The above results must only be used as a general guideline as the slip resistance of a cured resin coating can vary considerably due to many factors including: application technique, variations in film thickness, dispersion of the anti-slip texturing additive and the surface variations of the substrate and location to where it will be applied.

To obtain accurate PTV readings that are site specific (if required) it is strongly recommended that a slip assessment pendulum test is undertaken on each specific site after completion of the installation when the resin has fully cured.

A full copy of the official test report is available upon request.

Coverage

• A 5kg pack is sufficient to treat 8.3-10.0 m² of surface with the recommended two coat treatment, providing an overall d.f.t. of 350-430 microns

Surface Preparation

Concrete:

• Concrete shall be a minimum of 21 days old and/or the residual moisture content shall be below 6%
• Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound, and existing paint finishes
• Blow holes and defective concrete shall be made good using 201 Epoxy Repair Mortar
• Block work walls shall be sealed using 401 Epoxy Floor Primer
• Diamond grinding or shot blasting is the preferred preparation method prior to application as this ensures that a suitable mechanical ‘key’ is achieved

Steel:

• Steel surfaces shall be shot blasted or grit blasted to a nominal Sa 2.5 Swedish standard
• All dust and grease shall be removed prior to coating application
• If a delay is likely to occur between blasting and application then it is recommended that a coat of 404 Epoxy Metal Primer is applied as holding primer to obviate flash rusting

Note: Substrates with high moisture content or oil contamination can still be coated in most instances by the inclusion of one of our specialist primers. Please see 402 Damp Proof Coating and 403 Oil Tolerant Primer for full details.

Priming:

• Porous or dusty surfaces shall be primed using 401 Epoxy Floor Primer
• Damp surfaces shall be primed using 402 Damp Proof Coating
• Please consult the relevant product data sheets for further information

Mixing:

• Pour the contents of the curing agent container into the base container and thoroughly mix, preferably by mechanical means until a uniform colour is achieved

Application Conditions:

• Do not apply to wet or uncured concrete surfaces
• The minimum application temperature is 5°C although please note that curing times will be significantly extended at low temperatures
• Under certain site conditions below 10°C there is a risk of whitening (blooming)

Application

• Apply by brush or roller at a nominal rate of 0.25 to 0.3kg/m²
• After a minimum of 8 hours and before a maximum of 48 hours, apply a second coat at the same rate
• Should a non-slip finish be required, refer to the ‘Slip Resistance’ heading

Cleaning

• Clean equipment with 109 Tool Cleaner prior to curing of the coating

Curing

• Allow to cure for a minimum of 24 hours @ 20°C prior to light foot traffic access and 48 hours @ 20° prior to vehicular trafficking
• 7 days cure @ 20°C is recommended prior to exposure to chemicals
• Good ventilation is essential for satisfactory curing of the coating
• Lower temperatures will extend the curing time

Storage & Shelf Life

• Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 25°C
• 304 HB Epoxy Floor Coating has a minimum shelf life of 12 months when stored in original, unopened containers in accordance with manufacturer’s instructions

Health & Safety

• Avoid contact of the material with skin and eyes
• Wear gloves and goggles
• Wash off splashes immediately with soap and water
• Any eye contamination must be rapidly irrigated with copious amounts of clean water, and immediate medical attention sought
• Please refer to Material Safety Data Sheet for additional Information
• 304 HB Epoxy Floor Coating shall be applied strictly in accordance with the manufacturer’s instructions

For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]