Follow us on:

Sika Parex Epoxy Injection Grout | 2 Part Thixotropic Injection Grout

Sika Parex Thixotropic Injection Grout

660387
SIK9582

Sika Parex Epoxy Injection Grout is a thixotropic two part epoxy resin system. The base resin component is thixotropic plus a low viscosity liquid hardener. The product may be placed using a Tecgrip Gun and Tecgrip Cartridge or may be injected using a suitable hand or mechanical pump. Grouting of gap dimensions 0.1mm to 10mm may be achieved without the use of grout tight shuttering.

  • Two part system gives rapid strength gain obtaining mechanical properties several times those of high quality concrete, and is non shrink enabling complete fill of the grouting area
  • Resistant to most chemicals, stable to sea water, petroleum products and resists freeze thaw cycles

Size
£84.42(incl. VAT)
£70.35(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

Quick Links - Click To Jump To Section:




Features & Benefits


  • Uses:
    • Filling and bonding of cracked concrete where grout leakage may occur
    • Structural support where thin section grouting is required without the use of shuttering
  • Rapid strength gain obtaining mechanical properties several times those of high quality concrete
  • Non shrink enabling complete fill of the grouting area
  • Resistant to most chemicals
  • Stable to sea water & petroleum products
  • Resists freeze thaw cycles
  • Tested in accordance with the relevant parts of BS 6319



Preparation


  • Ensure that grouting surfaces are free from dust and oily contamination
  • Small gaps may be blown out using clean dry compressed air
  • Steel should be free of rust and flaking mill scale
  • All work surfaces must be essentially dry



Mixing


  • Pour all of the hardener from the small bottle into the base container which has sufficient volume to act as the mixing vessel
  • Thoroughly mix the two components until a homogenous thixotropic product is achieved
  • Each pack will yield approximately 1 litre of mixed material



Placing


Supporting Structures

  • The use of a shutter is recommended although the shutter need not be completely grout tight
  • The Epoxy Thixotropic Injection Grout will “stay” once the placing pressure is released
  • The shutter may be constructed from timber and sealed using Rapid Mortar or a suitable silicone sealant
  • Apply a silicone based release agent to the formwork surfaces which will effect release after the grout has hardened
  • Alternatively use thick polyethylene sheet

Crack Injection

  • Drill and fix suitable injection tubes at approximately 300mm centres along the crack-line using Tecgrip CAS Cartridge for fixing the tubes and facing up the crack
  • Allow prepared crack system to harden, approximately 6 hours at 20°C
  • Use a Tecgrip Gun or a low pressure pump to inject mixed grout starting at the lowest point of the crack and work upwards to the highest point sealing off each injection point in turn
  • Place the mixed grout within 25 minutes at 20°C. At the end of the useable time the mix will start to generate a great deal of heat. At this time any unused material should be mixed with sand to reduce the heat output and discarded
  • Allow grout to cure for at least 24 hours
  • Cut off external parts of injection tubes and make good with Polyester Putty
  • Tools and equipment should be cleaned with Solvent prior to grout setting.



Product Details
9582-965812

Data sheet

Manufacturer
Sika
For Use By
Professional Use
Interior / Exterior Use
Interior & Exterior
For Use On
Concrete
Application Method
Tecgrip Gun and Tecgrip Cartridge or may be injected using a suitable hand or mechanical pump
Single, Two or Three Pack
Two-Pack
Pack Size
1.13KG, 6.075KG
Tensile Strength
26 N/mm²
Flexural Strength (at 20°C)
58 N/mm²
Density
1100kg/m3
Shelf Life (from date of manufacture)
12 months
Pot Life
5°C: 80 minutes
10°C: 45 minutes
20°C: 25 minutes
30°C: 10 minutes
Compressive Strength
1 day: 50N/mm2
3 days: 60N/mm2
7 days: 70N/mm2
Suitable For Use On
Concrete
Application Method
Pump
Manufacturer
Sika
Components
2K
Usages
Concrete Repair
Product Usage Type
Injection Resin
Product Range
Parex
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

Sika Parex Thixotropic Injection Grout is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT