- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Please Note: To check availability and to order this product please contact our Technical Department on 0113 2455450 (option 2).
Fosroc Lokfix E55S is a two component vinyl-ester anchoring material, supplied in single component cartridges with a static mixer nozzle. When applied it sets and cures rapidly to firmly secure a variety of steel fixings into concrete and masonry substrates.
- For concrete (solid, porous and light), masonry and hollow bricks. Accredited for use in dry, damp and flooded concrete substrates
- C1 seismic resistance and fire rated up to 2 hours
Also available:
- Lokfix E35S based on styrene free polyester for lightweight fixings into concrete and masonry
- Lokfix E75 based on pure epoxy for heavy duty fixings
Quick Links - Click To Jump To Section:
Features & Benefits
- High bond strength
- Rapid return to service
- Can use with good quality skeleton gun (300ml size), e.g Lokfix Application Gun (Manual) E35/55
- No additional mixing equipment required
- Does not apply expansive force to the substrate
- Enables fixings closer to edges than mechanical anchors
- Resistant to a variety of chemicals
- Re-usable by replacing the static mixer, e.g Lokfix Mixer Nozzle E35/55
- Low VOC
- Waterproof, protecting the fixing from corrosion
- Performs over a wide variety of temperatures
- Fire resistance: Up to 120 mins
- Seismic C1 testing as part of EAD 330499-00-0601 for specific fastening sizes
- Please refer to the Product Data Sheet for full details of:
- Properties
- Specification Clause
- Standards Compliance
- Product Installation
- Estimating
- Storage
- Health and Safety
- Design Criteria
- Refer to the data sheets tab above for application guides and ETA fixings for hollow block, post-installed rebar and concrete
Uses
- For concrete (solid, porous and light), masonry and hollow bricks
- Accredited for use in dry, damp and flooded concrete substrates
- Can be used with cracked concrete
- Fixing of post installed reinforcement
- Anchoring of threaded rod fixings
- Anchoring of internal threaded rod sleeves
- Internal, external and submerged conditions
- Can be applied to almost any size of fixing
- For horizontal, vertical and overhead application
- Bonding and surface crack sealing applications
Application Notes
- May be used with good quality skeleton gun (300ml size)
- Supplied in boxes of 12 no. 300ml cartridges, each supplied with a single mixer nozzle
- Cartridge temperature should be between +15 to +30ºC for optimal use. The substrate temperature can vary significantly from the ambient temperature
- Wet resin should be removed from tools and equipment using Fosroc Solvent 105 immediately after use
Gel and Full Curing Times
Substrate Temp | Gel time (minutes) | Fixing Time (minutes) |
---|---|---|
-10ºC | 90 | 1440 |
-5ºC | 90 | 840 |
0ºC | 45 | 420 |
5ºC | 25 | 120 |
10ºC | 15 | 80 |
20ºC | 6 | 45 |
30ºC | 4 | 25 |
35 - 40ºC | 2 | 20 |
Note: the substrate temperature can vary significantly from the ambient temperature. The table is for dry conditions.
Limitations
- Load calculations to be taken by a qualified engineer
- When embedding into hollow masonry it is normally necessary to use hollow block sleeves
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
Data sheet
- Manufacturer
- Fosroc
- For Use By
- Professional Use
- For Use On
- For concrete (solid, porous and light), masonry and hollow bricks
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 300ml
- Application
- Pour
- Coverage
- Please see the Product Data Sheet - Coverage is dependent on hole diameter
- Recommended Thinner/Cleaner
- Fosroc Solvent 102
- Flexural Strength (at 20°C)
- (EN196) 30MPa
- Max. Application Temperature
- 30ºC
- Min. Application Temperature
- 15ºC
- Density
- 1.74kg/L
- Heat Resistance (up-to)
- Permanent 50°C, temporary 80°C
- Shelf Life (from date of manufacture)
- 300ml cartridges have a maximum shelf life of 12 months when kept in a dry warehouse at between +5 to +25ºC
- Compressive Strength
- (EN196) 70MPa
- Suitable For Use On
- Masonry
- Suitable For Use On
- Concrete
- Application Method
- Application Gun
- Manufacturer
- Fosroc
- Usages
- Anchoring
- Product Usage Type
- Strengthening
- Product Range
- Lokfix
- Categorised As
- Repairs > Low Temperature Bonding and Adhesives
- Seasonal
- Cold Weather
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Fosroc Lokfix E55S is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT