Thank you for the enquiry, we have contacted you directly for more information.

Thank you for the enquiry, unfortunatley we do not have a product to recommend for this application.

If you are to use a system with a separate basecoat and topcoat then the topcoat must remain intact to protect the intumescent layer.

Providing the topcoat is regularly checked and maintained then you shouldn’t need to re-apply the intumescent, only the topcoat where needed.

Assuming this is for Universal Beams or Columns then we could recommend Bollom Brosteel Ultra 60 - 60min System For Universal Beams & Columns.

Thank you for the enquiry, we have contacted you directly for more information.

The Ardenbrite range of paints does not provide any level of Fire Protection, we can offer Fire Protection paints for many substrates and have contacted you directly for more information to assist you with this enquiry.

Thank you for the enquiry, please see our detailed blog post Painting the Walls around a Fireplace or Multi Fuel Stove for advice and recommendations.

Thank you for the enquiry, we have contacted you directly for more information.

This is something you would need to check with your fire officer to be certain but if the pipe doesn't pass through the fire rated celing below, I'd assume it wouldn't be required.

Thank you for the enquiry, we have contacted you directly for more information.

I'm afraid we currently have nothing we could recommend for application on to polystyrene to offer any level of fire protection.

To apply for certification, please follow this link Bollom Fire Certificate Application.

Providing you are looking to achieve UK Class 0/Euro Class B, we can recommend Thermoguard Fire Varnish BS Class 1/0 & EN Class B System for your application.

Thank you for the enquiry, we have contacted you directly for more information.

Thank you for the enquiry, please see our detailed blog post on this subject for recommendations. Painting the Walls around a Fireplace or Multi Fuel Stove.

Unfortunately the manufacturers do not produce sample pots, if you require assistance with a specification to fire protect doors please contact our technical team.

Assuming this is standard universal beams and columns in a domestic residential property with steels located in interior, dry environments needing 30 minute protection we would recommend Zeroflame Aquasteel WB+ 30min System for Steel.

We would need to know the composition of the headboard so that we can match it as closely as we can to a test?

Unfortunately we don't have any fire retardant paint for ceiling tiles.

It isn't. Assuming more than just a primer was applied to the steel we would have to recommend complete removal before re-application of a coloured intumescent system.

This would depend on the level of fire protection required (i.e. Class 1, Class 0, 30min, 60min, etc.), the type of wood the ladder is made from and whether it is bare or previously coated?

We can recommend our Thermoguard Door Upgrade packs, with options for already-painted doors and bare timber.

We would recommend Thermoguard Wallcoat 30 & 60 Minute System.

Assuming a Class 1 or Class 0 finish is required we'd recommend Thermoguard Timbercoat BS Class 1/0 & EN Class B System for a coloured paint finish or Thermoguard Fire Varnish BS Class 1/0 & EN Class B System for a clear varnish finish.

Unfortunately we wouldn't be able to offer any products for your application as although we could offer a product to protect the outer fabric, the internal foam wouldn't be compliant.

See Zeroflame Aquasteel WB+ 30min System for Steel.

See Thermoguard Wallcoat BS Class 1/0 & EN Class B System

We would need to know;

• Level of fire protection required (i.e. 30, 60, 90min, etc.)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Environment (internal, external, car park, chemical exposure, etc.)
• Application on site or in shop

Thermoguard Timbercoat BS Class 1/0 & EN Class B System would be our suggestion, the burn marks may need spot priming after cleaning with something like Zinsser B-I-N first so they don't bleed through as a stain. 

In order for us to be able to advise, please provide us with as much of the following information as possible;

• Timber thickness
• Type of timber (i.e. pine, mdf, plywood, etc.)
• Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
• Internal or external
• Use (i.e. floor, wall cladding, ceiling, etc.)

Is any proposed fire protection coating to be applied to the 6mm plywood or the 20mm douglas fir?

You cannot apply fire rated varnishes over previously painted surfaces (existing varnishes and stains are OK but not opaque paints), so you would instead need to apply something like Zeroflame Fire Retardant Paint over the area which you can then overcoat with your own paint (see guidelines on overcoating on the product data sheet) to bring it back to the colour and finish of your choice.

Thank you for your enquiry, to enable us to be able to advise, please provide us with as much of the following information as possible;

• Level of fire protection required (i.e. 30, 60, 90min, etc.)
• Each steel section dimension (i.e. 254x146x37 UB)
• Quantity and length of each section (or overall meterage for each section)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Environment (internal, external, car park, chemical exposure, etc.)
• Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Unfortunately we don't have any fire protection paints specifically for a hose.

No, contact our Technical Team on 0113 2455450 (option 2) to discuss the requirements of your project in more depth.

Thank you for your enquiry, to be able to advise please provide us with as much of the following information as possible;

• Size of surface area to paint
• Timber thickness
• Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
• Type of timber (i.e. pine, mdf, plywood, etc.)
• Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)

Thank you for your enquiry, further to your enquiry, please provide us with as much of the following information as possible;

• Size of surface area to paint
• Timber thickness
• Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
• Type of timber (i.e. pine, mdf, plywood, etc.)
• Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
• Internal or external
• Use (i.e. floor, wall cladding, ceiling, etc.)
• Clear or coloured coating required?
• Bare or previously coated?
• What temperature does it need to withstand while in use

Thank you for your enquiry, further to your enquiry, please provide us with as much of the following information as possible;

• Size of surface area to paint
• Timber thickness
• Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
• Type of timber (i.e. pine, mdf, plywood, etc.)
• Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)

We wouldn't have a product suitable for this application.

Please see available options HERE

We don't have any epoxy products for this application but you could try something like Envirograf Stoveseal to see if this would work for you.

We could only suggest Thermoguard Wallcoat Smoke & Flame Retardant Topcoat for this application. Due to you not knowing exactly how hot the surfaces gets we would suggest trialling a small area to see how it performs before painting the whole area.

Yes, see their range of 'Interchar' products.

We would instead recommend you do not use your fire again until you are able to replace this.

If you are trying to maintain the level of fire protection the render currently has we would instead suggest trialling Thermoguard Wallcoat Smoke & Flame Retardant Topcoat.

Please see details on upgrading solid timber doors HERE.

Thermoguard Wallcoat Smoke & Flame Retardant Topcoat is suitable for interior and exterior use as stated on the information on the product page.

Envirograf do a product called Envirograf Fire Protection Coating for UPVC which may be suitable but we'd need you to contact our Technical Team with some further details on 0113 2455450 (option 2) to confirm.

Thank you for your enquiry, in order for us to be able to advise on which product to select we will need to know what level of fire protection your authority requires - for examples BS Class 1, Class 0, EN Class B, 30min, 60min, etc.

We offer a variety of door upgrade products which can be found HERE.

Please see our Blog post Upgrades For Fire Doors for more information. We would also recommend you contact your relevant authority for advise on this matter.

Assuming that the steel has the required level of fire protection already, the topcoat should be as recommended by the manufacturer of the intumescent paint used. If this is not known, in certain instances on small projects something like Thermoguard Flame Retardant Topcoat could be used if approved by the relevant authority on the project - for larger projects please contact our Technical Team on 0113 2455450 (option 2).

Thank you for your enquiry, in order for us to be able to advise please provide us with as much of the following information as possible;

• Size of surface area to paint
• Timber thickness
• Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
• Type of timber (i.e. pine, mdf, plywood, etc.)
• Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
• Internal or external
• Use (i.e. floor, wall cladding, ceiling, etc.)
• Clear or coloured coating required?

Assuming 30min protection is required, Zeroflame Aquasteel WB+ 30min System for Steel is a popular choice.

Should you require clarification this will be suitable for your project we would require as much of the following information as possible;

• Level of fire protection required (i.e. 30, 60, 90min, etc.)
• Each steel section dimension (i.e. 254x146x37 UB)
• Quantity and length of each section (or overall meterage for each section)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Environment (internal, external, car park, chemical exposure, etc.)
• Application on site or in shop

Yes but these are only supplied upon request with a purchase of the fire stopping products and not separately.

We do not offer a clear fluid but we do have a coloured paint system that can be applied to certain types of wallpaper - Thermoguard Wallcoat BS Class 1/0 & EN Class B System.

When applying over wallpaper the 25m² pack size coverage should be reduced to 20m² and the 100m²  pack to 80m².

The majority of intumescent paints we offer are able to be spray applied, however in order for us to be able to advise which system to use we would require as much of the following information as possible;

• Level of fire protection required (i.e. 30, 60, 90min, etc.)
• Each steel section dimension (i.e. 254x146x37 UB)
• Quantity and length of each section (or overall meterage for each section)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Environment (internal, external, car park, chemical exposure, etc.)
• Application on site or in shop

Thermoguard Timbercoat BS Class 1/0 & EN Class B System

To be able to advise, we need as much of the following information as possible please;

• Size of surface area to paint
• Timber thickness
• Type of timber (i.e. pine, mdf, plywood, etc.)
• Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
• Internal or external
• Use (i.e. floor, wall cladding, ceiling, etc.)
• Bare or previously coated?

We do not supply anything meeting this description.

Can you advise what level of fire protection would satisfy your fire regulation requirements and building control please?

Thank you, please provide us with an image of the door(s) (if possible) and as much information as possible for the below points;

• Style of door? (i.e. panelled, ledge & brace, etc.)
• Solid or hollow core? - (please note we cannot provide anything to upgrade hollow doors)
• Door size? (height and width)
• Door thickness? (include thickness at thinnest point (i.e. panel))
• Number of doors to do?
• Clear or coloured finish required?
• Bare or previously painted?

Assuming the section has a wall thickness of at least 4mm, you would require 1 litre of Zeroflame Aquasteel WB+. If the steel is to remain visible in the property, this should be topcoated with Zeroflame Aquasteel WB+ Finish.

Thank you for your enquiry, in order for us to be able to advise, please provide us with as much of the following information as possible;

• Each steel section dimension (i.e. 254x146x37 UB)
• Quantity and length of each section (or overall meterage for each section)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Environment (internal, external, car park, chemical exposure, etc.)
• Application on site or in shop

Assuming 30min fire protection is required, Zeroflame Aquasteel WB+ 30min System for Steel is a popular choice.

Please contact our Technical Team on 0113 2455450 (option 2) to discuss your project.

Thank you for your enquiry, in order to be able to advise we would firstly need to know what level of fire protection your building control require you to achieve?

Also, what is the exposed area requiring protection - i.e. beams, underside of floorboards, columns, etc?

We would suggest looking at the Envirograf Door Upgrade Varnish System.

Providing the steel is in an internal environment and is already primed, we'd recommend our Zeroflame Aquasteel WB+ 30min System For Steel which includes a white intumescent coating and a coloured flame retardant topcoat.

Assuming a Class 1/0 level of protection is required, Hydron Nu-Flame Clear Impregnation can be applied to bare timber leaving it virtually unchanged aesthetically.

