Need Help?

Problem Solving

How do you treat rising damp?

Our blog post "Treating Rising Damp" shows you how to spot the problem, ways to solve it, and the products to use.

Which Clear varnish can i use below the waterline

Assuming the substrate is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Teamac High Performance Polyurethane Topcoat.

Your paints have been recommended. So wondering what i need to paint on the internal walls to stop the damp and mould coming through? . . .

Thank you for the enquiry, we have contacted you directly for more information.

Hi, do you have a paint I can use on a fireplace marble back panel and hearth?

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

hi Guys Need to talk to some one about expansion joints. job description to repair a defective expansion joint. . . .

Thank you for the enquiry, we have contacted you directly.

Sirs, Paint on the upper surface of my oven door was damaged by chemicals whilst being professionally cleaned - and needs to be repainted (black). I'm aware that small tins of heat resistant paints can be bought for.touching up rad . . .

Unfortunately we do not have a product to recommend for this application.

what is the remedy removing gloss patches on matt finish two pack polyurethane applied on pacquet floor

As the previously applied coating wears gloss patches will occur, to correct this assuming the floor is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum 4900 Polycoat 2K.

I'm looking for a waterproofing paint to use on an area of a fibre cement corrugated garage roof. The roof is old and not safe to climb onto. There is a small problem area with very fine cracks that leaks. Do you supply a suitable . . .

Assuming there is no large cracks or gaps, the roof is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend GacoPatch for application to the inside of this roof.

Do you have an interior paint for gypsum board ceilings that will work as a vapour barrier (and ideally has acceptable self-finish)? It would be applied to domestic rooms including bedrooms and bathrooms. . . .

Thank you for the enquiry, we have contacted you directly for more information.

Hi, I am secretary to a group of volunteers laying a pebble path originally laid by children under lockdown. We want to make the path permanent and have laid painted pebbles in concrete. We now want to seal the path to prevent fadi . . .

Assuming the substrates are clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend 3 coats of Rust-Oleum 4900 Polycoat 2K.
We would recommend testing on a small area for compatibility and adhesion prior to full application.

I have an old (50 year old) mobile home (large caravan) It is clad on the sides with aluminum sheet and that has been painted with some sort of artex. But the ends are plywood, external ply I guess. i prefer a smooth finish. I hope . . .

Thank you for the enquiry, we have contacted you directly for more information.

I have a flat roof that has a plastic type covering that has now deteriorated and water is coming through . The costs to replace it are massive so am looking for a paint that will waterproof the surface . I live in Gibraltar so it . . .

Thank you for the enquiry, we have contacted you directly for more information.

Hi, I am after an external waterproof masonry paint in white for garage walls. Is there anything you suggest? Many thanks . . .

Assuming the walls are clean,dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Wethertex AP77 Flexible Smooth Masonry Paint.

This is available in many RAL and BS colours.

I require to paint an aluminium painted motorhome roof. The corrosion holes and mechanical based holes have been patched. Now I require a waterproof paint system to protect the roof. I can’t apply the system undercover due to the . . .

Assuming the substrate is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend GacoPro Roof Coating and GacoFlex 66S Tape for any edges or joins.

Hi I have stone mullions around my double glazing, which are prone to black mould (this is internally by the way). I need a solution which eliminates or reduces the mould and works on stone, so would I use an external masonary pain . . .

Assuming the stone mullions are clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Zinsser Bulls Eye 1-2-3 followed by Zinsser Perma-White Interior.

This is a mould resistant paint, available in many RAL and BS colour in a matt or satin finish.

HI, i have a garage roof that is block paved on top forming a raised patio area. The roof has become very porous and I was wondering if there is a clear liquid sealer that i could put over the block paving that would seal the pavin . . .

Unfortunatley we do not have a product to recommend that could be applied without lifting the block paving first.

We have contacted you directly for more information to explore this option for you.

My GRP roof is leaking due to a number of small pin holes, should I buy the Cromapol FIBRE FREE? the FIBRE option appears to be for more heavy duty cracks. Thanks . . .

Assuming the roof is clean, dry, sound and prepared as detailed in Technical Data Sheet we can recommend the fibre re-inforced formula Cromar Cromapol Acrylic Roof Coating as a quick fix solution to repair the pin holes.

This will remain tacky.

Are any of your anti slip paints OK to paint onto indoor terracotta tiles in a toilet/ washbasin area of a locker room? . . .

Assuming the tiles are clean dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Smartkote Safekote.

This is available in a range of colours and a clear option and is a barefoot frinedly anti-slip paint.

The tiles will need to be primed with Protectakote Clear Primer Treatment prior to application.

hi, we have a flat ashfelt roof approx 15m x 3m which is starting to crack. which product would you recommend that will still allow us pedestrian access? . . .

Thank you for the enquiry, we have contacted you directly for more information.

Good afternoon. Can you tell me if there are stockists of Rawlins Flexible Floor Coating the Republic of Ireland? many thanks. . . .

Unfortunately, we do not have stockists in the Republic of Ireland, but you can place an order on the website and we can ship the order to you.

Hello.I am looking for the best product to paint my ceilings with to keep Heat in.? What do You recomend. Thanks. Drew . . .

I'm afraid we currently have nothing we could recommend for application on to internal surfaces to reduce heat loss.

We have recently taken Zinsser Allcoat Exterior Satin from you, RAL9001 to cover existing windows and fascia, etc. Today we have had new windows fitted finished in RAL 9001 and there is a marked shade difference. If I bring a sampl . . .

Unfortunately we can only match it to the nearest RAL or BS colour code, there can be a variance in colours to the same RAL code.

Hello , I need which product is suitable to protect my painting on wood or metal surface from high heat ,,,very high heat like putting on surface tray just taken out from oven. any supplier to u in Lebanon to contact and buy this p . . .

Unfortunately we do not have a product to recommend for this application.

The paint is bubbling off the side of an awning. Unfortunately the part cannot be replaced as it is no longer manufactured. The company advices me it is made from aluminium. It is a very small area (say 9 square inches). What woud . . .

Assuming the aluminium is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Zinsser Bulls Eye 1-2-3 followed by 2 coats of Zinsser AllCoat Exterior (Water Based).

This is available in many RAL and BS colours in a matt, satin or gloss finish.

Afternoon, I’ve been recommended rust oleum combicolour to paint my caravan. I’m after a silver/aluminium metallic finish. What colour paint would you recommend? Thanks Phil . . .

This paint can be mixed to many RAL and BS colours including some metallic options, we would recommend looking at a RAL colour chart to find a suitable colour.

The RAL colours that are metallic silver shades would be 9006, 9007, 7048, 9022 and 9023.

I am looking to apply intumescent paint on a plastic connector. I was curious first what your recommendation would be for that application (wood, steel, or some other type of intumescent paint). Can I get a small sample for some te . . .

Thank you for the enquiry, unfortunately we do not have an intumescent paint we can recommend for application to plastic and the manufacturers do not produce tester pots.

I have a garage floor that has had tanking slurry applied. However in very high levels of rain there is still some ingress, I have been told that this is probably vapour. Have you a product that you recommend that will fully seal o . . .

Thank you for the enquiry, we have contacted you directly for more information.

Hi I need to paint lines on a warehouse floor but need a near odourless paint to do so. (We store milk powder and it absorbs odours easily) Thanks . . .

Assuming the warehouse floor is concrete, it is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend 602 HD Line Marking Paint.

This is a solvent free, low odour epoxy.

Hi we have a 6mtr rhib with fibreglass hull. Can you recommend what paint is needed for below the waterline. We don't need anti foul as not staying in the water. . . .

Assuming the fibreglass hull is bare, clean, dry, sound and prepared as detailed in the Technical Data sheet we can recommend Teamac High Performance 2 Pack Zinc Phosphate Primer followed by Teamac High Performance Polyurethane Topcoat.

This is available in clear or many RAL and BS colours in a gloss finish.

Dear Sirs, As architects currently involved with an existing cantilevered concrete balcony which has been leaking rainwater through to a supporting beam within a public area below. We would like to remove the existing failed weathe . . .

Thank you for the enquiry, we have contacted you directly for more information.

Rendered outdoor steps with water run off from raised patio area are staining with green algae and dirt . Can you recommend a product to seal the wall and repel this dirt problem in a white finish so we can just hose it down in the . . .

Thank you for the enquiry, we have contacted you directly for more information.

i have here a can of what i thought is callled bronze green, the origanal classic land rover paint, the only code i can find it hmp329, i cant find this on your web site, any ideas please?? th e cand is 1lt perchoused from jsf land . . .

Thank you for the enquiry, unfortunately we cannot mix to an automotive paint code, we have contacted you directly for more information.

Is there any product that will give a strong protective cover over Rust-Oleum Painters Touch Toy paint used on an outdoor wooden play frame in a public park? . . .

Rust-Oleum Painters Touch is not a paint we stock, assuming the previously painted substrate is clean, dry, sound and prepared as detailed in the Technical Data sheet we can recommend Rust-Oleum Crystal Clear.

This can be applied over painted surfaces but we would recommend testing for compatibility and adhesion prior to full application.

I have a metal water feature which I would like to refurbishe as it is a bit fadden and rusty. Could you recommend a pwint to use. Thanks . . .

If you are able to get back down to bare metal we would recommend priming with Teamac Metaclor Antifouling Primer before applying 2 coats of Teamac Chlorvar Chlorinated Rubber.

I have a grp roof it's about 7 years old and it's starting leaking. There is no visible signs of anything. Was looking to get a top coat or something to go over it. The roof is 6x4.5m . . .

We can recommend KoverTek TekShield Premium GRP Roof Kit as a repair system on GRP which also offers the options of a 20year or 25year warranty.

Hi I will be laying a new step. I am using unglazed terracotta quarry tiles which have been painted with acrylic painted Some all over some only partly. Which product can I seal them with bearing in mind they will be walked on. Tha . . .

Smartkote Safekote is a clear anti-slip coating that can be applied to numerous substrates.

I need a magnolia weather proof paint for rendering. What do you recommend please?

Assuming it is a cement based render it is bare clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Wethertex ST1 Quick Dry Stabilising Primer followed by Wethertex AP77 Flexible Smooth Masonry Paint.

This is available in many RAL and BS colours in a matt finish.

Hi. At the outset, I want to say that I am impressed by your offer and the wide range of products. I have a problem finding the right product that will help me get the job done. My job is to build interior oak furniture and paint/c . . .

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Please may I ask which colour of your smooth masonry paint would match gun metal grey please for a brick house paint thank you for your advice . . .

Thank you for the enquiry, many of the paints we stock can be mixed to many RAL and BS colours, we would recommend viewing a RAL or BS colour chart in person to ascertain suitability of a colour.

Thank you for your response on my Email. So if I buy AP77 masonry paint can you put over an old masonry paint which is years old and it still give you protection? Thanks . . .

Assuming the previously applied masonry paint is clean, dry, sound and prepared as detailed in the Technical Data Sheet, Wethertex AP77 Flexible Smooth Masonry Paint can be applied over the top of most paints.

We would recommend testing for compatibility and adhesion prior to full application.

Hi, I am renovating an old GRP sailing boat, finishing with International Perfection undercoat and top coat. I have somehow lost a 187ml tin of International Perfection Undercoat Curing Agent that was supplied with the White High P . . .

Thank you for the enquiry, unfortunately this is not a product we stock.

Good afternoon. I am currently building a side extension and having the entire bungalow newly rendered. Render will be smooth except for the wall that adjoins a footpath, that area will be rough texture to help prevent vandalism/gr . . .

We would recommend viewing a RAL or BS colour chart in person to ascetain the suitability of a colour for your project. We have contacted you directly for more information to assist with a recommendation.

Can I thin down rustoleum paint and with what type of thinners. Also I have aluminium garden furniture that has been cleaned and sprayed with etch primer, can you tell me what kind of paint I need to use. Thank you Mike . . .

Some Rust-Oleum paints can be thinned, this will be stated on the technical data sheet for the product.

Assuming you test for compatibility and adhesion prior to full application, the primed substrate is clean, dry, sound and prepared as detailed in the Technical data sheet we can recommend Rust-Oleum Combicolor Original for this application.

Hi I have used your paint and wanted to know what I could put over it to protect it like a varnish I have it put it on my work surface in my caravan and used the paint advised to me by a man in one of the shops selling this paint. . . .

Thank you for the enquiry, we have contacted you directly for more information.

Hi, I'm looking for a highly corrosion resistant, long lasting product, (white, preferably glossy), to paint directly on to lightly corroded metal gates and railings. What would recommend ? Many thanks. . . .

Assuming the gates are steel, clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by Rust-Oleum CombiColor Original.

This is available in many RAL and BS colours in a gloss or satin finish.

What spray do i need to coat my white rusty metal garden bench?

Rust-Oleum CombiColor Original Aerosols can be used for application over existing paints and directly to bare metal. The surface should be clean, dry and any existing rust should be removed prior to application. The simplest way of preparing the steel would be to use a wire brush to remove all loose and flaking rust before painting.

Is there any paint I can use on my previously stained decking, that can go straight on without the need for sanding or stripping the decking first. Thank you . . .

We would suggest Blackfriar Anti-Slip Deck Coating here, test a small area first to ensure compatability, appearance, adhesion etc. before doing the whole area.

Hiya, I have a liquid rubber roof on top of a bitumen coated roof, it’s wonderful except when the sun beams on it, then it stinks of bitumen . . .

Thank you for your enquiry, unfortunately we wouldn't have anything to offer to combat this problem for you.

I have a back yard that was once part of a car park. The tarmac is rough in places and appreciate that I may need more than one coating to completely level it. I want to coat the surface with something more colourful and smooth. Wh . . .

We would recommend Rust-Oleum Tarmacoat which can be applied directly to clean, dry tarmac and is available in a range of standard colours. It is not designed as a levelling coating but if you apply a couple of coats it may assist in filling in very shallow depths.

Hello sir'so I want to paint my motorcycle cylinders with silver paint,got to be heat resistant,gloss and smooth. Can you help? Have you any product that would be ideal. Thank you i would be most grateful for a reply. Andrew . . .

We would recommend Rust-Oleum Heat Resistant Paint 750°C for your application which is available in a metallic Aluminium finish.

Hi there, I was planning on repainting old floorboards with a white wash paint but the floorboards are coated in what seems to be a bitumen paint. What would you recommend to prepare the wood for painting? . . .

We would recommend Hydron AG4 Graffiti Remover to assist in removing the existing bitumen from the floor before applying any paint coatings.

Hi, I’m looking for a white exterior non slip paint for some newly laid concrete steps . Would be grateful for your advice please. Would it be possible to get next day delivery? Thanks Gary . . .

We would recommend Smartkote Protectakote UVR for this application but new concrete must be left a minimum of 28 days to cure before painting.

What is your best metal primer for cast iron Pergola,also your best system for top coats please.Has some bad rust in few places. Any cleaning will be done manual,grinding,etc. Not so concerned about cost as the right product is mor . . .

We would recommend bare rusty surfaces be primed with Rust-Oleum 769/780 Damp-Proof Rust Primer which is left for 24 hours before overcoating with Rust-Oleum CombiColor.

I need a coating/paint suitable for external masonry that is capable of withstanding extreme heat and will protect the render from cracking. Is there anything you can suggest? The render is already cracked so if there is anything t . . .

We're able to offer a waterproofing, flexible and crack bridging product in way of Rust-Oleum Mathys Murfill Waterproofing Coating. This can be applied to old, sound paintwork following thorough brushing down. If the surface is bare or the paint surface is chalking, you wuold need to first prime the surafce with Mathys Pegafix. Any cracks larger than 0.5mm would need filling with Rust-Oleum Mathys Elastofill. The system will not necessarily prevent further cracks in the substrate but the flexibility in the coating will prevent cracks from showing.

What paint do I need for a wood burner

Blackfriar High-Heat Resistant Paint would be recommended for applying a black, heat resistant finish on the externals of a wood burner.

Is there anywhere in the Glasgow area sells fire retardant paint for metal

We're a stand alone distributor based in Leeds but can deliver nationally with a range of delivery options should you wish to place an order online or with our sales team.

Im looking for a suitable paint that I can use to cover a marble backplate & hearth on a fireplace, preferably white or grey colouring - do you have anything suitable ? . . .

Please see our blog post - Painting the Walls around a Fireplace or Multi Fuel Stove

We have two small small areas of flat roof that were delivered and installed as one piece. The top is some kind of polycarbonate/fiberglass. One roof faces south and gets sun all day and is starting to fade. We would like to take p . . .

GacoPro Roof Coating can be applied directly to fibreglass.

Dear sir/ madam, I require a non slip exterior paint for old concrete stairs. Something hard wearing but definitely non slip. Please advise. Please include postage. Regards, Ken Sethi . . .

We would recommend Coo-Var Suregrip Anti-Slip Floor Paint.

hi can you please advice me on the right epoxy resin to use in a wet room just like it to be plan white resin Thanks . . .

Assuming application is on to prepared concrete, 503 Easy Clean Anti Slip Coating is available in white and includes a fine particle anti slip additive that is pre-dispersed into the resin and held in suspension. The result provides a ready to use product that leaves an evenly textured, slip resistant surface that is easy to clean and extremely durable.

What paint is suitable for inside of a wide open concrete fireplace (with cast iron fire back and log basket) in Red oxide Thank you . . .

Please see our blog post: Painting the Walls around a Fireplace or Multi Fuel Stove

I had a slab of concrete laid last year for a garden shed. After rainfall I get pools of water leaching up through the subsurface and through the concrete. Is there any product that I can use to seal the concrete? Thanks Haydn . . .

When dry, we would recommend trying our 402 Damp Proof Coating.

Can you recommend a paint to paint over plastic bathroom wall cladding. The top finish is flaking away directly inside the shower cubicle. Thanks . . .

Unfortunately we wouldn't have anything suitable for this application.

Hi What would you reccomend for a waterproof covering for a recently laid EPDM rubber flat roof. There will be some pooling, and we have 2x skylights in the flat roof Primarily looking to ensure it remains watertight, but would lik . . .

GacoPro Roof Coating would be our recommendation for this as it can be applied directly to EPDM.

Please can you recommend the appropriate product for a small ramp (approx 1m x 1.5m) which is used by my elderly father to access his garden. The concrete ramp was painted with a type of grey anti-slip paint BUT this did not have a . . .

Try Coo-Var Suregrip Anti-Slip Floor Paint, this has a very coarse texture to it.

Can any of your paints be used on side walls of non metal sided motorhome

Rust-Oleum CombiColor Multi-Surface would be a good product to trial for this application.

I want to paint my fire surround, which is plaster based, what do you recommend, and what colours do you have. . . .

Please see our blog post: Painting the Walls around a Fireplace or Multi Fuel Stove

Hi there, I am wanting to paint a spit roast. Pls could you advise me which paint you think would suit best? Many thanks, Shell . . .

Rust-Oleum Heat Resistant Paint 750°C could be used for all areas not in direct contact with flames or food.

Hi guys wonder if you can help ..I have a few small repairs to make on exterior tryolean coated textured wall . Knowing nothing about this I have been watching you tube clips about a product called rapid set stucco repair that leav . . .

You could try something like Wethertex HBS Flex-Coat Hi-Build Coating, we have no specific experience over 'tryolean' but it may give a similar finish to the American product you have found to carry out small repairs.

I have a gold metal trim around my fire place which i would like to change to silver its quite close to fire so would have to be fire resistant any ideas. Thank you . . .

Please refer to our Blog post: Painting the Walls around a Fireplace or Multi Fuel Stove

Hi, I want to paint the inside of my inglenook. It is finished in fireproof cement render and will have an open fire in it (on a grate, not in an insert). Please could you advise the best paint to use? Thank you! . . .

Please refer to our Blog post: Painting the Walls around a Fireplace or Multi Fuel Stove

You advise testing. Are sample or small quantities available?

Could you advise which product you are enquiring about please?

hello, i have a 1960's house with a shallow pitch tiled roof. the tiles are large flat Marley tiles. the valleys are tiled as well and we seem to have developed a leak somewhere with water ending up inside. what is the best roof pa . . .

Bedec Super-Flex can be applied directly to marley/concrete tile to provide a flexible & seamless waterproof finish andis available in a range of standard colours. The 1st coat should be thinned 30% with clean water before applying the product undiluted.

I want to paint the griddle on my gas stove. What product I should buy? Can I match the existing color or near enough . . .

Unfortunately we currently have no products we could offer for direct heat contact.

I have both plastic and metal drain covers around the perimeter of my house. In the wet and in icy conditions they get very slippery. Would one of your non-slip rapes be a suitable solution for outdoor areas? Thank you. . . .

We would recommend Smartkote Protectatkote UVR to create an anti-slip finish on external drain covers. You would need to the prime the metal with Smartkote Protectakote 2K Metal Primer before applying Protectakote UVR. The plastic ones would need to be abraded to create a key and then cleaned down with Xylene prior to applying Protectakote UVR.

Hi, I am looking for a small amount possibly a sample if possible of white road marking paint and wondered if this was something that you could provide? I have recently had a white parking line painted accross my driveway at home b . . .

Blackfriar Professional Line Marking Paint is available in a 1lt tin and is compatible with existing road line paints.

I have used combicolor on a vwt25 van several years ago. I now have a grp bodied car i want to roller paint. Can i use the combicolor ( l need it's flexibility for the fibreglass) or do you have a specific paint for grp? Ideally ra . . .

Rust-Oleum CombiColor Multi-Surface is available in RAL 9010 and can be applied to GRP once it is clean and has been lightly abraded.

Hi , I'm looking to paint a chimney fire breast that a wood burning stove is inserted, can you please help as to what sort of paint is recommended? Would I use a heat resisting or a flame retarded paint, Regards Paul Gaffney . . .

Please see our blog post to assist with your application - https://www.rawlinspaints.com/blog/painting-the-walls-around-a-fireplace-or-multi-fuel-stove/

Hi my shed felt is leaking what type of paint would I use

Rust-Oleum Mathys Fillcoat Fibres is suitable for application on to most roofing substrates to provide an immediae waterproofing finish

Hi, We have an open brick fireplace and want to paint the walls inside the hole but want to make it safe. It was painted rdd by previous owners but we want to change colour. Can we use a standard paint then cover with fire resistan . . .

Please see our blog post: Painting the Walls around a Fireplace or Multi Fuel Stove

How to I paint metal garage doors?

Our blog post "How To Paint Metal Garage Doors" shows you how to prepare, prime and paint domestic garage doors as well as commercial and industrial roller shutters, with recommended products to use.

How do I paint over mould?

See our blog post "Quick & Cost-Effective Ways To Paint Over Mould" for help on preparing, priming and painting over mould on walls and ceilings. The article also recommends products to use, and you can find more in our mould & damp proof paints category.

Be aware that rising damp is often misdiagnosed as mould and requires a more extensive solution – see our guide on Treating Rising Damp.

Can I paint over wallpaper? I just moved house and I really can't be bothered to strip everything off of the walls. . . .

You can - try Zinsser's Wallpaper Cover-Up which obliterates wallpaper print with a smooth matt, off-white finish and can be overpainted with any conventional emulsion the same day - certainly saves time if you're moved to a new house or business premises.

We've also written a blog post "How to Paint Over Wallpaper" which details how to prepare the surface before painting with Zinsser Wallpaper Cover-Up.

How to paint over nicotine stains?

Read our blog post on how to quickly and easily cover over nicotine stains blighting existing indoor paintwork.

How to paint over outdoor graffiti & tagging?

Our blog post "How To Paint Over Outdoor Graffiti" will show you how to make light work of unwanted graffiti and tagging, priming and sealing the substrate in one to prevent stains from resurfacing.

How to paint chalky exterior walls?

Prepare, prime and finish weathered and chalky exterior walls with our blog post, which also contains links to recommended products.

How to paint surfaces exposed to high humidity?

Our blog post on high humidity paints recommends effective products and will show you how to prepare, prime and decorate surfaces exposed to high humidity, often in bathrooms, kitchens, changing rooms, etc.

How to paint over fire and smoke damage?

We have a few blog posts on this topic, including using water-based products and for odourless application:

How To Paint Over Interior Fire Damage
How To Paint Over Fire And Smoke Damage (Water-Based Method)
How To Paint Over Fire Damage (Odourless Method)

How to paint friable exterior walls?

See our blog post for a tried and tested method on painting friable walls with steps to prepare, prime and decorate, preventing paint from flaking and peeling back off the surface.

How to paint ceramic tiles?

Conventional paints won't adhere properly to ceramic tiles - read our blog post for how to properly prime and decorate tiled surfaces, and the products we recommend to use.

How to paint woodstained or varnished surfaces

Our 3-step guide below explains how to prepare and finish woodstained or varnished surfaces effectively, without all the tedious sanding, using Zinsser products to prime, seal and decorate quickly.

How to paint over water stains

Our blog has articles covering how to paint over water stains, both previously-painted surfaces and with odourless products:

How To Paint Previously Painted Water Stained Surfaces
How To Paint Over Water Stains (Odourless Method)

How to paint over efflorescence

Our blog post covers how to paint over efflorescence and recommends products to use.

How to paint over fibreglass

Read our 3-step guide on our blog on how to paint over fibreglass for interior and exterior projects

How to paint over powder coatings

See our blog for a 3-step guide on painting over powder coatings to prepare, prime and decorate.

How to paint bitumen and asphalt

See our blog post on how to prepare, suitably prime and finish the surface.

How to paint steel

See our blog post "How To Paint Steel" for preparation and decoration tips as well as recommended products.

How to paint exterior mildew areas

Our 3 step guide on our blog will show you how to paint over exterior mildew with no bleed through.

If you're looking for help with how to treat interior mould and mildew, see the articles below:

Treating Rising Damp
Quick & Cost-Effective Ways To Paint Over Mould
How to Spot the Early Signs of Damp
What Causes Damp and Mould on Walls, and How to Fix It

How to paint MDF

Our blog has a guide to painting MDF, along with products recommendations.

How to paint limewash/distemper walls

Our 4-step guide will show you how to prepare, prime and decorate interior limewash and distemper walls, with product recommendations.

How To Paint Lead

The 3-step guide on our blog will show you how to paint lead, sealing the substrate to help prevent it from causing harm.

How to paint knotted and resinous timber

Follow the steps on our blog post, which also recommends the best products for the job.

How to paint glossy and slick surfaces

This 3-step guide on our blog shows you how to paint glossy, impermeable surfaces, with links to recommended products.

I have a chrome surround, which surrounds my open fireplace, I would like to paint this a brass colour. Can you suggest a fireproof paint? Thanks very much. Lisa . . .

Please see our blog post: Painting the Walls around a Fireplace or Multi Fuel Stove

How can I stop my new wooden gazebo roof from keaking

If the structure is new we would suggest speaking to whoever you purchased it from / installed it for you. However, as a short term fix it could be worth trying something like Rust-Oleum LeakSeal on a small area to see if this is effective as it comes in clear so would try to keep the look of the roof for you. This obviously can't be guaranteed but may help until a permanent solution can be found with the sellers/installers.

I am looking for a paint/spray that I can put ontp an external wall that will reflect my car reversing lights so I can see where a low brick wall is nex tot my drive in this dark weather. Dont want to spend too much what can you re . . .

We don't have anything in a paint form for this but we would suggest one of the Heskins range of reflective tapes would be worth considering.

What paint to use on render, inside a woodstove alcove

Please see our blog post Painting the Walls around a Fireplace or Multi Fuel Stove.

Hi. I am looking for something to waterproof my trailer fiberglass roof. But it needs to be transparent as need the light to come through it . . .

We have 2 products available in clear which you could try; Britannia Aquashield Smooth which is normally for use on skylights or Rust-Oleum LeakSeal.

I have got a small ex garage which i have converted into utility room n got it plastered in the bottom corner the plaster wasn't drying due to condensation todays it come mouldy what would u recommend . . .

See our blog post: Quick & Cost-Effective Ways To Paint Over Mould

How do I paint over glass?

Please refer to our blog post: How To Paint Glass.

What do I need to paint over galvanised metal?

Our blog "How To Paint Galvanised Metal Surfaces" has details for preparing, priming and painting over galvanised metal.

Do you have any tips for painting wood that's been stained or varnished?

Yes - our blog "How To Paint Exterior Woodstained Or Varnished Surfaces" covers surface preparation, priming and finishing with Zinsser products.

How do I paint over a friable or denatured timber surface?

See our blog on How To Paint Denatured Timber.

