- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
HMG Z4381 Single Pack Acrylic Lacquer Aerosol is an air drying Clearcoat supplied as an Aerosol. It is ideally suited for use where localised and spot repair work is necessary. This product is also available in non-aerosol form for compliant spray gun application, please see HMG Z4381 Single Pack Acrylic Lacquer.
- 400ml/16oz Aerosol
- Quick drying - touch dry in 5 minutes @20°C
- Ease of use
- Coverage of 6.0 square metres per litre @ 25 microns dft
- Please note: It is not advisable to do overall resprays with this material
HMG Z4381 Single Pack Acrylic Lacquer Aerosol is an air drying Clearcoat supplied as an Aerosol. It is ideally suited for use where localised and spot repair work is necessary. This product is also available in non-aerosol form for compliant spray gun application, please see HMG Z4381 Single Pack Acrylic Lacquer.
It is not advisable to do overall resprays with this material.
Click To Jump To Section:
- Features & Benefits
- Drying Times
- Surface Preparation
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- 400ml/16oz Aerosol
- Quick drying - touch dry in 5 minutes @20°C
- Ease of use
- Coverage of 6.0 square metres per litre @ 25 microns dft
- Please note: It is not advisable to do overall resprays with this material
Drying Times
Drying Times At 20°C/RH 50% | |
---|---|
Touch Dry: | 5 minutes |
Hard Dry: | 60 minutes |
Surface Preparation
- Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants
- Always use the same batch number on the same job
- Check colour & sheen
- Filter the product immediately before use
- Reduce emissions and maintain quality by replacing tin lid after use
Application Methods
Technical Data | ||||
---|---|---|---|---|
Aerosol | ||||
Mixing Ratio: | Ready for use | |||
Thinner Options: | N/A | |||
Viscosity: | N/A | |||
Spray Gun Setup: | N/A | |||
Number Of Coats (Guide Only): | 3 - 4 coats | |||
Flash Off: | 5 minutes between coats |
Product Notes
Information on basic physical and chemical properties | ||||
---|---|---|---|---|
Form: | Aerosol | |||
Colour: | According to product specification | |||
Odour: | Characteristic | |||
Odour Threshold: | Not determined | |||
pH-value: | Not determined | |||
Change in Condition | ||||
Melting point/freezing point: | Undetermined | |||
Initial boiling point and boiling range: | 80°C | |||
Flash Point: | -42°C | |||
Flammability (solid, gas): | Not applicable | |||
Ignition temperature: | 235°C | |||
Decomposition temperature: | Not determined | |||
Auto-ignition temperature: | Product is not selfigniting | |||
Explosive properties: | Heating may cause an explosion | |||
Explosion limits: Lower: | 1.2 Vol % | |||
Explosion limits: Upper: | 18.6 Vol % | |||
Vapour pressure at 20°C: | 5200 hPa | |||
Density at 20°C: | 0.751 g/cm³ | |||
Relative density: | Not determined | |||
Vapour density: | Not determined | |||
Evaporation rate: | Not determined | |||
Solubility in / Miscibility with water: | NOT MISCIBLE | |||
Partition coefficient: n-octanol/water: | Not determined | |||
Viscosity: Dynamic at 20°C: | Not determined | |||
Viscosity: Kinematic: | Not determined | |||
Solvent content: Organic solvents: | 91.7% | |||
Solids content: | 8.2% |
Health & Safety
- Refer to the safety data sheet in the attachments section above and tin label prior to use
- Suitable respiratory equipment should be worn when spraying
Data sheet
- Manufacturer
- HMG Paints Limited
- Water / Solvent Based
- Solvent
- For Use On
- Metal
- Application Method
- Aerosol
- Sheen
- Gloss
- Colour
- Clear
- Single, Two or Three Pack
- Single
- Pack Size
- 400ml/16oz Aerosol
- Parts
- One part pack
- Base Type
- Acrylic
- Key Features
- Quick drying - Touch Dry in 5 minutes. Ease of use.
- Touch Dry (at 20°C)
- 5 Mins
- Fully Cured (at 20°C)
- 60 Mins
- Coverage
- 6.0 square metres per litre @ 25 microns dft (Theoretical)
- Density
- 0.904 g/cm³
- Solids by Volume
- 8.2%
- VOC
- 0.751Kg/L
- Shelf Life (from date of manufacture)
- 12 months from delivery date in original sealed containers
- UN Number
- UN1950
- Flashpoint
- -42°C
- Base Type
- Acrylic
- Finish
- Gloss
- Application Method
- Aerosol
- Product Usage Type
- Repair
- Colour Family
- Clear
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG Z4381 Single Pack Acrylic Lacquer Aerosol is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Z4381 Single Pack Acrylic Lacquer
HMG Z4381 Single Pack Acrylic Lacquer is an air drying clearcoat which is supplied ready for use. It is ideally suited for use where localised and spot repair work is necessary. Quick drying - touch dry in 5 minutes Ease of use Clearcoat Also available and an aerosol, please see HMG Z4381 Single Pack Acrylic Lacquer
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...