We currently have no products we could offer to achieve the new A1 or A2 fire classifications.

We'd recommend Thermoguard Timbercoat BS Class 1/0 & EN Class B System for application on to MDF to achieve a UK Class 1 finish.

You would need to seek advice from your authority as to the level of fire protection required and contact our Technical Team on 0113 2455450 (option 2) once this is known.

You can find our Door Upgrade Products HERE

To be able to advise you need to ask what level of fire protection would be required on your timber to deem it OK to not have to be removed. If you can provide us with this information we can then advise if we have a product that will acheive the required protection.

We would recommend you seek the advice of a qualified and reputable local log burner installer who may recommend either removal completely of the mantle or protecting by means of physical board or similar instead.

If it is deemed safe and you still wish to apply something as a precaution then you could choose any of our fire protection coatings for timber of your choice.

Assuming you require 30min protection for an internal, dry, heated environment we would suggest Zeroflame Aquasteel WB+ 30min System for Steel.

Hydron Nu-Flame Synthetic & Fabric Protector provides protection against fire for artwork and displays. We also have Thermoguard Flame Retardant Additive however, this is a special flame retardant agent to be added to conventional, single pack decorative, solvent or water based paints when used over a complete Thermoguard fire protection system for colour/finish change.

You haven't mentioned what level of fire protection you require, but assuming 30min protection is required (please check with your authority) then we would suggest Thermoguard Fire Varnish 30 & 60 Minute System.

Assuming this is a small domestic project and 30min protection is required we would Zeroflame Aquasteel WB+ 30min System for Steel which is available in any colour (including black) and comes in Eggshell or Gloss finishes.

Please see details of Envirograf Door Upgrade Varnish System. Download the 'Door Upgrading Technical Data' document from the 'Attachments' tab on the product page to check the suitability of your doors. Sikkens water based stains are suggested to be used if desired prior to application of the system.

Yes, assuming the plywood is bare we can offer a clear coating or a coloured coating system depending on your preference.

• Thermoguard Timbercoat BS Class 1/0 & EN Class B System
• Thermoguard Fire Varnish BS Class 1/0 & EN Class B System

Assuming the loft hatch is timber a minimum of 10mm thick and requires 30min protection we would suggest Thermoguard Timbercoat 30 & 60 Minute System.

We would need something further information here - i.e. is the plasterboard/wood in question around the fire itself (i.e. surround, mantle, etc.) or is it in other areas of the room? Also, what level of fire protection is your authority requesting these surfaces be brought up to? Please contact our Technical Team with the answers to these questions on 0113 2455450 (option 2).

We have two options to suggest as a starting point depending on what level of fire protection you wish to achieve;

• Thermoguard Timbercoat BS Class 1/0 & EN Class B System
• Thermoguard Timbercoat 30 & 60 Minute System

Most of our fire protection systems can come in the colour and finish of your choice, so black would be no issue for the system to come in for example meaning you would not have to worry about overcoating.

We have two options to suggest as a starting point depending on what level of fire protection you wish to achieve;

• Thermoguard Timbercoat BS Class 1/0 & EN Class B System
• Thermoguard Timbercoat 30 & 60 Minute System

We do not have any fire protection coatings that can be applied to glass.

All of the intumescent paints we offer for steel have their own range of topcoats that can be used to provide protection and colour to the steel once coated in intumescent paint. If you have a specific product in mind we can advise on the range of topcoats for that product.

Thank you for your enquiry, in order for us to be able to comment, please provide us with as much of the following information as possible;

• Size of surface area to paint
• Timber thickness
• Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
• Type of timber (i.e. pine, mdf, plywood, etc.)
• Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
• Internal or external
• Use (i.e. floor, wall cladding, ceiling, etc.)
• Clear or coloured coating required?
• Bare or previously coated?

Assuming a level of fire protection is required we would suggest Thermoguard Fire Varnish BS Class 1/0 & EN Class B System or Thermoguard Fire Varnish 30 & 60 Minute System - whichever satisfies the requirements of your authority.

We would recommend carrying out a sample area first to ensure you are happy with the appearance prior to coating the full area.

All the intumescent systems we offer for fire protection to steel are coloured and not clear.

Assuming BS Class 1/0 Surface Spread of Flame protection is required we would recommend Zeroflame Fire Retardant Paint. If this is not the level of fire protection required, please advise.

There is no charge for the issue of certification after use, however for us to be able to advise whether any of the products we offer would be suitable for your project we would require an image of the door(s) (if possible) and as much information as possible for the below points;

• Level of Fire Protection required? (i.e. 30min, 60min, etc.)
• Style of door? (i.e. panelled, ledge & brace, etc.)
• Solid or hollow core? - (please note we cannot provide anything to upgrade hollow doors)
• Door size? (height and width)
• Door thickness? (include thickness at thinnest point (i.e. panel))
• Number of doors to do?
• Clear or coloured finish required?
• Bare or previously painted?

See Envirograf Door Upgrade Paint System.

We do not offer any intumescent paints for steel that hold BBA certification due to them being unable to carry out fire testing. Instead they are reliant on fire test centres such as Exova, BRE etc. of which all the intumescent paints for steel we offer have been tested at such facilities and copies of certificates are freely available. 

In order for us to be able to advise which product would be best for your project, please provide us with as much of the following information as possible;

• Level of fire protection required (i.e. 30, 60, 90min, etc.)
• Each steel section dimension (i.e. 254x146x37 UB)
• Quantity and length of each section (or overall meterage for each section)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Environment (internal, external, car park, chemical exposure, etc.)
• Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Providing your doors are suitable then Envirograf Door Upgrade Paint System or Envirograf Door Upgrade Varnish System may be suitable.

We would suggest Envirograf 3-2-1 Standard Fire Retardant Liquid for this application. We would recommend the seller carries out their own due dilligence to ensure this will meet the requirements of their products/regulations.

Thank you for your enquiry, to be able to advise, please provide us with the following additional information;

• Timber thickness
• Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
• Type of timber (i.e. pine, mdf, plywood, etc.)
• Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
• Internal or external
• Use (i.e. floor, wall cladding, ceiling, etc.)
• Clear or coloured coating required?
• Bare or previously coated?

Assuming that it would not be subjected to moisture and 30 minutes is the level of protection required we would suggest Zeroflame Aquasteel WB+ 30min System for Steel.

Bullet Roof Mono achieved BROOF T4 fire rating.

Generally it is OK to box in steelwork with fire rated board instead of using an intumescent paint however in this instance it sounds as though there will be a combination of exposed steel and the fire board. We would advise discussing with your building inspector to check they are OK with the proposal before purchasing any paint.

Yes, our intumescent paint systems for steel are available in nearly all RAL and BS colours.

Unfortunately we do not have any intumescent paints that would achieve 1 hr on ductwork.

Certainly, please provide us with as much of the following information as possible;

• Level of fire protection required (i.e. 30, 60, 90min, etc.)
• Each steel section dimension (i.e. 254x146x37 UB)
• Quantity and length of each section (or overall meterage for each section)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Environment (internal, external, car park, chemical exposure, etc.)
• Application on site or in shop

We would suggest seeking approval from your authority for the Thermoguard Timbercoat Door Upgrade System.

Thank you for your enquiry, in order for us to be able to advise, please provide us with as much of the following information as possible;

• Level of fire protection required (i.e. 30, 60, 90min, etc.)
• Each steel section dimension (i.e. 254x146x37 UB)
• Quantity and length of each section (or overall meterage for each section)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Environment (internal, external, car park, chemical exposure, etc.)
• Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

For small, domestic projects we recommend all existing paint is removed apart from a suitable primer. After removal of existing coatings ensure all areas of steel are primed with a full coat of compatible primer and then apply the Zeroflame Aquasteel WB+ 30min System for Steel.

We do a number of clear intumescent coatings for wood but we would require as much of the following information as possible to be able to provide a recommendation on which one to use.

• Size of surface area to paint
• Timber thickness
• Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
• Type of timber (i.e. pine, mdf, plywood, etc.)
• Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
• Internal or external
• Use (i.e. floor, wall cladding, ceiling, etc.)
• Clear or coloured coating required?
• Bare or previously coated?

It would depend on the product being used. The application temperature range should be stated on the products Technical Data Sheet.

We're not sure what the size of 125ml relates to, however Zeroflame Aquasteel WB+ 30min System for Steel is a popular system we offer regularly for steel requiring 30 minutes fire protection.

If we are correct in assuming you are requiring a clear coating to apply over the emulsion to keep the look of what has been painted whilst upgrading the spread of flame rating, unfortuantely the clear coatings we offer would not be suitable for this. They are instead intended for bare timber or timber that has been previously stained or varnished.

Zeroflame Fire Retardant Paint wouldn't be suitable as it is only suitable for interior applications. If you can advise on the level of fire protection required we can recommend a suitable alternative.

The level of fire protection would need to be sought from your local authority to ensure compliance but we would assume as you have advised that the ceiling has 'fire-retardant boarding' that any requirement for separation/compartmentalisation had been achieved by this (i.e. 30min, 60min, etc.).

So assuming it is just a surface spread of flame concern for the outer facing plywood then we would suggest the exterior grade spec. of the Thermoguard Timbercoat BS Class 1/0 & EN Class B System.

Thank you for your enquiry, in order for us to be able to advise the best product, please provide us with as much of the following information as possible;

• Level of fire protection required (i.e. 30, 60, 90min, etc.)
• Each steel section dimension (i.e. 254x146x37 UB)
• Quantity and length of each section (or overall meterage for each section)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Environment (internal, external, car park, chemical exposure, etc.)
• Application on site or in shop

Unfortunately we currently have no products we can offer for this application

Unfortuantely not, 60 minutes fire protection would be the maximum we could offer with a paint product.

Most intumescent paints for steel can be applied over a standard (well applied) red oxide primer, however to provide confirmation of compatibility we would need a data sheet for the red oxide used.

Also, in order to provide a recommendation for the correct intumescent paint and quantity to use, please provide us with as much of the following information as possible;

• Level of fire protection required (i.e. 30, 60, 90min, etc.)
• Each steel section dimension (i.e. 254x146x37 UB)
• Quantity and length of each section (or overall meterage for each section)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Environment (internal, external, car park, chemical exposure, etc.)
• Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

We currently only offer heat resistant paints in aluminium, black and white.

Assuming the steels are already primed with a compatible primer, are internal and are not hollow sections, Zeroflame Aquasteel WB+ 30min System For Steel is a simple system to achieve 30mins fire protection.

Dependant upon the substrate you are looking to protect, the majority of our fire retardant products would be available in a minimum 1lt size but more information would be required - please email [email protected] with more information to enable us to provide further answers.

Assuming a UK Class 1/0 level of fire protection is required we can offer Thermoguard Fire Varnish BS Class 1/0 & EN Class B System for a clear finish or Thermoguard Timbercoat BS Class 1/0 & EN Class B System for a coloured finish. 