How do you paint over uPVC?

For help on preparing, priming and finishing, see our blog "How To Paint Plastic And UPVC".

I have undecorated surfaces stained by water; how do I go about painting over them?

Our blog post "How To Paint Undecorated Water Stained Surfaces" covers this.

How do I paint over exterior surfaces stained by water?

Our blog has a how-to guide titled "How To Paint Exterior Water Stains" detailing how to prepare, prime and finish the surface properly; another guide, using water-based products, is available here: "How To Paint Over Exterior Water Stains (Water-Based Method)".

How to paint rust-stained surfaces

See our blog here: How To Paint Rust-Stained Surfaces

How to paint over PVC?

See our blog: How To Paint Over PVC

How To Paint Fletton Brick

Our blog post "How To Paint Fletton Brick" cover how to prepare and prime the surface before finishing in over 350 colours.

How to paint over nicotine stains

Our blog post (How To Paint Over Nicotine Stains (Odourless Method)) shows how to paint over nicotine stains with odourless paints.

Could you tell me what the best paint productis for interior stone walls. I need to do something with the ugly rough stone brick fireplace surround! Thanks for your help . . .

Please see information on our blog post: Painting the Walls around a Fireplace or Multi Fuel Stove

Hello, I'm looking for something to seal exernal painted garden ornaments. So basically I've painted the ornaments and I just need a top coat to protect the paint from the outside elements. Is there such a product? Thanks. . . .

We would suggest trying Rust-Oleum Crystal Clear for this.

Hi I am the Clerk to the Town Council The Council want to apply a reflective cover of paint on the front edge of an external set of stone steps a sa safety measure-would you have a suitable product? . . .

We do not have a reflective paint for this application but do have a tape which you may find suitable - Heskins Reflective Anti Slip Tape

How To Paint Brickwork . . .

See our blog post here.

How To Paint Interior Mildew Areas . . .

See our blog here for a guide on preparing, priming and painting over mildew.

How To Paint Plastisol . . .

Our blog post here explains how to properly prepare, prime and finish painting over plastisol.

Hi there, My customer has a small wood burner inside a recessed chimney breast that has been painted with ordinary emulsion and it is cracking and peeling. I know that this is partly owing to the previous painter not applying a mis . . .

Please see information regarding this on our Blog Post: Painting the Walls around a Fireplace or Multi Fuel Stove

White fire restaurant paint for fire surround please how much to please

Please refer to our blog post: Painting the Walls around a Fireplace or Multi Fuel Stove

What is your best paint to paint inside a fireplace with fireboard and plaster with a small.woodburner inside, we want a white paint if possible thank you . . .

Please refer to our Blog post: Painting the Walls around a Fireplace or Multi Fuel Stove

Hi, looking for suitable paint that I can use on the fire insulation boards behind and both sides of my wood burner in a chimney stack. Can you please advise. Regards Rob . . .

Please refer to our Blog post: Painting the Walls around a Fireplace or Multi Fuel Stove

Which product do I use to prime IKEA wardrobe doors that are laminate, before painting with farrow and ball paint ? . . .

Zinsser B-I-N is our best recommended primer for this type of laminate. Make sure the surfaces are thoroughly cleaned, Zinsser Universal Degreaser & Cleaner is a great cleaner for this type of material. Rinse off after using the Cleaner Degreaser then straight on with the B-I-N followed by your top coat.

Hi, I am having a Lidget Compton garage 6.5 x 7.5 meters floor area, erected in January the 21st I want to paint the floor as soon as possible. I have some questions. How long should i leave the concrete floor before I apply the pa . . .

402 WG Damp Proof Coating can be applied to concrete substrates providing they have a minimum 97% relative humidity reading to provide a moisture tolerant and durable high build finish. The temperature must be above 3°C during application and cure - 2 coats would be recommended

Someone has spray painted graffiti on the side of my house on the brickwork. Which product would be best suited for removal? . . .

Hydron AG4 Graffiti Remover is recommended to remove paint from porous surfaces such as brickwork.

Is Zinsser Watertite the best for walls that are wet through condensation?

Zinsser Watertite is applied to bare brick or blockwork to prevent damp coming through from behind - to reduce condensation problems on previously painted internal walls we'd recommend Coo-Var Anti-Condensation Paint

Hi I’m looking for heat resistant paint to paint behind our multi fuel burner, directly onto the fire board. Can you recommend anything please? . . .

Please see our Blog post on painting the walls around a Fireplace or Multi Fuel Stove here

I am restoring antique cast iron guttering and would like to know which one coat black metal paint you would recommend which would give the longest protection? Thanks Lucy . . .

Teamac Metalastic Black Bituminous can be applied to bare ferrous metals to provide a waterproof, weatherproof, corrosion resistant finish.

Do you Stock microtech wood worm killer .

Microtech Wood Worm Killer is not a product we currently stock and sell I'm afraid

Hi can you tell me what paint I can yes for painting fire board as one off my customer has just had a new stove fitted and the fire board is at the back of the stove on the walls... . . .

You can view our Blog post on painting the walls around a fireplace or multi-fuel stove here

price of jotun seaquantum ultra s / 20 l / light red / delivered to austria / innsbruck. regards kurt

We do not offer any form of an export service at this time so cannot provide you with a quote on this occasion.

Looking for a non slip paint to cover tiles to a an outdoor balcony

Smartkote Safekote can be applied over Smartkote Protectakote Clear Primer Treatment on glazed tiles to offer an attractive, abrasion resistant anti-slip surface.

Hi ive laid a concrete bace to a pub celar floor and require some paint that is hard Wearing and resist the beer chemical. We also have a large decking area that needs some no slip paint that is almost like a sand bace. I hope to h . . .

If the concrete already has a damp proof course then our 303 Epoxy Floor Paint applied in 2 coats would be durable and resistant to many mild forms of chemicals. Alternatively, if the concrete does not have a damp proof course then 2 coats of our 402 Damp Proof Coating would be ideal. Assuming the decking is timber and has previously been painted with a standard single pack anti-slip coating then Coo-Var Anti-Slip Acrylic Floor Paint applied in 2 coats would provide a slip resistant finish.

Which of your products should I use on a corrugated tin roof that is rusting

The existing rust would need removing by hand/power tool back down to a bare metal substrate before ensuring the surface is clean ready for painting. Applying 2 coats of Rust-Oleum Mathys Noxyde Pegarust would provide an anti-corrosive, waterproof finish.

I have a tarmac drive right up to my front door, and want to turn the part by the front door into a garden without digging up the tarmac! Is there a paint that I could use to 'paint' fake pavers over the tarmac that will be permane . . .

Rust-Oleum Tarmacoat is available in a range of standard colours and can be applied to clean, dry asphalt or tarmac. We couldn't guarantee that any of our products are permanent but if the coating is regularly inspected and any maintenance undertaken it will provide a long lasting finish.

What is the best paint for an exterior garden concrete slab path which has become slippery. I will jet was it first to make surface clean then paint the one you recommend. Colour not so important factor. Must be anti slip, last yea . . .

Smartkote Protectakote UVR would be recommended for this application. If the concrete is damp or weak then a primer coat of Duram Duraprime would be advised first.

Hi, we have 1960’s style of fireplace with what I think are ceramic tiles (hearth and surround) (brown & beige tiles) are we able to paint over these? It is still an open coal fire which is used on Christmas Day. Thanks Mary . . .

Please see our blog post on painting the wallas around a fireplace or multi-fuel stove - here

Do you do blue line paint for carparks

Rust-Oleum Tarmacoat is available in blue and suitable for line marking both internally and externally

Hi Can someone call me please i am looking to get goods from you for graffiti removal from brickwork which is heavy soiled my numner is 07597306971 . . .

We'd normally recommend Hydron AG4 Graffiti Remover for removal on brickwork

Hi, I have approximately 200m2 of Indian smooth sandstone slabbing outside which becomes dangerously slippery when wet or icy. I require an anti slip paint which is durable and clear. What would you recommend? Can a tester be suppl . . .

Smartkote Protectakote UVR can be applied to a stone substrate, is available in clear and will offer a durable anti-slip finish.

Hi am I looking for floor paint to cover old council wet room flooring, can you recommend the best paint for the job? Thanks . . .

Without knowing specifically what system had previously been used on the floor, we couldn't give any guarantees of compatibility but would recommend trialling Smartkote Safekote for this application.

Hello, Do you have v small quantity/test pots of your products available. Product of interest: Teamac top coat. Marine environment application. I would like to see if your product will work as a top coat on some steel that has alre . . .

Unfortauntely we do not offer samples of any of the products that we offer so you would need to purchase the smallest size offered online for any test areas you would like to undertake.

Where can i buy heat resistant paynt

You would buy directly through our website - available products can be found here

Please can you recommend a heat resistant paint I can use on the brick surround of my open working fireplace? Thanks . . .

Please see our blog post on painting the walls around a fireplace or multi-fuel stove here.

I am looking for a non ionic cleaner to remove a large area of graffiti along a canal in Edinburgh . Can you please give me a cost inclusive of delivery to Glasgow . Many thanks Ross Dalgleish . . .

Our graffiti removers do not contain non-ionic surfactants so couldn't recommend any product on this occasion.

Hi. We have graffiti on an unpainted untreated brick wall on the side of the garage. We have tried a graffiti remover (from Halfords) and it had no effect at all. It looks like spray paint. What remover would you recommend thanks. . . .

We'd recommend Hydron AG4 Graffifi Remover which is designed to remove graffiti from more porous or extensively vandalised surfaces.

Wanting to know what finish is best for my wood floor after sanding. Its a dining room and entrance hall 2 adults 3 x dogs and a cat!! Getting lots of use all day every day. Thank you . . .

Rust-Oleum 4900 Polycoat 2K is a clear, water-based, 2-component polyurethane topcoat for use on wood, concrete and pre-painted surfaces. It is very abrasion resistant, available in a matt or gloss finish and does not yellow. It can be used internally and externally, resists boiling water, alcohol, coffee, red wine, dilute acid and alkalis.

Do you sell a frost free clear Matt topcoat / sealant for metal

We wouldn't have anything we could recommend for this application currently.

What is the lead time for supply of the Envirograf Door Upgrade Varnish System 4m-2 ? I understand we need to call for advice first. . . .

This system is kept in stock so would be available on a range of delivery options including 3-5 Working Days and Next Working Day. If you read through the documents and are happy your doors are suitable you can make a purchase online otherwise we would recommend you speak with our technical team on 0113 245 5450 Option 2.

Hi I have a small dayboat with painted plywood seating some of which needs replacing. I will be using marine plywood and require a mid to light grey finish. It will be used in a marine environment and subjected to being sat on, equ . . .

We'd recommend 2 coats of Teamac P101 High Performance Finish directly on to bare timber to offer a very durable finish available in most standard RAL and BS Colours.

I am looking for an outdoor non slip paint to go over glazed tiles on balcony can you recommend one in light grey Regards Robert . . .

Smartkote Safekote can be used on an external balcony to provide a non-slip finish to glazed tiles following application of Smartkote Protectakote Clear Primer Treatment as an adhesion primer.

We’re quoting to paint exterior metal fire escape stair treads only. Which product is best for exterior metal? . . .

Providing the metal surface is clean, dry and free from rust you would prime them with Smartkote Protectakote 2K Metal Primer followed by 2 coats of Smartkote protectakote UVR.

hi can i paint gloss over rustins blackboard paint?

Zinsser Allcoat Exterior Gloss (Water Based) should be fine for overcoating this product.

Hi Have you got paint for metal in Matt finish. Colour ral8080

Cromadex 222 is available in a matt finish and we could offer it in a match to RAL 8080 - if you wish to order you would need to contact our sales team on 0113 245 5450 Option 1.

I am looking to have a metal splashback made for my kitchen that is about 2.3m X 0.85m this will also be situated behind my hob. I want to have it painted in a colour (to be decided) and was looking to see if a specialist heat pain . . .

Unfortauntely we currently wouldn't have anything we could recommend for this application.

Looking for a paint to cover my narrowboat fibre glass roof to try to cure leaks. If possible I would like the paint to dry so that you could touch it without getting it all over your hands. Any suggestions Area approx 30 sq metres . . .

Assuming you do not walk across the roof then GacoPro Roof Coating would offer a 20 year life expectancy with the correct amount of material applied in 2 coats. The roof would need to be clean and dry prior to application.

I have 3 manhole to paint in my driveway there are metal very unsightly with rust all over them can you recommend what type of paint to use . . .

The rust would need removing preferably by mechanical means before application of 1 coat of Smartkote Protectakote 2K Metal Primer and 2 coats of Smartkote Protectakote UVR.

I've had an extension /insulated conservatory on the back of my bungalow, where the roofs join there seems to be a leak, having great difficulty in finding exactly where it's coming from a number of things have been tried to no ava . . .

To seal a leak on external roofs we would recommend Rust-Oleum Mathys Fillcoat Fibres which is fibre reinforced and crack bridging to seal leaks and cracks instantly.

Tiling on a bitumen floor i need to level with a screen then tile what sealant screed is suitable please

Assuming the bitumen is adhesive residue (at least 97% removed) then you could prime the surface with SCHÖNOX SHP followed by SCHÖNOX HS 10 if the screed would be 10mm or less. If the substrate is purely bitumen then we wouldn't have anything we could recommend.

My bay windows are pebble dashed and seem to be the source of a leak ( small) into the extension ceiling. House is approx 90 yrs old. The pebble dash is onto lathe and plaster, I think. Which of your products do you recommend pleas . . .

Assuming you are wishing to apply something to the pebbledash on the exterior of the property, we would recommend Rust-Oleum Mathys Murfill Waterproofing Coating

The paint above my glassed in gas fireplace has discoloring. I live in a new condominium and the prior resident did not have this problem. Prior to my moving in the unit was painted. Directly above the fireplace where the wall gets . . .

Please see information on Painting the Walls around a Fireplace or Multi Fuel Stove

Hi.Looking to paint a fireplace surround and hearth that has a multi fuel insert stove installed.The surround and hearth is flagstone substance.Can this be painted and if so what paints would you recommend. Regards Ray. . . .

Please see information on Painting the Walls around a Fireplace or Multi Fuel Stove

Hello, I need to paint some outdoors concrete stairs. I would like to waterproof them and then paint over them. Could you please recommend the right sealant and paint for outdoors concrete stairs? This is for a typical outdoor entr . . .

Remmers MB 2K can be applied to a traffickable surface to provide a waterproof finish and can be overpainted.

Good morning, I am looking to paint the walls of a fireplace, which contains a wood burning stove. The walls are covered with mortar and they are 55mm away from the side of the stove. 1. My understanding of the advice on your websi . . .

Please refer to our blog post Painting the Walls around a Fireplace or Multi Fuel Stove

Dear sirs... I’m looking to paint quarry tiles in my fireplace and hearth. I have a wood burning/ multi-fuel stove in the centre. So the tiles aren’t combustible nor are they subject to flame, heat yes. Equally I don’t want t . . .

Please refer to our blog post https://www.rawlinspaints.com/blog/painting-the-walls-around-a-fireplace-or-multi-fuel-stove/

Can you advise if you have a exterior non slip coating for a commercial premises that would adhere to quarry tiles? . . .

Assuming there is not any vehicle traffic we would recommend Smartkote Protectakote UVR

Wondering if this would be suitable for a hood on a BBQ

Rust-Oleum Heat Resistant Paint 750°C would be suitable for painting the outside of the BBQ hood.

Hi, do you sell an exterior dark stain/varnish for exterior timber cladding? And if so so what colours ? dark oak, medium oak ? Regards Gary . . .

We stock Jotun Demidekk Translucent Woodstain this is available in 8 different colours.

Good morning I have got a cold room in a school kitchen that requires the existing internal wood trim painting it also has some silicon seal down the edges that require painting The unit operates between 0 and +5 degrees Can you re . . .

As long as you can raise the ambient temperature during application and cure to +8°C we would recommend Rust-Oleum Biosan Aqua Plus but please be aware the paint will not adhere to the siicon seal.

is there a Aluminum based paint for polycarbonate roof that can be painted on the out side.

Bedec Super-Flex is available in Solar Reflective White and Silver, it does not state categorically for use on polycarbonate roof panels but customers have used this product with good results.

Hi I am looking for some white silicon paint to cover a EPDM? rubber roof to reflect the sun (south facing) which is on my loft conversion, also need to repair some cracking on the harris rails so would need fibreglass mesh. Hope t . . .

We can recommend GacoPro Roof Coating to cover the EPDM roof.

For any patch repairs we would suggest Gaco Roof Tape or GacoFlex 66S Tape

Hi Please could you let me know which primer and top coat would be best to do our window sills? It's an Edwardian property so not entirely sure what the sill is constructed from. There are some cracks. The colour we want to use is . . .

Assuming the window sills are masonry, we would recommend once abraded and any loose materials are removed to fill the cracks with Rust-Oleum Mathys Elastofill.

Prime with Zinsser Bulls Eye 1-2-3 Plus

Topcoat with Zinsser AllCoat Exterior

Hi can you advise what’s the best for decking.. I have used paint with micro beads before, but looking to a to it . . .

We would recommend Smartkote Safekote which is a ready-to-use polyurethane coating that provides an attractive, abrasion resistant anti-slip surface.

I need a anti skid coating over a bridge ,which flooring is to be mild steel plates and have a very very crowded situation. please share what is the product, durability and per square meter costing, also share images and video. tha . . .

We would recommend Anti-Slip Flat Plate

For the stairs on the bridge either Anti-Slip Stair Tread Covers or Anti-Slip Stair Nosings

These options are durable and will save time in application and future maintenance.

I have a leaking swimming pool both from external and also internal. I have re-rendered with SBR waterproofing agent in the render mix but i fear that it has not succeeded in stopping the leak. What can i apply to stop the leaks pl . . .

We cannot recommend any paint coatings suitable for application on to the existing finish to seal a leak so the only system we could recommend would be the Sika 1 Waterproofing System - https://www.rawlinspaints.com/sika-1

Hi, please could you recommend a top coat paint and primer which would be suitable for painting a horse trailer which has an aluminium body. Thanks. . . .

We would recommend Rust-Oleum 3302 CombiPrimer Adhesion and Rust-Oleum CombiColor

hello is the zinseer all coat satinsuitable for the exterior of a static caravan that i am painting please ? im sure its aluminium. thank you . . .

Yes Zinsser AllCoat Exterior Satin (Water Based) is suitable for application on aluminium if previously painted. If the aluminium is bare then you would need to prime 1st with Zinsser Bulls Eye 1-2-3.

I have just purchased Gaco Pro roof paint. Does the roof need to be bone dry to apply it or can I just dry the roof with towles first. . . .

For application of GacoPro Roof Coating the substrate must be completely dry.

I need advice on which paint to use on a previously painted exterior steel beam in a domestic property please. Steel grey colour and 2 litres minimum required . . .

We would recommend either Rust-Oleum 7500 Alkythane for ease of use and if the existin coating is single pack. If the existing coating is 2 pack then we'd recommend Rust-Oleum 9200 Rust-O-Thane for a satin finish or Rust-Oleum 9600 Rust-O-Thane Polyurethane for a gloss finish.

I need a anti slip paint for a composite floor in an open top car. It's to help my feet grip whilst using the pedals. It needs to be black or transparent could you recommend a paint for me? Thanks. . . .

We would recommend Smartkote Protectakote UVR this is available in clear and a selection of colours.

I have a metal roof on a garage when it is cold it condensates then drips making it to wet to store anything in do you have a cure . . .

We would suggest priming the internal metal surfaces with Coo-Var Water Based All Metals Primer and then apply Coo-Var Anti-Condensation Paint

Can you tell what best Teamac Antifouling paint for my steel hulled fishing boat which works in seawater

For this application we would recommend the use of Metaclor Antifouling Primer followed by two coats of Teamac Antifouling D Plus

Is it possible to obtain a colour chart for Plastisol paint (coating galvanised steel) please?

All the cladding paints on our website have colour charts relevant to the specific product you are interested in purchasing.

I have made the mistake of painting the inside of my summerhouse with emulsion paint and have been told the damp is because building cannot breathe. Can you advise what product might help in removal of said paint? Many thanks Susan . . .

We can recommend Rust-Oleum Nr.1 Green Paint Stripper

Hello. I need to touch up the paintwork on my marine diesel engine. Can you advise if Rust-Oleum Combi Color is a suitable product. Thanks . . .

Rust-Oleum Combi Color is heat resistant upto 90°C (dry heat). Assuming the surface is prepared and painted correctly and engine temperatures are below this we cannot see it being a problem.

Hi There We are re-sheeting a workshop with Big 6 Fibre Cement panels and are painting these on site. The shed is in a heavily exposed rural location although only single story and low risk of impact/damage. Approx 300sqm single si . . .

Assuming this is for vertical walls we would recommend Wethertex AP77 Flexible Smooth Masonry Paint this available in many RAL and BS colours.

Is there a heat resistant paint good for a metal chimney pipe and a wood burning stove door? Thank you

You could try Rust-Oleum Heat Resistant Paint 750°C

Hi I want to paint inside the fireplace that will house a wood burning stove and would like to know if you supply a suitable paint for this purpose. If so, please could you also advise what preparation I need to do before applying . . .

Please refer to our blog post: Painting the Walls around a Fireplace or Multi Fuel Stove

Hello, I was wondering which paint I could use for a fire grate in my chimney. I would like to give it a new coating to look better. Which paint could handle flames? Thank you. . . .

Unfortunately we don't have any heat resistant paints that could withstand direct flame contact.

I have a fibreglass flat roof and the gray top coat is flaking badly,it has been for some time,my intention is to remove as much as possible and then sand down and paint with hopefully one of your products.any advice on what produc . . .

If you wish to recoat for purely aesthetic purposes, you must sand back and remove the current topcoat completely and then apply Bullet Roof GRP Roofing Topcoat. If the requirement is for waterproofing purposes, remove all loose and flaking topcoat and then prime with Bullet Roof Quick Prime followed by Bullet Roof Mono.

do you stock sherwin William's 2pac floor varnish many thanks Dave mullins

We only supply Sherwin-Williams protective and marine coatings, we assume this is from their decorative range of products which we do not offer.

Do you have eqivalent paint to Sandtex fine textured paint? In midstone or cornish cream?

We would suggest considering Rust-Oleum Mathys Murfill Quartz

i intend to paint over a previously painted garage door.(reason is to simply change color to white). existing paintwork (brown) is in reasonable condition with no peeling or rust. i will of course lightly sand the door and wash dow . . .

Assuming the garage door is steel, surfaces are clean, dry, sound and free of any contamination that may interfere with adhesion we can recommend Rust-Oleum CombiColor in the colour and finish of your choice.

Do you deliver to Flushing Cornwall? If so what is the mailing cost ? Thank you

We deliver through out the UK please see our Delivery Terms & Pricing

Hi - I have a steel garden table (described as anthracite in colour) which is rusting on the top. What is best to buy to paint it and stop the rusting please? It is a Matt finish. Thanks. . . .

We would recommend preparing the surface to a sound state and removing all rust/loose and flaking material prior to application. Degreasing with Cromadex 678 Spirit Wipe is recommended and should be carried out after any abrasion of the surface with P180. Then apply Cromadex 2100 One Pack Universal Primer followed by Cromadex 233 One Pack Air Drying Alkyd Topcoat in the colour and finish of your choice.

hi i am looking for paint to cover cladding which is at the base of the house i will need 10 gallons white exterior paint will you giive me a price pls thanks . . .

Assuming this is previously painted wooden cladding, we would suggest after preparation Wethertex OT25 Wood-Flex Satin Opaque Timber Paint.

Do you do anti slip paint for metal Thanks

Depending on the condition and level of traffic for metal floor surfaces we normally suggest Smartkote Protectakote 2K Metal Primer followed by Smartkote Protectakote UVR.

I have a new wooden garage. It has been tanalised, but has no other finish. Do you sell a coloured finish which would waterproof it? I am looking for an opaque paint, preferably in a creamy colour. Thank you. . . .

Surfaces that are to be coated must be clean and dry. Freshly impregnated wood should dry for 2-4 weeks, depending on the weather, before any coatings are applied. Remove any salt crystals that are on the surface of the wood with a brass brush and then wash the surface thoroughly with clean water.

Then apply Zanders PF59 Stain Blocking Primer Finish followed by Wethertex OT25 Wood-Flex Satin Opaque Timber Paint in the colour of your choice.

Hi. I have a chimney that’s gone rusty - needs a complete re-paint. What black paint can you recommend . Thanknyoub . . .

Ensure all rust, loose and flaking material is cleaned off, then assuming temperatures do not exceed 650°c, it is indoors or in a sheltered outdoor environment we can recommend Rust-Oleum Heat Resistant Paint 750°C

I want to re paint my extension fibreglass roof what prep is involved and the paint needed the roof is in good condition but want to maintain its integrity Regards Ed . . .

For this application we can recommend Bullet Ready Roof Kit.

In preparation for application remove all dirt, grease, dust, vegetation etc from roof surface prior to applying any product.

We recommend using a pressure washer and to ensure all loose deposits that may affect the bond of the product are removed.

Full preparation and application instructions can be found on the Technical Data Sheet in the attachement tab on the product page link above.

Can you please answer a question please. Bbq with Aluminium cookbox. I want to paint it black. Any ideas? Probably up to 260c Many thanks for your time. Regards Paul . . .

Rust-Oleum Heat Resistant Paint 750°C - Not to be used on areas subject to contact with food or flames.

Want to paint my yard floor grey, what should I use? Thanks

We'd suggest Coo-Var Anti-Slip Acrylic Floor Paint.

Which product would remove graffiti from a stone wall? Thanks

For porous substrates, such as brickwork, concrete and stone and other porous surfaces where a longer ‘dwell time’ is needed for effective removal we can recommend Hydron AG4 Graffiti Remover.

Hi, I’m looking to cover a 2m sq area of my bathroom with a clear coating to coat some recently laid vinyl flooring which is very slippy. Do you stock such a thing? Thank you . . .

For this application we would recommend TRYING Smartkote Safekote, we cannot offer any guarantees but have had success with it in the past on similar applications.

Clean well using a proprietary detergent. Allow to dry. An adhesion test is recommended prior to use.

good morning. I am looking for a product to paint onto exterior stone/concrete steps to our front door that are overhead an habitable basement entrance. I would like it to be non slip for the steps and waterproof to prevent excessi . . .

We would sugest Smartkote Protectakote UVR in the colour 'Sand'. See details of preparation/application required on the product page.

Sir I want to paint the soffits and facias on my bungalow dark grey/anthracite. They are white and in good condition. The new windows fitted are anthracite so I want the soffits and facias to match. Which paint would you recommend . . .

For this application we can recommend Zinsser AllCoat Exterior Satin (Water Based). Anthracite grey would usually be RAL 7016.

I am stripping down a wooden side gate, and need to primer / undercoat it. I have the paint for the top coat, which is a Crown Trade top coat in deep blue. This paint is oil based. Which primer / undercoat would you recommend? . . .

We would ask you to check compatability with your choice of top coat by testing on a small area first, but can suggest Teamac Wood Primer White.

Our compatible topcoat would be Teamac Marine Gloss

we are planning to paint an internal staircase at present its a red colour and made of metal with anti slip treds which of your products do you recommend . . .

Assuming the staircase's previous coatings area compatible, in sound condition and prepared for application we would recommend Rust-Oleum CombiColor Original for all areas of the staircase not walked on.

For all areas receiving foot traffic we would suggest Rust-Oleum 7200 Floorcoat PU.

Hi I’m looking for a hard wearing non slip paint in dark grey/slate for an internal staircase. Can you recommend please? . . .

Assuming the staircase is wood and in a residential home environment we would recommend Coo-Var Anti-Slip Acrylic Floor Paint.

Hi can you please advise on what products would be best for me to use, I have an engineered oak wooden floor and it’s been down for about 9 years and has lost its shine and I intend to sand it down hopefully next month. The floor . . .

Unfortunately we currently wouldn't have any coloured floor stains/varnishes we could recommend for your application.

Hi, We have a tearoom and have just sanded back solid wood table tops, applied stain and then a matt clear varnish to coat and protect but i'm thinking that i probably need a more durable and scratch free covering to protect when c . . .

If you are looking for a more durable finish for the tables we can recommend Rust-Oleum 4900 Polycoat 2K.

It is very abrasion resistant, available in a matt or gloss finish, does not yellow, can be used internally and externally, resists boiling water, alcohol, coffee, red wine, dilute acid and alkalis.

