- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Fosroc Nitofill WS60 is a two part liquid that reacts when mixed with water to form a rigid, polyurethane foam barrier. Because of the low viscosity and the expansion during polymerisation, the resin will penetrate deep into cracks.
- Stops the flow of water when injected into cracks in concrete in the presence of water
- Provides an effective system for sealing static cracks in wet conditions
Please Note: This product is subject to a lead time of 14-21 Working Days
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
Quick Links - Click To Jump To Section:
Features & Benefits
- Seals against water: reacts and produces foam resistant to water
- Penetrates deep in fine cracks
- Reacts with water and swells exerting pressure on the substrate sealing against water penetration
- Rapid acting, to produce water stop against moving water under pressure
- Free expansion: 1700% - 2200%
- Does not shrink after curing
- Excellent adhesion to mineral construction materials (such as concrete, cement and brick and metal)
- The reaction speed can be controlled by varying the amount of hardener
- Chemically resistant against water, weak acids, and alkali, mineral oils, fungus and bacteria, ground water, sea water and petroleum products
- Re-injectable with Nitofill UR63 to form permanent seal
Application Notes
- Ensure all contact surfaces are free from oil or grease contamination and suitably prepared to allow Nitokit Surface Sealant to bond
- Injection packers should be inserted into holes drilled at a 45 degree angle to the surface such that they intersect the crack. The distance between each packer is typically between 200 mm and 500 mm depending on the width of crack, depth of crack and degree of water penetration / water pressure
- Before commencing ensure the first packer to be injected has its non-return valve fitted. All other packers should be open
- Pre-weigh required quantities of the resin and hardener. Mix together thoroughly using a drill and paddle, mixing only the amount which can be used within the pot life (see Product Data Sheet)
- Pour the mixed material into the hopper of the injection equipment being used. Connect the outlet hose to the first injection packer and activate the pump
- When resin or foam is seen coming from the next injection packer, deactivate the pump immediately and install a nonreturn valve onto the next packer. Move the injection hose to the next packer and repeat until the entire crack is sealed
- Tools and application equipment should be cleaned immediately after use using a proprietary polyurethane cleaner. Once cured, material can only be removed mechanically. Spillages should be absorbed with sand or sawdust and disposed of in accordance with local regulations
- Clean pump and manual equipment every time there is a stop of more than 15 minutes with a proprietary cleaner, or whenever necessary and at the end of the injection. Flush with an extra 1/4 litre of cleaner
Limitations
- Nitofill WS60 is only suitable for filling static cracks, where a more flexible foam is required consider Nitofill UR63
- At high water pressures on wide cracks the product may not be capable of stopping water
- If no water is present in the structure use lowest hardender level and add 1 part water to 4 part resin to the resin component prior to mixing. It is advisable to use disposable cartridges when adding water to avoid obstructing pump equipment and pipes
Data sheet
- Manufacturer
- Fosroc
- For Use By
- Professional Use
- For Use On
- Concrete
- Application Method
- Injection
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 27.3KG
- Density
- Base : 1.1 - 1.2 kg / l
Hardener : 0.947 kg / l - Shelf Life (from date of manufacture)
- 6 months
- Viscosity
- Base : 111 mPas
Hardener : 8 mPas - Suitable For Use On
- Concrete
- Application Method
- Injection
- Manufacturer
- Fosroc
- Usages
- Injection Materials
- Product Usage Type
- Grout
- Product Range
- Nitofill
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Fosroc Nitofill WS60 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Fosroc Nitokit Surface Sealant
Fosroc Nitokit Surface Sealant is a two part filled epoxy is used to seal over the cracks in structural materials such as concrete. Prevents flow-out of resin when injected into cracks, and bonds injection nipples to the surface Also used in evening out substrates and filling blow-holes prior to applying floor and wall epoxy and urethane...
Fosroc Nitofill UR63
Fosroc Nitofill UR63 is a two part liquid polyurethane which reacts to form a tough, slightly flexible resin. It has good adhesion to concrete and masonry and when injected into cracks allows some movement without loss of bond. Flexible foaming two part polyurethane injection resin For injecting into cracks in concrete or masonry in wet...