Zeroflame Fire Retardant Treatment can achieve UK Class 1/0 on timber decking boards but must be applied to a bare porous timber so the existing varnish would need to be removed. Once the treatment is fully dry, it can then be overcoated with a water based coating of your choice. We have no products/systems suitable for application over an existing varnish finish currently.

Assuming the timber is a bare softowood or hardwood and a UK Class 1/0 level of fire protection is adequate we'd recommend Zeroflame Fire Retardant Treatment.

Envirograf 3-2-1- Special Fire Retardant Liquid would be suitable for application on artificial flowers and foliage

Please see the link to our blog post on painting the walls around a fireplace or multi fuel stove - here

Unfortunately we wouldn't have anything we could offer for this application currently.

Unfortunately we wouldn't have any products we could recommend for direct heat contact.

Thermoguard Timbercoat BS Class 1/0 & EN Class B System can be applied over existing painted timber to achieve a Class 1/0 level of fire protection.

Assuming a UK Class 1/0 level of fire protection is required, Zeroflame Fire Retardant Treatment can be applied to bare softwood and hardwood timber - once dry, this can be overcoated with a water based stain of your choice.

If you are looking to paint the walls within a stairwell and a UK Class 1/0 level of fire protection is required, we'd recommend Thermoguard Wallcoat BS Class 1/0 & EN Class B System.

Hydron Nu-Flame Synthetic & Fabric Protector can be applied to curtains to achieve BS 5867 Part2 Type B & BS 5852 0 & 1. Following purchase and application a certificate can be obtained.

Every individual steel section size would need a different loading to achieve the same level of fire protection. The number of sides exposed, the orientation and the environment would all have an impact on the product we would recommend and the loading requirements.

Unfortunately we currently have no fire retardant coatings suitable to receive any kind of traffic I'm afraid.

We currently have no products we could offer to fire resistance on glass.

Thank you for your enquiry, in order to enable us to provide a recommendation and price please provide us with as much of the following information as possible;

• Level of fire protection required (i.e. 30, 60, 90min, etc.)
• Each steel section dimension (i.e. 254x146x37 UB)
• Quantity and length of each section (or overall meterage for each section)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Environment (internal, external, car park, chemical exposure, etc.)
• Application on site or in shop

We have a range of products for doors, see here: https://www.rawlinspaints.com/door-upgrade-kits

Please provide us with an image of the door(s) (if possible) and as much information as possible for the below points;

• Level of Fire Protection required? (i.e. 30min, 60min, etc.)
• Style of door? (i.e. panelled, ledge & brace, etc.)
• Solid or hollow core? - (please note we cannot provide anything to upgrade hollow doors)
• Door size? (height and width)
• Door thickness? (include thickness at thinnest point (i.e. panel))
• Number of doors to do?
• Clear or coloured finish required?
• Bare or previously painted?

To ensure you are purchasing and applying sufficient material you must measure your door surface areas to get to a total square metre area to coat and then buy sufficient Envirograf Door Upgrade Paint System.

If you would like us to help, please provide our Technical Department ([email protected]) with an image of the door(s) (if possible) and as much information as possible for the below points;

• Level of Fire Protection required? (i.e. 30min, 60min, etc.)
• Style of door? (i.e. panelled, ledge & brace, etc.)
• Solid or hollow core? - (please note we cannot provide anything to upgrade hollow doors)
• Door size? (height and width)
• Door thickness? (include thickness at thinnest point (i.e. panel))
• Number of doors to do?
• Clear or coloured finish required?
• Bare or previously painted?

Please contact our Technical Team on 0113 2455450 (option 2)

Thank you for your enquiry, in order to enable us to provide a recommendation and price please provide us with as much of the following information as possible;

• Level of fire protection required (i.e. 30, 60, 90min, etc.)
• Each steel section dimension (i.e. 254x146x37 UB)
• Quantity and length of each section (or overall meterage for each section)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Environment (internal, external, car park, chemical exposure, etc.)
• Application on site or in shop

For Interior applications we would suggest - Envirograf QVFR Clear Class 1/0 & EN Class B System for Wood (Interior) and for exterior Envirograf ES/VFR Clear Class 1/0 & EN Class B System for Wood (Exterior)

Unfortunately we couldn't offer anything in clear to go over a previously painted surface but assuming a UK Class 1/0 level of protection is suitable then we'd recommend Thermoguard Timbercoat BS Class 1/0 & EN Class B System for a coloured paint system.

We would recommend Envirograf QVFR Clear Class 1/0 & EN Class B System for Wood (Interior) for area requiring EN class B s1 d0. For areas requiring 30 minute fire protection we would recommend the following:

• 1 coat of Envirograf HWAP/WB Primer @ 10m² per litre
• 2 coats of Envirograf HW02N Clear Intumescent Coating @ 8m² per litre/per coat
• 1 coats of Envirograf HW Excel Clear Top Coat (Matt, Satin or Gloss) @ 10m² per litre

Please note minimum timber thicknesses apply and we recommend you refer this information to your authority for approval and ask them to satisfy themselves with the information provided by the manufacturer for each product (Data Sheets, Test Data, etc.) prior to purchase and application.

No, however we are able to provide intumescent paint systems for steel in nearly any colour. Please contact our Technical team for further details on 0113 2455450 (option 2) or [email protected]

Thank you for your enquiry, please provide us with an image of the door(s) (if possible) and as much information as possible for the below points;

- Level of Fire Protection required? (i.e. 30min, 60min, etc.)

- Style of door? (i.e. panelled, ledge & brace, etc.)

- Solid or hollow core? - (please note we cannot provide anything to upgrade hollow doors)

- Door size? (height and width)

- Door thickness? (include thickness at thinnest point (i.e. panel))

- Number of doors to do?

- Clear or coloured finish required?

- Bare or previously painted?

Please submit requested information to [email protected] and we can assist with the specification

Unfortunately there is not currently a fire retardant paint you can use on polystyrene tiles.

Unfortunately we cannot offer any Fire Protection paint for a steel door.

If you are looking to achieve Class 0 Fire Protection we can recommend Thermoguard Fire Varnish Sprayshop Lacquer System

This is only available in a satin or gloss finish.

You can certainly coat the steelwork with intumescent paint to provide the level of fire protection you require but you cannot then plaster over it. It would need to remain as the intumescent paint and topcoat only.

If you wish to proceed, please provide us with as much of the following information as possible;

• Level of fire protection required (i.e. 30, 60, 90min, etc.)
• Each steel section dimension (i.e. 254x146x37 UB)
• Quantity and length of each section (or overall meterage for each section)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Environment (internal, external, car park, chemical exposure, etc.)
• Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Presuming you require some level of fire protection we would suggest starting by looking at Thermoguard Timbercoat 30 & 60 Minute System

No, if you wish to keep the coloured paint appearance you would need to use a paint systema and not a clear varnish. In order for us to be able to advise which product/system would be best for your doors, please provide us with an image of the door(s) (if possible) and as much information as possible for the below points;

• Level of Fire Protection required? (i.e. 30min, 60min, etc.)
• Style of door? (i.e. panelled, ledge & brace, etc.)
• Solid or hollow core? - (please note we cannot provide anything to upgrade hollow doors)
• Door size? (height and width)
• Door thickness? (include thickness at thinnest point (i.e. panel))
• Number of doors to do?
• Clear or coloured finish required?
• Bare or previously painted?

Assuming the application is on an interior concrete floor we would recommend Thermoguard Flame Retardant Floor Paint.

For this application we can recommend Firetherm Intusil

Thank you for your enquiry, in order for us to be able to advise, please provide us with as much of the following information as possible;

• Level of fire protection required (i.e. 30, 60, 90min, etc.)
• Each steel section dimension (i.e. 254x146x37 UB)
• Quantity and length of each section (or overall meterage for each section)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Environment (internal, external, car park, chemical exposure, etc.)
• Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

As long as the gap between the cable and the plasterboard is no bigger than 10mm you could use Protecta FR Putty Cord or if the gap is between 10-30mm you can use Protecta FR Acrylic 4hr Intumescent Sealant, both will give at least 60min integrity and insulation.

We would consider Thermoguard Wallcoat 30 & 60 Minute System for this type of application but would first need some further information to confirm suitability. Please contact our Technical Department on 0113 2455450 (option 2).

Yes, we offer compatible topcoats that are available in a wide range of colours, see Zeroflame Aquasteel WB+ 30min System for Steel or Zeroflame Aquasteel WB+ 60min System for Steel.

Assuming the steel is already suitably primed, 30min protection is required and all is internal, we would recommend Zeroflame Aquasteel WB+ 30min System for Steel. This kit provides the intumescent basecoat and topcoat in Eggshell or Gloss finish in any colour of your choice.

You cannot buy an intumescent paint and then apply your own topcoats. Delivery to Bath would be as follows;

3 - 5 days FREE, 2 - 3 days £8.00 + VAT, next working day £15.00 + VAT.

Please call our Technical Team on 0113 2455450 (option 2) to discuss with one of our experts due to the complexity of the enquiry.

Assuming it is for interior use, Envirograf QVFR Clear Fire Protection Coating is suitable for upgrading new and already coated timber and wood related surfaces to BS Class 0 & 1 and EU standard B/s1/d0 and is available in Matt, Satin or Gloss finish. Please refer to data sheets before use (available to download from the 'Attachments' tab) and contact our Technical Team on 0113 2455450 (option 2) if in doubt.

Thermoguard Timbercoat 30 & 60 Minute System is a popular choice, however for 60min protection we would recommend you speaking to our Technical Team before purchase/use on 0113 2455450 (option 2).

Thank you for your enquiry, in order to be able to advise a suitable system, please provide us with as much of the following information as possible;

• Size of surface area to paint
• Timber thickness
• Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)Type of timber (i.e. pine, mdf, plywood, etc.)
• Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
• Use (i.e. floor, wall cladding, ceiling, etc.)
• Clear or coloured coating required?
• Bare or previously coated?

Thank you for your enquiry, assuming the beam is steel, in order for us to be able to advise, please provide us with as much of the following information as possible;

• Level of fire protection required (i.e. 30, 60, 90min, etc.)
• Each steel section dimension (i.e. 254x146x37 UB)
• Quantity and length of each section (or overall meterage for each section)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Environment (internal, external, car park, chemical exposure, etc.)
• Application on site or in shop

For this application we can recommend Hydron Nu-Flame Synthetic & Fabric Protector.

This achieves BS 5867 Part2 Type B & BS 5852 0 & 1. Easy to apply, and can be dry cleaned up to 10 times.

We stock a range of Fire Barrier Curtains to create a fire barrier between perimeter fixings, such as above suspended ceilings and between soffits, or wrap around trusses and beams for a protective fireproof barrier in domestic, commercial and industrial properties. 