I have an asbestos garage which appears to have been painted white some years ago and looks grubby in need for some attention, my wife wants to use brown fence paint, I don’t think it would work and we should use a light colour o . . .

Assuming this is for the vertical wall sides of the garage and not the roof, we would recommend careful cleaning and preparation - see product data sheet for details (available to download from the 'Attachments' tab on the product page) and apply Thermoguard Asbestos Encapsulating Coating as directed.

Can I paint storage heater

Blackfriar Quick Drying Radiator Paint will take a temperature up to 150°C and is available in a white semi-gloss finish. As we don’t know what actual surface temperature the storage heaters will get up to we can’t say for sure if the paint will be OK on any particular storage heater, it could depend on the model, type etc. You will need to check with the manufacturer to find out what the surface temperature of their particular heater will get to during use. If it is below 150°C then Blackfriar Quick Drying Radiator Paint could be used.

Hi guys,I’m looking for a grey sealing paint for my limestone patio slabs 5ltrs can you help/provide please? . . .

Due to Limestones being a porous substrate we do not have a grey sealing paint suitable for this application.

We can recommend Sika Stone Protector as a clear sealer suitable for use on limestone.

As quality of natural stone can vary, always test a small inconspicuous area prior to full scale application.

How much liquid rubber paint do I need to cover 4.5x2.2 area

Assuming you are looking at Bullet Ready Roof Kit these come in handy packs which come with everything you need to coat 5m².

We wish to purchase kiln dried sand for our block drive preferably light coloured. Is this available to get delivered now. Thanks . . .

For this application we can recommend Sika Setting Sand, this is available for delivery.

I have noisy flat roof in my property when the heat of the day passes and the roof contracts Is there any heat resistant paint that would help? . . .

You could consider Britannia Aquashield High Build, this is available is Solar Reflective White finish.

Please see the Technical Data Sheet to check compatability with the roof substrate or call our Technical team on 0113 2455450.

Hi...the previous owner has painted the fence concrete posts with fence paint. But it wears off and looks rubbish. Rather than replace I want to paint them with something that will last and not fade as quick. What paint do you reco . . .

We would suggest one of the Zinsser AllCoat Exterior products which offer a 15 year life expectancy.

I have a built in outside seating area that is rendered, it has a steel edging under the render but the rust has one through the render and paint, is there anything you can recommend to prevent it coming through if we repaint it? T . . .

We don't believe there is anything that can be done to truely prevent these rust stains from re-appearing without stripping the render off back to the bare steel, preparing the steel, coating it with an anticorrosive system, re-rendering and then painting.

As a short term, temporary fix you could try a couple of coats of Zinsser Cover Stain before re-painting.

Hello I wanted to get hold of sherwin Williams paint iron ore for interior wood (doors) I notice you are UK stockists. Do you have any? Many thanks . . .

We only stock and supply Sherwin-Williams protective and marine coatings, not their decorative range of products.

Hi i have outside steps that lead to my flat. Currently painted white. I need a white paint to re paint these steps also they are quite slippy at the moment. Is there a non slip paint that could help thats white . . .

Assuming the previous coating is of sound condition and prepared we can recommend Coo-Var Anti-Slip Acrylic Floor Paint.

This is available in white.

Hi, My wife wants to paint a brick fireplace (open fire) do you have a paint suitable for this application in a Matt white? Kind regards Steve . . .

Please see our blog post Painting the Walls around a Fireplace or Multi Fuel Stove on the website for information regarding painting aroud a fireplace.

Need damp proofing paint for out doors

Thank you for the enquiry, I have contacted you directly for more information.

Where is my local Stockist of Cromapol

We have a trade counter in Leeds and we ship throughout mainland uk, we do not have other stockists.

Have single skin house, cement render with snowcem paint. Damp in house. Whats the most waterproof breathable paint that can go onto cement base? Thx . . .

Thank you for the enqiury, we have contacted you directly for more information.

Hi, I have 4 outdoor steps in front of my home which are made from terracotta tile. They get slippery when wet. Which adhesive anti slip tape would you recommend? Many thanks . . .

Assuming the terracotta tiles are porous, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend first priming with Heskins Primer then application of Heskins Safety-Grip Anti-Slip Tape Rolls.

I have some asbestos soffits. Which would be the best type of paint to encapsulate them?

Assuming the soffits are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Thermoguard Asbestos Encapsulating Coating.

hi, we have an Attic bedroom ceiling that needs help, tried papering it, but now peeling off after only 12 months, thought it would be best just to paint it. Not sure what type of paint would be best to put on it. Brand new roof so . . .

Thank you for the enquiry, we will need more information to assist you with a recommendation, we have contacted you directly.

Would you have an exterior weather shield paint in the colour pebble ?smooth finish to go on a rendered walk . . .

Thank you for the enquiry, assuming the rendered walls are cement based, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Wethertex AP77 Flexible Smooth Masonry Paint.

This can be mixed to many RAL and BS colours.

The only pebble we can reference would be RAL 7032 Pebble Grey.

We would recommend viewing a RAL colour chart in person to ascertain if this is suitable for your requirements.

Hi, we've spent a lot of money on epoxy flooring this year. Unfortunately, a lot of what we put down was on steel floors. The contractors told us that it would be likely that if we ran slid heavy objects across it, it would likely . . .

Thank you for the enquiry, we have contacted you directly for more information on possible preparation and pictures of the areas to be painted.

I have kitchen units that have a wood effect laminate on the the doors and front of draws what would be the best paint for me to use from your range. Thank you . . .

Assuming the laminate doors are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Matt Chalky Kitchen Cupboard.

Alternatively if a satin finish is required you could consider Technispray Kolorbond Aquatek, this is usually for spray application but can be brush or roller applied when the Technispray Kolorflow additive is also used.

Hi. Can you please recommend a product that I can coat onto the surface of the flaunching (cement) of a chimney stack to provide the best water proofing protection. Thanks . . .

Remmers Funcosil FC is a hydrophobising impregnation product in cream form, it is used to reduce water absorption on porous substrates, this could be used for this application if you are looking for a clear rather than painted finish.

I have painted my upvc front door with paint purchased from yourselves- has pre instructions on the tin. Looks fantastic very pleased. However the paint is already scratching off by the letterbox due to post I suppose. Sealant wasn . . .

Thank you for the enquiry, we have contacted you directly for more information.

I am looking for a SMALL Tin of White Fire Proof Fire-proof Masonry Paint - its for a small area so i don't to pay much - About £31 of Less . . .

Thank you for the enqiury, unfortunately we do not have a fire protection coating for application to masonry, we can offer paints for protecting timber, plasterboard and structural steels.

Hi I just did a touch up job on some rust spots on my van using Rustoleum Combicolor. Unfortunately it got rained on before it was fully dry. Will I have to take all the spoiled coat off or can I just sand it down and repaint? than . . .

Once the paint is fully dry, we would recommend sanding back the areas till they are sound and the reapplying the paint as required.

hi i have a smooth concrete drive what would i need to paint it with obviously it needs to be anti slip

Thank you for the enquiry, for the concrete driveway to be suitable to be painted it will require that a damp proof membrane is present and would need to be ground prior to application of a paint system.

If this is possible please provide the information below to [email protected]

Environment - interior or exterior
Substrate – concrete, power floated, porous? Timber or metal
Is there a damp proof membrane present
If screed applied what is it, also provide TDS if possible
Location – garage, warehouse, domestic
Condition – bare or previously painted
Exposure – foot traffic, vehicles, forklifts, chemicals
Size of area to paint
Colour required
Finish required, matt satin or gloss
Antislip?
Application- who will be applying it
Application timescale
Level of preparation prepared to undertake – grinding floor prior to application?

What's your best product for a single coat of protection on external brickwork to prevent rain penetration and yet leave the brickwork looking exactly the same after drying out? . . .

Assuming the brickwork is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Wethertex WB1 WeatherBLOCKER.

This is clear and can give protection from damp without effecting the appearance of the substrate.

Hello I have a log burning stove positioned in a corner of a shepherd hut with a metal guard behind it attached to the wall (wooden) with an air gap to protect the wall from the heat of the stove. I need a heat resistant paint to t . . .

Assuming the metal guard is not subject to temperatures over 600°C, it is clean, dry, sound and can be prepared as detailed in the technical data sheet Jotun Solvalitt could be used.

Assuming the metal guard is steel it must be blasted to SA2.5 prior to application, this paint can be mixed to many RAL and BS colours in a matt finish.

I have very slippery white tiles on my kitchen floor. Having slipped, ending up in hospital, I want to apply a non slip coating, to the surface. The tiles are approximately 250 x150mm. Please advise a suitable product you may have . . .

Assuming the tiles are glazed, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend to first prime with Smartkote Protectakote Clear Primer Treatment followed by Smartkote Safekote.

This is a bare foot friendly anti-slip paint which is available in clear, or a range of colours.

is it possible to paint over lead, the type that would be used in flashing (I think) and if so what products would be suitable . . .

Assuming the lead flashing is clean, dry and sound Zinsser Bulls Eye 1-2-3 can be used on lead, then over painted with a compatible topcoat.

Do you have a ral colour swatch which has the names in english. many thanks nick

Yes we do and they are available to purchase here.

Good Morning Do you do a product that can be painted on kitchen cabinets to make them fire retardant. They are being installed in a care home hallway and not a kitchen. . . .

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Wooden toilet seat has stains. I have sanded down what spray finish should i use

Assuming the wooden seat is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend HMG 14 Line Fleet Polyurethane Aerosol.

This is available in many RAL and BS colours or a clear finish.

Need guidance on the correct paint to cover UPVC cladding on a suspended ceiling in our bathroom please

Assuming the UPVC cladding is not subject to direct water contact, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser Bulls Eye 1-2-3 followed by 2 coats Zinsser Perma-White Interior.

This can be mixed to many RAL and BS colours in a matt or satin finish.

got a caravan roofing sheets where the plastic coating paint has bubbled and pealing at edges

Assuming the roofing sheets are plastisol, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Mathys Noxyde Pegarust.

This is available in a range of colours.

Any loose of flaking coating must be removed prior to application.

Hi, Is there a balcony paint system that can be used to add a durable surface layer on top of a coat of Evercryl? (Balcony is approx 5 x 3m, screed and previous surface made good and waterproofed for this winter with a coat of Ever . . .

We would recommend to test for compatiblity and adhesion prior to full application on previously applied paints as this is not generally suitable.

Assuming this is successful, the roof is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend KoverTek TekPur Waterproof Balcony Kit.

Hi Can you recommend a paint for exterior wooden windows please- not in great condition Thanks

By not great condition we are assuming you are referring to the existing paint and not the wood itself. After preparation and removal of all failing, loose, flaking paint, prime all bare areas with Zinsser Cover Stain and apply 2-3 coats of one of the Zinsser AllCoat Exterior Water Based range in your chosen colour and finish.

Hi, I have a listed building dated 1850 where the brickwork in the roof void is very crumbly and spalling due to previous damp and water ingress from the roof. I have now got a new roof and I am interested in stabilising the wall s . . .

Thank you for the enquiry, we have contacted you directly for more information.

Hi I have quite a bit of gloss paint on my brick walls that has been there for a few years now. Do you have any product that would remove this please? I tried brick acid before but it didn't touch it unfortunately. Thanks Shaun . . .

We can recommend Thermoguard Thermostrip PRO.

What primer is best to use on a stained staircase . Do I need to use a undercoat after . Or can I use a topcoat straight away . . .

Assuming the stained staircase is clean, dry, free from anything that will interfere with adhesion we can recommend Zinsser B-I-N as a primer.

Followed by two full coats of Zinsser Perma-White Interior, this is available in many Ral and BS colours.

Hi there, we’re after a paint for our garage door to match the front which is Chartwell green. Do you have anything to match this? Thanks . . .

Find suitable paints for garage doors in Chartwell Green in our Popular Colours category, with products from our most popular manufacturers including Rust-Oleum and Zinsser.

Assuming the garage door is steel or previously painted, dry, prepared and in sound condition we can recommend Rust-Oleum CombiColor Original.

If the door is aluminium you would need to prime first with Rust-Oleum 3302 CombiPrimer Adhesion.

These products are also available in 4,200+ NCS, RAL, and British Standard colours.

Hi there, I’m looking to renovate an old fireplace with black gloss paint. Does heat resistant spray paint exist in gloss? If not, does it exist as normal brush paint? It would be to paint over the existing stone/marble type mate . . .

Please see our blog post on Painting the Walls Around a Fireplace or Multi-Fuel Stove for assistance with this enquiry.

I want to paint brickwork and mantelpiece on my fireplace wt paint cn I ise

Please see our blog post on Painting the Walls Around a Fireplace or Multi-Fuel Stove for assistance with this enquiry.

Hi I’m wanting to screed over my decking outside and then have a resin finish application applied. Have you a product that might be suitable. I could reinforce it with mesh or use a cement board directly on the decking first. Man . . .

Assuming 18mm OSB 111 t&g sheets are screwed down over decking, we can recommend the Bullet Roof system.

You will require a coat of Bullet Roof Quick Prime followed by two coats of Bullet Roof Mono with a layer of Bullet Roof Reinforcement Matting laid on to the first coat of mono while wet.

Followed by Bullet Roof Mono Top.

If you require an antislip finish you can apply Bullet Roof DKI Quartz to the final coat of Bullet Roof Mono Top.

Hi, I’ve an old railway van we are converting. We are removing the rust from the steel work and then want to prime. Is this t the zinc primer I need? How long for delivery to BD23 5hx Thank you Lucy . . .

If you are requiring a Zinc primer you can consider Teamac Zinc Phosphate Primer.

If you would like more assistance with the project regarding options from priming through to topcoats please call Technical on 01132455450 option 2.

What product should I use to remove silver spray aerosol graffiti from my garden fence previously treated with Sadolin and Cuprinol . . .

The issue with graffiti on timber is that it is very porous and the pigments soak into the timber.

Hydron AG4 Graffiti Remover can be applied and then generally washed off with a pressure washer. It will depend how solid or soft the timber is to how much of the graffiti it can remove. It will also likely remove any Sadolin/Cuprinol product on there too.

Hi , I’ve had some paint off you in the past. I’m looking for some heat resistant paint that I can use on some projects at home, making bbq’s & out door wood burners from up cycled gas bottles. Now the paint I’ve used p . . .

Galvanized steel is suitable for high-temperature applications of up to 392 °F (200 °C). Use at temperatures above this level will result in peeling of the zinc at the intermetallic layer.

As such whatever paint you apply will also peel off with the zinc.

If the bottles were steel and not galvanised, subjected to continuous temperatures lower than 650°C and peak temperatures no higher 750°C we can recommend Rust-Oleum Heat Resistant Paint 750°C.

Hi Do you do a paint for outdoor slabs In grey?

Assuming the slabs are concrete we can recommend Coo-Var Acrylic Floor Paint, this available in flint grey.

If you require an antislip paint please see Coo-Var Anti-Slip Acrylic Floor Paint.

Smooth surfaces should be roughened first to provide a good "key" for the paint. This can be done mechanically by abrading or blasting, or chemically, using Coo-Var Acid Etch.

Looking for a charkole outside concrete paint! This is 2 use in my patio? Thanks

For application to a concrete patio we can recommend Coo-Var Acrylic Floor Paint.

If you require an antislip paint please see Coo-Var Anti-Slip Acrylic Floor Paint.

Smooth surfaces should be roughened first to provide a good "key" for the paint. This can be done mechanically by abrading or blasting, or chemically, using Coo-Var Acid Etch.

Hi. I'm looking to repaint a small fibreglass resin flat roof extension.. Can you recommend a product from your range. Thanks . . .

Assuming the roof is in sound condition we can recommend Bullet Ready Roof Kit.

Each kit covers 5m² and contains everything you will require for application.

Hi there, I purchased 5 litres of 301 industrial paint in Safety Yellow for the entrance to my flat which is concrete. I’m not sure now about the colour, would I be able to mix this with another colour to achieve something less b . . .

Yes as long as you use another 301 Industrial Paint to mix in, it will have no negative effect to the practical use of the paint.

Can you recommend a robust metal paint to overcoat some metal storage cupboards including shelves.The original powder coat has worn and chipped somewhat but is generally solid.The paint would need to include RAL light grey colour t . . .

Assuming the previous coating is of sound condition, we would recommend priming with Rust-Oleum 3333 Super Adhesion Primer and finishing with Rust-Oleum 9100 High Performance Epoxy.

This is available in many RAL or BS colours and would be very robust.

Which paint will be most suitable for painting my kitchen laminate worktop please

For this application we can recommend the Rust-Oleum Worktop Transformation Kit.

This is available in Galaxy Black or Diamond White.

Do you have a dark green corrugated asbestos board paint. If not are you able to pont me in the right direction? Regards Mike . . .

Assuming this is not intended to be applied as roof coating we would suggest Thermoguard Asbestos Encapsulating Coating.

I am looking for dark grey slabs paint

Assuming the slabs are dry, clean and free from contaminants we can recommend Coo-Var Anti-Slip Acrylic Floor Paint.

This available in various colours including grey.

What colour do you have available in the barn paint for exteriors walls

Bedec Barn Paint is available in many colours, please follow the link and press the 'choose colour' button for all available options.

Hi I'm after 5l of cuprinol decking stain in dark oak and 1l of sadolin superdec satin opaque wood protection Ral 7038. Do you have availability? . . .

We do not stock Cuprinol, but you can consider our range or excellent range of alternatives including Jotun Demidekk Decking and Garden Stain and Jotun Demidekk Ultimate.

I need to spray or paint an external metal faced door (already finished white) which has plastic trims, and a plastic service meter box, finished finish to be Matt ral 7016 Anthracite Grey. Do you have anything suitable.please. Reg . . .

We would recommend priming all substrates first with Zinsser Bulls Eye 1-2-3 then finishing with Zinsser AllCoat Exterior (Water Based).

This is available in many Ral and BS colours and in matt, satin or gloss finishes.

Hi I am looking for a heat resistant paint to paint the brick work behind and around my stove in white..can you advise please. Regards Wendy . . .

For advice and products to paint around a stove please see our blog post Painting the Walls around a Fireplace or Multi Fuel Stove.

Hi I need heavy duty wood floor oil or varnish .. I have barber shop that why I need heavy duty

Assuming the floor is sound and prepared inline with the guidance in the Technical Data Sheet we can recommend Blackfriar Heavy Duty Varnish.

Hi Im looking for a heat resistant paint to use on the exterior of my pot belly fireplace in my dining area. What do you recommend? . . .

For advice and product recommendations regarding Painting the Walls around a Fireplace or Multi Fuel Stove, please see the blog post on our website.

I would like to paint my metal garden furniture.. which paint would do the best jiob

Assuming the furniture is in sound condition and abraded to remove as much corrosion as possible we can recommend Rust-Oleum CombiColor Original.

Hello, I've used blackfriar exterior preserver recently, it was fine but appears to be off sale (a little concerning why..?) and could have had a little more brown colour in it so open to alternatives you recommend? It's just for g . . .

Assuming the timber is in sound condition and prepared to the guidance within the Techhnical Data Sheet as an alternative you can consider Jotun Demidekk Decking and Garden Stain.

This is available with 10 colour options in a matt finish.

Help pls. looking for anthracite grey paint outdoor gloss. do you stock this pls

We offer a Water Based or Solvent Based exterior gloss both available in RAL 7016 Anthracite Grey in the Zinsser AllCoat range, see HERE.

I have a firewall behind a log burner which needs painting but I dont need a large amount, it is to cover only 12 tiles but the burner gets very hot so I would need it for heat over 500 degrees maybe. I want it in grey or silver co . . .

Please see our blog post on Painting the Walls Around a Fireplace or Multi-Fuel Stove for assistance with this enquiry.

Hi Our multi-fuel stove is causing the emulsion paint behind it to give off fumes. We have heat resistant plasterboard on the wall but we need something to cover the emulsion. Hope you can advise. Sarah . . .

Please see our blog post on Painting the Walls Around a Fireplace or Multi-Fuel Stove for assistance with this enquiry.

Hi I have an external wall which was cover by a fence but have removed the fence and the wall is pretty rough. So was after a textured paint as I don't fancy plastering it. Is there anything you recommend. I can forward pictures if . . .

Assuming the wall is clean and sound we can recommend Wethertex HBS Flex-Coat Hi-Build Coating.

If there is any algae or fungicidal growth we can recommend the use of Wethertex C10 Multi-Surface Fungicidal Wash prior to painting.

If the wall has an unstable surface we would recommend the use of Wethertex ST1 Quick Dry Stabilising Primer prior to Wethertex HBS Flex-Coat Hi-Build Coating.

I have a large farm shed which is built with concrete blocks, probably 45 years ago, however when the rain is driven by the wind it comes through the wall, l am looking for a exterior paint that will stop this problem in a grey col . . .

Assuming the wall is clean, dry and sound we can recommend Rust-Oleum Mathys Murfill Waterproofing Coating.

This is available in many Ral and BS colours.

New or unpainted substrates must be treated first with Rust-Oleum Mathys Primer 44 HS.

Hi I am looking for a paint that will cover rust without too much preparation it’s for an old metal outdoor table. Your guidance would be appreciated. . . .

For this application we would recommend manually or mechanically remove of as much rust as possible then apply Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion.

Followed by two coats of Rust-Oleum CombiColor Original.

This is available in many Ral and BS colours.

Thankyou for your earlier reply. One more question please. Do I need a primer, undercoat for Zinsser all coat upvc paint. Kind regards. Martin. . . .

Zinsser AllCoat Exterior (Water Based) in satin or gloss finishes can be applied directly to aged UPVC.

Zinsser AllCoat Exterior Matt (Water Based) this will require a coat of Zinsser Bulls Eye 1-2-3 prior to application.

New UPVC must be wiped down with a solvent wipe using methylated spirits prior to application.

Hello I looking for garage concrete floor primer

Thank you for the enquiry, to assist you we will require more information on the project, please contact our Technical team on 0113 2455450 option 2.

Hi i am looking for ronseal deck stain country oak do you have this?

We do not stock Ronseal but can offer Jotun Demidekk Decking and Garden Stain as a great alternative.

This is availabel with 10 colour options.

Morning. Can u please tell me if u do a zinsser all coat exterior in dark grey please. Kind. Regards.

Yes, Zinsser AllCoat Exterior is available in many Ral and BS colours, including dark grey.

This is available in matt, satin or gloss in water and solvent based.

I’m looking for a decent garage door paint in navy blue. Can you recommend one please and a primer/undercoat if needed? . . .

Assuming the garage door is steel, dry, clean and abraded prior to application we can recommend Rust-Oleum CombiColor Original.

This is available in many Ral and BS colours in a satin or gloss finish.

If the door is galvanised or aluminium we recommend spot priming bare areas with Rust-Oleum 3302 CombiPrimer Adhesion prior to application.

If the door is timber we can recommend Rust-Oleum CombiColor Multi-Surface.

I would just like to enquire as to which would be the best kind of anti slip paint to paint the slabs in our back garden. Kind Regards.Alan. . . .

Assuming the slabs are concrete, clean, dry and sound we can recommend Coo-Var Anti-Slip Acrylic Floor Paint.

This is available in 7 colours and a clear finish.

Do you have a paint that can paint a worktop ( standard MDF with a grey plastic coating) and tiles? White Matt. I don’t quite need 2.5 litre so a bit smaller maybe? . . .

For this application we can recommend the Rust-Oleum Worktop Transformation Kit.

This is available in Galaxy Black and Diamond White finishes and comes with all the preparation equipment.

For the tiles assuming you are looking for a white finish we can recommend Rust-Oleum Tile Transformation Kit.

What is the best product to use on my 4ft cement rendered pond thanks

Assuming you are looking for a paint to line the pond we can recommend Teamac Chlorvar Chlorinated Rubber Paint.

For application a thinned down first coat (15%) with Chlorvar thinners, followed by a further two coats are required.

Then leave pond empty for 2 weeks before refilling.

Hi dear i need a paint of roof slate tiles grey.white spot on the roof tiles need to clean up have tried but not going.want to do paint. . . .

For this application assuming the tiles have a thorough clean with a pressure washer and any moss is removed with AMW fungicidal Wash we can recommend Rust-Oleum Mathys Dac Hydro Plus.

For slate tiles you will need to prime with Primer 44HS or Pegafix prior to application.

Can I add Owatrol paint conditioner in Teamac gloss top coat?

As Teamac Gloss is solvent based the Oawtrol Paint Conditioner is not compatable with this product.

Hi. I have a cement rendered rain drip strip ( 2.5m in length ) which had been angled horizontally thus the rain dosent drip from the leading edge. I was thinking about applying a bead of sealant to this edge to allow tge rain to d . . .

Although nothing can be guaranteed due to the nature of the project/application we would suggest trying Bullet Mega Mastic.

Hello I am looking for a metal primer that will prime galvanised critall windows. Years ago I used red oxide which was an error as the paint has now flaked off the galvenised metal. So going to give the job another try but need a p . . .

Tikkurila Temaprime EE followed by Tikkurila Temalac ML 90.

Do you sale black storage heater paint. If so, how much would it cost for a small can please?

Assuming you are looking for a matt finish we can suggest Rust-Oleum Heat Resistant Paint 750°C. This can withstand sustained temperatures upto 650°c.

As we don’t know what actual surface temperature the storage heaters will get up to we can’t say for sure if the paint will be OK on any particular storage heater, it could depend on the model, type etc. You will need to check with the manufacturer to find out what the surface temperature of their particular heater will get to during use.

I have painted a design in a children's fibreglass outdoor bench in aqua gloss paints. It is for a children's playground so will get some wear and tear. What is the best cleat protective varnish I could use on it? . . .

We would suggest a small compatability test prior to full application with the aqua gloss paints. Subject to this we can recommend Smartkote Protectakote UVR Smooth.

I require paint to cover my outdoor concrete flags in my yard. After having work done on the exterior walls of my house they have become marked and I am unable to remove stains. I was thinking about a grey something that would not . . .

Assuming the concrete slabs are clean, dry, sound and free from anything that can effect adhesion we can recommend Coo-Var Acrylic Floor Paint.

This is available in Flint Grey.

I am looking for paint that i can use on the wall behind my wood burning stove. Preferably grey

Please see our blog post on the website, Painting the Walls around a Fireplace or Multi Fuel Stove for recommendations for this application.

Have you got any primer paint for garage door grey

Assuming the garage door is mild steel, dry, sound and free from anything that can effect adhesion we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion.

Hi I am looking at painting a ships container (20` x8` x8`) it is situated on a seafront. It will be sandblasted before I paint it. So I would need a primer and a top coat. It will then need to be painted with Leyland Pliolite Maso . . .

For this application we would not recommend applying a masonry paint to a steel container.

As you are sand blasting the container we can recommend Rust-Oleum Mathys Noxyde for this application, on steel no additional primer is required and would provide a far longer lasting solution than Leyland masonry paint pliolite or otherwise.

What paint to use inside my fireplace? Old house built 1919. Was a coal burning fireplace. Now will soon be gas logs. . . .

Please see the blog post on our website with details and recommendations for this application. Painting the Walls around a Fireplace or Multi Fuel Stove.

Hi I'm stripping a galvanised steal shed, if got it back to the metal . Their are a few rust spots on it. Could you please help I dont know what to do next. Iv had to use a little white spirit to remove some old tar from it. Not su . . .

For this application we can recommend Rust-Oleum Mathys Noxyde. This can be applied directly after cleaning, is available in White and leaves a satin finish.

To apply the required 2 coats to 35m² you would need approximately 35kg.

Hello. I’m painting some tiles and going to place them in the fireplace behind the multifuel stove. I’m concerned that I need a heat resistant top coat/varnish for them if they’re going behind the stove. Can you recommend a s . . .

Please see the blog post on our website detailing options and products for this application.

Painting the Walls around a Fireplace or Multi Fuel Stove.

I had a new wet room rough finish (Anti Slip) lino floor fitted in our wet room just over a year ago and quite a lot of the colour has already worn off, is there a long lasting paint that can be used to paint over it all. Regards M . . .

There is nothing we have that we can guarantee will work but other customers in the past have used Smartkote Safekote successfully for this type of application so may be worth a try.

What spray paint can I use to repeat my cooker doors? Silver epoxy appliance paint.

Unfortunately we do not have a product we can recommend for this application at this time.

