- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
A new type of anti slip resin formulation that can be applied as low as minus 10°C. Most suited for use in heavily trafficked unheated areas such as workshops, warehouses, loading bays and cold stores.
- Two part, anti slip, polyaspartic resin formulation with easy clean, anti slip surface
- Superior performance demonstrated by ISO testing to CE Mark EN1504-2
- Impressive test results for slip resistance, abrasion and impact resistance, as well as for adhesion and hardness
- If a coarser textured finish is required for spillage areas or ramps, please see instead Watco Safety Grip Cold Cure
Note: While great care is taken with the colour samples shown, no guarantee can be given that they represent exactly the colours offered.
Watco Safety Coat Cold Cure is a new type of anti slip resin formulation that can be applied as low as minus 10°C. This high performance coating can be applied in cold conditions where conventional coatings will fail to dry.
It is most suited for use in heavily trafficked unheated areas such as workshops, warehouses, loading bays and cold stores. If a coarser textured finish is required for spillage areas or ramps, please see instead Watco Safety Grip Cold Cure (wet PTV 69).
Safety Coat Cold Cure is extremely resistant to UV and has excellent resistance to weathering, making it a versatile, all year round coating.
The finely textured particles are spherical; this makes it easier to keep clean compared to other anti slip coatings which contain a coarse, more angular type grit.
Safety Coat Cold Cure carries CE Mark EN1504-2 and has impressive test results for slip resistance, abrasion and impact resistance, as well as for adhesion and hardness.
Quick Links - Click To Jump To Section:
Features & Benefits
- Areas of use:
- Production areas
- Warehouses
- Workshops
- Loading bays
- Cold stores, walk-in fridges and freezers
- Interior & exterior
- High performance, two part, anti slip, polyaspartic resin formulation
- asy clean, anti slip surface
- Can be applied at temperatures as low as -10°C and as high as 25°C
- Excellent resistance to UV and weathering
- Fast curing – ready for heavy traffic in just 16 hours
- Superior abrasion and scratch resistance
- Extremely strong – easily copes with forklift trucks
- Superior performance demonstrated by ISO testing to CE Mark EN1504-2
Surface Preparation
Bare concrete – remove surface laitance, dust and any light dirt or grease deposits using Watco Etch & Clean. Watco Etch & Clean also etches smooth, bare concrete surfaces to provide a key. Flush with clean water and allow the surface to dry. For the removal of heavier deposits of oil and grease we recommend Watco Concroff, again, flush with clean water and allow the surface to dry.
New concrete – as a guide, new concrete should be left for eight weeks to dry. The surface should then be prepared using Watco Etch & Clean and thoroughly rinsed away and left to dry prior to applying this coating.
Painted surfaces – abrade to remove any weak or loose paint and check remaining paint is well bonded. Watco Bio-D can be used to remove grease and oil from painted surfaces. Watco Concroff is a very powerful degreaser for contaminated bare concrete, (do not use on a previously painted surface since it can soften paint).
Application in low temperatures – if applying in cold conditions the product should ideally be stored in a warm room for at least 8 hours prior to use. Below 5°C it may be necessary to avoid processes which involve wetting the floor due to the difficulty in drying. A good sweep or mechanical brushing may be sufficient.
Priming – is not usually required, but for open textured, or very porous high suction surfaces, such as sand and cement screed, use Watco Polyaspartic Primer to ensure a uniform finish and to prevent air entrapment bubbles. Watco Polyaspartic Primer should also be used to improve adhesion on smooth (but not power floated) concrete
Metal – remove any rust or flaking material by disc grinding or wire brushing. Apply the coating immediately after preparation to the clean metal surface. Grease or oil can be removed using Watco Bio-D. Allow the metal to dry before coating.
Galvanised Metal – Watco Galvaprime must be used to prepare galvanised metal.
Non-ferrous Metals – for advice, please contact our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Wood – must be sound, clean and dry. If applying to ridged decking, please ensure that the grit particles are spread evenly across the surface.
Mixing
Mix between 10°C and 15°C. Remove the two inner tins from the tall outer tin. Stir each tin thoroughly and pour all of the contents into the outer tin, (scrape around the inside of the tins to remove any residue). Mix the components together thoroughly using a spatula or similar wide bladed tool, (a piece of wooden batten is ideal). At this point add the unit of anti slip polymer additive. Continue mixing until an even colour and consistency are obtained.
Do not mix more than one pack at a time. If a paint stirrer fitted to an electric drill is used, also use the spatula to blend in any unmixed material from the side and bottom of the tin. Do not dilute unless you are stirring in the additive as described under ‘Application in low temperatures’.
Application
Apply between -10°C and 25°C.
Empty the mixed components into a paint tray and apply to the floor using a short pile roller, (not a medium pile or foam), ‘working out’ the coating into a thin paint film. A paint brush can be used for cutting in.
Do not apply the paint too thickly since this will reduce the slip resistant properties and result in reduced coverage. A feature of polyaspartic coatings is that they should be applied as a thin film.
The second coat should be applied as soon as the first coat is dry (generally 6 hours at 20°C), but it must be applied within 5 days. If more than 5 days elapse, the first coat should be lightly abraded.