Alternatively, if you are wishing to improve the flame retardancy of your materials, see our range of Fire Retardant Liquids.

Thank you for your enquiry, in order for us to be able to advise, please provide us with as much of the following information as possible;

• Each steel section dimension (i.e. 254x146x37 UB)
• Quantity and length of each section (or overall meterage for each section)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Environment (internal, external, car park, chemical exposure, etc.)
• Application on site or in shop

We would need to know a specific product to be able to advise. You can contact our Technical Team on 0113 2455450 (option 2) to discuss.

Class 0/1 is not an equivalent to 30 minutes fire resistance. We would need clarification on exactly what level of fire protection was required by your authority and then answers to the following questions to be able to advise on a suitable product/system;

• Size of surface area to paint
• Timber thickness
• Type of cladding (i.e. T&G, feather edge / shiplap, etc.)
• Internal or external
• Clear or coloured coating required?

Our Technical Team can be contacted on 0113 2455450 (option 2) or [email protected]

This would depend on a number of factors, please contact our Technical Team on 0113 2455450 (option 2) to discuss.

None of the fire protection products we offer clear or otherwise have BBA certification due to BBA being unable to carry out fire testing. Instead they are reliant on fire test centres such as Exova, BRE, etc. of which the products we offer are tested to hold third party approval certificates from these relevant test centres.

We stock many options for Fire Protection including Thermoguard Timbercoat Door Upgrade System.

If you would like further assistance regarding Fire Protection please contact our Technical team on 0113 2455450 option 2 who can provide you with a specification for the project.

See Zeroflame Aquasteel WB+ 30min System for Steel which is available in this colour.

Assuming the timber is bare, you are looking for Class 0 Level of Fire Potection and the timber meets the requirements in Technical Data Sheet you could consider Zeroflame Fire Retardant Treatment.

The Technical Data Sheet is in the attachment tab on the product page.

For a specification to the project requirements please contact our Technical team on 0113 2455450 option 2.

To assist you with this enquiry we will require more information on the products and the method used to attach them.

Please contact our Technical team on 0113 2455450 option 2.

Thank you for your enquiry, to enable us to be able to advise please provide us with as much of the following information as possible;

• Each steel section dimension (i.e. 254x146x37 UB)
• Quantity and length of each section (or overall meterage for each section)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

To assist you with a Fire Protection specification please contact our Technical team on 0113 2545450 option 2.

Zeroflame Fire Retardant Treatment could be applied to bare timber areas, this would help increase fire protection properties of the timber.

We would ask you to consult the documentation with the chimenea regarding proximity during operation.

If these doors have been purchased as fire doors then we would recommend Envirograf HW Excel Clear Top Coat as this is flame retardant.

The intumescent paints are white in colour, but flame retardant topcoats are suitable for application over the corresponding intumescent paint and are available in many Ral and BS colour options.

In order for us to be able to provide advice on the most suitable products for your project,  please provide us with as much of the following information as possible;

• Size of surface area to paint
• Timber thickness
• Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
• Type of timber (i.e. pine, mdf, plywood, etc.)
• Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
• Use (i.e. floor, wall cladding, ceiling, etc.)
• Clear or coloured coating required?
• Bare or previously coated?

We would instead suggest Zeroflame Aquasteel WB+

Hollow sections for 30min protection need to be a minimum wall thickness of 4mm.

Download the product data sheet from the attachments tab for advice on preparation of the steel and topcoating.

Assuming the steel is internal, we would suggest considering Zeroflame Aquasteel WB+ 60min System for Steel.

We would suggest viewing Zeroflame Aquasteel WB+ 30min System for Steel

If in any doubt, please contact our Technical Team on 0113 2455450 (option 2) and we can assist you with a specification.

Assuming the timber is bare, meets the requirements in the Technical Data Sheet and you are looking for a Class 0 level of Fire Protection we can recommend Zeroflame Fire Retardant Treatment.

For assistance with Fire Protection please call our Technical team on 0113 2455450 option 2.

We do not supply fire doors but if building control approve the application of a 30minute fire protection paint to the current door, we can assist you with a specification and recommend a product.

Please contact our Technical team on 0113 2455450 option 2 for more information.

Thank you for your enquiry, in order for us to be able to advise, please provide us with as much of the following information as possible;

• Each steel section dimension (i.e. 254x146x37 UB)
• Quantity and length of each section (or overall meterage for each section)
• Orientation (horizontal or vertical)
• Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
• Environment (internal, external, car park, chemical exposure, etc.)
• Application on site or in shop

If in any doubt, please contact our Technical Team on 0113 2455450 (option 2).

See Zeroflame Aquasteel WB+ 30min System for Steel

If in any doubt, contact out Technical team on 0113 2455450 (option 2).

Unfortunately we do not have a product we can recommend for this application to polystyrene tiles.

Depending on the level of Fire Protection you require we have many options to protect timber, steel and plasterboard.

Please confirm with Building Control the level of Fire Protection you require prior to ordering.

We can then recommend Zeroflame Aquasteel 30 and 60 minute systems.

We stock Fire Protection coatings for many different applications and substrates inlcuding Steel and Timber. In order to ascertain what level of protection you need on any of your areas you should refer to your authority on the project which is often your local Building Control.

Depending on the level of Fire Protection you require for the steel, one of the Zeroflame Aquasteel Systems may be suitable for you.

For the timber ceiling joists we would need to know the following to be able to advise;

• Size of section (width and height)
• Length of section
• Number of sections
• Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
• Type of timber (i.e. pine, oak, CLT, etc.)
• Clear or coloured coating required?
• Bare or previously coated?

Our Technical Team can be contacted on 0113 2455450 (option 2) or [email protected] to assist with a specification.

You would need to refer to your authority on this project to ascertain the level of fire protection required. If it is 30min protection required we could recommend Thermoguard Timbercoat 30 & 60 Minute System.

Assuming you are looking to achieve Class 0 Level of Fire Protection and the fence has not been previously painted and meets the substrate requirements in the Technical Data Sheet we can recommend Zeroflame Fire Retardant Treatment.

This product is clear, lasts for the lifetime of the substrate once absorbed and can be over painted for decorative purposes - Waterborne stains or varnishes can be used over Zeroflame Fire Retardant Treatment as long as they are compatible, non-flammable and will dry. We always recommend to try a small sample area first to ensure the stain does not react with the Zeroflame Fire Retardant Treatment and will dry out.

No.

Without knowing what system has already been applied we could only recommend that the whole system be removed and a new fire retardant system applied. If Class 1/0 is required then we'd recommend Thermoguard Timbercoat BS Class 1/0 System. For 30mins protection we'd recommend Timbercoat 30 & 60 minute system but this would only be suitable if your timber meets the required minimum thickness.

If Class 1/0 is required then we'd recommend Thermoguard Fire Varnish BS Class 1/0 & EN Class B System. For 30mins protection we'd recommend Thermoguard Fire Varnish 30 & 60 Minute System but this would only be suitable if your timber meets the required minimum thickness.

Assuming you seek approval from building control prior to application, the timber is bare and the level protection specified is Class 0, Zeroflame Fire Retardant Treatment would be suitable.

Yes, Zeroflame Fire Retardant Paint can be applied over sound existing coatings such as Zinsser B-I-N.

Assuming the timber is bare and meets the requirements specified in the Technical Data Sheet we can recommend Zeroflame Fire Retardant Treatment. Once fully dry this can be overcoated with any waterbased paint to achieve the desired finish.

Assuming the timber is bare and you are looking for Class 0 level of Fire Protection and approval is sought from Building Control, we can recommend Zeroflame Fire Retardant Treatment. This lasts for the lifetime of the substrate and can be over painted with a compatable waterbased paint once fully dry.

We do not currently have a product available to meet a Class A2 rating.

Nullifire SC802 On-Site Water-Based Intumescent Basecoat is supplied ready for use. It must not be thinned but mechanically stirred prior to use.

Assuming the substrates are absorbent we can recommend Envirograf 3-2-1 Standard Fire Retardant Liquid. This can be applied to polyurethane furniture and timber.

Bullet Roof Mono achieved BROOF T4 fire rating. Highest available in Europe. This waterproofing system can be applied to many flat roof substrates.

Assuming the doors meet the minimum requirements to be protected as detailed in the Technical Data Sheet and you are looking for 30 minutes Level of Fire Protection, we can recommend the Envirograf Door Upgrade Paint System. Please check suitability with building control prior to application.

To assist you with specifying Fire Protection Coatings please contact our Technical Team on 01132545450 option 2.

Assuming the doors meet the minumum requirements and you are looking for 30minutes Fire Protection we can recommend Envirograf Door Upgrade Varnish System. Please confirm suitabliity with Building Control prior to application.

Unfortunately we do not have a fire protection product to recommend for this application to a french polished timber.

Unfortunately we do not have a fire protection option we can recommend for application to oiled timber.

We would recommend consulting building control to ascertain which elements of the structure they wish to be protected and to what level.

Thank you for the enquiry, we have contacting you directly for more information.

Thank you for your enquiry, please provide us with an image of the door(s) (if possible) and as much information as possible for the below points to [email protected]

- Level of Fire Protection required? (i.e. 30min, 60min, etc.)
- Style of door? (i.e. panelled, ledge & brace, etc.)
- Solid or hollow core? - (please note we cannot provide anything to upgrade hollow doors)
- Door size? (height and width)
- Door thickness? (include thickness at thinnest point (i.e. panel))
- Number of doors to do?
- Clear or coloured finish required?
- Bare or previously painted?

Thank you for the enquiry, to assist with this enquiry we will require some more information please.

What level of fire protection do building control require you to achieve?

Are the ceilings and walls lathe and plaster, plasterboard or another substrate?

If plasterboard how thick is it?

We do have fire protection products for painting timber to differing levels of fire protection.

As to if the ceiling requires fire protection and to what level we could not advise on, we would recommend consulting building control on this matter.

Assuming no level of fire protection is required, the previously varnished timber is clean, dry, sound and prepard as detailed in the technical data sheet we can recommend Zinsser B-I-N followed by Zinsser Perma-White Interior.

This is available in many RAL and BS colours in a matt or satin finish.

This is a scrubbable paint suitable for high humidity areas, but does not provide a level of fire protection

Assuming a level of fire protection is required on the universal steel, we can recommend the Thermoguard Thermocoat WI System's for Universal Beams & Columns.

These systems come in m² pack sizes for 30 or 60mins protection and the topcoats can be mixed to many RAL or BS colours.

We would recommend seeking approval from Building Control prior to application.

If you require assistance with a specification please contact [email protected]

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Thank you for the enquiry, unfortunately we do not have a product to recomemnd to upgrade lathe and plaster areas.

For the plasterboard areas, assuming it is over 9mm thick and building control approve its use for your application Thermoguard Wallcoat 30 & 60 Minute System for Plasterboard could be used.

