- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Sikagard 850 Activator is a one-part, ready-to-use primer for Sikagard 850 Clear on coated mineral substrates or wood to improve application and adhesion.
This product is part of the Sikagard Anti-Graffiti System - see System Information.
- Ready to use - no on-site dilution required
- Adhesion promoting primer
- Specifically used with Sikagard 850 Clear
- Free of toluene and other aromatic solvents
Please Note: 0.8kg pack size is made to order with an extended lead time of approximately 14-21 working days
Sikagard 850 Activator is a primer for the Sikagard 850 Anti-Graffiti Coating System on coated mineral substrates or wood.
Quick Links - Click To Jump To Section:
Features & Benefits
- Primer for the Sikagard 850 Anti-Graffiti Coating System on coated mineral substrates or wood
- Ready to use - no on-site dilution required
- Adhesion promoting primer
- Specifically used with Sikagard 850 Clear
- Applied by brush, roller or airless spray
System Information
System Structure
System Part | Product |
---|---|
Primer for uncoated mineral substrates | Sikagard 850 Primer |
Primer for coated mineral substrates or coated wood | Sikagard 850 Activator |
Top coat | Sikagard 850 Clear |
Please note: When applied to bare mineral surface, Sikagard 850 Clear may provide a wet look effect. To reduce/eliminate this effect, the following build-up is recommended:
Sikagard 552W Aquaprimer + Sikagard 850 Activator + Sikagard 850 Clear
Application
Suitable substrates are:
- Coated substrates such as coated concrete, masonry, cementitious render or wood
Important notes:
- On substrates with a rough surface profile, it will be difficult to produce an even coating thickness
- This may result in reduced protection and cleanability
- Pre-levelling or smoothing the surface is recommended before coating application
- Existing coatings must be tested to confirm their compatibility with Sikagard 850 Activator and Sikagard 850 Clear top coat
Surface preparation:
- Substrate must be clean, dry, firmly bonded and free of all contaminants such as dirt, oil, grease and loose friable material which can reduce the adhesion of the coating
- Very smooth substrates may be slightly roughened by light grinding
- Prepare the substrate using light mechanical preparation equipment, steam cleaning or low water pressure
Application:
- Strictly follow installation procedures as defined in method statements, application manuals and working instructions which must always be adjusted to the actual site conditions
- Important: On rough substrates, use a brush to apply primer and make sure the primer covers all the surface including voids
- Note: To prevent air bubbles affecting the finish, do not 'over' brush, roller or spray
- Apply Sikagard 850 Activator evenly over the prepared coating with a brush, fleece roller or airless spray equipment at the required consumption rate
Coverage
- Approximately 50 to 100g/m²
Drying Time
- Note: A drying time of 1 to 2 hours at ambient temperature and 40% relative humidity is required to allow the formation of a consistent primer film
- Note: A higher relative humidity will extend the drying time
- Note: Do not to exceed 5 hours after priming the surface before applying Sikagard 850 Clear
Clean Up
- Clean all tools and application equipment with white spirit immediately after use.
- Hardened material can only be mechanically removed
Health And Safety
For information and advice on the safe handling, storage and disposal of chemical products, users shall refer to the most recent Safety Data Sheet (SDS) containing physical, ecological, toxicological and other safety-related data.
Data sheet
- Manufacturer
- Sika
- For Use By
- Professional Use
- Interior / Exterior Use
- Exterior Use
- Water / Solvent Based
- Solvent
- For Use On
- Coated Mineral Substrates
Wood - Application Method
- Brush
Roller
Airless Spray - Colour
- Clear Yellowish
- Pack Size
- 0.8KG
4KG - Base Type
- Solvent Based
- Coverage
- 50 to 100g/m²
- Recommended Thinner/Cleaner
- White Spirit
- Max. Application Temperature
- 35°C
- Min. Application Temperature
- 8°C
- Density
- ~0.76g/cm³ (at 23°C)
- Shelf Life (from date of manufacture)
- 9 Months
- Touch Dry
- 1-2 hours
- UN Number
- UN1268
- Base Type
- Solvent-Based
- Suitable For Use On
- Wood
- Suitable For Use On
- Mineral Substrates
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Spray
- Manufacturer
- Sika
- Components
- 1K
- Permanent / Semi-Permanent
- Permanent
- Usages
- Concrete Repair
- Product Usage Type
- Anti-Graffiti Coatings
- Product Range
- Sikagard
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Sikagard 850 Activator is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Sikagard 552 W Aquaprimer
Sikagard 552 W Aquaprimer is one component water dispersed adhesion promoting primer for water dispersed polymer paint coatings. It is part of a system that complies with the requirements of EN 1504-2 as protective coating: Priming coat for concrete and dense mineral substrates like fibre cement, aerated concrete, gypsum and smoothing...
Sikagard 850 Clear
Sikagard 850 Clear is a one-part ready to use, polyorganosiloxane based, permanent anti-graffiti and anti-fly poster semi-matt coating. For use on concrete, masonry, cementitious render and coated or uncoated wood. This product is part of the Sikagard Anti-Graffiti System - see System Information. Ready to use - no dilution with solvent at...