I am trying to order Sika pave fix plus. Its said its discontinued is there an alternative please

As an alternative we can recommend Sika FastFix All Weather.

This is a ready-to-use, self-setting paving jointing compound with Active Resin Technology for advanced durability. It sets hard and will not wash out, whilst remaining water permeable.

do you sell paint for out side doors

Yes we do, if you are looking to paint an exterior previously painted timber or aged UPVC door we recommend Zinsser AllCoat Exterior (Water Based).

what hammered paints can be brushed on please

Assuming you are looking to paint a suitably prepared steel surface we can recommend Coo-Var Hammercote Hammered Finish.

Hi I’m looking for a stencil of an arrow for marking on a road one way system Thanks james

See Rust-Oleum Stencils

Waterproof paint for wooden boat keel

For this application assuming the hull is dry, sound and prepared we can recommend two coats of the Teamac Metaclor Antifouling Primer.

Followed by either Teamac Antifouling D Plus if you require an anti-foul or Teamac Chlorvar Chlorinated Rubber Paint if not.

Hi could you please tell me if you do a floor paint for a walk in shower Thankyou

For this application we can recommend Smartkote Safekote.

This is bare foot safe antislip floor paint and is available in clear or coloured options.

Depending on the substrate the paint is to be applied to, a primer may be required. Please see the Technical Data Sheet in the attachment tab on the product page to confirm this or call our Technical team on 0113 2455450 option 2.

Hi I made a pit fire with Bbq top grill out of a 45 gallon drum, I sprayed it on the outside with a heat resistant paint spray I bought in my local DIY store. The fire has set for upto 3 weeks I took it outside last night and lite . . .

Assuming the drum is not going to exceed heats of 650°c and is stripped to bare steel prior to application we can recommend Rust-Oleum Heat Resistant Paint 750°C.

Hi, I’m after a white wall paint that’s suitable for a pub kitchen, could you advise? Many thanks

For this application we can recommend Rust-Oleum Biosan Aqua Plus.

I need exterior Colour paint to go on wood. Half ltr. Yellow, Blue, orange. Purple. Pink. Indigo. Can you help? . . .

Assuming the wood is clean, dry, sound and abraded we can recommend Zinsser Cover Stain followed by Zinsser Allcoat Exterior Water Based.

This is available in many RAL and BS colours in matt, satin or gloss finishes.

Hi i bought few tins off u last year floor paint but do u sell the grit that goes in it seperatley i did buy it with the paint but need more grit but not more paint thanks . . .

We stock many Anti-slip additives but we'd need to know which floor paint you bought to advise on the correct one to use. Please call our Technical Team where we should be able to find your previous order and advise - 0113 2455450 (option 2).

I am the caretaker at a primary school. I have been working hard preparing the school for when lockdown finishes. I have two jobs left and need good paints for this . I need a white paint for galvanised steel pergola supports where . . .

Assuming the galvanised steel supports are clean, dry, sound we can recommend Rust-Oleum 3302 CombiPrimer Adhesion followed by two coats of Rust-Oleum CombiColor Original.

For the steel handrails, assuming they are sound, dry and abraded we can recommend Rust-Oleum CombiColor Original.

If any areas of the rails are rusty we would recommend priming with Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion prior to application.

I’m looking for a suitable paint for my outside wood fire , its made from gas tanks ?

Assuming the tanks are steel, dry, sound and not subject consistent temperatures exceeding 650°c we can recommend Rust-Oleum Heat Resistant Paint 750°C. Note this paint is not suitable for areas subject to food contact or direct contact with flames.

Hi I’m looking for a 400ml orange heat resistant spray can to spray a lambretta exhaust do you have any thanks . . .

Unfortunately we do not have a suitable paint in an orange finish but can recommend Rust-Oleum Heat Resistant Paint 750°C.

This is available in black or aluminium.

Hi I need a floor paint for some large red floor tile,s they have a mortar grout and are in an outbuilding converted utility room Do I need a primer first? Doesn’t need to be the best option just a good one . . .

Assuming the tiles are glazed, clean, dry and sound we can recommend Smartkote Protectakote Clear Primer Treatment followed by Smartkote Protectakote UVR Smooth, subject to a test of adhesion prior to full application.

hi, I'm looking for something I can put on the feet of some wooden garden benches, to stop them rotting..? could I paint the epoxy on and make boots or any other suggestions. thanks . . .

We would suggest something simple such as Teamac Metalastic Black Bituminous.

Hi There,l am looking for paint to cover 6 roller shutter doors. They are galvanized and haven't been painted since being installed. Brown colored if possible. Cheers . . .

Assuming the galvanised steel is dry, sound and free from anything that can effect adhesion we can recommend Rust-Oleum 3302 CombiPrimer Adhesion followed by Rust-Oleum CombiColor Original or for larger projects/surface areas Rust-Oleum 3202 Galvinoleum Primer followed by Rust-Oleum 7500 Alkythane.

The flexibility of the coating allows it to cope better with the opening and shutting movement of the doors.

Hi what paint would you recommend for painting a brush finish render (under bell)which has a few fine cracks in places,also does it need cleaning and priming? What product should I use to clean a pebble dash render and possibly re- . . .

Assuming the surface is sound, dry and cleaned with Rust-Oleum Mathys ND14 Cleaner Degreaser we can recommend Rust-Oleum Mathys Primer 44 HS followed by Rust-Oleum Mathys Murfill Waterproofing Coating.

Hi do you have a heat reflective paint to apply to glass windows that can be removed easily ? Peter

For this application we can recommend Coo-Var White Glass Shading.

This is a seasonal water based paste for dilution which slowly wears away with weather. Ideal to block out excess light and heat helping to reduce interior temperatures.

Hi. Can you recommend a product to paint over a balcony which has bitumen on it.. I would like a matt finish in black. Something that will adhere to bitumen and allow foot traffic. Thank you Mark . . .

Assuming no additional waterproofing is required we can recommend Rust-Oleum Tarmacoat.

For application to bitumen the first coat should be applied thinned 20% with clean water.

Hi I am looking to recoat my fibreglass flat roof I was looking at the aquashield paint would this be my best option Thanks Abby . . .

Assuming the roof is dry, sound, free of moss, lichen and debris by brushing or power washing and treated with a Fungicidal Wash we can recommend Britannia Aquashield High Build.

I require a price on 10litre 20 litre industrial floor paint in classic dark grey (anthracite)

See HMG Factory Floor Paint, available in any colour (inlcuding RAL 7016 Anthracite Grey) and comes in 5lt or 20lt tin sizes.

Our conrete path and steps have been painted with Valspar masonry paint. We now see every footprint on the path. Is there any sealer that would prevent this? Or will wear and tear solve the problem? . . .

After cleaning, you could try applying the clear version of Coo-Var Anti-Slip Acrylic Floor Paint over the top to see if this helps.

Can you recommend a primer for a radiator with a few rust spots. White. 750ml

Assuming the radiator is clean, dry, sound and any rust areas are abraded back to clean, bright steel we can recommend Blackfriar Multi-Surface Primer followed by Blackfriar Quick Drying Radiator Paint.

What paint do you recommend for solar reflective for a lead flat roof to prevent heat build up?

Assuming the lead is clean, sound and free from anything that can effect adhesion we can recommend GacoPro Roof Coating.

This is available in solar reflective white.

Hi there, I’m looking to paint the ceramic tiles around my pond. Could you please advise if you have a product for me. Regards Pete . . .

Assuming the tiles are clean, dry, sound and abraded, we can recommend Smartkote Protectakote UVR Smooth or Smartkote Protectakote UVR.

Both of these will require a coat of Smartkote Protectakote Clear Primer Treatment prior to application.

Do you do a paint for asphalt in a dark grey thank you

Assuming the asphalt is dry and in sound condition we can recommend Rust-Oleum Mathys Pegasol Quartz.

This is available in Dark Grey and can go directly onto cleaned and prepared asphalt.

We would like to paint over the marble effect inner fire surround,is this possible and if so what would we use? Thank you for your help . . .

Please see our blog post Painting the Walls around a Fireplace or Multi Fuel Stove for this application.

I have a pillar where I had an extension done inside this part of wall gets damp I have sealed the wall with damp seal paint and then painted over but after awhile paint bubbles up can you recommend a sealer and which paint to use . . .

There could be a number of reasons for this happening, the first thing we would suggest is fixing the source of the damp. We have a number of articles on our blog regarding damp issues which you can see HERE.

Does Wethertex AP77 require a primer? And will it adhere to an existing external masonry paint, or would it require stripping first? . . .

For application to new or bare surfaces AP77 should be diluted 10-50% with clean water depending on the substrate for a primer coat. AP77 can be applied over existing paint, assuming the previous coating is compatible, sound, dry and well adhered. Testing for adhesion on a small area prior to application is recommend.

Hi I am looking for an outdoor concrete paint for paving slabs in my garden that I can use a jet wash on without the paint lifting. Thanks Val . . .

Assuming the jet washer is used on a low pressure and carefully we can recommend Coo-Var Acrylic Floor Paint.

On the unpainted surface the first coat of Coo-Var Acrylic Floor Paint should be thinned 5% with clean water.

Hello, I’m looking to paint my internal stairs with non slip paint but would like to knows if the finish would be too rough for bare feet. Could you advise please? Thank you . . .

Assuming the stair treads are dry, sound and abraded we can recommend Smartkote Safekote. This is a barefoot safe antislip floor paint available in many colours and a clear option.

This would be suitable for a multitude of surfaces, we would recommend consulting the product information to determine if a primer is required.

I have recently purchase new UPVC patio doors in white as I could not afford the£1000 price difference for coloured doors. I wish to paint them blue & have been advised rustoleum is the best paint to use for this.. I would pre . . .

We can only recommend Rust-Oleum CombiColor Multi-Surface be applied to AGED UPVC, assuming all oil, grease and all other surface contaminations by cleaning in combination with appropriate detergents (e.g. Rust-Oleum Pre-Paint Cleaner). The surface must be abraded, clean and dry during application.

Hi I want to paint my old weathered roof slate tiles what would you suggest

Assuming the tiles are clean, sound, dry and free from moss we can recommend Primer 44HS followed by Rust-Oleum Mathys Dac Hydro Plus. This is available with 6 colour options including Slate.

Hi, I own a narrowboat which i am looking to repaint. The build up is of timber and has then been overlaid with a vinyl covering then previously painted. What would you recommend to cover the roof. There are two main issues to cons . . .

Assuming you can remove the vinyl, we can recommend Teamac High Performance Marine Gloss which could be applied directly to timber.

This is available in many RAL and BS colours.

I am looking for a long lasting paint to apply to some shipping containers and the framework to some modular buildings. What product would you recommend. We are in west wales, 7 miles from the coast but the air is still quite salty . . .

Assuming the containers are dry, sound and any rust is removed prior to application we can recommend Rust-Oleum Mathys Noxyde.

Please see the Technical Data Sheet for application and preparation details.

And enquiry regarding painting a fibreglass roof, roof is done and painted with sealant paint, but its a dull grey, do you do any other colours to put on but not black . . .

Thank you for the enquiry, we have contacted you directly for more information.

I am restoring a classic car. Your combi colour looks ideal for the undernrath. However i would like to apply a stone chip over the top or leave the combicolour as the primrbprotection but concrrned when the body is painted any ove . . .

Assuming the Rust-Oleum CombiColor Original is fully cured we would recommend you test for compatibility and adhesion with any coating you wish to apply of the top on a small area prior to full application.

We would not recommend applying a two pack paint over this paint and would suggest masking this area off during spray application.

I have existing timber windows with sikkens cetol wood stain in ebony. I would like to paint them an off white colour. Which of your products would be best for primer? Mid and top coats? Satin finish preferred . Also will need wood . . .

Assuming the stain previously used is not silicone based, the timber frames are clean, dry, sound and prepared as detailed in the Technical data sheet we can recommend Zanders PF59 Stain Blocking Primer Finish.

This can then be over painted with Wethertex OT25 Wood-Flex Satin Opaque Timber Paint which is available in many RAL and BS colours.

now that botonox is discontinued what is an alternative to paint the outside of a house

As an alternative to Butonox or Demidekk Ultimate we can recommend Remmers Rofalin Acrylic.

We have contacted you directly for more information.

Dear Sirs, We have a site located at Liverpool docks with substantial steel structures. As you can appreciate, these require regular painting because of the corrosive saline environment. We are looking to source a paint capable of . . .

Assuming the steel work is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Mathys Noxyde.

This is available in a range of standard and RAL colours.

It is suitable for upto a C5-M environment.

I have a 3sq metre external balcony with asbestos cement 12”x12” tiles fitted when my property was built in 1975. They are sound. I would like to seal the surface. What should I use and how much is the product? Thanks. . . .

Thank you for the enquiry, we have contacted you directly for more information.

Hello I would like some paint to cover the bottom two course of bricks on my bungalow. The brick face and mortar joints are starting to deteriorate so I would like to repaint and then paint black. I'm hoping for a look like the old . . .

Assuming this has been previously painted in a bituminous product, sound, dry and abraded we can recommend Teamac Metalastic Black Bituminous.

We are working on a project where the bottom of a key klamp roof stepover (steps with handrails to enable people to walk over duct obstructions on a flat roof) is in contact, probably nearly all the time, with ponding water on a fl . . .

Assuming the galvanised steel is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Jotun Jotamastic Smart Pack HB.

I have recently sealed and painted my concrete garage floor and now need to apply a clear sealant to ensure the paint surface does not flake or disturb when I drive a car in and out of the garage. What product do you suggest I use . . .

Thank you for the enquiry, we have contacted you directly for more information

Hi, I am interested in using rustoleum combi colour to paint a van can you please tell which colour code matches nato green . . .

Thank you for the enquiry, these and many paints are mixed to industry standard RAL and BS paint codes, as stated on the website we show a representation of the colours on the website, but these can look difference on various devices.

So we recommend to view a RAL or BS colour chart in person to ascertain colour suitability.

These can be purchased here.

I am looking for an undercoat for an exterior wall of old breeze blocks (a garden wall) that I want to paint with exterior paint to brighten up a grey wall. I want something to seal it from damp coming through as it is a soil retai . . .

Thank you for the enquiry, unfortunately we do not have a paint suitable for this application, but you could consider the Sika 1 Waterproofing System to tank the wall first.

Good afternoon, I am looking for a WHITE paint that I can use to paint my outdoor concrete patio slabs. Thank you . . .

Assuming these are bare, exterior patio type paving slabs, then after cleaning we would suggest Coo-Var Anti-Slip Acrylic Floor Paint.

Hi im looking for a heat resistant tile paint for my hearth not a black preferably silver and ideally a brush on rather than a spray paint can you advise me which one is suitable many thanks . . .

Please see our blog post on Painting the Walls Around a Fireplace or Multi-Fuel Stove for assistance with this enquiry.

Hello I need some help finding paint / spray I can use on glass / ceramic. I have a wardrobe which has glass / ceramic doors.. please help . . .

Assuming the glass and ceramic wardrobe doors are clean, dry, degreased prior to application we can recommend Zinsser Bulls Eye 1-2-3 followed by Zinsser Perma-white Interior.

This is available in many RAL and BS colours.

Do you stock a white paint that I could use to paint the ceramic tiles behind my Rayburn?

Please see our blog post on Painting the Walls Around a Fireplace or Multi-Fuel Stove for assistance with this enquiry.

I've recently had some block paving laid on my drive it's nearly 80sqm. I would like some advice on how I can protect and save it from weeding using your products and giving it longer lifetime. . . .

To reduce the frequency of weeding the block paved driveway we can recommend Sika Setting Sand. This is a moisture curing jointing compound and resists weeds and ants.

Are your marine paints suitable to apply to fiberglass fish pond

Yes some are, assuming the fibre glass is clean, dry, sound and abraded, we can recommend Teamac Metaclor Antifouling Primer followed Teamac Chlorvar Chlorinated Rubber.

The paint needs to be left 14 days prior to submersion.

Hello Is the Zinsser All Coat suitable for brush painting a UPVC conservatory, if so what colours are available and what is the cost per tin please ? many thanks Paul . . .

Assuming the UPVC is aged, clean, dry and sound we can recommend Zinsser Allcoat Waterbased. For Satin or Gloss finishes no primer is required.

If you are looking for a matt finish you must prime first with Zinsser Bulls Eye 1-2-3.

This is available in many RAL and BS colours and the pricing is on the website.

Hi I have previously used Rustoleum CombiColor on my garage door and outdoor furniture. Would I need to repaint with the same paint or are there other paints you would recommend. Thanks . . .

We recommend consulting the Technical Data Sheet of what ever product you are wishing to over paint the combicolor with for compatability.

Assuming the previous layer of combicolour is dry, clean, sound and abraded prior to application we can recommend another coat of Rust-Oleum Combicolor Original.

Hi, I'm looking for a non slip white paint or interior stairs, can you recommend any? Thanks

Assuming the stairs are clean, dry, sound and you require a paint that is also easy to clean we can recommend Smartkote Safekote. Please see the Technical Data Sheet regarding substrates and if a primer is required for the projects application.

hi I need some anti slip paint for brick steps and York stone steps. It needs to be textured and long lasting in yellow please, can you tell me what I need? Thanks Nick . . .

Assuming the steps are clean, dry and sound we can recommend Coo-Var Antislip Acrylic Floor Paint.

What paint can you suggest for my black cast iron BBQ. Kind regards Nick

Assuming the bbq is clean, dry,sound and not subject to temperatures of 600°C, we can recommend Blackfriar High-Heat Resistant Paint.

Hi Rust-Oleum 5300 Epoxyshield Maxx Reference 5342.5 Planning to use this product to finish my concrete garage floor once treated with Sika Primer and Sika 131 Level Latex Ultra Only concern is whether the gloss finish might be too . . .

Assuming the floor does not have any liquid on it, it should not be slippery. If required an Epoxyshield Antislip Additive can be added during application.

Do you have a colour chart for your zinsser upvc paint?

Zinssser Allcoat Exterior Waterbased can be mixed to many RAL and BS colours, these can be viewed on colour chart on the product page.

Do you do a non slip coating that goes over fibreglass

Assuming the fibre glass is cleaned with solvent wipe with Xylene, dry and abraded we can recommend Smartkote UVR.

Hello We are looking for a durable exterior grey paint for a concrete staircase outside a block of flats What is your best product for this high traffic exterior situation? Newby and Son Decorating . . .

Assuming the steps are dry, clean and sound we can recommend Smartkote Protectakote UVR. Please see the Technical Data Sheet to determine if the substrate requires a primer.

Hi, I have a 30 year old motor home and I need to repaint the roof. The old paint has come off in places revealing clean aluminium underneath. Forums talk highly of combi colour paint to use here so could I ask which one would be b . . .

Assuming the aluminium roof is clean, dry, sound and abraded we can recommend GacoPro Roof Coating for this application.

I have a sloping polycarbonate roof with a few small leaks, what would you suggest to waterproof it? I assume it will need cleaning, sanding and priming and then top coating, but I am unsure which products would be suitable for the . . .

Assuming the roof is sound, dry and cleaned with a fungicidal wash prior to application we can recommend Britannia Aquashield Eco.

Do you find my anti slip.paint for the tunnel on a narrow boat

We stock many antislip paints, please consult the Technical Data Sheet to confirm compatability with the narrow boat's substrate and if a primer is required. Assuming the surface is clean, dry and sound we can recommend Teamac Suregrip Deck paint.

Hi im trying to find the best paint to put down on a concrete floor that is durable and does not come of when raining is swimming pool paint the best for this any ideas. Would be appreciated . . .

Assuming the concrete floor is sound, dry and clean we can recommend Smartkote Safekote for this application. This is a barefoot friendly antislip paint available in clear and coloured options. Please check the Technical Data Sheet for preparation details for specific substrates.

Hi, I'm restoring an old navy vessel, I'm looking for a clear gloss varnish or lacquer to cover and protect a polished aluminium wheelhouse. What do you recommend? Thanks. . . .

Assuming the aluminium is dry, sound and clean we can recommend Teamac Mordant Solution (T Wash) followed by Teamac High Performance Marine Gloss in clear finish.

Hi I am trying to choose a paint to use on exterior concrete window sills that can be RAL colour coded. I have previously tried some and they are getting discoloured when water sits on it for too long, can you advise a decent produ . . .

Assuming the concrete window sills are clean, dry and sound we can recommend Teamac Chlorvar Chlorinated Rubber for this application.

On concrete a primer coat must be applied with 10% Chlorvar thinners.

This is available in many RAL and BS colours.

Can I paint a wooden apex roof ( bird table ) with bitumen p

Yes, for this application assuming the timber is clean, dry and sound we can recommend Teamac Metalastic Black Bituminous.

Can I use a bitumen sealant ( black jack ) on a pitched roof.

Assuming the substrate is compatable as stated in the Technical Data sheet, such as felt, timber or metal, Everbuild 901 Black Bitumen Paint can be used on a pitched roof.

I want heat resistant undercoat paint and same for metallic silver topcoat, it’s for pine fireplace

Please see our blog post Home Painting the Walls around a Fireplace or Multi Fuel Stove, for suggestions and recommendations.

do you have an OXFORD BLUE METAL GARAGE DOOR coating that primes rust also .

Assuming the garage doors are steel, clean, dry and as such rust is removed as possible prior to application we can recommend Rust-Oleum Combicolor Original.

This is available in many RAL and BS colours.

It can be applied directly to de rusted steel but we would recommend for added protection to prime with Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion prior to application.

I'm looking for a decent floor tile pI t for my residential kitchen. Has to be hard wearing and easy to clean. Also relatively quick drying (say 24 hours or so) A light grey, pebble sort of colour. Is this something you can help wi . . .

Assuming the tiles are glazed, sound, and dry we can recommend Rust-Oleum 3333 Super Adhesion Primer followed by Rust-Oleum 9200 Rust-O-Thane.

This is available in many RAL and BS colours.

Hi, Do you sell a clear coating that i could paint over my existing Dulux Weathershield exterior paint to make washing birds mess easier to clean off. Thanks Mike Hawtin . . .

Assuming the previously painted wall is dry, clean and sound we can recommend Hydron Nu-Guard AG. This is an anti grafiti coating that will also make bird mess easier to remove.

Looking at your range of thermal paints I wonder if there is anything of this type that could be applied to a conservatory roof to help with the heat and cold problems associated with this kind of structure. Would appreciate your t . . .

Assuming you are looking to paint the exterior of the polycarbonate roof panels, they are clean, dry and sound we can recommend Britannia Aquashield Eco. This is available in a solar reflective white and may help to reduce temperatures but will not make it any warmer.

Hi, I am looking for a paint that would be suitable to go over a wet floor shower area. I am not in a position to redo the bathroom of the house I have recently purchased so want a temporary solution to revamp the wet room until I . . .

Assuming the floor substrate is clean, dry and sound we can recommend Smartkote Safekote. This is a bare foot friendly antislip paint available in many colours and a clear option. Please see the Technical Data Sheet for Preparation and Application details including if a primer is required for the projects substrate. Assuming the wall tiles are ceramic and not exposed to direct water contact from the shower, once prepared we can recommend Zinsser Bulls Eye 1-2-3 followed by Zinsser Perma-white interior. This is available in many RAL and BS colours.

Hi, I have a powder coated aluminium front door that I wish to paint. What product do you recommend? Regards, George. . . .

Assuming the door is clean, dry and abraded we can recommend Rust-Oleum 3302 CombiPrimer Adhesion followed by Rust-Oleum CombiColor Original. This is available in many RAL or BS colours.

I have bought some Rust-Oleum 3302 primer. Could you tell me if I paint the whole item with one coat or where there is bare aluminium it needs more that one coat. The paint has lifted in some places and is sound in others. Many tha . . .

Assuming the substrate and existing paint is compatible, has been cleaned, abraded and any loose or peeling material is removed you can use Rust-Oleum 3302 CombiPrimer Adhesion to prime only the bare areas before application of a topcoat such as Rust-Oleum Combicolor Original.

have a kemper system gutter that I need to modify and wish to then re-seal and re waterproof. The bonding substrate I need will ideally work with Galvanised steel, aluminium and the existing Kemper surface. What do you think might . . .

Assuming the substrates are clean, dry and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum Mathys Fillcoat or Rust-Oleum Mathys Fillcoat Fibres if any areas with cracks upto 2mm.

I wish to treat the external timber on a newly built oak framed oak clad building. The oak is currently green and has a high moisture content at the moment. Do I need to wait for it to dry/season before treating? . . .

The preservers such as Sikagard Wood Preserver can be applied to damp timbers, we would advise to allow a period of drying for wood with a high moisture content.

I need to paint some already painted gates in black. I want to use combicolour black satin, do I need to prime them or should I just use two coats of combi colour ? Many thanks Andy . . .

Assuming the previous coating is compatible, dry, sound and prepared then Rust-Oleum Combicolor original can be applied. We would recommend applying a small test area prior to full application to confirm compatibility with the existing coating.

Hi, I am looking for a paint that I can use on my Aga, it’s a solid fuel Aga and is already painted but it needs doing again. Can you recommend a good paint please? I would like Grey but as a second option I would be happy with c . . .

We currently have no paints we could offer for this application due to the required heat resistance.

Are there any storage heater paint that can be coloured matched to dulux brilliant white satinwood paint. . . .

Assuming the storage heater is dry, clean, prepared and not subject to temperatures over 90°C we can recommend Rust-Oleum CombiColor Original.

This is available in many RAL and BS colours.

If it is below 90°C then Rust-Oleum CombiColor Original could be used.

Good morning, I need some help choosing the right kind of paint for spray painting internal wooden decoration pieces. The colours I am after are black, white and some varnish. Preferably that which can be used in an airgun. Could y . . .

Assuming the timber is clean, dry and sound we can recommend Mathys Fassicoat. This is suitable for spray application, does not require a primer and is available in many RAL and BS colours. For use as a sprayable varnish we can recommend Rust-Oleum 7500 Alkythane.

Hi, The legs on our radio mast where they are secured into the concrete base are going rusty, I'm looking for suitable paint or anti rust solution to try and make good, any ideas please ? . . .

Assuming the legs are steel, sound, dry and the rust is removed prior to application we can recommend Rust-Oleum 769/780 Damp-Proof Rust Primer followed by Rust-Oleum 7500 Alkythane.

I want to paint over some old oak windows and porch that have turned black. I am told that the black will come through the paint and I am led to believe that is (at least in part) because it is acidic. You have products that act as . . .

This black staining can be caused by ferrous fittings, nails or screws corroding and reacting with the tannic acid in the timber.

Assuming the timber is clean, dry, sound and prepared we can recommend Zinsser Peel Stop followed by Zinsser Cover Stain top coated with Zinsser AllCoat Exterior (Water Based).

On horizontal surfaces such as window sills or heavily exposed areas we would recommend 3 coats of Zinsser AllCoat Exterior Matt (Water Based).

The Zinsser Allcoat is available in 4,000+ RAL, NCS, and British Standard colours, including BS 630 French Grey, with a choice of matt, satin or gloss finishes.

Good morning I have a utility room and the roof has a plastic sheet roof , it’s very hot in the summer is there a paint that can be put on it to stop it help cool the room . . .

Assuming the roof is polycarbonate, clean, dry and sound we can recommend Britannia Aquashield Eco applied to the exterior. This is available in solar reflective white.

Please be aware that applying paint to a clear surface, brush strokes may be visible through the substrate.

Hiya am after a liquid flat roof system. Its onto osb 3 t and g boards. What would be best? Thanks Lee

Assuming the roof is clean, dry and sound we can recommend the Bullet Roof Mono System. The Technical Data Sheet and Installation Guide in the attachment tab contain preparation/application instructions and primer requirements for all substrates.

Hi ,could you please tell me which paint I need to order for plastisol cladding,reason for painting is colour change only also do I need to apply a primer first as original coating is in good condition, regards Ian . . .

Assuming the plastisol is dry, sound and clean we can recommend Rust-Oleum Mathys Metal Cladding Topcoat. If there are any areas of bare metal we recommend applying Rust-Oleum Mathys Metal Cladding Primer prior to application.

Morning . I'm looking for paint suitable for a timber house . External wood. Do you have this in stock and what colour ? . . .

Assuming the timber is clean, dry, sound and prepared we can recommend Wethertex OT25 Wood-Flex Satin Opaque Timber Paint. This is available in many RAL and BS colours. If the timber is bare Zanders PF59 Stain Blocking Primer Finish primer will be required before application.