To assist with a specification for the doors we will require more informaotion, please can you send the information below to [email protected] 

- Level of Fire Protection required? (i.e. 30min, 60min, etc.)
- Style of door? (i.e. panelled, ledge & brace, etc.)
- Solid or hollow core? - (please note we cannot provide anything to upgrade hollow doors)
- Door size? (height and width)
- Door thickness? (include thickness at thinnest point (i.e. panel))
- Number of doors to do?
- Clear or coloured finish required?
- Bare or previously painted?

Thank you for the enquiry, we will need the information below to assist with this enquiry. Please send the information to [email protected]

- Level of fire protection required (i.e. 30, 60, 90min, etc.)
- Each steel section dimension (i.e. 254x146x37 UB)
- Quantity and length of each section (or overall meterage for each section)
- Orientation (horizontal or vertical)
- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)
- Building type (i.e. office, domestic, storage, etc.)
- Environment (internal, external, car park, chemical exposure, etc.)
- Application on site or in shop
Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

To apply for certification please follow the link on the product page Thermoguard Thermocoat W. If you are looking to change the finished colour we recommend using Thermoguard Flame Retardant Topcoat.

Assuming the doors meet the minimum requirements as detailed in the Technical Data Sheet we can recommend the Envirograf Door Upgrade Varnish System and Envirograf Surface Mounted Intumescent Fire & Smoke Seals.

Please seek approval from Building Control prior to application.

Assuming the doors meet the requirements detailed in the Technical Data sheet and approval from Building Control is sought prior to application, we can recommend the Envirograf Door Upgrade Systems.

These are available in 4, 10 and 20m² packs or we can provided a tailored specification if you contact our Technical team on 01132455450 option 2.

These systems can be applied by brush, roller or airless spray.

You can apply the systems to previously painted doors, we advise to test on a small area for compatability prior to full application and a clear coating is not recommend over an previously painted finish.

Most of the stocked Fire Protection systems are available with a coloured flame Retardant Topcoat. These are available in many RAL and BS colours but we do not have colour samples available.

Depending on the Level of Fire Protection you need to achieve we can recommend the Envirograf EP/CP Fire Protection Coating. Please confirm level of fire protection required with building control and seek their approval prior to application. 

This is a white fire protection coating for plasterboard and lath-&-plaster ceilings.

Assuming the walls are clean, dry, sound and approval is sought from Building Control prior to application we can recommend Thermoguard Wallcoat 30 & 60 Minute System.

Please contact our Technical Team for a specificaton on 0113 2455450 option 2. Most Fire Protection systems are available with a flame retardant topcoat in many RAL and BS colours.

Unfortunately without knowing the intumescent paint that has been used and the chemicals the coating would be exposed to we wouldn’t be able to recommend anything for your application.

Assuming the doors meet the minimum requirements detailed in the Technical Data Sheet and approval is sought from Building Control prior to application we can recommend Envirograf Door Upgrade Systems.

Assuming the substrate is porous we can recommend Bollom Flamebar PE6.

Assuming the doors are clean,dry and sound we can recommend using a Class 0 system as painting with a solvent based paint could increase the fire risk.

For this application Bollom Flameguard Ultra Primer / Undercoat and Bollom Flameguard Ultra Gloss would be ideal.

This is available in many RAL and BS colours.

Assuming the substrate meets the requirements stated in the Technical Data Sheet and approval is sought from building control prior to application we can recommend Thermoguard Wallcoat 30 & 60 Minute System.

Assuming the doors are clean, dry and sound we can recommend Bollom Flameguard Ultra Primer / Undercoat followed by one of the Bollom Flameguard ultra topcoats.

They are applied as part of a system, with Thermoguard Wallcoat first, followed by Thermoguard Wallcoat Smoke & Flame Retardant Topcoat. The number of coats of Thermoguard Wallcoat is determined by the level of protection you are aiming to achieve.

Unfortunately we do not have a product to recommend for this application.

Unfortunately we do not have a product to recommend for this application.

Please see our blog post on Painting the Walls Around a Fireplace or Multi-Fuel Stove for information and recommendations for this application.

Please see our blog post on Painting the Walls Around a Fireplace or Multi-Fuel Stove for assistance with this enquiry.

Unfortunately we do not have a product to recommend for this application.

Assuming the plywood board is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zeroflame Fire Retardant Paint.

This will achieve Class 0, is available in white and can be over painted with waterbased paints.

Unfortunately we do not have a product to recommend for this application.

Assuming this is for the internal walls and a Class 1/0 level of fire protection is required, we'd recommend Thermoguard Wallcoat BS Class 1/0 & EN Class B System for your application. An extra coat of the topcoat would be beneficial should the areas be wiped down etc.

Assuming the timber is bare, clean, dry and sound we can recommend Zeroflame Fire Retardant Treatment.

This is a clear product and lasts for the lifetime of the substrate.

The coverage rate on standard timber is 3.7m² per 1ltr, so a 5ltr will cover 18.5m²

Unfortunately we do not have a product to recommend for this application.

Thank you for the enquiry, we have contacted you directly by email.

Please see our blog post Painting the walls around a fireplace or multi fuel stove.

Please see our blog post Painting the walls around a fireplace or multi fuel stove.

Thank you for the enquiry, unfortunately we do not have a clear intumescent product for steel, we have contacted you directly by email to see if we can assist you.

An email has been sent to you requesting further information for this enquiry.

The recommended compatible topcoat for Zeroflame Aquasteel WB+ is Zeroflame Aquasteel WB+ Finish which is available in RAL and BS colours and either an Eggshell or Gloss finish.

We have contacted you by email for more information regarding this enquiry.

This would be dependant on the products purchased and applied, please send an email to [email protected] with your request.

Thank you for the enquiry, we have contacted you directly for more information.

Thank you for the enquiry, we have contacted you directly for more information.

Thank you for the enquiry, we have contacted you directly for more information.

Thank you for the enquiry, we have contacted you directly for more information.

Thank you for the enquiry, we have contacted you directly for more information.

Assuming you are looking for a Class 0 level of Fire Protection, the timber is clean, dry, sound and prepared as detailed in the Technical Data Sheet then Thermoguard Timbercoat BS Class 1/0 & EN Class B External System could be used.

Thank you for the enquiry, we have contacted you directly for more information.

Thank you for the enquiry, we have contacted you directly for more information.

Yes Thermoguard Wallcoat and Thermoguard Wallcoat Smoke & Flame Retardant Topcoat can be sprayed by conventional spray or airless if the equipment has the required specification.

Zeroflame Fire Retardant Treatment would not be suitable for this application due to mill glazing sealing the pores of the timber.

Thermoguard Fire Varnish BS Class 1/0 & EN Class B System could be used to achieve a class 0 level of fire protection assuming the timber is throughly dry and abraded prior to application.

Hydron Nu-Flame Synthetic & Fabric Protector is suitable for application on artifical flowers and foliage and is available in a 5lt tub. This can be decanted down in to a standard spray bottle should you wish.

Assuming you have had a specification for the steels, please see the link  to 2.5kg of Thermoguard Thermocoat WI Ultimate and the Thermoguard Flame Retardant Topcoat.

If you would like assistance with a specification please contact our Technical Team on 0113 245 54550 option 2.

Thank you for the enquiry, unfortunately we do not have a product we can recommend for this application.

Thank you for the enquiry, we have contacted you directly for more information.

Assuming the plaster board in a minimum of 9mm thick, the wall is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Thermoguard Wallcoat 30 & 60 Minute System for Plasterboard to achieve 30mins fire protection.

Approval should be sought from Building Control prior to application for suitability for the project.

Thank you for the enquiry, we have contacted you directly for more information to assist with a specification.

Thank you for the enquiry, we have contacted you directly for more information to assist you.

Thank you for the enquiry, we have contacted you directly for more information to assist you with a recommendation.

Thank you for the enquiry, we have contacted you directly for more information to assist you with a recommendation.

Thank you for the enquiry, unfortunately we do not have a product we can recommend for application to lathe and plaster to meet this level of fire protection.

Thank you for the enquiry, we have contacted you directly for more information.

Thank you for the enquiry we have contacted you directly for more information.

Thank you for the enquiry, we have contacted you directly for more information.

Assuming you require Class 0 level of fire protection, the timber is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zeroflame Fire Retardant Treatment.

For 20m² you would require 2 x 5ltr.

Thank you for the enquiry, we have contacted you directly for more information.

Thank you for the enquiry, we have contacted you directly for more information. Any competent person can apply these varnishes, after application you can apply for certification.

Unfortunately the maximum level of fire protection we could offer on OSB is class 0.

If your building control officer approves it for your application, the osb is clean, dry, sound and prepared as detailed in the technical data sheet Thermoguard Safewood Anti-Viral Fire Protection System could be used.

Thank you for the enquiry, we have contacted you directly for more information to assist you with a recommendation.

Thank you for the enquiry, we have contacted you directly for more information.

Thank you for the enquiry we have contacted you directly for more information.

Thank you for the enquiry, we have contacted you directly for more information.

Unfortunately we currently do not offer any clear fire retardant coatings for metal.

Thank you for the enquiry, we have contacted you directly for more information.

Zeroflame Fire Retardant Treatment can be applied to bare solid softwoods and hardwoods leaving the appearance of the timber virtually unchanged. It will achieve a UK Class 0 or Euro Class B providing the timber isn;t man made such as OSB or plywood.

Thank you for the enquiry, unfortunately there is not a clear intumescent paint for steel that we are aware of.

To remove Jotun Steelmaster 600WF you would have to abrade or blast it off.

Thank you for the enquiry, we have contacted you for more information.

Thank you for the enquiry, we have contacted you directly for more information.

Intumescent paint systems can be applied to galvanised steel, but not cold rolled steel.

Unfortunately these angles will not be possible to protect.

Unfortunately we do not have a wood preserver treatment that is fire retardant, but we do have fire protection coatings that have a stained finish.

We have contacted you directly for more information.

Most steel fire protection coatings must be applied to a clean, dry, prepared substrate primed with a compatible primer.

Thank you for the enquiry, we have contacted you directly for more information.

After application of a Bollom system you can apply for certification using the link here.

If you require assistance with a specification for the steel, please send the information below to [email protected].

- Level of fire protection required (i.e. 30, 60, 90min, etc.)
- Each steel section dimension (i.e. 254x146x37 UB)
- Quantity and length of each section (or overall meterage for each section)
- Orientation (horizontal or vertical)
- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)
- Building type (i.e. office, domestic, storage, etc.)
- Environment (internal, external, car park, chemical exposure, etc.)
- Application on site or in shop"

Thank you for the enquiry, unfortunately oiled timber is not suitable to have a fire protection coating applied to.

