Team: No, but Rust-Oleum Tarmacoat can.

Dave parkes on 2017-05-28 10:07:10	Question: I'm trying to get rid of diesel spillage stains from my drive due to a fuel tank breakage would your ash felt restorer do this job? Thanks for your help.
	Answer from Rawlins’ Technical Team: Contamination such as fuel spillages, oils, greases, etc. must be completely removed from surfaces needing to be painted with Rust-Oleum 5478 Asphalt Restorer. If this can be achieved then it should hide any visible discolouration, marks etc. left on the driveway surface to provide a uniform, solid coloured finish. We would however recommend a test area be carried out over the affected areas to ensure full obliteration can be achieved and no reaction occurs with the areas in question due to insufficient cleaning.

IMPORTANT SHIPPING & DELIVERY INFORMATION

Rust-Oleum 5478 Asphalt Restorer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT

Floor Application Kit

Floor Application Kit from Rawlins Paints provides all the application equipment needed to apply conventional floor paints and coatings to a professional standard. The application of floor coatings is often crucial to their performance, so it is important to use the right tools to ensure a lasting finish. Each kit contains: 12" Roller,...

£101.80 (incl. VAT)

Shop now

In Stock and Available for Delivery

Follow us on:

Rust-Oleum 5478 Asphalt Restorer

Rust-Oleum 5478 Asphalt Restorer

Rust-Oleum 5478 Asphalt Restorer - Bitumen Coating for Asphalt

Features and Benefits

Application Instructions

Restrictions and Limitations

Health and Safety

Data sheet

Questions

Question about the product

IMPORTANT SHIPPING & DELIVERY INFORMATION

Floor Application Kit