Hello Can you match a colour to a Land Rover paint code (LRC 670 Coniston Green)?

Unfortunately we cannot mix to an Automotive paint code. Please see the RAL and BS colour options on the product page to find a suitable match.

Which is the best value drive paint for domestic use.Approx 52 sq mtrs. I am 80 so don't need long garauntee! I will apply it. . . .

Assuming the driveway is tarmac or concrete, clean, dry and sound we can recommend Hydron Mona-Guard Revive.

For 52m² you will require 26 litres per coat. On very porous substrates two coats may be required.

I'm after some epoxy garage floor paint (21m2). The concrete has been down for about 30 years and is a little dusty, it looks to have had some small spills of oil at some point. Can you recommend a primer and top coat, colour eithe . . .

Assuming garage floor is only subject to foot and light vehicle traffic, clean, dry and prepared as detailed in the Technical Data Sheet we can recommend 403 Oil Tolerant Primer followed by 303 Epoxy floor paint.

For the steel assuming it is clean, dry, sound and the primer used is compatible we can recommend Rust-Oleum CombiColor Original.

This is available in many RAL and BS colours in a satin or gloss finish.

Do you ship to the United States?

Unfortunately we do not currently offer an exporting service.

Good morning, Do you have a dark grey paint for tarmac ? Regards Keith.

We have two options for you assuming the tarmac is clean, dry and sound we can recommend Rust-Oleum Tarmacoat, this is available in a light or mid grey.

Or Hydron Mona-Guard Revive in black.

Unfortunately we do not have a dark grey option.

We have a 2 burner cooker on our boat. The wood at the side has started to blacken Is there any thing we can do to stop it . . .

Unfortunately we do not have a product for this application we would recommend either remove the wood, move the stove or line with a stainless steel sheet.

Hi there I have a patio that is tarmac, can i paint over it but with a light colour as the black is too hot when sun is on it . . .

Assuming the tarmac is dry, clean and sound we can recommend Rust-Oleum Tarmacoat. This is available in a range of colours.

What is best product you have to treat a lugarde spruce summerhouse.l intend to treat before erecting, but don’t want paint to affect interlocking sections with first treatment. Rgds David Caddick . . .

For this application assuming the timber is clean, dry, sound and you are looking for a clear wood preserver to apply before painting we can recommend Sikagard Wood Preserver.

This should be over painted for external use.

Hi. Is it possible to use the multi surface paint on glass? Thanks

Assuming the glass is clean, dry and free from anything that may effect adhesion we can recommend Zinsser Bulls Eye 1-2-3 followed by Zinsser Allcoat Exterior (waterbased).

This is available in many RAL and BS colour in a matt, satin or gloss finish.

Please be aware that painting painting on glass brusg strokes may remain visible.

I'm looking for Red, blue, green and yellow paint to repaint a wooden fence around play equipment in a school. So although it wont be climbed on it needs to be safe in case a child decides to lick it. It is a possiblity as its a sp . . .

We do not stock a paint suitable for ingestion.

What colours does paint come in to paint lamanated floor thanks

We currently wouldn’t have any products we would recommend for application on to a laminate floor.

Our barn conversion is next to a large field that occasionally floods. As the end wall of our house is the boundary, what can I “paint” the lower wall with to stop water coming into the house as the Flood water rises up the wal . . .

Assuming the substrate is clean, dry, sound and any previous coating is abraded prior to application we can recommend Teamac Metalastic Black Bituminous.

I need 5 litres of white solar reflective paint for polycarbonate roof. Which would you recommend please? Carol . . .

Assuming the roof is clean, dry, sound and free from anything that can affect adhesion we can recommend Britannia Aquashield Eco.

Looking for a Zinnser product for an exterior slate floor tile. Perhaps you could advise what product you would recommend. Thank you. Irwin Houston . . .

Assuming the tiles are clean, dry and sound we can recommend Smartkote Protectakote Clear Primer Treatment followed by Smartkote Safekote.

Do you have a colour chart for rustoleum spray paints

The colours for this product can be found on the product page, unfortunately we do not have any printed colours available to send out.

Please see Rust-Oleum Hard Hat Topcoat.

Hi Is there a paint available that would be suitable to paint over an existing non-slip floor in a wetroom? Many thanks Brendan . . .

Assuming the floor is clean, dry, sound and compatible we can recommend Smartkote Safekote. This is available in clear and coloured options. Please check substrate primer requirements in the Technical Data Sheet.

I am looking for a locker paint for my narrow boat engine locker, needs to be rustproof, water proof. Please can you advise on product and price. Many thanks . . .

Assuming the locker is steel, clean, dry, sound and free from anything that can effect adhesion we can recommend Teamac Bilge Paint. If any areas are bare metal they must be primed with Teamac Zinc Phosphate Metal Primer.

What paint would you suggest to paint the walls of a roofed pool house? They are brick walls, above the water, and have been painted before but I don’t know what paint was used. I’d appreciate a response as soon as possible ple . . .

Assuming the previously painted walls are clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Zinsser Perma-white Interior for this application.

This is available in many RAL and BS colours.

Hi ia have a couple of 20ft containers that are wind and watertight but are showing signs of corrosion on the roofs - what water proofing roofing paint would you suggest i use? . . .

Assuming the containers are clean, dry, derusted and prepared as detailed in the Technical Data Sheet we can recommend Bullet Roof Epoxy Primer AC followed by Bullet Roof Mono.

Could you recommend a paint suitable for woodwork (i.e. door, cupboard & window) in bathroom which is prone to high humidity, steam and getting wet? . . .

Assuming the woodwork is clean, dry, sound and not in direct contact with water we can recommend Zinsser Cover Stain followed by Zinsser Perma-white Interior.

Do you do a paint suitable for galvanized metal ? Just an 8x4 sheet i've fitted to a combine harvester Would need to be mid to dark green (John Deere green) . . .

Assuming the galvanised metal is clean, dry and sound we can recommend Rust-Oleum 3302 CombiPrimer Adhesion followed by Rust-Oleum CombiColor Original. This is available in many RAL and BS colours in a satin or gloss finish.

Good afternoon Grateful if you could advise the best paint for a galvanised motorbike garage please. Many thanks Ted . . .

Assuming the galvanized garage is clean, dry, sound and you are looking to paint it for a change of colour we can recommend Rust-Oleum Mathys Metal Cladding Primer followed by Rust-Oleum Mathys Metal Cladding Topcoat. If any areas are a roof and pitched we can recommend Rust-Oleum Noxyde Pegarust.

Hi there I’m looking to paint my marble fireplace. Can you suggest what type of paint I should buy? Many thanks . . .

Please see our blog post on the website, Painting the Walls around a Fireplace or Multi Fuel Stove for details and product recommendations for this application.

I want to paint my fireplace white. It has a wooden surround and marble hearth and a brass metal strip. We have a stove there. What would be the best paint to use. Thanks. . . .

Please see our blog post on the website, Painting the Walls around a Fireplace or Multi Fuel Stove for details and product recommendations for this application.

Dear, In my industrial installation I`ve got a gas turbine metal outoing exhaust pipe that reaches 400 degrees Celsius. I would like to apply a paint in the outer part of this exhaust pipe in order to guarantee that the temperature . . .

We do have heat resistant paints such as Rust-Oleum Heat Resistant Paint 750°C, but not a paint that can reduce temperatures for this application.

Can i paint work surfaces with one coat paint, and can you recomend make .

Assuming the worksurfaces are a laminate we can recommend Rust-Oleum Worktop Transformation Kit for this application. Preparation and application details can be found in the technical data sheet, but this will take two coats.

Hi Do you have a breatheable paint suitable for cellar walls Thanks

Assuming the cellar wall are of a compatible substrate as detailed in the Technical Data Sheet, sound, dry and clean we can recommend Zinsser Grade 1. This is available in many RAL and BS colours.

Two questions re Tractor Enamel, what primer to you recommend for use on Land-Rover aluminium body (cant see a particular one on the website) I have used the TOR Zinc in the past, but the TOR top coat didn't bond to it very well. W . . .

Assuming the glavanized steel is clean, dry and sound we can recommend Zinsser Bulls Eye 1-2-3 as a primer prior to application of Tor Tractor Enamel. Tor Quick Drying Red Oxide Primer is not recommended to be thinned as it can make VOC non compliant.

I’m looking for a roof paint to cover a polycarbonate conservatory roof. The roof is getting old, but is sturdy. I’m looking for a product to waterproof and seal. What product would you recommend? Thanks - Ben . . .

Assuming the roof is clean, dry and sound we can recommend Britannia Aquashield Eco for this application.

Hi I am look for a high humidity paint for an indoor swimming pool room walls/cilings

Assuming the walls are clean, dry and sound we can recommend Zinsser Bulls Eye 1-2-3 followed by Zinsser Perma-White Interior. This is available in many RAL and BS colours.

Hi there. I’m hoping you can help. We’ve a tiled kitchen floor which is quite frankly hideous. We were thinking of painting it. I know it’s not ideal. I have seen Rust-Oleum rock solid Home as a suggestion. But not sure if in . . .

Assuming the tiles are clean, dry and sound we can recommend Rust-Oleum 3333 Super Adhesion Primer followed by Rust-Oleum 9200 Rust-O-Thane. This is available in many RAL and BS colours in a satin finish.

Have a small white fibreglass dinghy, needs a repaint on the outside, just wondering what paint to use, just to tidy her up, don't want anything too expensive . . .

Assuming the fibreglass is clean, dry and sound we can recommend Teamac Marine Undercoat followed by Teamac Marine Gloss.

This is available in many RAL and BS colours.

Im wanting to try a polyurethane paint on a plywood piece of furniture. Am I better painting a colour in a normal paint then using a clear polyurethane or using a coloured polyurethane and could you advise a good product Thanks . . .

Assuming the plywood is clean, dry and sound we can recommend Teamac High Performance Polyurethane Topcoat as a direct to timber option with a coloured finish.

This is available in many RAL and BS colours and a clear option.

If you are looking for a clear finish to overcoat a previous coating, subject to testing for compatibility prior to full application we can recommend Rust-Oleum 4900 Polycoat 2K.

Dear Sir I am thinking of painting our campervan roof. It was a white van and the paint is peeling off in places. I have seen your product on line with other people using it on vw campers. My question is do you match colours? The c . . .

We can mix some paints to RAL and BS colours but at this time we cannot mix to an automotive paint code.

My belling mastercook with 4 doors needs repainting after 18 years. I would like to know whether you have heat resistant paints for cookers please. Thank you. . . .

Unfortunately we currently have no product to recommend for this application.

Looking for heat resistant paint for a stove What colours are available???

Assuming the stove is clean, dry, sound and not in direct contact with flames or exposed to temperatures over 650°C we can recommend Rust-Oleum Heat Resistant Paint 750°C. This is available in black or silver.

Could you advice me on a cream/white paint suitable for my fire surround which is dark wood at the minute. Thank you for your time . . .

Please see the blog post Painting the Walls around a Fireplace or Multi Fuel Stove for details and recommendations for this application.

I have 15 square meters of marine ply covering my veranda. Which none slip pain and quantity,would you recommend ..must be none stop Would like terracotta . . .

Assuming the marine ply is clean, dry and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum 7200 Floorcoat PU. This is available in many RAL and BS colours. For an antislip finish add Rust-Oleum Non-Skid Additive NS 100.

We have a wall opposite the windows in kitchen, which gets condensation with water running down wall. We have extraction from cooker and windows open when cooking. Current paint Dulux kitchen plus leaves smears on wiping down. Curr . . .

Assuming you are looking for a paint suitable for high humidity areas, the walls are clean, dry and sound we can recommend Zinsser Perma-white Interior. This is available in many RAL and BS colours in a matt or satin finish. This paint is also scuff and scrub resistant.

Hi do you make a liquid rubber paint suitable for sealing a Motorhome roof

Assuming the roof substrate is clean, dry, sound and compatable as listed in the Techncial Data Sheet we can recommend GacoPro Roof Coating for this application.

I have SS Gas stove. I want color the same with Green color. Please suggest heat as well as corrosion resistance paint . . .

Unfortunately we do not have a product we can recommend for this application.

Hi looking to do my kitchen worktop and floor looking for epoxy resin pigment and resin to do this if you can hflp me pick best one if it kit with the type i need thanks . . .

Assuming the kitchen worktops are laminate, clean dry and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum Worktop Transformation Kit. To assist you further with the floor we will require more information, please call our Technical Team on 0113 2544550 option 2.

Hi.. Do you guys have interior paint for a boiler. Heat paint. Or something I can use to paint boiler inside? . . .

Unfortunately we do not have a product we can recommend for this application.

Hi, I am hoping you can help. Do you sell any water based paints suitable for metal/mild steel and in a large range of colours? (exterior & interior use) Thanks, Graham . . .

Assuming the steel is clean, dry and sound we can recommend Bradite One Can for this application. This is available in many RAL and BS colours, in an eggshell finish.

I’m looking for a hard wearing sealer 2 pack if possible clear for a bathroom floor tiles

Assuming you require a bare foot friendly floor paint we can recommend Smartkote Safekote. This is availble in a clear option. Please see the Technical data sheet for substrate and primer requirements.

Good Morning I have a flat roof which has been treated with I think some sort of fibreglass membrane to stop it from leaking unfortunately it still leaks in certain places I would like to apply one of your treatments to the roof to . . .

Assuming the roof is clean, dry and sound we can recommend the Bullet Roof Mono System for this application.

Preparation, application and primer requirements are in the Technical Data Sheet this can be found in the attachment tab on the product page.

Need to seal a corrugated metal roof on a garage, can it be sealed with a liquid treatment ?

Assuming the metal roof is clean, dry and prepared as detailed in the Technical Data Sheet we can recommend Britannia Zinc Phosphate Metal Primer followed by Britannia Aquashield High Build.

Hi Ive an old metal ship’s bench with plenty of rust but no “damage” from it that I’m keen to paint for a seaside garden. Ideally light grey (the original colour) matt or satin. I’d be very grateful for you advice on the . . .

Assuming the bench is clean, dry and rust is removed prior to application we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by 3 coats of Rust-Oleum CombiColor Original. This is available in many RAL and BS colours in a satin or gloss finish.

Hi I'm after some sort of invisible spray that you can detect under a uva light because someone keeps trying to break into my post box o live in apartment and all letter boxes are at bottom so need some sort of spray can use that c . . .

Unfortunately we do not have a product for this applicaton.

I'm trying to buy car calipers covers and I will need to paint them. My understanding is the heat that will occur can be hotter than a car engine. Will your paint support these high tempetures? . . .

Assuming the caliper covers are metal, clean, dry, prepared as detailed in the technical data sheet and not subject to temperature over 650°C we can recommend Rust-Oleum Heat Resistant Paint 750°C. This is available in aluminium or black.

Hi I'm looking for a bath coating paint system. Is this something you stock or are able to advise on?

Unfortunately we do not have aproduct for this application.

I’m looking to paint my patio slabs which paint can I use. I have riven slabs & want a matt finish Thank you . . .

Assuming the slabs are clean, dry and sound we can recommend Rust-Oleum Tarmacoat.This is available in a matt finish and a selection of colours.

Hi Iv just had a large part of my garden decked in wanting to know what the best product would be to paint/treat it. Also the describe leads straight out from my back door and having 3 kids something with none slip would be needed. . . .

Assuming the timber is clean, dry and sound we can recommend Smartkote Safekote for this application.

This is a barefoot friendly antislip paint in a range of colours or a clear finish.

Please see the Technical Data Sheet for preparation, application and primer requirements of the substrate.

I am looking for a heat resistant, frosted type paint to paint over an outdoor light, the actual glass, to dim the brightness. The light gets approximately 100 to 120 degrees, but it's on for 9 - 10 hours....do you have anything th . . .

Unfortunately we do not have a product for this application.

Do you stock floor paint for painting over a laminate floor? Have found 3v3 in b and q but only in cream, grey and white thanks. . . .

Unfortunately we do not have a product for this application.

Hi I need to purchase a 2.5ltr tin of hardener ( part b ) for intershield 300 primer is this somthing you could supply please. Kind regards Paul . . .

Yes we can, a price has been emailed to you directly.

Hi .... I’m looking for a clear roof paint for asbestos slates. Ideally a good thick bitumus type consistency so it will fill cracks in slates. Thanks for your help David . . .

Asssuming the asbestos slates are clean, dry and sound we can recommend Britianna Aquashield Eco for this application. Unfortunately this is not available in a clear option but white, black or grey.

What is the best paint for electric storage heaters

We currently have jotun 2 pack paint on our deck and stantion poles, deck has treadmaster so the current paint is not a deck paint with grit in. It's not a gloss finish either. I'd like to keep the same colour but I want a single p . . .

Unfortunately we do not have a product for this application.

Hi, I am looking for a coating for a concrete driveway, part of which has small areas of standing water in heavy rain. The concrete has been sealed. Would you recommend chlorinated rubber or any other product? Thanks Richard . . .

Assuming the dryway is clean, dry and sound we can recommend Hydron Mona-Guard Revive for this application. It is available in black and red.

I want to paint my garage floor. It has been levelled with Stopgap 300 levelling compound. Double garage approx 25 square metres. Which of your paint products should i use and will the floor have to be primed first? Thanks . . .

Assuming you have checked the screed applied is suitable to be painted, it is clean, dry and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum Epoxyshield Garage Floor Coating Kit.

This comes with everything needed to prepare and paint the floor.

What is the best wet room floor paint

Assuming the floor is clean, dry, sound and you are looking for an antislip paint we can recommend Smartkote Safekote.

Do you stock a BROWN bitumen paint or could you recommend a company that does. It’s for base of my wood shed... bottom 3 tongue and groove to shield against snow and potential rotting of wood in the winter. It’s got to be Brown . . .

No all our Bitumen paint such as Teamac Metalastic Black Bituminous is black.

I have a concrete bbq which has started to crack, one of the cracks is about 3cm wide and 25cm long, in a vertical crack. Do you have anything that I can use to bond this back together. The bbq is about 17 years old. Thanks in adva . . .

Unfortunately we do not have a product for this application.

Hi, I’m looking to give my static caravan a make over and hoping you could recommend a make of paint that will be most suitable for the job. It is metal cladding that I’m pretty sure is aluminium. Existing paint is tired lookin . . .

Assuming the metal cladding is clean, dry and sound, existing paint is well adhered and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum Mathys Metal Cladding Topcoat.

I have some aluminium gutters which need repainting. There is some old paint which is starting to flake in places. Some areas are also pitted. How should I prepare the gutters and what should I paint them with? . . .

Assuming you are looking to paint the exterior of the gutters, any previous coating must be abraded back to a sound, well adhered substrate, cleaned and degreased prior to application.

We can recommend Rust-Oleum 3302 CombiPrimer Adhesion followed by Rust-Oleum CombiColor Original.

This is available in many RAL and BS colours in a gloos or satin finish.

I've cut the handles off a huge enamel dish as it wouldn't fit into the oven. I'm left with four rings of raw steel which I want to paint. I don't want to use spray. Can you advice . . .

Unfortunately we do not have a product to recommend for this application.

Hello I need to repaint our Koi pond it was built 30 year ago still in good condition it as been painted with a black waterbased paint several time some small cracks now sealed. the pond is 4 Feet deep and 15 feet diameter. Can you . . .

Assuming the pond is built of a compatable substrate such as concrete, it is clean, dry, sound and prepared as detailed in the Technical Data Sheet, we can recommend Teamac Chlorvar Chlorinated Rubber Paint.

This is available in many RAL and BS colours in a gloss finish but please note the coating must be left 14 days to fully cure before filling the pond again.

Hi can you use your external masonry paint to paint fibre board cladding, I’m after a blue grey colour. I’ve heard you should use 100% acrylic paint Thanks Kalvin . . .

Assuming these are fibre cement cladding, they are clean ,dry and sound we can recommend Wethertex AP77 Flexible Smooth Masonry Paint. The first coat thinned to aid penetration.

I need 25 litres of black paint direct to steel corrugated roof. Ideally paint whick doesn't require priming. . . .

Assuming the steel is clean, dry and sound and you are looking for a bitumen based paint we can recommend Eagle All Weather Roof Coat.

Hi I am looking to paint my Aluminium powder coated patio doors ( 1800mm x 1800mm approx) outside only in white, aerosol spray, can please advise me about quantity and process. Kind Regards David . . .

Assuming the doors are clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum 3302 CombiPrimer Adhesion and Rust-Oleum CombiColor Original Aerosols.

Hi, I have terracotta quarry kitchen floor tiles and I want to paint them. What primer, paint and sealant do you recommend? There are ad o many types I'm a bit confused which would be the best. Many thanks, . . .

Assuming the tiles are clean dry and sound we can recommend Smartkote Safekote for an antislip finish or Smartkote Protectakote UVR Smooth. Substrate and primer requirements can be found in the Technical Data Sheet. These are available in a range of colours and a clear option.

I have a newly rendered external wall to my property and I am looking for a white or light grey anti graffiti paint for this location. Would you advise what paint and quantities i should purchase. Need about 80m2 . . .

Assuming the wall is clean, dry and sound we can recommend Hydron Nu-Guard AG, this is available a range of colours, a clear option and a semi-matt finish.

Coverage of this is usually a single coat at 8m²/litre so 10lt would be required for 80m² but this would depend on the final chosen colour and the colour you are overcoating.

Good afternoon, Could you advise me as to the best paint for a coastal property in France please. In addition to conditions near the sea the wooden shutters will also be exposed to high temperatures and would need to be tinted to R . . .

Assuming the timber is bare, clean, dry and sound we can recommend Zinnser Cover Stain followed by Zinsser Allcoat Exterior Water Based. This is available in matt, satin or gloss finishes in many Ral and BS colours. For this application we woud recommend 2 or 3 coats.

I'm looking for a recommended paint for an external precast concrete stairs ...it has very little foot traffic but its quite near the sea (300 meters) and it could get some sea spray. . . .

Assuming the concrete steps are clean, sound, dry and prepared as detailed in the Technical Data we can recommend Coo-var Antislip floor paint which is available in a range of colours.

Hi, I’m wanting to spray paint my kitchen cabinets and wondering if you have a durable paint/ primer that would be almost scratch resistance . . .

Assuming the kitchen cabinets are a laminate, clean, dry and sound we can recommend Zinsser Bulls Eye 1-2-3 followed by Zinsser Perma-White Interior.

This is a scrub and scuff resistant paint and is available in many RAL and BS colours in a matt or satin finish.

I’m looking to use a penetrating epoxy to seal my wooden shed, then paint over with a coloured paint is this possible? Kind regards . . .

We do not stock any penetrating epoxy paints for this use, but if you require a wood preserver we can recommend Sikagard Universal 5 Star Wood Treatment.

Then assuming the shed is clean, dry and sound we can recommend Wethertex OT25 Wood-Flex Satin Opaque Timber Paint. This is available in many RAL and BS colours.

Any bare timber should be primed with Zanders PF59 Stain Blocking Primer Finish prior to application.

I am wanting to paint the brick surround to my fireplace black. Can you advise which paint would be suitable please. . . .

Please see our blog post Painting the Walls around a Fireplace or Multi Fuel Stove for details and recommended products for this application.

We have some untreated wooden pine gates that will be used for a driveway. I want to paint them battleship grey but ensure the best weather protection. Can you recommend the best type of primer and paint to use please Thanks Scott . . .

Assuming the timber is clean, dry and sound we can recommend Zinsser Cover Stain followed by two coats of Zinnser Allcoat Exterior Water Based. This is available in many RAL and BS colours in a matt, satin or gloss finish.

Hi . I am looking for paint for interior window frame and door. It’s currently brown PVC I have. What would you recommend . I would like to paint it white Thanks Kathleen . . .

Assuming the window frame is UPVC, aged, clean, dry and sound we can recommend Zinnser Allcoat Exterior Water Based. This in available in many RAL and BS colours in a matt, satin or gloss finish.

Hi there, I’m looking for a clear non glossy clear top coat suitable for a metal garage door. Do you have any suitable products? . . .

Assuming the garage doors are previously painted with a well adhered paint, is clean, dry and sound we can recommend Rust-Oleum 4900 Polycoat 2K. This is available in a matt or gloss finish.

I need an anticlimb product for an epdm shed roof. Can you help?

Assuming the roof is flat, clean, dry and sound we can recommend Coo-Var Vandalene Anti Climb Paint. Application is best in thin coats.

can i paint flat slate roof tiles with masonry paint as advised by BnQ store wolverhampton. The tiles are on a canopy that covers my front door and stretches along the length of the house. They are not like normal roof tiles but ve . . .

Assuming the slate tiles are clean dry and sound we can recommend Rust-Oleum Mathys Dac Hydro Plus.

This is suitable for slate roof tiles as long as they are first primed with Rust-Oleum Mathys Primer 44 HS.

Please carry out a test prior to application to ensure compatibility, adhesion and appearance.

Hello, I have a hummingbird feeder with metal perches that get very hot in the summer. Is your paint safe for thus purpose and is it available in a small quantity, say a trial size? . . .

Unfortunately we do not have an animal safe paint to recommend for this application.

What type of paint to use on walls around wood burning stove? . . .

Our blog post "Painting the Walls around a Fireplace or Multi Fuel Stove" lists several paint systems depending on your requirements.

What paint to use on rusted metal?

Rust-Oleum 7500 Alkythane can be used to paint over rusted metal in over 350 colours, but be sure to read the relevant data sheets and/or our blog post regarding surface preparation, cleaning and priming beforehand using Rust-Oleum 769 Damp-Proof Primer.

What paint to use on upvc door? . . .

Our blog post, How To Paint Plastic And UPVC, details how to clean and prepare surfaces using Zinsser Bulls Eye 1-2-3 prior to Zinsser Perma-White Interior (for interior jobs) or Zinsser Allcoat Exterior Satin & Gloss (for exterior work), both available in over 350 colours. Be sure to read carefully the steps on cleaning the surface and preparation for maximum adhesion.

What paint to use on upvc windows? . . .

Can you paint stainless steel? . . .

Yes, please refer to our blog post How to Paint Stainless Steel for application and our recommended products.

Can you paint over varnish? . . .

Our blog posts below details how to paint over varnished surfaces, and the products to use.

Can you paint upvc windows? . . .

Yes; see our blog post, How To Paint Plastic And UPVC, for details how to clean and prepare surfaces prior to finishing in over 350 colours.

Can you paint over rust . . .

See our blog post That Moment When You Realise You Can Paint Over Rust for full details on preparing rusted surfaces prior to finishing in over 350 colours.

Can you paint galvanized steel . . .

See our blog post How to Paint Galvanised Metal for preparing and finishing new, weathered, and previously-painted galvanised steel surfaces.

The post has our recommended products to use and details how to overcome problems such as very shiny and smooth new surfaces that are difficult to adhere to, and surface contaminants such as oils, greases, residues, etc.

Can you paint upvc doors . . .

Can you paint pvc doors . . .

Our blog post, How To Paint Over PVC, details how to clean and prepare surfaces using Zinsser Bulls Eye 1-2-3 prior to Zinsser Perma-White Interior (for interior jobs) or Zinsser AllCoat Exterior Satin/Gloss (for exterior work), both available in over 350 colours. Be sure to read carefully the steps on cleaning the surface and preparation for maximum adhesion.

Can you paint a upvc door . . .

Our blog post, How To Paint Plastic And UPVC, details how to clean and prepare surfaces using Zinsser Bulls Eye 1-2-3 prior to Zinsser Perma-White Interior (for interior jobs) or Zinsser Allcoat Exterior Satin & Gloss (for exterior work), both available in over 4,000 colours including Chartwell Green and RAL 7016 Anthracite Grey. Be sure to read carefully the steps on cleaning the surface and preparation for maximum adhesion.

We also have uPVC Painting Kits with the correct amounts of Kolorbond and preparation products for painting uPVC, PVC, and composite surfaces such as doors and windows, with pack sizes dependant on the scale of the job. These are also available in 2,400+ RAL, NCS, and British Standard colours, including Chartwell Green and RAL 7016 Anthracite Grey.

Can you paint upvc . . .

Can you paint kitchen worktops . . .

Yes - the Rust-Oleum Worktop Transformation Kit is a revolutionary do-it-yourself coating that enables you to easily and affordably transform your worn or damaged worktops into beautiful and durable new counter tops. Can be applied over a weekend!

Can stainless steel be painted . . .

Yes, please refer to our blog post How to Paint Stainless Steel for application and our recommended products.