The other doors must meet minium requirements to be suitable to be upgraded, please provide the information below with photos of the doors to [email protected]

- Level of Fire Protection required? (i.e. 30min, 60min, etc.)
- Style of door? (i.e. panelled, ledge & brace, etc.)
- Solid or hollow core? - (please note we cannot provide anything to upgrade hollow doors)
- Door size? (height and width)
- Door thickness? (include thickness at thinnest point (i.e. panel))
- Number of doors to do?
- Clear or coloured finish required?
- Bare or previously painted?

Thank you for the enqiury, to assist with this enquiry please send the information requested below to [email protected]

GENERAL TIMBER SURFACES
- Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

Thank you for the enquiry, it is unusual for metal railing to require fire protection, unfortunatley we do not have a product to recommend for this application.

No, unfortunately we do not have a fire protection product to recommend for application to plastic.

Thank you for the enquiry, we will need the information below to assist with a specification for these steels, please send the information to [email protected]. 

• Level of fire protection required (i.e. 30, 60, 90min, etc.)
  - Each steel section dimension (i.e. 254x146x37 UB)
  - Quantity and length of each section (or overall meterage for each section)
  - Orientation (horizontal or vertical)
  - Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
  - Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)
  - Building type (i.e. office, domestic, storage, etc.)
  - Environment (internal, external, car park, chemical exposure, etc.)
  - Application on site or in shop
• 
  Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

We can supply paint systems to achieve 30 or 60mins protection to timbers that meet the minimum substrate requirements.

We would recommend seeking approval from building control prior to application.

Please email the information below to [email protected] and we can see if they are suitable to be upgraded.

GENERAL TIMBER SURFACES
- Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

Thank you for the enqiury, we will require more information to assist with specification to fire protect timber, please send the information below to [email protected]

GENERAL TIMBER SURFACES
- Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

Unfortunately Thermoguard Thermocoat products are not suitable for application by HVLP, but they can be applied by brush or roller or commercial airless spray equipment.

If the steel has anything other than a compatible primer on, it must be stripped back to bare metal before application of a compatible primer then the Thermocoat system.

In this case you will need to apply Thermoguard Steel Fire Paint Primer once you have stripped the steel back to a bare, sound condition.

Assuming the primer on the steels is compatible, the steels are clean, dry, sound and prepared as detailed in the technical data sheet a Bollom Brosteel Ultra 60min System could be used.

These are sold in m² pack sizes and the topcoats can be mixed to many RAL and BS colours in a gloss, eggshell or matt finish.

We would recommend seeking approval from your building control officer prior to application.

Please complete the Bollom Steelwork Form, this can be found on the Bollom Brosteel Ultra 60 product page and e-mail this to [email protected] so that we offer the most suitable product.

You will need to submit and application for certification to Thermoguard.

This can be done following the link below.

THERMOGUARD FIRE CERTIFICATE APPLICATION

No, BD 2569 asks for a material of limited combustibility.

This is any material which, when tested to the European Classification in accordance with BS EN 13501 Part 1,
achieves a minimum classification of A2-s3,’

Unfortunatley we do not have a product that can meet this level of fire protection.

We will require more information to assist with this enquiry, please send the information below to [email protected]

GENERAL TIMBER SURFACES
- Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

Yes, we do have products that can be used for this application, we will need the information below to assist with a specification.

Please answer the questions and send to [email protected]

- Level of fire protection required (i.e. 30, 60, 90min, etc.)
- Each steel section dimension (i.e. 254x146x37 UB)
- Quantity and length of each section (or overall meterage for each section)
- Orientation (horizontal or vertical)
- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)
- Building type (i.e. office, domestic, storage, etc.)
- Environment (internal, external, car park, chemical exposure, etc.)
- Application on site or in shop
Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Thank you for the enquiry, unfortunately there is not clear intumescent paint we can supply for steel.

Assuming a painted finish is acceptable please provide the information below to [email protected].

- Level of fire protection required (i.e. 30, 60, 90min, etc.)
- Each steel section dimension (i.e. 254x146x37 UB)
- Quantity and length of each section (or overall meterage for each section)
- Orientation (horizontal or vertical)
- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)
- Building type (i.e. office, domestic, storage, etc.)
- Environment (internal, external, car park, chemical exposure, etc.)
- Application on site or in shop
Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Thank you for the enqiury, to assist further we will need the information below sending to [email protected]

GENERAL TIMBER SURFACES
- Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

Thank you for the enquiry, we would need more information to assist with this enquiry, please answer the questions below and email to [email protected]

GENERAL TIMBER SURFACES
- Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

In many cases intumescent coatings cannot be repaired and the steel section will need to be stripped and a new system specified and applied.

Please send the information below to [email protected]

- Level of fire protection required (i.e. 30, 60, 90min, etc.)
- Each steel section dimension (i.e. 254x146x37 UB)
- Quantity and length of each section (or overall meterage for each section)
- Orientation (horizontal or vertical)
- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)
- Building type (i.e. office, domestic, storage, etc.)
- Environment (internal, external, car park, chemical exposure, etc.)
- Application on site or in shop
Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Thank you for the enquiry, we will need more information to assist with this enquiry, please send the answers to the questions below to [email protected]

GENERAL TIMBER SURFACES
- Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

Many of the intumescent paint systems are suitable for spray application. To assist with a specification please send the information below to [email protected]

- Level of fire protection required (i.e. 30, 60, 90min, etc.)
- Each steel section dimension (i.e. 254x146x37 UB)
- Quantity and length of each section (or overall meterage for each section)
- Orientation (horizontal or vertical)
- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)
- Building type (i.e. office, domestic, storage, etc.)
- Environment (internal, external, car park, chemical exposure, etc.)
- Application on site or in shop
Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

To assist with this enquiry we will need the information below, please send this to [email protected]

GENERAL TIMBER SURFACES
- Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

Thank you for the enquiry, we have contacted you directly for more information.

Thank you for the enquiry, please send the information below to [email protected]

GENERAL TIMBER SURFACES

- Size of surface area to paint

- Timber thickness

- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)

- Type of timber (i.e. pine, mdf, plywood, etc.)

- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)

- Internal or external

- Use (i.e. floor, wall cladding, ceiling, etc.)

- Clear or coloured coating required?

- Bare or previously coated?

Galvanised steel can be painted with a suitable intumesent paint system but will either require addition processes and or different primers to mild steel.

We will need the information below sending to [email protected] to assist with a specification.

- Level of fire protection required (i.e. 30, 60, 90min, etc.)
- Each steel section dimension (i.e. 254x146x37 UB)
- Quantity and length of each section (or overall meterage for each section)
- Orientation (horizontal or vertical)
- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)
- Building type (i.e. office, domestic, storage, etc.)
- Environment (internal, external, car park, chemical exposure, etc.)
- Application on site or in shop
Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Thank you for the enquiry, please can you provide the information below to [email protected] and we can assist with a specification.

- Level of Fire Protection required? (i.e. 30min, 60min, etc.)
- Style of door? (i.e. panelled, ledge & brace, etc.)
- Solid or hollow core? - (please note we cannot provide anything to upgrade hollow doors)
- Door size? (height and width)
- Door thickness? (include thickness at thinnest point (i.e. panel))
- Number of doors to do?
- Clear or coloured finish required?
- Bare or previously painted?

The manufacturers of the intumescent paint systems can offer certification after application.

We advise on this process when we send you a specification for the project.

You have not mentioned what the substrate is but if you can fill in the revelant questions below and send these to [email protected] we can assist you.

Steel

• Level of fire protection required (i.e. 30, 60, 90min, etc.)
  - Each steel section dimension (i.e. 254x146x37 UB)
  - Quantity and length of each section (or overall meterage for each section)
  - Orientation (horizontal or vertical)
  - Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
  - Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)
  - Building type (i.e. office, domestic, storage, etc.)
  - Environment (internal, external, car park, chemical exposure, etc.)
  - Application on site or in shop
  Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Timber

Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

Thank you for the enquiry, please send pictures of doors and the information below to [email protected] and we can assist with a specification.

- Level of Fire Protection required? (i.e. 30min, 60min, etc.)
- Style of door? (i.e. panelled, ledge & brace, etc.)
- Solid or hollow core? - (please note we cannot provide anything to upgrade hollow doors)
- Door size? (height and width)
- Door thickness? (include thickness at thinnest point (i.e. panel))
- Number of doors to do?
- Clear or coloured finish required?
- Bare or previously painted?

Thank you for the enquiry, we will need the information belwo sending to [email protected] to assist with a specification.

- Level of fire protection required (i.e. 30, 60, 90min, etc.)
- Each steel section dimension (i.e. 254x146x37 UB)
- Quantity and length of each section (or overall meterage for each section)
- Orientation (horizontal or vertical)
- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)
- Building type (i.e. office, domestic, storage, etc.)
- Environment (internal, external, car park, chemical exposure, etc.)
- Application on site or in shop
Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Assuming a class 0 level of fire protection is required from the paint to be applied, we can recommend Thermoguard Wallcoat BS Class 1/0 & EN Class B System.

This can be mixed to many RAL, NCS or BS colours.

Thank you for the enquiry, please send the information belwo to [email protected]

- Level of fire protection required (i.e. 30, 60, 90min, etc.)
- Each steel section dimension (i.e. 254x146x37 UB)
- Quantity and length of each section (or overall meterage for each section)
- Orientation (horizontal or vertical)
- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)
- Building type (i.e. office, domestic, storage, etc.)
- Environment (internal, external, car park, chemical exposure, etc.)
- Application on site or in shop
Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Thank you for the enquiry, we will need the information below emailing to [email protected].

GENERAL TIMBER SURFACES
- Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

Thank you for the enquiry, we will need the information below emailed to [email protected] to assist with this enquiry.

GENERAL TIMBER SURFACES
- Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

Thank you for the enquiry, please send the information below to [email protected] and we can assist with a recommendation.

GENERAL TIMBER SURFACES
- Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

Thank you for the enquiry, please send the information below to [email protected] and we can assist with a recommendation.

GENERAL TIMBER SURFACES
- Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

Steel

• Level of fire protection required (i.e. 30, 60, 90min, etc.)
  - Each steel section dimension (i.e. 254x146x37 UB)
  - Quantity and length of each section (or overall meterage for each section)
  - Orientation (horizontal or vertical)
  - Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
  - Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)
  - Building type (i.e. office, domestic, storage, etc.)
  - Environment (internal, external, car park, chemical exposure, etc.)
  - Application on site or in shop
  Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Thank you for the enquiry, we will need more information and pictures of this area to assist with this enquiry, please send these to [email protected].

Thank you for the enquiry, you will need to check with building control what level of fire protection they are willing to sign off.

We can assist with a specification for this application, we will need the information below sent to [email protected]

GENERAL TIMBER SURFACES
- Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

Thank you for the enquiry, please can you send the information below to [email protected] and we can assist with a specfication.

GENERAL TIMBER SURFACES
- Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

Please provide the information below to [email protected] and we can assist with a specification.