Test Results
- Abrasion Resistance SO 5470-1 - 187mg
- Impact Resistance ISO 6272 - Class 3 (20Nm)
- Scratch Resistance ISO 4586-2 - 16N
- Adhesion Test ISO 2409 - Class 1
- Adhesion Test EN 1542 - 4.25MPa/Nmm2
- Wolff-Wilborn Hardness Test - 9H
- Flexibility ISO 1519 - 20mm
- Gloss Value - 92
- Chemical Resistance - Very Good
- Water Permeability EN 1062-3 - W3
- Slip Resistance BS7976-2 - 47PTV
Limitations
- Do not apply to damp surfaces
- Do not apply if rainfall is imminent
- Do not apply to power floated surfaces
- Most self-levelling compounds cannot be painted
- Painting chequer paint can be a problem since coatings can wear prematurely off the ‘high spots’
Data sheet
- Manufacturer
- Watco
- For Use By
- Consumer Use
- Interior / Exterior Use
- Interior & Exterior
- For Use On
- Concrete, asphalt (3 months old), sand and cement screeds, well bonded paint, some metals and wood. The moisture content of concrete should be less than 75% RH.
- Application Method
- Short pile roller. Cut in using a brush.
- Sheen
- High gloss, finely textured
- Single, Two or Three Pack
- Three-Pack
- Pack Size
- 2.5L
- Coverage
- 25m2 per coat onto a non-porous surface. If applying in temperatures below 0°C, or onto a textured or porous surface, coverage may be reduced.
- Min. Application Temperature
- -10°C
- Min. Application Temperature
- (-10°C)
- Recommended Dry Film Thickness
- 85 microns
- Recommended Wet Film Thickness
- 100 microns
- Resistance to chemicals
- Petrol
- Resistance to chemicals
- Oil
- Resistance to chemicals
- Diesel
- Resistance to chemicals
- White Spirit
- Resistance to chemicals
- Sugar Solution
- Resistance to chemicals
- Anti-Freeze
- Resistance to chemicals
- Bleach
- Resistance to chemicals
- Ammonia
- Resistance to chemicals
- Detergent
- Resistance to chemicals
- Citric Acid
- Resistance to chemicals
- Caustic Soda
- Resistance to chemicals
- Methylated Spirit
- Resistance to chemicals
- Xylene
- Resistance to chemicals
- Hydraulic Fluids
- Colour(s)
- Standard Colours
- Suitable For Use On
- Production Areas
- Suitable For Use On
- Loading Bays
- Suitable For Use On
- Ramps
- Suitable For Use On
- Warehouses
- Suitable For Use On
- Workshops
- Suitable For Use On
- Workshop Floors
- Suitable For Use On
- Heavy Traffic Areas
- Suitable For Use On
- Metal
- Suitable For Use On
- Bare Concrete
- Suitable For Use On
- Concrete
- Suitable For Use On
- New Concrete
- Suitable For Use On
- Wood
- Suitable For Use On
- Galvanised Metal
- Suitable For Use On
- Previously Painted Surfaces
- Suitable For Use On
- Cold Stores
- Suitable For Use On
- Non-Ferrous Metals
- Suitable For Use On
- Walk-in Fridges
- Suitable For Use On
- Sand and Cement
- Suitable For Use On
- Walk-in Freezers
- Suitable For Use On
- Warehouse Floors
- Suitable For Use On
- Unheated Areas
- Suitable For Use On
- Factory Floors
- Suitable For Use On
- Spillage Areas
- Suitable For Use On
- Workshop Floor
- Application Method
- Roller
- Application Method
- Brush
- Components
- 3K
- Usages
- Low Temperature
- Product Usage Type
- Floor Coating
- Product Range
- Safety Coat
- Colour Family
- White
- Colour Family
- Beige
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Off-White
- Colour Family
- Black
- Anti-Slip Texture
- Fine Texture
- Categorised As
- Floor Paints > Low Temperature Floor Paints
- Seasonal
- Cold Weather
- Product Type
- Polyaspartic
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Watco Safety Coat Cold Cure is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Watco Bio-D Floor Cleaner
A heavy-duty biodegradable cleaner for floor preparation, removes grease and oil from painted or bare concrete. Low odour formula Ideal for preparation to painting Removes oil and grease Can be diluted and used as a general floor cleaner on bare concrete Safe for use on most painted surfaces More Information Delivery Info
Watco Etch & Clean Concrete Surface Preparation
Dual action formula cleans and prepares bare concrete prior to painting. Use on old and new concrete, inside or outside Etches bare concrete to promote adhesion of paint finishes Removes dirt and light oil deposits Removes cement deposits from new concrete to ensure good paint adhesion Reduces alkalinity of new concrete – essential...
Watco Concroff Oil & Grease Remover
Lift grease and oil from bare concrete with this powerful, water-based degreaser. For preparation of heavily contaminated greasy floors prior to painting, inside or outside. Low odour formula Ideal for preparation to painting Removes oil and grease Can be diluted and used as a general floor cleaner on bare concrete Safe for use on most...
Watco Polyaspartic Primer
Primes and seals porous, dusty floors prior to painting, for use with Watco specialist polyaspartic coatings. Primes and seals porous, dusty floors prior to painting Can be used at -10°C to +25°C Ready to overcoat in 4 hours Superior performance demonstrated by ISO testing to CE Mark EN1504-2 Use with the following Watco products: Cold...
Watco Safety Grip Cold Cure
A 3-pack epoxy resin coating designed to provide a safe surface, both inside and out, for steps, ramps and floors, in wet or oily areas. Coarse anti slip finish reduces accidents. Heavy duty with excellent chemical resistance Slip resistant even when wet or oily Easy one coat application for concrete, metal or wood Quick drying in as...