- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Fosroc Renderoc LA is a high performance, free flowing, low alkali micro concrete specifically developed for the repair of large areas of concrete where access is restricted or where reinforcement is congested. Suitable for repair methods 3.2, 4.4, 7.1, 7.2 as defined by BS EN 1504-3.
- For the reinstatement of reinforced concrete where low permeability characteristics are required and where high compressive strength is a consideration.
- Suitable for use where excellent chloride and carbon dioxide resistance is required or for repairs to concrete affected by alkali-silica reaction (ASR)
For use on highways projects, see Fosroc Renderoc LA55 or for deeper repairs see Fosroc Renderoc LA60.
Quick Links - Click To Jump To Section:
Features & Benefits
- Supplied as a ready to use blend of dry powders requiring only the site addition of clean water
- Maximum compatibility with concrete of compressive strength 30 - 60 MPa
- Free-flowing, shrinkage compensated micro-concrete
- Based on Portland cement, graded aggregates and additives which impart controlled expansion in both the plastic and hardened states while minimising water demand
- Low alkali content minimises the risk of alkali-silica reaction
- Alkaline in nature and will protect embedded steel reinforcement
- The hardened product exhibits excellent thermal compatibility with concrete
- Dual expansion system compensates for shrinkage in the plastic and hardened states
- Low alkali content minimises risk of alkali-silica reaction
- Exceptional bond to concrete substrates without independent primer
- Suitable for placement by pumping or pouring techniques into restricted locations
- Self-compacting nature eliminates honeycombing and displaces air without vibration
- High strength and low permeability provide maximum protection against carbon dioxide and chlorides
- Pre-bagged to overcome site-batched variations — only the site addition of clean water is required
- Contains no chloride admixtures
Uses
- Designed for large volume repairs typically in excess of 25mm deep
- Can be applied in sections generally up to 150 mm thick although greater thicknesses may be achievable dependent on the configuration of the repair location and the volume of exposed reinforcing steel
- Suitable for large volume concrete repairs at nominal thicknesses in excess of 25mm
- Can be applied in section thicknesses of 25 - 150mm
- Suitable for repair methods 3.2, 4.4, 7.1, 7.2 as defined by BS EN 1504-3
Application Notes
- Priming of the steel reinforcement is not normally necessary unless it is to remain exposed in an environment likely to cause corrosion after preparation. When required apply one full coat of Nitoprime Zincrich Plus and allow to dry before continuing
- In exceptional circumstances, e.g. where a substrate/repair barrier is required, Nitobond EP bonding aid should be used to prime the substrate
- A forced-action mixer is essential. Mixing in a suitably sized drum using an approved MR3 mixing paddle with a slow speed (400/500 rpm) heavy-duty drill is acceptable
- Pour the mixed material into the prepared formwork in a continuous fashion, ensuring any trapped air at the top of the formwork is released
- Can alternatively be pumped in place using a mortar pump plastering machine (must be capable of handling 4 - 6mm aggregate)
- In cold conditions down to 3°C, the use of warm mixing water (up to 30°C) is advisable to accelerate strength development. At ambient temperatures above 35°C, the material should be stored in the shade and cool water used for mixing
- In common with all cementitious materials, Renderoc LA must be cured immediately after the formwork is stripped in accordance with good concrete practice
- Immediately after striking the formwork, all exposed faces of the repair should be thoroughly soaked with clean water and then sprayed with a liquid curing membrane such as Concure WB, Nitobond AR or Fosroc Cure B
- If the repair is to be overcoated, use Nitobond AR to cure the repair
- Dekguard products may be applied over the repair area without prior removal of the Nitobond AR curing membrane. All traces of form-release oils and curing membranes (other than Nitobond AR) must be removed prior to the application of Dekguard products
- Should be removed from tools, equipment and mixers with clean water immediately after use. Cured material can only be removed mechanically.