Can you paint pvc window frames . . .

Can you paint over mould . . .

Be aware that rising damp is often misdiagnosed as mould and requires a more extensive solution – see our guide on Treating Rising Damp.

Can you paint upvc window frames . . .

Can you paint over limewash . . .

Our 4-step guide will show you how to prepare, prime and decorate interior limewash and distemper walls, with product recommendations.

Can you paint storage heaters . . .

See our Radiator and Storage Heater Paints for the best products for domestic, commercial, and industrial application; our heat resistant radiator and storage heater paints won't yellow, peel, split or blister under intense and prolonged periods of medium to high-heat, making them ideal for touch-up maintenance issues, or for application to new constructions.

Can you paint over wood stain . . .

You can - see our blog posts below for painting over interior and exterior wtsianed wooden surfaces:

Can you paint plastic window frames . . .

See our blog posts below for painting PVC and UPVC window frames; the finish coats are available in hundreds of colours and shades to spruce up old and tired-looking plastic window frames.

How To Paint Over PVC
How To Paint Plastic And UPVC

What is eggshell paint . . .

Our blog post for the more popular questions we're asked about paint says:

"Eggshell paint is a type of paint finish that does actually look like the surface of an eggshell. Comparing it to more commonly found finishes in the UK, it has less of a sheen than satin or silk but more than that of matt emulsion paint or ‘satinwood’."

"The eggshell paint finish is commonplace on heritage or rustic styled interior walls and can look spectacular when adding vintage characteristics to wood. Expect to find it used in living rooms, kitchens, bedrooms and even in conservatories, where its 20% sheen (approx.) can be set off nicely by the evening sunlight."

Where to use eggshell paint:

"How about bedroom furniture – drawers, wooden bedframes, even picture frames – or kitchen cabinets. In the living room it could be used on fireplaces/fire-surrounds, bannister rails, skirting-boards or to decorate hat and coat stands."

"It can also be used externally, on window sills for example, or on doors, as it doesn’t yellow very easily."

What is satin paint . . .

See our blog post on the subject: What’s The Difference Between Satin and Gloss Paint?

"A satin finish will leave you with a medium gloss, that doesn’t shine as much as gloss paint as it’s less reflective. It can be great for hiding imperfections because of the finish, whereas the gloss can highlight imperfections."

What is teak oil used for . . .

See our blog post Wood Oils: A No Nonsense Guide for a comprehensive look at different wood oils, including teak oil.

Can you use teak oil on any wood . . .

See our blog post Wood Oils: A No Nonsense Guide for a comprehensive look at different wood oils, including teak oil.

How to temporarily fix a leaking flat roof . . .

See our comprehensive blog Roof Repair: How to fix a leaking flat roof for application advice and our recommended products to use.

Can you paint upvc windows and doors . . .

Difference between teak oil and danish oil . . .

See our blog post Wood Oils: A No Nonsense Guide for a comprehensive look at the difference between wood oils, including teak and danish.

Can you use teak oil on pine . . .

Danish oil will offer the most durable finish for pine furniture.

How to paint a upvc front door . . .

See our blog post, How to Paint uPVC Windows and Doors, for preparing, priming and finishing in more than 350 colours with our recommended products.

Best oil for outdoor wood furniture . . .

See our blog post Wood Oils: A No Nonsense Guide for a comprehensive look at different wood oils for outdoor wood furniture such as tables, benches and chairs.

Heat resistant paint for fireplace surround . . .

Our Fireplace Surround Paints are also ideal for use around radiators, fire stoves, and hot pipes - see our blog post for Painting the Walls around a Fireplace or Multi Fuel Stove for more recommendations and application advice.

Will painting over rust stop it . . .

See our blog post That Moment When You Realise You Can Paint Over Rust for an in-depth look at our recommended products for painting over rust and application advice.

Damp proof paint for internal walls . . .

Rawlins Paints stock a range of damp proof paints which have anti-condensation, mould resistant and anti-fungal properties, all in a choice of finishes with long lasting solutions to any damp problems. If you require assistance with a full hygienic paint system installation, contact our Technical Support team on 0113 2455450 (option 2) or send a message to [email protected], who’ll be happy to help with preventative measures that meet your environmental conditions.

Difference between satin and gloss paint . . .

See our blog post: What’s The Difference Between Satin and Gloss Paint?

Best metal paint to prevent rust . . .

Refer to our blog post How Rust-Inhibiting Metal Primers Work for our recommended products and application advice.

Paint to stop damp on walls . . .

Our recommendations can be seen in the blog post The Difference Between Damp Proof Paint and Anti-Condensation Paint.

Best paint for metal garage door . . .

See our recommendations in the blog post How To Paint Metal Garage Doors

Best masonry paint for coastal areas . . .

Our recommendations can be found on the blog post What is the Best Masonry Paint?

"Keim Royalan, applies on all mineral substrates and is formulated for use in extreme conditions. It is more resistant to fungal and algae growth that are more prevalent in humid and coastal environments, with all of the properties and benefits of mineral paint. Because of how harsh coastal conditions can be, Keim Royalan requires specification before purchase and is therefore only available as “price on application” – visit the product page to see more details, find data sheets, and to contact our technical team to discuss your requirements."

How to repair a flat roof . . .

For application advice and our recommended products, see the blog post Roof Repair: How to fix a leaking flat roof.

Intumescent paint for steel building regulations . . .

See our extensive range of steel intumescent paints - contact our technical team with your requirements and specifications on 0113 2455450 (option 2) or send a message to [email protected].

Best oil for dry wood furniture . . .

See our blog post Wood Oils: A No Nonsense Guide for a comprehensive look at different wood oils for outdoor wood furniture such as tables, benches and chairs.

Best natural oil for wood furniture . . .

See our blog post Wood Oils: A No Nonsense Guide for a comprehensive look at different wood oils for wood furniture.

How to paint over rusted metal . . .

See our blog post That Moment When You Realise You Can Paint Over Rust for an in-depth look at our recommended products for painting over rust and application advice.

How to paint over varnished wood . . .

Our blog posts below details how to paint over varnished surfaces, and the products to use.

How to paint stainless steel . . .

Please refer to our blog post: How to Paint Stainless Steel

I live on a Dutch corton steelboat circa 1975 I wish to paint the decks in a 2 pack for long standing protection, approximately 60sq ft, can you advise please . . .

Assuming the decks are clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Teamac High Performance Polyurethane Topcoat.

If any areas are back to bare metal we recommend Teamac 2 Pack Zinc Phosphate Primer prior to application.

I have just had new concrete flags put down outsie , need to anti slip them and look nice at the same time , what would you recomend please Something with no prep at all. Thank You . . .

No preparation will effect the adhesion and lifespan of any applied paint. Assuming the concrete slabs are clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Coo-Var Antislip Acrylic Floor Paint.

Hi I’m looking to seal a cement ridged flat garage roof ... as it has become a little porous in places. Which product would you recommend please. 3x7m roof. . . .

Assuming you are looking to recoat the roof and it is clean, dry and sound we can recommend Britannia Aquashield Eco for this application.

I am interested in the translucent exterior varnish and how or where I could purchase the product in Ireland . . .

You can purchase products directly from our website www.rawlinspaints.com from Northern Ireland. If you are in the Republic of Ireland please contact us for pricing and lead times on 0113 2455450 (option 1) or [email protected]

Hi My name is paula and I am writing to ask for some advice please . We have a caravan with the pvc decking and ramp for a lady with disabilities who suffers panic attacks and becomes unsteady on her feet and the ramp is fabulous b . . .

Assuming the substrate is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Smartkote Safekote.

Substrate preparation and primer recommendations can be found in the Technical Data Sheet,

Hi. We are making a sculpture (of sorts) out of stainless sheets. The sheets have been laser cut into shape and etched at the same time to define different areas of colour. There will be six colours, Bright red, bright blue, bright . . .

Assuming the stainless steel is clean, dry, sound and prepared as detailed in the Technical Data sheet we can recommend Rust-Oleum 3302 CombiPrimer Adhesion followed by Rust-Oleum CombiColor Original.

This is available in many RAL and BS colours but only in a satin finish with the colours required.

Hello I would like to spruce up the front of my house A composite front door, 2 upvc windows and a glass fibre double garage door I’d like to paint them all the same colour in a subtle light grey What recommendations do you have . . .

Assuming all the substrates are clean, dry, sound, prepared as detailed in the Technical Data Sheet and the UPVC is aged we can recommend Zinsser Allcoat Exterior Water based for this application.

This is available in many RAL and BS colours in a matt, satin or gloss finish.

Hi, I am trying to source a black weather proof paint to use on my recently acquired caravan wooden decking. I applied a good quality undercoat and top coat last September but the paint has started to peel and lift. Can you recomme . . .

Assuming the decking is clean, dry, sound and prepared as detailed in the Technical data sheet we can recommend Coo-Var Penetrating Wood Primer followed Coo-var Acrylic Floor Paint.

If you require an antislip finish we can recommend Coo-Var Suregrip Anti-Slip Floor Paint.

These are available in a range of colours in a semi-gloss finish.

Hi, what’s the best paint to put on a green mineral felt flat roof . It needs to protect and reflect and look good as it is seen from bedroom window . Also some water does lay on it after heavy rain . Regards Graham. . . .

Assuming the roof is clean, dry, sound and prepared as detailed in the Technical data sheet we can recommend Britannia Aquashield Eco.

This is available in black, grey or solar reflective white.

Hi can you recommend a non-slip paving slab paint?

Assuming the paving slabs are concrete, clean, dry, sound and prepared as detailed in the techncial data sheet we can recommend Smartkote Protectakote UVR.

Primer requirements can be found in the Protectakote Primer Guide in the datasheets tab.

Hi. I'm looking to re-spray my boat stove but, frustratingly, can't get the paint from manufacturers. It's a beautiful high gloss wine red colour. Can send pics. Can you help at all? Tracie . . .

Unfortunately we do not have a product we can recommend for this application.

I have a flat roof with black rubber covering , what paint would you recommend to reduce solar gain . Approx. 60m2. Thanks . . .

Assuming the roof is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend GacoPro Roof Coating.

This is available in solar reflective white.

Hi i want to paint my beige wet room floor grey is there a suitable paint i can use thanks

Assuming the floor is clean, dry and sound we can recommend Smartkote Safekote.

Please see the Technical Data Sheet for any primer requirements for the substrate.

This is a bare foot safe antislip paint available in a selection of colours including grey.

Hi, I'm looking for an aerosol in RAL 7016 to paint metal. Thanks

Assuming the metal is steel, clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum Hard Hat Topcoat.

Hi Looking for some paint for a new galvanised external staircase. Ideally in slate grey RAL7015 or similar. The fabricators have said to use t-wash first and then paint. Do I need a primer aswell? What would you recommend? Many th . . .

Assuming the galvanized staircase treads are not being painted, the structure is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3202 Galvinoleum Primer.

Followed by 2coats of Rust-Oleum 7500 Alkythane on the structure.

I have a garden path and patio on sandstone coloured concrete but want to change the colour to a slate grey (just want rid of the sandstone look). Do you have Paint or dye / sealant or other product that will achieve this? It’s l . . .

Assuming the concrete is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum Tarmacoat. This is available in with 2 grey colour options.

Is there a paint I can use on a marble fireplace thanks

Unfortunately we don’t have a product to recommend for this application.

I have a hole in wall fire it’s surrounded by marble and a metal brass coated trim . I am unable to remove the trim and want to paint it either black or chrome , can I do this with a heat resistant paint and brush as don’t want . . .

Unfortunately we don’t have a product to recommend for this application.

Looking to pain wooden kitchen cupboards from new ie bare wood. Do you have a colour range to choose from please? . . .

Assuming the bare timber is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser B-I-N followed by 2 coats of Zinsser Perma-White Interior.

This is available in many RAL and BS colours as shown on the product page in a matt or satin finish.

Dear All, Hello, We are air conditioning contracting company, We have a high rise tower project and we are facing a problem in condensation at black steel supports of chilled water balck steel piping internal Temperature of 5 degre . . .

Unfortunately we do not have a product we can recommend for this application.

Hi, I was wondering if you had a rubber paint that could be used as the floor of a campervan shower?

Assuming the substrate is already waterproof, clean, dry and sound we can recommend Smartkote Safekote.

This is a bare foot friendly anti-slip paint available in a range of colours and a clear option.

Do you have a tarmac coating for a school playground which protects against damage / corrosion from seagull (birds in general) droppings? . . .

Assuming the tarmac is clean, dry and sound we can recommend Hydron Mona-Guard Revive. This is suitable for use in high footfall areas, provides some resistance to stains, chemicals and dirt.

Hi, I'm looking to paint external concrete forming the top of two old-style sunken septic tanks. Ideally I'd like a green non-slip finish. Can you recommend a paint for this? Thanks . . .

Assuming the concrete is clean, dry, sound and prepared as detailed in the Technical data sheet we can recommend Coo-Var Anti-Slip Acrylic Floor Paint.

This is available in a forest green colour option.

Hi guys, I've been looking at your combi colour metal paint to possibly roller paint my van. What paint would you recommend The original combi colour paint Or the combi colour multi surface. Many thanks . . .

Assuming the van is previously painted steel, clean , dry, sound and prepared as detailed in the Technical Data sheet we can recommend Rust-Oleum CombiColor Original.

This is available in many RAL and BS colours in a satin or gloss finish.

If you have any areas of bare steel we would recommend priming with Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion prior to application.

Hi can you advise me on what paint I should use to paint a walk in cold storage room used for food storage in a chip shop. Thank you . . .

Assuming the substrate is compatible, clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum 5500 Solvent Free Epoxy.

This is available in a range of colours in a gloss finish and is approved for direct dry food contact.

Is Teamac Marine Gloss 2 suitable for use on metal? I am unable to read the label.

Teamac Marine Gloss requires a primer for use on metal. Assuming the metal is steel, clean dry and sound we can recommend Teamac Marine Undercoat followed by Teamac Marine Gloss.

I have a rusty metal parasol base with some green paint still on it , i would like to paint it dark grey , can you help ! . . .

Assuming the metal parasol base is steel, clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by Rust-Oleum CombiColor Original.

This is available in many RAL and BS colours in a satin or gloss finish.

Hello. I need to find a black paint for my outside roof tiles, I’ve been advised to get an oil based one as a previous one we used washed off in the rain. Have you any suitable weatherproof paint? Many thanks! Nikki . . .

Assuming the roof tiles are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Mathys Dac Hydro Plus.

This is available in many colours including black.

I'm looking for a product to coat a pitched fibreglass roof on a chalet. The roof is probably 45 years old, doesn't leak but needs something to freshen it up. It's a brick red colour just now so would like a similar colour for the . . .

Assuming the roof is water tight, pitched, clean, dry and sound we can recommend Tor Unicover S.

This is available in many RAL and BS colours in a semi-gloss finish.

What anti slip paint is suitable for shower/locker area, concrete floor already painted with an anti slip resin paint. . . .

Assuming the floor is clean, dry, sound, the previous coating is well adhered and prepared as detailed in the Technical Data sheet we can recommend Smartkote Safekote for this application.

This is a barefoot friendly anti-slip paint available in a range of colours and clear.

What primer and satin black paint can I use on wrought iron fence for outside in harsh weather conditions? and one that can last for a long time . . .

Assuming the wrought iron fence is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion, followed by 2 coats of Rust-Oleum CombiColor Original.

Hi I have two leaking valleys and I'm looking for a fiberglass paint or similar to seal the leak. It's a new house 2008 with what looks like lead valleys and two seems to be leaking and I'm looking for a product to paint the lead t . . .

Assuming the valleys are lead, it is aged, clean, dry and sound we can recommend Rust-Oleum Mathys Fillcoat Fibres.

I have a pathway that is made of marble crazy paving (not laid by me I hasten to add!) It’s absolutely lethal and I’m looking for something that will help until I can afford to have it ripped up and replaced with something more . . .

Assuming the marble is clean, dry, sound, and prepared as detailed in the technical data sheet we can recommend Smartkote Protectakote Clear Primer Treatment followed by Smartkote Protectakote UVR.

This is an anti-slip paint available in a range of colours and a clear option.

We need to repaint our external security gates dark green, to match railings either side. Originally powder coated galvanized steel in 2000, they were repainted by one of residents 5 years ago, but the paint has peeled badly. What . . .

Assuming the previous coating of paint is removed back to a clean, dry, sound substrate and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3302 CombiPrimer Adhesion followed by 2 coats of Rust-Oleum CombiColor Original.

This is available in many RAL and BS colours in a satin or gloss finish.

Do you have a silicone based high heat paint safe to recoat the cooking surface of a cast aluminum electric grill? . . .

Unfortunately we do not have a product to recommend for this application.

Hi I've been searching for a really good UPVC paint for windows and doors in a mid to dark grey and I'm finding it so difficult to find what I want/need. Please can you hep . . .

Assuming the UPVC is aged, clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Zinsser Allcoat Exterior Water Based.

This can be applied directly to prepared aged UPVC and you will require two coats.

This is available in many RAL and BS colours in a matt, stain or gloss finish.

Your help please We have two warehouses joined with a central cement/asbestos gutter that is leaking badly through joints & a few cracks Maintenance is having a complete nightmare & left it to the office ladies to find a so . . .

Assuming the asbestos is clean, dry and sound Rust-Oleum Mathys Fillcoat Fibres can be used on asbestos to bridge cracks upto 2mm.

The areas to be painted must first be primed with Rust-Oleum Mathys Primer 44 HS.

Surfaces should be cleaned and a fungicidal solution such as Rust-Oleum Mathys AMW Fungicidal Wash prior to application.

Hi we want to waterproof an asbestos garage roof with over lap sheets it’s 18 metre square what’s the best and how much of each this roof has never been touched since was built . . .

Assuming the asbestos sheets are clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Britannia Aquashield Primer, followed by Britannia Aquashield High Build.

You will require 6ltr of Aquashield Primer and approximately 36kg of Aquashield High Build for the 18m².

Could you please advise which products I can use to paint MDF. I have found a primer On your site and wondered which top coat you recommend? Thank you . . .

Assuming the MDF is for interior use, clean dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser Bulls Eye 1-2-3 primer followed by 2 coats of Zinsser Perma-white interior.

This is available in many RAL and BS colours in a matt or satin finish.

I am looking for paint to roller my campervan please can you advise which is best

Assuming the campervan is steel, previously painted, clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum Combicolor Original.

This is available in many RAL and BS colours in satin of gloss finish.

If there are any areas of bare steel these should be primed with Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion prior to application.

what type of spray gun do i need to apply Thermoline 450 ?

Please see the Application Equipment Guidelines section of the Technical Data Sheet for all spray equipment requirements.

This can be found in the data sheet tab on the product page linked below. Carboline Thermaline 450

Have you a product that will extend the life of tanalised wooden posts that may be under water for a period of days or even weeks? I’m building a fence with 4 inch square tanalised pine posts that will be attached to a wall along . . .

Assuming the tanalised wooden posts are clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Teamac Metaclor Primer followed by 2 coats of Teamac Chlorvar Chlorinated Rubber.

This is available in many RAL and BS colours in a gloss finish.

Hi, could you please advise in your professional opinion, if painting PVC windows and doors is a good idea? They are currently brown and I'd like black. Also, how do I know if its PVC or uPVC I have and does this make a difference. . . .

Most plastic windows are UPVC and are regularly refinished for cosmetic purposes.

Assuming the aged UPVC windows are clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Zinsser Allcoat Exterior Water Based.

This is available in many RAL and BS colours in a matt, satin or gloss finish.

Hi I’m building a plywood above gnd swimming pool. Do you have a rubberised paint that will waterproof the pool replacing the need for a liner ?? Thanks . . .

Unfortunately we do not have a product to recommend for this application.

We are opening a new food delivery service and wanted to know the best wall paint for a food preparation area. the foods are all cold (no cooking) and will be prepared on commercial grade worktops so it is only the surrounding wall . . .

Assuming the walls are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Biosan Aqua Plus.

This is available in many RAL and BS colours in a satin finish.

I have a Chrysotile corrugated panel roof that needs a little repair . There is some small holes in a couple of areas and one crack about 3' long in another section. What would you recommend for these types of repairs. . . .

Assuming the asbestos roof sheets are clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Britannia Aquashield Primer followed by Britannia Aquashield High Build.

This is available in grey, black or solar reflective white.

I would like to paint my 110CM Range Cooker doors (Gas heating Oven and Storage), as the existing paint is pealing off. What is the best paint (Grey colour) to use that can withstand the oven heat. . . .

Unfortunately we do not have a product to recommend for this application.

Hi, We have been asked to pain a galvanised vent, do you carry a paint which has one coat finish no primer needed. with a multiple of colours. . . .

Assuming the galvanised vent is cleaned and degreased with
methylated spirit, lightly abraded, any white salts on weathered galvanising are removed during cleaning and degreasing, we can recommend Bradite One Can.

This is available in many RAL and BS colours in an eggshell finish.

Any light surface rusting should be treated with Bradite Fastrac Rust Converter prior to application.

I want a metallic gunmetal colour brush-applied paint to finish primed railings

Assuming the primer applied is compatible, the railings are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum CombiColor Original. This available in metallic colours with a gloss finish.

I've got metal gutters that need replacing ...untill then I need to repair a leak Is the a fast drying paint that will repair it ? . . .

Assuming the metal gutters are clean, dry and sound we can recommend Rust-Oleum Mathys Fillcoat Fibres.

This will bridge cracks or holes upto 2mm.

Hello, I have a hard wood verandah with wooden slats for walking on and wooden handrails. It is south facing so gets the sun and is subject to very light traffic. It was previously covered with Dulux woodstain, some of which I have . . .

Assuming the wooden slats and handrails are clean, dry, sound, abraded and degreased with Rust-Oleum Thinner 160, we can recommend Rust-Oleum 7200 Floorcoat PU for areas subject to foot traffic and Rust-Oleum 7500 Alkythane for the handrails.

These are available in many RAL and BS colours in a gloss finish.

If you require a non slip finish you can add Rust-Oleum Non-Skid Additive NS 100.

Does conseal tu have to be thinned before applying to steel

If applying by airless spray this must be thinned 5-10%. Application by brush can be unthinned.

Can use chlorinated rubber paint on enamal painted surface

No, assuming the enamel is removed, the substrate is compatible, clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Teamac Chlorvar Chlorinated Rubber.

Hi, I'm renovating an old atv trailer for my sheep. Can you advise on the best primer for the frame to kill/inhibit rust. It will be sanded down first with a metal brush etc. I'm planning on using Rust-Oleum for it's top coat. Kind . . .

Assuming the trailer is made of steel, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by 2 coats of Rust-Oleum CombiColor Original.

Hello Do you sell a flexible, uv stable paint that would be suitable to waterproof a concrete pond - wildlife friendly? Thanks Kate . . .

Assuming the concrete is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Teamac Chlorvar Chlorinated Rubber.

This is used for waterproofing swimming pools and ponds but does not specifically list being wildlife friendly.

This is available in many RAL and BS colours in a gloss finish.

Hello, Question: Do you do a product I can use to level off a flat fiberglass roof and stop the pooling when it rains. ? Thank you . . .

Unfortunately we do not have a product to recommend for this application.

Do you have anything to stop salt dripping out of a stone lintel?

Assuming the stone lintel is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend treating the lintel with Blackfriar Anti-mould Solution followed by Zinsser Watertite.

What is the best exterior floor paint for concrete slabs and steps with heavy traffic use I’ve seen some Brands like kilz coo at or rustoleum . . .

Assuming the metal box gutter is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Mathys Fillcoat Fibres.

This will seal leaks and cracks upto 2mm.

Hello Which product would be best to reseal an old fibre glass roof on a camper van which is beginning to crack and leak. Many thanks . . .

We would recommend GacoPro Roof Coating as the easiest and longest lasting system you could apply.

Looking for a rust treatment and paint for a metal external staircase. Options from you would be appreciated . . .

Assuming the staircase is steel, clean, dry and prepared as detailed in the techncial data sheet we can recommend Rust-Oleum 769/780 Damp-Proof Rust Primer followed by Rust-Oleum 7200 Floorcoat PU on traffic'd areas and Rust-Oleum 7500 Alkythane on the other areas. These are available in many RAL and BS colour options in a satin or gloss finish.

Hi, I have installed ceiling mounted IR heaters at a property where the ceiling is white painted timber, with water based satinwood paint. Even though the heaters point down they have caused the paint to bubble with the excess heat . . .

We wouldn't have anything we could recommend paint wise for this application so it is likely you would need to alter the mounting distance or potentially change the substrate they are mounted on to.

Can I paint this on vinyl furnishing

Unfortunately we currently wouldn;t have anything we could recommend for application on to vinyl furnishings.

I have cleaned primed and painted woodwork with homebase brand paint. When slightly knocked or wiped down the paint comes off. Should the paintwork be coated with anything? . . .

Rust-Oleum 4900 Polycoat 2K is a clear, water-based, 2-component polyurethane topcoat for use on wood, concrete and pre-painted surfaces, and also serves as an anti-graffiti coating. Very abrasion resistant, available in a matt or gloss finish, does not yellow, can be used internally and externally, resists boiling water, alcohol, coffee, red wine, dilute acid and alkalis

I have a bungalow with concrete floor which I wish to paint. Which product should I use and I am looking for colours other than grey, black , white , red etc Can you help. vmt k . . .

Bradite Floor-It, a high-performance ambient crosslinking water-based acrylic floor paint with low odour and non-yellowing, fast-drying formula that is ready for light use in just 16 hours. Ideal for garages, workshops, kitchens, bathrooms, staircases and light industrial traffic.

Hi , Have a tarmac drive with red stones in the surface, is there a clear solution that can be applied to buff up the surface ? . . .

I'm afraid we wouldn't have any products we could recommend for your application.

Can your paint be used on a tiled fireplace place surround that is in use for a open fire ?

Please see the following link for painting the walls around a fireplace or multi-fuel stove - https://www.rawlinspaints.com/blog/painting-the-walls-around-a-fireplace-or-multi-fuel-stove/

Hi. We have just acquired a 1979 alloy bodied campervan but the bottom part is fibreglass. It's looking a bit old and won't polish up. What can we do with it. Thanks. . . .

Assuming the fibreglass is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum CombiColor Multi-Surface.

This is available in many RAL and BS colours.

Looking for a tile Paint would the Rust Oleum combi colour multi surface be the correct one? If so do you do a colour chart in hard copy as my mother wants to see it in hard form rather than online? Thanks Melissa . . .

Assuming the tiles are not on a floor or in direct water contact such as in a shower, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum CombiColor Multi-Surface.

This is available in many RAL and BS colours.

As this is mixed to industry standard colours we would advise looking at a RAL colour chart at a local DIY store as the manufacturer does not produce colour swatches.

Hi, I am looking for a matt black, heat resistant paint for a 45mm thick hardwood door. The sun shines directly on the door to such an extent that the door gets too hot to touch. The existing paint has blistered and we want to avoi . . .

Unfortunately we do not have a product to recommend that is heat resistant or reflective for this application.

Painting the door in a lighter colour would assist in reducing the heat.

Assuming the blistered, loose material is removed, the door is clean dry and sound we can recommend Zinsser Cover Stain followed by two coats of Zinsser AllCoat Exterior.

This is available in many RAL and BS colours in a matt, satin or gloss finish.

Hi, We need to paint (in black) our bricks that are below our damp course for visual but also to waterproof/repel water but we also want to paint our blocks (trench blocks) that are below the above bricks and these will be below gr . . .

Assuming the bricks are clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Eagle Quick Drying Bitumen Primer followed by Eagle Black Bituminous Paint.

Can I use Zinsser as a primer on upvc doors prior to using an ordinary make Understand and gloss finish

Assuming the UPVC is aged, clean, dry and sound we would recommend applying Zinnser Allcoat Exterior Waterbased.

This can be applied directly with no primer required and mixed to many RAL or BS colours in a matt, satin or gloss finish.

Zinsser Bulls Eye 1-2-3 can be applied to UPVC but compatability with other manufacturers topcoats is untested.

Hi I’m looking for a sealant for laminate flooring in my kitchen. It’s standard click together laminate but edges are starting to lift at the edges near the sink. Can you recommend an easy to apply waterproofing? Thanks Mrs Par . . .

Unfortunately we do not have a product to recommend for this application.

Hi I am after paint that I can put on my conservatory roof that will make it a lot cooler am mainly deflect the glare from the sun as I find it very difficult to watch the tv. Do you sell any products like this? Thanks . . .