- Level of fire protection required (i.e. 30, 60, 90min, etc.)
- Each steel section dimension (i.e. 254x146x37 UB)
- Quantity and length of each section (or overall meterage for each section)
- Orientation (horizontal or vertical)
- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)
- Building type (i.e. office, domestic, storage, etc.)
- Environment (internal, external, car park, chemical exposure, etc.)
- Application on site or in shop
Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Thank you for the enquiry, please send the information below to [email protected] and we can assist with a specification.

- Level of fire protection required (i.e. 30, 60, 90min, etc.)
- Each steel section dimension (i.e. 254x146x37 UB)
- Quantity and length of each section (or overall meterage for each section)
- Orientation (horizontal or vertical)
- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)
- Building type (i.e. office, domestic, storage, etc.)
- Environment (internal, external, car park, chemical exposure, etc.)
- Application on site or in shop
Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Thank you for the enquiry, please send the information below to [email protected] and we can assist with a recommendation.

GENERAL TIMBER SURFACES
- Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

Thank you for the enquiry, please provide the informatino below to [email protected]

- Level of fire protection required (i.e. 30, 60, 90min, etc.)
- Each steel section dimension (i.e. 254x146x37 UB)
- Quantity and length of each section (or overall meterage for each section)
- Orientation (horizontal or vertical)
- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)
- Building type (i.e. office, domestic, storage, etc.)
- Environment (internal, external, car park, chemical exposure, etc.)
- Application on site or in shop
Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Thank you for the enquiry, unfortunately we do not have a product to recommend for this enquiry.

Thank you for the enquiry, please can you provide more information on what the door is made of and the sizes of the gap the seal must be suitable for to [email protected] 

To assist with this enquiry we will need more information. 

Please send the information below to [email protected]

- Level of fire protection required (i.e. 30, 60, 90min, etc.)
- Each steel section dimension (i.e. 254x146x37 UB)
- Quantity and length of each section (or overall meterage for each section)
- Orientation (horizontal or vertical)
- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)
- Building type (i.e. office, domestic, storage, etc.)
- Environment (internal, external, car park, chemical exposure, etc.)
- Application on site or in shop
Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Thank you for the enquiry, unfortunately we do not have a product we can recommend for this application.

Thank you for the enquiry, please provide the information below to [email protected]

- Level of fire protection required (i.e. 30, 60, 90min, etc.)
- Each steel section dimension (i.e. 254x146x37 UB)
- Quantity and length of each section (or overall meterage for each section)
- Orientation (horizontal or vertical)
- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)
- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)
- Building type (i.e. office, domestic, storage, etc.)
- Environment (internal, external, car park, chemical exposure, etc.)
- Application on site or in shop
Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Thank you for the enquiry, please can you provide more information on the make up of the ceiling and m² to [email protected].

Thank you for the enqiury, if you have exposed a timber beam we would recommend consulting the local building control officer on what level of fire protection they will require the beam to acheive.

To assist with a specification we will need the information below sent to [email protected]

GENERAL TIMBER SURFACES
- Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

This maybe possible assuming the substrates meet the minimum requirements of the systems, please provide the information below to [email protected]

GENERAL TIMBER SURFACES
- Size of surface area to paint
- Timber thickness
- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)
- Type of timber (i.e. pine, mdf, plywood, etc.)
- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)
- Internal or external
- Use (i.e. floor, wall cladding, ceiling, etc.)
- Clear or coloured coating required?
- Bare or previously coated?

If the doors in question have been painted with an intumescent paint system, the same system should be used to repair or repaint any areas with the manufacturers approval.

We do offer a Colour Match Service if you wish to send in a sample.

We can mix many paints to most RAL, NCS or BS colours.

If you require a specification for fire protecting doors please send the information below along with pictures of the doors to [email protected]

- Level of Fire Protection required? (i.e. 30min, 60min, etc.)
- Style of door? (i.e. panelled, ledge & brace, etc.)
- Solid or hollow core? - (please note we cannot provide anything to upgrade hollow doors)
- Door size? (height and width)
- Door thickness? (include thickness at thinnest point (i.e. panel))
- Number of doors to do?
- Clear or coloured finish required?
- Bare or previously painted?

Any fire protection coating should be regularly inspected and maintained.

The life span of any paint can vary dependant on the environment and exposure.

Please provide the information below along with pictures of the doors to [email protected]

- Level of Fire Protection required? (i.e. 30min, 60min, etc.)
- Style of door? (i.e. panelled, ledge & brace, etc.)
- Solid or hollow core? - (please note we cannot provide anything to upgrade hollow doors)
- Door size? (height and width)
- Door thickness? (include thickness at thinnest point (i.e. panel))
- Number of doors to do?
- Clear or coloured finish required?
- Bare or previously painted?

Please can you provide the information below to [email protected]

GENERAL TIMBER SURFACES

- Size of surface area to paint

- Timber thickness

- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)

- Type of timber (i.e. pine, mdf, plywood, etc.)

- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)

- Internal or external

- Use (i.e. floor, wall cladding, ceiling, etc.)

- Clear or coloured coating required?

- Bare or previously coated?

We will need further information to assist with recommending the right product, please can you send the information below to [email protected].

GENERAL TIMBER SURFACES

- Size of surface area to paint

- Timber thickness

- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)

- Type of timber (i.e. pine, mdf, plywood, etc.)

- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)

- Internal or external

- Use (i.e. floor, wall cladding, ceiling, etc.)

- Clear or coloured coating required?

- Bare or previously coated?

Thank you for the enquiry, we will need the information below to assist with a specification, please send this to [email protected]

- Level of fire protection required (i.e. 30, 60, 90min, etc.)

- Each steel section dimension (i.e. 254x146x37 UB)

- Quantity and length of each section (or overall meterage for each section)

- Orientation (horizontal or vertical)

- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)

- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)

- Building type (i.e. office, domestic, storage, etc.)

- Environment (internal, external, car park, chemical exposure, etc.)

- Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Certification from Thermoguard can be applied for using the link below.

Thermoguard Certificate Application.

Thank you for the enquiry, please can you provide more information and pictures of the areas in question to [email protected]

Assuming the plaster board ceiling is clean, dry, sound, prepared as detailed in the technical data sheet, approval is sought from building control prior to purchase and application you could consider Thermoguard Wallcoat 30 & 60 Minute System for Plasterboard.

This can achieve 30mins on 9mm plasterboard or 60mins on 12.5mm plasterboard.

Thank you for the enquiry, as this enquiry is for a fire protection we will require the information below to be sent to [email protected] to provide a specification.

GENERAL TIMBER SURFACES

- Size of surface area to paint

- Timber thickness

- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)

- Type of timber (i.e. pine, mdf, plywood, etc.)

- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)

- Internal or external

- Use (i.e. floor, wall cladding, ceiling, etc.)

- Clear or coloured coating required?

- Bare or previously coated?

A1 rating is non combustible, A2 rating is limited combustibility. 

Unfortunately we do not have a product we can recommend to acheive either of these ratings for this application.

Unfortunately we do not have a product we can recommend for this application.

Please provide the information below to [email protected] so we can assist with a specification.

- Level of fire protection required (i.e. 30, 60, 90min, etc.)

- Each steel section dimension (i.e. 254x146x37 UB)

- Quantity and length of each section (or overall meterage for each section)

- Orientation (horizontal or vertical)

- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)

- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)

- Building type (i.e. office, domestic, storage, etc.)

- Environment (internal, external, car park, chemical exposure, etc.)

- Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Assuming this is regarding fire protection your building control officer may request one to sign off the project. 

Certification can be applied for here.

FIRE CERTIFICATE APPLICATION

Thank you for the enquiry, please can you provide more information to [email protected] so we can assist.

Thank you for the enquiry, please can you provide the information below to [email protected]

GENERAL TIMBER SURFACES

- Size of surface area to paint

- Timber thickness

- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)

- Type of timber (i.e. pine, mdf, plywood, etc.)

- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)

- Internal or external

- Use (i.e. floor, wall cladding, ceiling, etc.)

- Clear or coloured coating required?

- Bare or previously coated?

Thank you for the enquiry, please can you provide the information below to [email protected] so we can assist with a recommendation.

GENERAL TIMBER SURFACES

- Size of surface area to paint

- Timber thickness

- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)

- Type of timber (i.e. pine, mdf, plywood, etc.)

- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)

- Internal or external

- Use (i.e. floor, wall cladding, ceiling, etc.)

- Clear or coloured coating required?

- Bare or previously coated?

The Thermoguard Fire Varnish systems are available in translucent colours for internal applications. 

Please provide the information below to [email protected] so we can assist with a specification.

GENERAL TIMBER SURFACES

- Size of surface area to paint

- Timber thickness

- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)

- Type of timber (i.e. pine, mdf, plywood, etc.)

- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)

- Internal or external

- Use (i.e. floor, wall cladding, ceiling, etc.)

- Clear or coloured coating required?

- Bare or previously coated?

We will need additional information to assist with this enquiry, please send the information below to [email protected]

GENERAL TIMBER SURFACES

- Size of surface area to paint

- Timber thickness

- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)

- Type of timber (i.e. pine, mdf, plywood, etc.)

- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)

- Internal or external

- Use (i.e. floor, wall cladding, ceiling, etc.)

- Clear or coloured coating required?

- Bare or previously coated?

Thank you for the enquiry, please follow the link below, complete and return the form to [email protected] so we can assist with a specification. 

Thermoguard Steel Enquiry Form

Jotun Steelmaster 600WF is made by Jotun.

Jotun do not issue certificates after application of their intumescent coatings. 

However, sometimes they calculate loadings based on a material list provided by the customer and generate a Client Schedule.

The applicator should provide any application records showing dry film thicknesses achieved on each section.

Based on both documents, the end customer should have confidence that the system was applied as per Jotun's schedules.

Client Schedules can also be generated by the applicator or dealer should they have access to the relevant loadings calculator in which case Jotun would not know the schedule for the specific project.

More information can be found on the Jotun Fire Certification Information page.

Please can you contact [email protected] with the information below so we can assist with a specification. 

How thick is the plasterboard?

If this is to be applied to mdf it should be primed first with Zinsser Bulls Eye 1-2-3.

Thank you for your enquiry, please provide us with as much of the following information as possible to [email protected] so we can assist with a specification.

GENERAL TIMBER SURFACES

- Size of surface area to paint

- Timber thickness

- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)

- Type of timber (i.e. pine, mdf, plywood, etc.)

- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)

- Internal or external

- Use (i.e. floor, wall cladding, ceiling, etc.)

- Clear or coloured coating required?

- Bare or previously coated?

Unfortunately we cannot advise on if you need an intumescent paint system or not, we would recommend to consult your local builder control department to ascertain if it is required.

If you need assistance with a specification for the intumescent paint system please provide the information below to [email protected]

Level of fire protection required (i.e. 30, 60, 90min, etc.)