- Yield: Approx. 12.0 litres / 25 kg bag
Limitations
- Should not be used when the temperature is below 3°C and falling
- Free-fall mixers must not be used. Mixing of part bags should never be attempted
- The product should not be used to reinstate horizontal areas where the surface would remain unrestrained during cure
- Should not be exposed to moving water during application
- As with other ‘one pack’ repair mortars, Renderoc LA may exhibit satisfactory handling characteristics even though inadequately mixed. This will result in a significantly lower level of performance or possible failure. It is therefore essential that mixing instructions are strictly adhered to with particular emphasis on the quantity of water used and the time of the mixing operation
Data sheet
- Manufacturer
- Fosroc
- For Use By
- Professional Use
- For Use On
- Concrete
- Application Method
- Pour, pump
- Single, Two or Three Pack
- Single
- Pack Size
- 25KG
- Minimum Applied Thickness
- 25mm
- Maximum Applied Thickness
- 150mm
- Maximum Applied Thickness
- 35°C
- Coverage
- Approx. 12.0 litres / 25 kg bag
- Recommended Thinner/Cleaner
- Water
- Compressive Strength (at 20°C)
- @ 1 Day 14 MPa
@ 3 Days 30 MPa
@ 7 Days 42 MPa
@ 28 Days 60 MPa - Flexural Strength (at 20°C)
- 6.9 MPa @ 28 Days
- Min. Application Temperature
- 3°C
- Shelf Life (from date of manufacture)
- 12 months
- Resistance to chemicals
- Renderoc LA severely retards chemical attack in aggressive environments. The cured mortar is impermeable to acid gases, waterborne chloride ions and oxygen.
- Drying time
- Initial set: 6 1/2 hours
Final set: 9 hours - Suitable For Use On
- Concrete
- Application Method
- Pump
- Application Method
- Pour
- Manufacturer
- Fosroc
- Usages
- Cementitious Repair Systems
- Product Usage Type
- Micro-Concrete
- Product Range
- Renderoc
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Fosroc Renderoc LA is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Fosroc Concure WB
Fosroc Concure WB is a water based concrete curing compound based on a low viscosity wax emulsion. For use as a spray applied membrane to retain moisture in concrete for effective curing. Suitable for all general concreting applications and of particular benefit for large area concrete surfaces, such as airport runways, roads and...
Fosroc Cure B
Fosroc Cure B is a spray on temporary curing membrane to retain moisture in freshly placed concrete. Ideal for use as a spray applied membrane to retain moisture in concrete for effective curing Suitable for all general concreting applications and of particular benefit for large area concrete surfaces, such as airport runways, roads and...
Fosroc Nitobond AR
Fosroc Nitobond AR is a single component polymer emulsion and recommended primer for the Renderoc cementitious repair systems. Nitobond AR can be used as a curing membrane and also a concrete surface sealer in non-traffic areas May also be used as an economical dust proofer and surface sealer for non-trafficked cementitious surfaces...
Fosroc Nitobond EP
Fosroc Nitobond EP is a 100% solids solvent-free epoxy resin containing pigments and fine filler. Used for bonding new cementitious mortars and screeds including Patchroc GP and Paveroc to existing cementitious surfaces. Ideal for extensions and repairs to concrete in factories, loading bays, trucking aisles, bridges, roads, bonded or...
Fosroc Nitoprime Zincrich Plus
Fosroc Nitoprime Zincrich Plus is the recommended anti-corrosion primer for exposed steel reinforcement for use with Fosroc concrete repair mortars. Fully compatible with all Renderoc mortars and fluid micro-concretes Complies with LU Standard 1-085 ‘Fire Safety Performance of Materials’. BS EN 1504-7: Reinforcement corrosion protection...
Fosroc Renderoc LA55
Fosroc Renderoc LA55 is a high performance, free flowing, low alkali micro concrete specifically developed for the repair of large areas of concrete where access is restricted or where reinforcement is congested. Suitable for repair methods 3.2, 4.4, 7.1, 7.2 as defined by BS EN 1504-3 and conforms to the requirements of the UK Highways...
Fosroc Renderoc LA60
Fosroc Renderoc LA60 is a high performance, free flowing, low alkali micro concrete specifically developed for the repair of large areas of concrete where access is restricted or where reinforcement is congested. Suitable for repair methods 3.2, 4.4, 7.1, 7.2 as defined by BS EN 1504-3 and conforms to the requirements of the Highways...