Assuming you are looking to paint the exterior of the roof, it is Polycarbonate, clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Britannia Aquashield Eco.

This is available in black, grey and Solar Reflective White.

Please be aware as it is a clear substrate brush strokes may be visable on the interior and even the Solar Reflective White will reduce the amount of natural light.

I have galvanised railings to paint, after using a mordant solution in preparation what paint in white could you recommend in 1ltr tins would the combi colour be ok. . . .

Assuming the galvanised steel railings are clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum CombiColor Original.

This is available in many RAL and BS colours in a matt, satin or gloss finish.

For a Mordant Solution we can recommend Teamac Mordant Solution (T Wash).

I'm trying to find some paint that would be suitable to repaint my large range cooked on the outside. The doors have began to rust. I'm not sure of what paint I would need to give the best finish. I have someone who will Cary out t . . .

Unfortunately we do not have a product to recommend for this application.

hello , I have glass windows in a restaurant. They will no longer have a view due to a new external structure . I want to use polyine scumble for paint effects . Is there a primer that a can use on the glass that may then be coated . . .

Assuming the glass is clean, dry, free from anything that could affect adhesion and prepared as detailed in the Technical Data sheet we can recommend Zinsser Bulls Eye 1-2-3.

Zinsser Bulls Eye 1-2-3 is a water based adhesion primer suitable for glass, but you would need to trial the coatings you are planning to use over the top of it as we have no information to confirm if they would be suitable or not.

hi I'm looking at your combi colour can you mix it in rover targa red paint code (cne) as its for a classic mini thank you dave . . .

Rust-Oleum CombiColor Original can be mixed in many RAL and BS colours, unfortunately it cannot mixed to automotive paint codes.

What is the best thing to get diesel and power steering fluid off of a tarmac drive without damaging the tarmac? . . .

Assuming the Tarmac is dry and sound we can recommend Coo-Var Oil Remover.

Does the worktop paint come in more colours ?

Rust-Oleum Worktop Transformation Kit is available in two colour options, Galaxy Black and Diamond White.

Hi can you recommend best paint and sealant with anti slip for floor tiles (medium to heavy duty traffic). Many thanks Steve . . .

Assuming the medium to heavy traffic is foot, the tiles are clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend priming 1st with Smartkote Protectakote Clear Primer Treatment before applying 2 coats of Smartkote Protectakote UVR.

This is available in a range of colours and a clear option.

Dear Sirs, I am looking for an anti slip waterproof surface to be applied to plywood. We have a van in which we want to transport dogs. The non slip surface is to help prevent the dogs sliding around when in transit. The coating mu . . .

Assuming the plywood is clean, dry, sound, prepared as detailed in the Technical Data Sheet and Protectakote Primer Guide we can recommend Smartkote Safekote for this application.

This is available in a range of colours and a clear option.

Hello What would you recommend for painting old vinyl floor tiles in a bathroom? Would the floor paint require a primer? Thanks, Karin . . .

Assuming the vinyl is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Smartkote Safekote.

This is a barefoot friendly anti slip paint available in a range of colours and a clear option.

I'm looking for a foodsafe, hard, clear coating to produce 3D printed, painted mugs for my home business. The coating will come in direct contact with beverages. I have looked through your product line, and am unsure of which is th . . .

Unfortunately we do not have a product to recommend for this application.

Good evening, I am looking for a brilliant white paint that is suitable for painting inside my fire pit recess where I will be having a log burner. The area is around 2.5m Square. Please could you advise me which product is suitabl . . .

Please see our blog post, Painting walls the around a fireplace and multi fuel stove.

hi. I have balcony metal railings which are rusting. Pse can you recommend best course of action? Ie. Clean, wire brush, primer, paint black? If primer and black paint can you advise which to order? Thanks . . .

Assuming the steel railings are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by two coats of Rust-Oleum CombiColor Original.

This is available in many RAL and BS colours in a satin or gloss finish.

Need to paint paint over kitchen floor tiles what type paint would you recommend please many thanks Michael . . .

Assuming the floor tiles are glazed, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Smartkote Protectakote Clear Primer Treatment followed by Smartkote Protectakote UVR Smooth.

If you require an antislip finish we can recommend Smartkote Safekote.

These are available in a range of colour and a clear finish.

Do you have printed colour charts for the rustoleum combi colour range? I'm looking one of the blues, in satin. Thanks Rick . . .

No but the paint is available mixed to many RAL and BS colours.

A RAL colour chart can normally be found in most hardware shops.

Do you do stair treads for house stairs

Assuming this is internal then we'd recommend Rust-Oleum SuperGrip Anti-Slip Step Covers (Interior) as they have a smaller, less aggressive anti-slip surface.

i have a fibre glass roof with top coat gray on it. im wanting to go over it but not with a grp top coat paint, as they tend to crack !! what is your suggestion, approx 10 sqm . . .

Assuming the GRP roof is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Britannia Aquashield Eco.

This is available in black , grey and solar reflective white.

For one coat you will require 20kg.

I would like to make my exusting victorian 4 panel pine doors to achive fd30. I could cover 1 side with a resistant solid panel if required.what can you supply or recommend for me. Regards Wayne Smart . . .

Thank you for the enquiry, we have contacted you directly by email.

Good morning. We need a metal paint colour Anthracite Grey that can be used on Galvanised Steel. Can you help us. . . .

Assuming the galvanised steel is clean, dry, sound and prepared as detailed in the Technical Data Sheet, not exposed to foot traffic we can recommend Rust-Oleum 3302 CombiPrimer Adhesion followed by two coats of Rust-Oleum CombiColor Original - Anthracite Grey.

Hello I’m looking for outdoor concrete paint for mconcrete patio that has a bit of texture to go over cracks and bumps. Can you recommend something? . . .

Assuming the concrete slabs are clean, dry, sound and prepared as detailed in the Techncial Data Sheet we can recommend Smartkote Protectakote UVR.

This is an antislip paint so it has texture but please be aware it will not bridge or fill cracks.

Hi. Morning I am looking to purchase a floor paint for a metal stair case that gets wet when it rains however I don't want a smooth finish paint, I need a paint that finishes leaving a textured look and feel so as to avoid slipping . . .

Assuming the metal staircase is steel, clean, dry, previous coatings are sound and it is prepared as detailed in the Technical Data Sheet we can recommend Smartkote Protectakote UVR.

The staircase should be abraded and cleaned with Xylene prior to application.

Hi.....Do you have the Britannia Aquashield waterproof roofing product in clear in stock please

Yes we stock Britannia Aquashield Smooth in a black, grey, solar reflective white colours and a clear option.

Hello, we are trying to find a good anti slip paint to apply to an external metal spiral staircase which runs down the back of our building to the garden as it gets very slippery when wet. We will be looking to apply it as soon as . . .

Assuming the stairs are galvanised steel, clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Smartkote Protectakote Clear Primer Treatment followed by Smartkote Protectakote UVR.

This is available in a range of colours and a clear option.

Hi, how can I obtain a colour chart? Do I need to order on online as no one seems to stock them, Kind regards Marc . . .

Currently you would need to source a colour chart elsewhere online as we're unable to supply one.

Is your exhaust paint suitable to apply on an exhaust MANIFOLD of a classic car, preferably either in a blue or silver, and what sort of prep would be required to the cast iron. Thank you . . .

Assuming the manifold is not exposed to temperatures over 600°c, it is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Jotun Solvalitt.

This is available in 5 litres in many RAL and BS colours in a matt finish.

If a smaller quantity is required we can also recommend Rust-Oleum Heat Resistant Paint 750°C.

But this is only available in black or aluminium with a matt or satin finish.

Please advise on a heat resistant paint for the edge of a chipboard worktop near a hob. Heat resistance to 90deg. Small amount, not a large can costing over £100, please. . . .

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Hi we have an engineered laminated timber floor which marks very badly with scuffing. Please can you advise what I can treat it with Thank you . . .

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Can you please advise me, I’m looking for an interior gloss in the Zinsser range in white. Also do they do any emulsion Thank you . . .

Assuming you are looking for an Zinsser interior gloss for application to bare timber, the substrate is clean, dry, sound and prepared as detailed in the Technical Data sheet we can recommend Zinsser B-I-N followed by Zinsser Allcoat Exterior Gloss (Waterbased).

This can be use in an internal application and is available in many RAL and BS colours.

Assuming the walls you require an emulsion paint for are clean, dry, sound and prepared as detailed in the Technical Data sheet we can recommend Zinsser Perma-White Interior.

This is scuff/scrub resistant and available in many RAL and BS colour options in a matt or satin finish.

I am a builder seeking a navy blue render (preferably silicone) RAL 5003 The job is around 80sqm

Thank you for the enquiry, we have contacted you directly for more information.

Regarding asbestos, please do you sell a paint suitable for a pitched roof covered in corrugated sheeting that contains an asbestos element. in a forest green colour (not grey), please? We're looking for primer and paint. Thank you . . .

Assuming you are looking for decorative finish and not for the purpose of waterproofing we can recommend Teamac Acrylic Coating for a green colour.

If a waterproofing paint is required assuming black, grey or solar reflective white is suitable, the roof is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Britannia Aquashield Primer followed by Britannia Aquashield High Build.

I would like to paint water resistant chipboard flooring. can you recommend a suitable primer and paint please. thanks. . . .

Assuming the chipboard flooring is only exposed to foot traffic, is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum 7200 Floorcoat PU.

This is available in many RAL and BS colours in a gloss finish.

good morning i have a leak from either the flashing or the corner joints on my EPDM flat roof, can you advise if any of your repair products adhere to epdm and would be suitable for a diy repair where I can paint onto these areas. . . .

Assuming the areas are clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Gaco Liquid Roof Tape.

This will adhere to EPDM.

Hi ,I would like to paint my uvpc front doors. They are oak colour. Do you have upvc, paint in that colour. Many thanks Julia . . .

Assuming the UPVC door is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Zinsser AllCoat Exterior (Water Based).

This is available in many RAL and BS colours in a matt, satin, or gloss finish.

do you sell coovar hammered finsih dark grey please for metal,

Yes we do please see the link to Coo-Var Hammercote Hammered Finish.

Hello, do you do a clear (ideally low VOC) clear laqure matt for metal, im wishing to add some pigments to this for a finish and protecxtion of metal surface, any advice would be appreciated, many thanks, richard . . .

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

hi im looking for preferlby a primer and paint to paint an alluminium shower frame needs to withstand water and steam online it says latex looking for a black colour any help would be appreciated thankyou . . .

Assuming the aluminium frame is pretreated with Teamac Mordant Solution (T Wash) is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Teamac High Performance 2 Pack Zinc Phosphate Primer followed by Teamac High Performance Polyurethane Topcoat.

This is available in many RAL and BS colours in a gloss finish.

Hi, I would like to paint my old concrete patio slabs, I intend to power wash first but wondered which paint you would recommend and should I repoint prior to painting. It would need to be as natural a colour as possible to stone. . . .

Assuming the patio slabs are clean, dry, sound and prepared as detailed in the Technical Data sheet we can recommend Coo-Var Acrylic Floor Paint.

This is available in a range of colours in a semi-gloss finish.

We would advise to repair any pointing prior to application.

Hi I have an exterior fire escape stairs which have galvanised checker plate treads and landings. Please could you advise which anti-slip coating would be most suitable. . . .

Assuming the galvanised checker plate is bare, clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Smartkote Protectakote Clear Primer Treatment followed by Smartkote Protectakote UVR.

This is available in a range of colours and a clear option.

Hi, Hope that you are well. I need to coat the underside of a steel beam used on a low rise residential drive through. The steel is finished in red oxide and is open to the elements. Can you suggest an solution please. . . .

Assuming the steel does not require any level of fire protection we can recommend Rust-Oleum CombiColor Original.

This is available in many RAL and BS colours in a satin or gloss finish.

If a level of fire protection is required please contact the Technical Team on 0113 245 5450 option 2.

Hi. I am looking for a paint suitable for covering a plastic shower tray in a motorhome. Do you have any products you can recommend? Many thanks. . . .

Assuming the plastic shower tray is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Smartkote Safekote.

This is a barefoot friendly anti-slip floor paint.

We woud recommend testing for compatibility and adhesion prior to application.

I am considering using anti-vandal paint on the top of a communal wrought iron gate giving residents access to a private road and their individual properties. If an intruder or indeed the applier of the paint should be contaminated . . .

Assuming you are looking at Britannia Anti-Vandal Paint, any spills on to skin should be removed quickly with a strong hand cleaner.

This product will not be removeable from clothing.

I have concrete steps that I want to make a little more slip proof. Would the paints also help against ice? And if so which one. Thanks. . . .

Assuming the concrete steps are clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Smartkote Protectakote UVR.

On bare concrete the first coat should be thinned 10% with 100 Rapid Drying Thinner.

This will provide an anti-slip surface and will help provide slip resistance against ice assuming water cannot pool on the steps.

Hi I am looking to paint my concrete patio. it is 4 meters by 3 meters. I want to coat it with anti slip paint. I purchased Anti-Slip Stair Tread Covers - Colour : Grey- Size : 345mm x 750mm ( your ref 1102) already and would like . . .

Assuming the concrete patio is clean, dry, sound and prepared as detailed in the Technical Data sheet we can recommend Rust-Oleum 7200 Floorcoat PU with Rust-Oleum Non-Skid Additive NS 100 added to provide an anti-slip surface.

This can be mixed to many RAL and BS colours, the antislip stair tread covers are not made to specific RAL colours so you will need to find a suitable match.

what is the best paint for fibre glass

Thank you for the enquiry, we have contacted you directly for more information.

Project, metal framed Crittall windows on exterior of church built in 1940, never galvanised but painted in a lead based paint. What product would you recommend to paint over the existing paint with minimal disturbance to surface. . . .

Assuming the previously applied lead paint is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser Bulls Eye 1-2-3 followed by 2 coats of Zinsser AllCoat Exterior (Water Based).

We would recommend testing for compatibility and adhesion on a small area prior to full application.

This is available in many RAL and BS colours in a matt, satin or gloss finish.

Hi there. We have a concrete path in our garden. We had previously painted it and it has worn off in places over a year or so. The paint was supposed to be outdoor but was perhaps not specialist enough. We want to strip it back and . . .

Assuming the concrete is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Smartkote Protectakote UVR Smooth, this is available in a clear option.

If you require a bare foot friendly anti slip paint you could consider Smartkote Safekote, this is available in a larger range of colours or a clear option.

We purchased thermoguard high metal red primer from you (May 2020) and I need the technical data information for this. Please can you email the data sheet, or direct me to where I can find it on your website. many thanks . . .

Thank you for the enquiry, please see the link below to the product page, the Technical Data Sheet can be found in the data sheets tab.

Thermoguard High Build Metal Primer

Do you sell a food safe black paint, that can be used on the cooking area of a grill?

Thank you for the enquiry, unfortunatley we do not have a product to recommend for this application.

Do you produce any paint or wood treatment which would stop rats climbing up a vertical post to access a bird table? . . .

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Can heat paint be used on b-b-q Heat / flavour shields inside the unit?

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Hi , the plaster above a wall mounted gas fire , has cracked due to the heat , noticeable under the standard paint , that has been used . After I have repaired the plaster which product do you suggest using to protect the plaster f . . .

Thank you for the enquiry, please see our detailed blog post regarding Painting the Walls around a Fireplace or Multi Fuel Stove.

I will need to paint a very small area of uPVC windowsill as part of a bathroom refurbishment. Would it be possible to buy a sample pot of Rust-Oleum Combi-Colour? (Colour would probably be RAL6018 yellow-green.) . . .

Assuming the Upvc is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum CombiColor Multi-Surface.

This is available in many RAL and BS colours in a gloss finish.

Unfortunately the manufacturer does not product sample pots but it is available in 1ltr tins.

Hi, I want to renovate some painted aluminium garden furniture. What product should I use to clean and prepare the surface and what metal paint do I need? I've been looking at CombiColor but am not sure if this is suitable. The met . . .

Assuming the painted aluminium furniture is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Zinsser Allcoat Exterior Water based.

We would recommend testing for compatibility and adhesion with the previously painted furniture prior to full application and any bare metal areas should be primed first with Zinsser Bulls Eye 1-2-3.

This is available in many RAL and BS colours in a matt, satin or gloss finish.

Is there a rustoleum colour chart available for all surface paint and floor paint.

Unfortunately the manufacturer does not produce a colour chart for these paints, they can be mixed to industry standard RAL and BS colours.

A representation of these is on the product page, but we would recommend viewing a RAL colour chart in person to ascertain the correct colour.

Hi there I’m looking for products to paint the exterior of our business premises. The building is a type of dark sandstone and currently painted white but there are areas prone to staining. Keen to retain the white colour and pre . . .

Assuming the previously applied paint is clean, dry, sound and prepared as detailed in the Technical Data sheet we can recommend Wethertex AP77 Flexible Smooth Masonry Paint.

This is highly weatherproof and resistant to staining.

Do you do a paint for tired outside paving slabs? Many thanks Craig

Assuming the concrete paving slabs, are clean, dry, sound and prepared as detailed in the Technical Data sheet we can recommend Coo-Var Anti-Slip Acrylic Floor Paint.

This is available in many RAL and BS colours in a semi gloss finish.

Want to paint motorbike engine in high heat satin black paint, please advise what paint and if a primer is required, aerosol rust oleum I was looking at Thanks John . . .

Assuming the engine is steel, bare, clean, dry, sound and prepared as detailed in the Technical Data sheet we can recommend Rust-Oleum Heat Resistant Paint 750°C.

This is available in satin black in a 500ml aerosol and is for use in internal or sheltered environments.

This would not be recommend if the bike is left regularly outside.

If this is a requirement you could consider Jotun Solvalitt but this is only available in a matt finish.

I need to know how to prepare brick for outside painting please. Also, do you have silver colour masonry paint? . . .

Assuming the brick is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser AllWeather Exterior Masonry Paint (Solvent Based).

This can be mixed to many RAL and BS colours including RAL 7001 Silver Grey.

This can be applied directly to clean, sound brickwork.

do you supply colour test pots of the combicolour please?

Thank you for the enquiry, unfortunately the manufacturer does not produce tester pots, the smallest tin size is 1ltr.

We need a paint that can be sprayed, to coat the interior of cast iron columns. The aperture into the columns is only 80mm diameter, at the bottom of 8m high columns. We will only be able to remove the loose corrosion/deposits from . . .

Assuming the internal surfaces of the cast iron columns are clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum 9169 Epoxy Rust Primer.

This can be applied by conventional and airless spray.

I need a very bright red concrete paint for outdoor use. Only need a small amount. What would you recommend. . . .

Bradite Polyurethane Floor Paint

Assuming the concrete is not subject to vehicle traffic, it is clean, dry, sound and prepared as detailed in the Technical Data sheet we can recommend Bradite Polyurethane Floor Paint.

This can be mixed to many RAL and BS colours in a semi gloss finish.

Best paint to refurbish, a white composite kitchen sink.

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Is the exterior paint safe for pets of they lick it or bite through it.

Thank you for the enqury, unfortunately we do not have a paint we can recommend that is pet safe or suitable for ingestion.

which roof coating would you reckomend for fibre cement slates

Assuming the fibre cement slates are clean, dry, sound and prepared as detailed in the Technical Data sheet we can recommend Rust-Oleum Mathys Dac Hydro Plus.

This is available in a range of colours in a matt finish.

I have Rosewood UPVC guttering that that needs refreshing, is this in your range of colours. If so quantity and costs? Thanks . . .

Assuming the UPVC is clean, dry, sound and prepared as detailed in the Technical Data sheet we can recommend Zinsser Allcoat Exterior Water Based for this application.

It can be mixed to many RAL and BS colours in a matt, satin or gloss option.

This paint covers approximately 12m² per litre per coat.

What product would you recommend to block white effervescence appearing through masonry painted external block walling in good condition? . . .

Assuming the efflorescence is removed, the wall is clean, sound and prepared as detailed in the Technical Data sheet we can recommend Zinsser Watertite.

This product works best on a bare substrate, we would recommend removal of the old paint prior to application.

Hello I’m after a recommendation for two part paints for use on a fresh water boat steel hull below the water line I look forward to your response. Mark . . .

Assuming the steel boat hull is bare, clean, dry, sound and prepared as detailed in the Technical Data sheet we can recommend Teamac High Performance 2 Pack Zinc Phosphate Primer followed by Teamac High Performance Polyurethane Topcoat.

This is available in clear, or many RAL and BS colours in a gloss finish.

Hi, I currently have a large Zintec roof on my shed (5m x 4m) and when the sun beams down on the raw Zintec coating of the steel, this gets extremely hot and warms the interior of the shed up. im wondering if theres a paint that i . . .

Assuming the Zintec roof is pitched, clean, dry, sound and prepared as detailed in the Technical Data Sheet Eagle DoubleCoat Pro-Reflect Liquid Waterproofing could be used.

This is an aluminium finish which is solar reflective and may aid reducing the heat.

Good afternoon, I am looking to paint a new concrete floor in a double garage and i would like it to be hard wearing and non-slip. Can you please recommend the best solution. Thank you. Tony . . .

Assuming the concrete garage floor is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Rust-Oleum 5300 Epoxyshield Maxx.

For an anti-slip finish Rust-Oleum Epoxyshield Anti-Slip Additive can be used.

If the concrete is new you should allow approximately 4 weeks per inch of slab depth to allow the concrete to dry prior to application.

Hi there, I have a large metal farm chassis trailer that I have just got sand blasted. It is going to be the base for a shepherds hut and will live outside year around. I want to paint it with some good protective paint that will s . . .

Assuming the metal is steel, it is clean, dry, sound and prepared as detailed in the Technical Data sheet we can recommend two coats of Jotun Jotamastic 90 followed by Jotun Hardtop XP.

This is available in many RAL and BS colours in a gloss finish.

I have been advised to use Sigma conseal in black, but cannot find it on your website, can you please help ? . . .

Thank you for the enquiry, is it Jotun Conseal Touch-Up you are looking for? We will contact you directly for more information.

I’m trying to find a clear waterproof finish for a painted rendered wall, the render is on a 1850 year old property with stone walls and I need to bolster the water resistance. Do you have anything that can help? . . .

Assuming the previously painted wall is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Hydron Nu-Guard AG to increase the waterproof properties of the wall.

We would recommended testing for compatibility and adhesion prior to full application.

This will leave a light sheen to the surface.

I have a narrow boat I am fixing the roof which is 57 ft 6ft wide I have prepared the roof which is steel roof and has been primered with a grey rust proof paint. I'm looking for a top coat that is heat risitant. In a oyster white . . .

Thank you for the enquiry, we have contacted you directly for more information.

Which type of paint is for pvc doors pls? Thank you

Assuming the doors are UPVC, they are clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend Zinsser Allcoat Exterior Water Based.

This is available in many RAL and BS colours in a matt, satin or gloss finish.

Hi I’m planning on painting a old cast metal lamppost I’m thinking of a gray or black colour could you send me different shades of colours to look at that would be suitable for this project . . .

Many of the paints we stock are mixed to industry standard RAL and BS colours, unfortunately the manufacturers do not produce colour charts.

We would recommend viewing a RAL colour chart in person to ascertain colour suitability for you project.

Hi. I have iron gutters which are rusting on the inside. I need to coat them in something which will prevent this and will be ok being submerged some of the time. Do you have any products which would work ? Many thanks. . . .

Assuming the gutters are clean, dry, sound, all rust is removed and treated with Coo-Var Rust Converter, they are prepared as detailed in the Technical Data Sheet we can recommend KoverTek TekCryl Instant Repair Roof Kit.

I'm using a Stokes modified acrylic paint containing Xylene - UN 1263 - for coating galvanised steel. I'm interested in a) aquiring whatever your current version of this paint is; b) getting a data sheet for it, including user inst . . .

From your description I would assume you are potentially using Axalta ViterLac 305 Vinyl Acrylic Primer Finish, data sheets can be downloaded from our website.

We have been asked to specify an acid resistant paint for a battery room within a substation building. Can you advise if there are any acid resistant paints that can be used on plasterboard? . . .

Thank you for the enquiry, we have contacted you directly for more information.

Hi I'm looking for a one coat application paint to cover galvanised steel frames for a large hospital job our company is building . The frames will be exposed to the elements , so needs not to peel off . What would you recommend. T . . .

Assuming the galvanised steel is clean, dry, sound and prepared as detailed in the Technical data sheet we can recommend Rust-Oleum Mathys Noxyde Peganox.

This is a self priming topcoat but 2 coats would be recommended.

I am working for a walking charity in the UK and supporting Councils to do more to enhance the walking and cycling environment, especially around schools. I am the artist working on a project to deliver 3 street murals in areas whe . . .

Thank you for the enquiry, we have contacted you directly for more information,

Have you any contractors near hornchurch Essex RM124BJ

Thank you for the enquiry, unfortunately we do not have an approved contractor list.

Hi i have a cladded wooden building that has bean treated with Bird Complete Wood Protector do you have a top coat i could use many thanks Kev . . .

Thank you for the enquiry, we believe this product may contain water repellancy features which may make this not over paintable.

Unfortunately we cannot recommend a product for this application.

is it possible to get masonary paint that is light oak in colour?

Many of our masonry paints such as Wethertex AP77 Flexible Smooth Masonry Paint can be mixed to many RAL and BS colours that may be suitable, but these will not replicate the look of timber.

Hi can combi colour be mixed to any colour? I’m looking for a copper bronze so it can be applied to a motor vehicle, Kind regards R allen . . .

Rust-Oleum CombiColor Original can be mixed to many RAL and BS colours, we would recommend viewing a RAL or BS colour chart in person to ascertain colour suitability.

Hi, I am looking for a yellow coloured durable hard wearing paint to use on cast/ductile iron fire hydrant covers located in a heavily trafficked road, could you advise what would be suitable. . . .

Assuming the cast iron covers are clean, dry, sound and prepared as detailed in the Technical Data sheet we can recommend one coat of Smartkote Protectakote 2K Metal Primer followed by 3 coats of Smartkote Protectakote UVR. This is available in a range of colours including yellow or a clear option.

I have damp at the base of my inside garage wall, no puddles of water or ingress, just damp patches at floor level where the water is clearly penetrating between the ground level blocks and slab. There is standing water on the outs . . .

Assuming the concrete floor is clean, dry, sound and prepared as detailed in the Technical Data Sheet we can recommend 402 Damp Proof Coating.

This can used to provide a surface damp-proof membrane.

For a black bituminous paint you could consider Eagle Black Bituminous Paint.

Which of your exterior waterproof paints would be best for damp ingress on the ground and first floor corner of my white rendered semi? There are no obvious cracks around this corner, so I'm looking for your best white sealant pain . . .

Thank you for the enquiry, we have contacted you directly for more information.

Greetings, I work in a heavy chemical industry and would like to know a few details regarding your coating protection and the range in which it's effective. We have a variety of chemical agents, from chlorine dioxide from hot strea . . .

Thank you for the enquiry, we have contacted you directly.

Hi We want to paint cellar walls white. One wall has effervescence and salt flaking. What is the best paint to use to prevent this happening please? . . .

Assuming the walls are bare, clean, dry, saound and prepared as detailed in the Technical data sheet, we can recommend Zinsser Watertite.

This is available in a range of colours.

I have a very rusty gate, I have been advised to use scrape all rust off and apply rc46 and then order some one can paint, is the correct and which paint do I actually order? Many thanks vicky . . .

Assuming the gates are clean, dry, sound and prepared as detailed in the technical data sheet yes Bradite Fastrac Rust Converter can be used followed by 2 coats of Bradite One Can Matt.

We would recommend to over coat this with 2 coats of Bradite Fastrac.

This is available in many RAL and BS colours in a gloss or satin finish.

Hi, I have a kiln which is going rusty on the outside (it is made of steel). I want to protect it with a heatproof paint. What can you suggest. The internal temperature will get up to about 1300 degrees C The external temp (where t . . .

Assuming the kiln, is in an internal location, not exposed to temperatures over 600°C it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Jotun Solvalitt.

The kiln will require blasting prior to application of the primer Jotun Resist 78 followed by Jotun Solvalitt.

This heat resistant coating will not provide any corrosion protection.

Which of your products is best to improve the look of a felt roof.... thanks

Assuming the felt roof is clean, dry, sound and prepared as detailed in the technical data sheet and you are looking to change the colour of the roof we can recommend Britannia Aquashield Standard.