- Each steel section dimension (i.e. 254x146x37 UB)

- Quantity and length of each section (or overall meterage for each section)

- Orientation (horizontal or vertical)

- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)

- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)

- Building type (i.e. office, domestic, storage, etc.)

- Environment (internal, external, car park, chemical exposure, etc.)

- Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Unfortunately manufacturers do not provide an expected lifespan, these coatings should be regularly inspected and maintained.

Thank you for your enquiry, please provide us with as much of the following information as possible to [email protected] so we can assist with a specification.

- Level of fire protection required (i.e. 30, 60, 90min, etc.)

- Each steel section dimension (i.e. 254x146x37 UB)

- Quantity and length of each section (or overall meterage for each section)

- Orientation (horizontal or vertical)

- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)

- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)

- Building type (i.e. office, domestic, storage, etc.)

- Environment (internal, external, car park, chemical exposure, etc.)

- Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Thank you for your enquiry, please provide us with as much of the following information as possible to [email protected]

GENERAL TIMBER SURFACES

- Size of surface area to paint

- Timber thickness

- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)

- Type of timber (i.e. pine, mdf, plywood, etc.)

- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)

- Internal or external

- Use (i.e. floor, wall cladding, ceiling, etc.)

- Clear or coloured coating required?

- Bare or previously coated?

Thank you for the enquiry, please provide the information below to [email protected] so we can assist with a specification. 

Thank you for your enquiry, please provide us with an image of the door(s) (if possible) and as much information as possible for the below points;

- Level of Fire Protection required? (i.e. 30min, 60min, etc.)

- Style of door? (i.e. panelled, ledge & brace, etc.)

- Solid or hollow core? - (please note we cannot provide anything to upgrade hollow doors)

- Door size? (height and width)

- Door thickness? (include thickness at thinnest point (i.e. panel))

- Number of doors to do?

- Clear or coloured finish required?

- Bare or previously painted?

We can assist with providing specification reports for intumescent paint systems from many manufacturers and also assist with the certification process.

Please provide the information below to [email protected] so we can assist with a specification.

Thank you for your enquiry, further to our telephone conversation, please provide us with as much of the following information as possible;

- Level of fire protection required (i.e. 30, 60, 90min, etc.)

- Each steel section dimension (i.e. 254x146x37 UB)

- Quantity and length of each section (or overall meterage for each section)

- Orientation (horizontal or vertical)

- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)

- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)

- Building type (i.e. office, domestic, storage, etc.)

- Environment (internal, external, car park, chemical exposure, etc.)

- Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

This would depend on which product this enquiry is regarding, please provide more information to [email protected] 

Thank you for the enquiry, please provide the information below to [email protected] so we can assist with a specification.

GENERAL TIMBER SURFACES

- Size of surface area to paint

- Timber thickness

- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)

- Type of timber (i.e. pine, mdf, plywood, etc.)

- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)

- Internal or external

- Use (i.e. floor, wall cladding, ceiling, etc.)

- Clear or coloured coating required?

- Bare or previously coated?

Thank you for the enquiry, please can you contact [email protected] with more information so we can look into this for you.

Thank you for the enquiry, please provide the information below to [email protected] so we can assist with a specification. 

- Level of fire protection required (i.e. 30, 60, 90min, etc.)

- Each steel section dimension (i.e. 254x146x37 UB)

- Quantity and length of each section (or overall meterage for each section)

- Orientation (horizontal or vertical)

- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)

- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)

- Building type (i.e. office, domestic, storage, etc.)

- Environment (internal, external, car park, chemical exposure, etc.)

- Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Thank you for the enquiry, please provide the information below to [email protected] so we can assist with a specification.

- Level of fire protection required (i.e. 30, 60, 90min, etc.)

- Each steel section dimension (i.e. 254x146x37 UB)

- Quantity and length of each section (or overall meterage for each section)

- Orientation (horizontal or vertical)

- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)

- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)

- Building type (i.e. office, domestic, storage, etc.)

- Environment (internal, external, car park, chemical exposure, etc.)

- Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

To assist with a specification for the steel we would need the information below sending to [email protected]

- Level of fire protection required (i.e. 30, 60, 90min, etc.)

- Each steel section dimension (i.e. 254x146x37 UB)

- Quantity and length of each section (or overall meterage for each section)

- Orientation (horizontal or vertical)

- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)

- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)

- Building type (i.e. office, domestic, storage, etc.)

- Environment (internal, external, car park, chemical exposure, etc.)

- Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Please see the link below to apply for certification from the manufacturer.

FIRE CERTIFICATE APPLICATION

Thank you for the enquiry we have contacted you directly by email to assist.

For this application assuming the concrete is bare, clean, dry, sound and prepared you could consider the Thermoguard Wallcoat BS Class 1/0 & EN Class B System.

This can be mixed to many RAL, NCS or BS colours in a matt or eggshell finish.

We would recommend to seek approval from Building Control prior to purchase and application.

Thank you for the enquiry, we would need the information below to assist with a specification, please send this to [email protected]

- Level of fire protection required (i.e. 30, 60, 90min, etc.)

- Each steel section dimension (i.e. 254x146x37 UB)

- Quantity and length of each section (or overall meterage for each section)

- Orientation (horizontal or vertical)

- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)

- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)

- Building type (i.e. office, domestic, storage, etc.)

- Environment (internal, external, car park, chemical exposure, etc.)

- Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

Thank you for the enquiry, we have contacted you directly by email. 

Certification for fire protection products can be applied for on the link below. 

FIRE CERTIFICATE APPLICATION

Certification can be applied for from Thermoguard using the link below. 

THERMOGUARD FIRE CERTIFICATE APPLICATION

Thank you for the enquiry, please contact [email protected] with more information so we can assist with a specification.

It would be unusual to be asked to achieve class 1 or 0 on metal, we would recommend to consult building control on what level of fire protection you require. 

We have emailed you directly with the forms we would require completing to assist with a specification. 

Thank you for the enquiry, we would need more information to assist with a specification, please provide the information below to [email protected]

GENERAL TIMBER SURFACES

- Size of surface area to paint

- Timber thickness

- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)

- Type of timber (i.e. pine, mdf, plywood, etc.)

- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)

- Internal or external

- Use (i.e. floor, wall cladding, ceiling, etc.)

- Clear or coloured coating required?

- Bare or previously coated?

Thank you for the enquiry, please see the link below, we would required the form to be completed to assist. 

THERMOGUARD FIRE APPLICATION FORMS

Thank you for the enquiry, to assist with a specification we would the plasterboard form completing on the link below. 

THERMOGUARD FIRE APPLICATION FORMS

You do not need to be trained or approved to apply the Thermoguard systems, but the doors must be suitable to be upgraded and approval from building control should be sought prior to purchase and application. 

Please complete the For Doors form linked below so we can assist with a specification.

https://www.rawlinspaints.com/content/thermoguard-fire-application-forms

Thank you for the enquiry, please complete the form on the link below so we can assist with a specification. 

THERMOGUARD FIRE APPLICATION FORMS,

Unfortunately no.

Intumescents are not a suitable means of fire protection for the insulation criteria of REI.

The problem is that the insulation criteria requires a maximum temperature rise on the non-fire side of 140 degrees C and since thin film intumescent is designed to react to substrate temperatures of around 200 C then the system will fail, as the insulation maximum will be surpassed before the intumescent expands.

The steel will require to be protected by other means to achieve the insulation criteria.

Thank you for the enquiry, please complete and return the steel form on the link below. 

THERMOGUARD FIRE APPLICATION FORMS

Thank you for the enquiry, please complete the plasterboard form on the link below so we can assist with a specification.

THERMOGUARD FIRE APPLICATION FORMS

Thank you for the enquiry, for fire protection enquiries we need detailed information on the steels. Please complete the steel form on the link below so we can assist. 

THERMOGUARD FIRE APPLICATION FORMS

Thank you for the enquiry, please can you provide more information to [email protected] so we can assist with this enquiry.

Thank you for the enquiry, please complete the steel form on the link below so we can assist with a specification.

Thermoguard Fire Application Forms

Unfortunately the Zeroflame Fire Retardant Treatment cannot be used on plywood.

Thank you for the enquiry, please complete the steel and timber forms on the link below so we can assist with a specification.

Thermoguard Fire Application Forms.

Thank you for the enquiry, if a level of fire protection is required we will need to ask for more information, please complete the steel form on the link below. 

Thermoguard Fire Application Forms

Intumescent paints cannot be used on cold rolled steel, so it would be unlikely the container roof could be protected in this way. 

Please provide the information below to [email protected] so we can assist with a specification.

- Level of fire protection required (i.e. 30, 60, 90min, etc.)

- Each steel section dimension (i.e. 254x146x37 UB)

- Quantity and length of each section (or overall meterage for each section)

- Orientation (horizontal or vertical)

- Number of sides to be painted (all sides, 3 sides, 1 flange, etc.)

- Structural Steel Design Code (i.e. EuroCode, BS5950, BS476; Part 21, etc.)

- Building type (i.e. office, domestic, storage, etc.)

- Environment (internal, external, car park, chemical exposure, etc.)

- Application on site or in shop

Alternatively you can just forward us drawings, fabrication/cutting lists and we'll extract the information from them but in that instance we'd need some guidance as to what to allow for i.e. all steels on first floor, etc.

We would recommend to consult building control and the manufacturer of the fire board to ascertain if it can be painted without affecting the boards fire rating.

Also what level of fire protection any possible coating for the board would require if any.

Thank you for the enquiry, we would need more information on the project to assist with a specification please complete and return the timber form on the link below. 

Thermoguard Fire Application Forms

Assuming you need a level of fire protection we will need more information to assist. 

Please complete and return the Steel form on the link below.

Thermoguard Fire Application Forms

We will need further information to assist with this enquiry, please complete and return the timber form from the link below. 

Thermoguard Fire Application Forms

These products need to be specified, please complete the timber form on the link below so we can assist.

Thermoguard Fire Application Forms

These products need to be specified, please complete the steel form on the link below so we can assist.

Thermoguard Fire Application Forms

To assist with a specification we will require the steel form completing on the link below. 

Thermoguard Fire Application Forms

Unfortunately we do not have an intumescent paint product suitable for this application. 

Please complete the timber form on the link below so we can assist with a specification. 

Thermoguard Fire Application Forms

Please complete the steel form on the link below so we can assist with a specification. 

Thermoguard Fire Application Forms

Thank you for the enquiry, please complete the steel form on the link below so we can assist with a specification. 

Thermoguard Fire Application Forms

Please complete the steel form on the link below so we can assist with a specification.

Thermoguard Fire Application Forms

Unfortunately no, this system can only be over painted with the manufacturers approved topcoat below assuming the system was applied to timber but not doors.

This can be mixed to many RAL, NCS or BS colours. 

Thermoguard Smoke & Flame Retardant Dualcoat