This is available in black, grey or solar reflective white.

I'm looking for a paint suitable for oven doors, in black or grey. Preferably gloss finish and in aerosol. Do you have such a product? . . .

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Which paint would you recommend for an existing concrete cattery floor?

Thank you for the enquiry, we have contacted you directly for more information

Please advise what oil-based wood preservatives are available to treat a newly erected timber building Thanks in advance Mike . . .

Assuming the timber is clean, dry, sound Sikagard Wood Preserver could be used, this is also suitable to be over painted or stained if required.

Which product do you recommend for exterior concrete paving slabs with heavy foot trafficking.

Assuming the concrete paving slabs are bare, clean, dry, sound and prepared as detailed in the Technical Data sheet we can recommend Smartkote Protectakote UVR Smooth.

This is available in clear, black or white.

If an anti-slip finish is required Smartkote Protectakote UVR could be used, this also has a larger range of colours.

I need to paint some cement board soffit. They are sound but need repainting. I've read on line masonry paint is recommended, which one out of your range would you suggest. I also want yo repaint the textured paint on rest of house . . .

Thank you for the enquiry, we have contacted you directly for more information.

I'm after a pool paint to go on grp. Only 11 square meters. Light blue. Can you help? Thank you

Thank you for the enquiry, we have contacted you directly for more information.

Hello, Can you recommend a product which I may use to waterproof and seal a corrugated garage roof? The roof originally is asbestos construction and I applied Isoflex rubberised paint to it circa five years ago and I am looking for . . .

Assuming the roof and previously applied coating is clean, dry, sound, prepared as detailed in the technical data sheet we can recommend Eagle DoubleCoat Pro-Reflect Liquid Waterproofing.

We would recommend testing for compatibility and adhesion on a small area prior to full application.

Hi. I have a brick house wall that has been painted years ago. The paint has flaked off and the bricks have become porous. Do you recommend any particular products to 1. Provide a water seal and 2. Repaint the old. Thank you. . . .

Thank you for the enquiry, we have contacted you directly for more information.

Can you use rust-oleum on garage door

Rust-Oleum Combicolor Original can be used to paint metal garage doors, depending on the type of metal the required primer will vary.

Assuming the doors are clean, dry, sound and prepared as detailed in the technical data sheet, we would recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion prmier for bare steel areas or Rust-Oleum PVDF Primer for bare galvanised or aluminium areas.

Can CombiColour paint be applied on roller doors on bare metal and also on any remaining existing paint if it sanded to aid bonding? Eddie . . .

Rust-Oleum Combicolor Original can be used to paint metal garage doors, depending on the type of metal the required primer will vary.

Assuming the doors are clean, dry, sound and prepared as detailed in the technical data sheet, we would recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion for bare steel areas or Rust-Oleum PVDF Primer for bare galvanised or aluminium areas.

We would recommend testing for compatibility and adhesion when over painting previously applied paints.

I recall you used to produce paint for concrete garden ornaments and offered them in500ml containers. Is this still the case? . . .

It may be Ardenbrite Metallic Paint you are looking for, unfortunately this is currently unavailable.

Assuming you do not require a metallic finish, the concrete is bare, clean, dry, sound and prepared as detailed in the Technical data sheet we can recommend Coo-Var Acrylic Floor Paint.

This is available in 1ltr, 2.5 or 5ltr tins and can be mixed to many RAL and BS colours.

I want decking paint rust colour or nearest colour thanking you

Thank you for the enquiry, assuming the timber decking is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Osmo Decking-Oil.

This is available in a range of colour options and also sample pots are available - Osmo Decking-Oil Samples.

Can you recommend a solar reflective paint for a plastic roof please.

Assuming you are looking to paint the external areas of the roof, it is polycarbonate, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Britannia Aquashield Eco.

Please be aware that brush marks will be visible through the clear sheeting.

is your Colour PA an acrylic sealer as well as a concrete paint and how far will it go on a new fine concrete surface. . . .

Remmers Color PA (Concrete Acrylic) is extremely weather resistant and completely saponification stable.

The coverage rate for this product is 200ml per m² per coat.

Good afternoon, I have aluminium windows where the powder coating as failed in certain areas, bubbling and blistering. I intend to lift out the frames and sand back the the affected areas to sound paint and metal. Could you please . . .

Assuming the aluminium frames are clean, dry, sound and prepared as detailed in the Technical data sheet we can recommend Technispray Kolorbond K2 Set.

This is available in many RAL and BS colours in 4 different sheen levels.

Hello, do you have a product that will go over bitumen, that was used to fix Marley floor tiles, and that would then be suitable for fixing ceramic tiles using a normal flooring adhesive. Clifford Sullivan . . .

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Hi could you give me some advice on what to use on a bedroom wall which gets damp on it . It's an outside wall and have draws 6-8 in away from the wall. What could I paint on the plaster or bricks to stop the damp from coming throu . . .

Assuming the plastered walls are clean, dry, sound and prepareed as detailed in the technical data sheet we can recommend Coo-Var Anti-Damp Paint.

This can be over painted or have wall coverings applied once fully cured.

Hello, I want to paint ( spray if poss. ) a roller type garage door and wondered what would be the best paint to use? The door is either steel or aluminium but is coated both sides so not 100% sure! The coating appears to be quite . . .

Thank you for the enquiry, we have contacted you directly for more information.

I am looking for something to adhere to rubber base in Van to stop bread crates sliding around and tipping in the back of van . . .

Assuming the rubber is nitrile or chloroprene, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Smartkote Safekote.

This is a bare foot friendly anti-slip paint that may reduce the sliding.

Rust-oleum cupboard matt finish cupboard paint Do you stock this product? Thank you

Thank you for the enquiry, unfortunatley we do not stock this product, but assuming the cupboards are a laminate, clean, dry, sound and prepared as detailed in the techincal data sheet we can recommend Zinsser Bulls Eye 1-2-3 followed by Zinsser Perma-white interior for this application.

Hi I’m due to have the exterior of my house painted but would like some advice as to which paint to choose. It has rough rendering on the walls. Also the cills have a metal edging which is rusting. What is the best solution to st . . .

Thank you for the enquiry, we have contacted you directly for more information.

I want to paint my white upvc door black. What primer do I need? R.

Assuming the upvc door is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Technispray Kolorbond Aquatek.

This can be applied by brush roller or spray application.

There is no primer required but you must clean the uPVC with Technispray VinylKleen, then again with Technispray WindowPrep and finally abrade with a red Scotchbrite before application of Technispray Kolorbond Aquatek.

This then offers a 10 year adhesion guarantee and 5 year colour fastness guarantee.

Good evening, Looking for a suitable product recommendation to paint exterior white sand cement render walls. Currently using Colourtrend exterior white paint but need a more durable paint as I live approx 500 meters from the sea. . . .

Assuming the previously applied paint is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Mathys Murfill Waterproofing Coating.

What's the best paint to apply to garden paving slabs? Something that requires minimal maintenance.

Assuming the concrete paving slabs are only exposed to foot traffic, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Acrylic Floor Paint.

This is available in many RAL and BS colours.

I have traditional garden sheds made from timber, what protection would you recommend?

Assuming you woud like a painted finish, the timber is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zanders PF59 Stain Blocking Primer Finish followed by two coats of Wethertex OT25 Wood-Flex Satin Opaque Timber Paint.

Hi im looking at the cladding paint but unsure on what color I want. Do you sell testers at all? Thanks Kirsty . . .

Unfortunately the manufacturers do not make tester pots, this and many paints are mixed to industry standard RAL and BS paint codes, as stated on the website we show a representation of the colours on the product pages, but these can look difference on various devices.

So we recommend to view a RAL or BS colour chart in person to ascertain colour suitability.

I have just purchased abuilding that has metal cladding - its in good condition but i want to change the colour to anthracite grey. What product would you recommend to use in a spray machine please . . .

Assuming the cladding is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Mathys Metal Cladding Primer followed by Rust-Oleum Mathys Metal Cladding Topcoat.

This is available in many RAL and BS colours in a semi-gloss finish.

What product would you recommend for an asphalt covered walkway ramp from pavement to flats entrance

Assuming you are looking to paint the asphalt, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommed Rust-Oleum Tarmacoat.

Is there a product that I can coat my radiator cover with ( on the inside ) when used with a storage heater to avoid possible fire risks ? . . .

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

looking for green brick and concrete paint for lintels under windows. Can only find in Germany.

Assuming the concrete lintels are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Acrylic Floor Paint.

This is available in many RAL and BS colours in a semi-gloss finish.

I need to touch in ( ie: brush) areas of old weathered paint on a steel car chassis. The colour is approximately BS 381 671 in a semi Matt finish - it is an enamel of some sort. What can you offer. I probably won't need more than o . . .

Assuming the chassis is steel, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 7500 Alkythane.

Any bare steel areas should be primed with Rust-Oleum 769/780 Damp-Proof Rust Primer prior to application.

We would recommend testing for compatibility and adhesion prior to application.

how far does paint cover ie concrete paint per litre ?

Thank you for the enquiry, we have contacted you directly for more information.

Hi I’m looking to cover a set of patio doors from light oak to a dark grey for use in a garden building. They are currently not fitted and the glass is not in yet. I have a spray compressor, what would you recommend please? Many . . .

Thank you for the enquiry, we have contacted you directly for more information.

Could you advise us on a paint that is suitable for an outside deck area. ( inherited) It is already painted and is flaking and in need of restoration. Look forward to your advice. Susan Johnston . . .

Thank you for the enquiry, we have contacted you directly for more information.

Hi, I want to test a white satin upvc paint before purchase, can I buy a test pot please Thanks Dawn

Unfortunately the manufacturers do not produce tester pots.

This and many paints are mixed to industry standard RAL and BS paint codes, as stated on the website we show a representation of the colours on the product pages, but these can look difference on various devices.

So we recommend to view a RAL or BS colour chart in person to ascertain colour suitability.

Good morning I am a site manager at a school we have a tongue and groove wooden out building that houses our Hydro Pool. I was wondering what paint to use on the exterior? At the moment its stained in a dark oak but I would like to . . .

Assuming the timber is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zanders PF59 Stain Blocking Primer Finish followed by 2 coats of Wethertex OT25 Wood-Flex Satin Opaque Timber Paint.

This can be mixed to many RAL and BS colours.

Am applying Hammerite Metallic paint to metallic garden chairs and wonder what is the best liquid for cleaning the brushes. e.g. Can I use turps? . . .

Unfortunately we do not stock Hammerite, we would recommend looking on the products technical data sheet for this information.

I am thinking of having my roof of cement tiles cleaned treated &repainted how ever painting roof tiles seems to be a controversial subject even among roofers could you advise on which type of paint & primer to use & if . . .

Assuming the fibre cement tiles are bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Cromar Renocoat Roof Tile Renovation Paint.

This does not require a primer, but two coats should be applied.

Can I use coo card radiator enamel on electric storage heaters Thanks Michelle

Coo-Var Radiator Enamel will take a temperature up to 150°C but as we don’t know what actual surface temperature a night storage type heater will get up to we can’t say for sure if the paint will be OK on any particular storage heater, it could depend on the model, type etc.

You will need to check with the manufacturer to find out what the surface temperature of their particular heater will get to during use.

(As they are the manufacturer they must know what temperature the surface of the heater gets up to during use). If it is below 150°C then the paint can be used.

I Painted a pharmacuetical factory with a 3 part paint on concrete floor. This was the medium,catalyst and thinner or hardener .I have been struggling to find this type of paint because I cant recall the manufacturer from Bolton. I . . .

Thank you for the enquiry, we have contacted you directly for more information.

Where can I get a colour chart, please?

Many of the paints we stock are mixed to industry standard RAL and BS paint codes, as stated on the website we show a representation of the colours on the website, but these can look difference on various devices.

So we recommend to view a RAL or BS colour chart in person to ascertain colour suitability.

These are for sale here.

do you do tester pots? I'd like After Diner and Art School please.

Thank you for the enquiry, we have contacted you directly.

Good morning. We are a lighting manufacturer and have an application where some suspended linear aluminium light fittings will be required in RAL 3014-Antique Pink. This will be to powder coat the light fitiing bodies. Do you stock . . .

Thank you for the enquiry, unfortunately we do not currently stock powder coating materials.

Please advise a suitable paint to apply on a new lime render the area is approx 20 sq m

Assuming the lime render is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Keim Royalan.

The first coat will be Keim Royalan Dilution onto the bare lime render, 2nd coat will be Keim Royalan Grob diluted 20% with Keim Royalan Dilution and the final coat will be Keim Royalan in the chosen colour.

Hi, I would like help on what cleaner you recommend on upvc and I would like a litre of anthracite for the windows. I have just opened a business and would like some more information on yoire supply. How long does delivery normally . . .

Thank you for the enquiry, we have contacted you directly with more infomration regarding the Kolorbond options for UPVC , these are normally available for 2-3 working day deliveries.

These and many of the paints we stock are mixed to industry standard RAL and BS colours and swatch charts are available here.

Please advise best paint solution to apply to the interior (plastered) faces of Victorian London Stock brickwork to reduce heat loss. . . .

Thank you for the enqiury, unfortunately we do not have a product to recommend for this application to reduce heat loss.

Paint for microwave inner coting

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Do you have a colour card for upvc cladding paint please? I am after a beige/grey/sage shade that is neutral . . .

You are able to purchase RAL, BS and NCS colour charts on our website HERE

I have an internal step to my kitchen. The front facing part is metal which is rusted. The rusted metal is approximately .75 m long x 3 cm width. Obviously, I don't want to buy huge tins of primer and top coat for this small area. . . .

Assuming the step is steel, rust is removed, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Smartkote Safekote.

We would recommend priming prior to application with Smartkote Protectakote 2K Metal Primer.

This is a barefoot friendly anti-slip floor paint.

Hi I have a slate exterior frontage which gets slippery after rain. Which anti-slip preparation would be the best to use on this surface please? . . .

Assuming the slate floor is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Smartkote Protectakote UVR.

This is available in a range of colours and a clear option.

The first coat should be diluted 10% with Xylene.

Hi I was looking for an insulating paint that I can put on a concrete wall between our paper machine and an electrical room on the other side of the wall, Your website mentions lots of paints available but I can only see fillers on . . .

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Hi, I have just had new grey door fitted and now need to revamp my stone doorstep to match the colour. I've always used traditional red doorstep paint before, What would be the best type of paint for this purpose. Thank you . . .

Assuming the stone door step is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Acrylic Floor Paint.

This can be mixed to many RAL and BS colours.

Hi, I have a shower room which is fully tiled, floor and walls. There must be a problem on the one side as the wall on the other side is damp and the plaster is coming off up to 30ins from the floor. They are large wall tiles on th . . .

Thank you for the enquiry, we have contacted you directly for more information

Which paint should I use on a kitchen floor over ceramic tiles? Thank you for your help.

We would recommend the tiles be primed with Smartkote Protectakote Clear Primer Treatment followed by 2 coats of Smartkote Safekote.

what paint will cover a upvc decking in an ivory colour

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Looking for the best match to paint my rosewood grp door. Seen ral8017 as rosewood/chocolate brown on a company site that sprays them. I had zinnser in 8016 and that was way off. Do you have any suggestions of the best match/paint? . . .

Thank you for the enquiry, we would recommend looking at a RAL or BS colour swatch chart in person to ascertain suitability of any colour for your application.

Trying to place an order for 2x5ltr Rust-Oleum Mathys Noxyde Pegarust- Colour Black. Cannot find on your website. Want to spend approx £175.00. Cannot order. Please advise . . .

Thank you for the enquiry , please follow this link Rust-Oleum Mathys Noxyde Pegarust.

can it be applied by a mini roller

Thank you for the enquiry, we have contacted you for more information.

Hello could you recommend a paint to use on a steel fire brazier/cooker that is rust proof and can withstand very high temperatures. i painted it with the "no nonsense" 600 degree Celsius paint and within a month it cracked off and . . .

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Hi, I've primed a narrowboat with white spirit based zinc phosphate. Do you have an enamel product that can go over this primer? . . .

Assuming prior to full application you test for compatibility and adhesion, the areas to be painted are above the waterline, clean, dry, sound, prepared as detailed in the technical data sheet we can recommend Teamac Marine Gloss.

Need a paint that would stay on golf driving range balls. Only use best quality but players are taking all prov Sri on and the best need to make them all yellow any suggestions please it is costing me to much regards job . . .

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Hi - we are looking for a paint that gives a SATIN finish on to a metal boat. The paint is for exterior use, on the sides, so it won't be walked on or immersed in water. For application with a brush or roller. Smooth finish needed. . . .

Thank you for the enquiry we have contacted you directly for more information.

I am looking for a coloured screed to apply to a community library office, kitchen and toilet areas. The floor area is approx 35 sq m and is concrete with some remnants of old plastic tile adhesive still visible. The product thickn . . .

Thank you for the enquiry we have contacted you directly for more information.

Hi, i’m ready to paint my workshop walls and floor. I’d like a scrubbable / washable paint for both the walls and floor that will resist oils / greases / petrol and the likes. I strip / build chainsaws and small engines. I’m . . .

Assuming the floor and walls are clean, dry ,sound and prepared as detailed in the technical data sheet we can recommend Bradite HD Floor & Wall.

We would recommend the floor is ground prior to application.

I am interested in knowing more about the Rusoleum range of paints suitable for painting kitchen cupboards. Is a colour chart available, please? . . .

Thank you for the enquiry, unfortunately the manufacturer does not make colour charts, we have contacted you directly.

Hi. I have a domestic garage (31sqm) with a weak mixed screeded floor. This has then been painted with a Horrace & Williams (now Serene Paints) 1 pack paint straight onto the screed (mistake). Unfortunately the paint lifts easi . . .

We would recommend the concrete floor is ground prior to attempting to apply any paint.

Assuming this is done the floor is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 5300 Epoxyshield Maxx.

I'm looking for an exterior paint & primer for use on precast concrete wall panels on a single story tennis club buiding and would appreciate some technical advise pr prepartion. priming and paint requirments as well as costs . . .

Thank you for the enquiry, assuming the concrete panels are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Wethertex ST1 Quick Dry Stabilising Primer followed by 2 coats of Wethertex AP77 Flexible Smooth Masonry Paint.

best paint for using on new galvanized sheet roofing.

Assuming the new galvanised roof sheeting is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Mathys Pegalink Universal Adhesion Primer followed by 2 coats of Rust-Oleum Mathys Noxyde.

Hello there , can you recommend a spray matt RAL 1001 for spraying stainless steel legs please ?

Thank you for the enquiry we have contacted you directly for more information.

where are my samples I have ordered

Thank you for the enquiry, we have contacted you directly for more information.

I am very interested in your Garage Epoxy Floor Paint I have a double garage size 5.3 X 5.4. Please recommend one of your Epoxy Floor Paints for this jop. If you would please use my email address I will be able to get back to you s . . .

Thank you for the enquiry, we have contacted you directly for more information.

Hi, im looking to paint repair a flat fiberglass flat roof which is in good condition. The roof is 20x13 ft which is around 25MSq. Can you advise on your selection which is the best and a reasonable costing please. . . .

Thank you for the enquiry, we have contacted you directly for more information.

I will be blasting a beam and columns inside a warehouse and the base coat will be sherwin Williams 5090. I’m looking for a compatible primer. Could you advise please. Thank you . . .

Assuming you are applying Sherwin-Williams Firetex FX5090 a compatible primer would be Sherwin-Williams Macropoxy 400.

looking for non slip decking paint to use safely over KOI KARP pond

Thank you for the enquiry, we have contacted you directly for more information.

is rust olium suitable for chrome plated sink plug hole

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

I would like a recommendation for an epoxy floor paint to seal a concrete floor and the adhesive residue left behind after the removal of Lino floor tiles which contained asbestos. . . .

Thank you for the enquiry, unfortunately we do not have a product to recommend for application over the adhesive residue, this would have to be removed prior to preparation and application.

We have contacted you directly for more information.

What do I use on galvanised metal for primer & topcoat?

Thank you for the enquiry, we have contacted you directly for more information.

Hi I have a cast metal crome Coated finnished the trophy that can't be cleaned up so haveing to paint I don't know if this can be done and would you be best paint . . .

Thank you for the enquiry, unfortunately we do not have a product to recommend for application to chrome.

Hi, Looking for a paint to cover exposed heating pipes and galvanised conduits. Thanks Claire

Thank you for the enquiry, we have emailed you directly for more information.

I am looking to spay paint white high gloss wood kitchen doors can you recommend a good primer, white paint and a top coat lacquer . . .

Assuming the previously painted wooden kitchen doors are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Technispray Kolorbond Aquatek assuming you require a satin finish.

No Clear lacquer would be required.

What is the best paint to cover pebble dash?

Assuming the pebble dash is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Wethertex AP77 Flexible Smooth Masonry Paint.

Hi, trying to decide between rustoleum furniture paint or kitchen cabinet paint. What's the difference? It's for a sewing machine table so need hard wearing, thanks . . .

Rust-Oleum Matt Chalky Kitchen Cupboard Paint is not recommended for use on worktops, Rust-Oleum Matt Furniture Paint is hardwearing and water resistant, assuming the table is clean, dry, sound and prepared as detailed in the the technical data sheet we would recommend this.

Please be aware that any matt finish paint is less hardwearing than a satin or gloss finish and as it wears may leave shiny patches.

I need a strong paint for my metal tables and chairs for the garden

Assuming the metal is steel, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by 2 coats of Rust-Oleum CombiColor Original.

I need to paint two metal posts on the patio (external) and would like them to match the frames of the adjacent uPVC windows which are framed in Golden Oak. Please can you recommend a suitable paint? Thank you. . . .

Assuming the posts are bare steel, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by two coats of Rust-Oleum CombiColor Original.

This can be mixed to many RAL and BS colours.

Thank you for your answer (below) to my question (also below) but I was also asking what colour you have which would match Golden Oak window frames, please? I need to paint two metal posts on the patio (external) and would like the . . .

Unfortunately we cannot recommend a colour to match, we would recommend to view a RAL or BS colour chart in person to ascertain colour suitability.

Please recommend a paint suitable for a softwood 5 bar outdoor driveway gate, colour white. And primer, undercoat paints if necessary. . . .

Assuming the timber gate is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend priming first with Zinsser Cover Stain then applying Zinsser Allcoat Exterior (Water Based).

I need to re-paint window sills and door surrounds throughout the house. Trouble is they are all oil based painted surfaces. I'd prefer oil based again. Where can I buy that? I would need maybe 10 litres of antique white. . . .

Assuming the door surrounds and window sills are previously painted timber, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser Allcoat Exterior (Solvent based).

We would recommend testing for compatibility and adhesion prior to full application on any previously applied paints.

If there are any areas of bare timber these should be primed with Zinsser Cover Stain.

Hi , Could you tell me if you have a clear anti-slip coating for black limestone flags? .. We have a sloped driveway which people also use as the footpath to the house so I am a little concerned that it would be slippery when the w . . .

Smartkote Protectakote UVR does not mention sandstone as a specific substrate it can be applied to, but Smartkote Protectakote Clear Primer Treatment can be used to prepare inorganic surfaces for the subsequent adhesion of Smartkote Protectakote UVR and would be worth testing as an option to meet your requirements.

Are these paints sprayable. I manufacture ornamental ironwork.

We have contacted you directly for more information.

Hi My house has some patches where the exterior paint has flaked off. Is there anywhere I could send samples for texture / colour matching - the paint is a much heavier texture than say Sandtex. Please advise Tim Hill . . .

Thank you for the enquiry, unfortunately we do not offer an colour or texture matching service.

Many of our paints can be mixed to many RAL and BS colours.

Assuming the substrate of the walls are compatible, clean, dry, sound and prepared as detailed in the technical data sheet Wethertex LD77 / HD77 Pliolite Wall Coating could be considered as it has two texture options.

Hi, I am hoping you can help me, I am looking for a recommendation for a clear water repellent that can be applied to external painted walls & that can be painted over in 5-10yrs??? Fingers crossed . . .

Unfortunately we do not have a clear sealer product to recommend for application over a painted substrate.

But assuming a painted finish is suitable, the previously painted substrate is clean, dry, sound and prepared as detailed in the technical data sheet we can reccomend Rust-Oleum Mathys Murfill Waterproofing Coating.

We would recommend testing for compatibility and adhesion prior to full application.

I have previously used Trebitt on my wooden buildings, is it still available in the UK?

Unfortunately this product is not available in the UK.

As an alternative we can recommend Remmers Aqua MSL-45/sm Medium Build Stain UV+.

This is also a water based stain for internal or external applications.

Which paint would you recommend for my interior doors in shade ral 7016 , I want a Matt finish ?

Assuming the doors are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Bradite One Can Matt.

The technical data sheet can be found in the data sheets tab on teh product page.

This is available in many RAL and BS colours, including RAL 7016.

Would your combi primer and coat option be suitable for painting a transit van?

Assuming is emquiry is referring to Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion and Rust-Oleum CombiColor Original, the previously painted surface is clean, dry, sound and prepared as detailed in the technical data sheet they may be used for this application.

These products are designed for light industrial applications where anti-corrosive primers and topcoats are required, but these are not classed as automotive paints specifically for use on vehicles.

However customers have had good results with this products when applied to hobby vehicles, although it is not something we or the manufacturer can offically support.

We would recommend testing for compatibility and adhesion on any previously painted substrates prior to application.

Need to rejuvenate exterior dormer wood cladding which looks like its been possibly painted with a fench kind of brown stain. Would like to change the colour if possible also . . .

For this application we would recommend using an opaque system rather than a stain, otherwise you will be able to see the underlying previously applied brown stain you are looking to move away from.

Assuming the timber is clean, dry, sound and prepared as detailed in the technical data sheet we can recommed Zinsser Cover Stain followed by Zinsser Allcoat Exterior.

This is available in many RAL and BS colours in a matt, satin or gloss finish.

I am looking for a heat resistant paint that is also waterproof. My front door is south facing therefore gets all weather thrown at it. Could you advise a paint that would be suitable to use? . . .

Assuming the door is UPVC, composite or timber, the heat resistance required is in relation to direct sunlight rather than another source of heat, the door is clean, dry, sound and prepared as detailed in the technical data sheet, we can recommend Zinsser Allcoat Exterior Water Based.

This can be mixed to many RAL and BS colours and is available in matt, satin or a gloss finish.

hi I have a old tiled roof which I jet washed off because it had all moss over it but its taken all the old surface off now. Which paint is best to cover it with in grey? . . .

Assuming the roof tiles are clean, dry, sound and prepared as detailed in the technical data sheet Cromar Renocoat Roof Tile Renovation Paint could be used.

This provides an external decorative and protective finish.

It is available in slate grey, red or dark brown.

I need an etching primer for aluminium on a boat. What would you recommend? Thanks, Bill

Thank you for the enquiry, we have numerous options for this application but we will need more information regarding which areas of the boat are to be painted and what products are to be used in conjunction with this.

I need to paint window sills that are under a tree and are attacked by acidic sap, the sills are cement based and are currently painted with a water based exterior paint. What product can i used to defend the finish against the aci . . .

Assuming the previously painted window sills are clean, dry, sound and prepard as detailed in the technical data sheet we can recommend Coo-Var P101 Anti-Graffiti Coating.

This is suitable for application over water based paints once cleaned and lightly sanded, but we would recommend testing for compatibiltiy and adhesion prior to full application.

This would provide the best resistance to acidic sap and can be cleaned many times without effecting the coating.

I intend to apply primer and finishing coats to bare mdf using a spray gun. Can you advise which furniture paints that would be suitable? Thanks . . .

For this application assuming the MDF is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend HMG Pre Cat Primefast 2014-04 followed by HMG Acid Cat MB Colours.

This is available in many RAL and BS colours in a matt, satin or gloss finish.

Prior to application do not scuff or roughen the MDF as this will release waxes in the MDF which could affect adhesion.

Rusted industrial gutters . Which is the best paint / system to add protective coat . How many years before requires reapplication ? . . .

Assuming this is a steel or galvanised valley gutter and you are looking to paint the inside, it is clean, dry, sound and the corrosion is removed prior to application we can recommend Jotun Jotamastic Smart Pack HB.

This would require 2 coats to be applied.

Hi I have steps leading to front door which have been professionally asphalted 20 years ago. We now have a damp penetration issue and are looking for a suitable solvent based quick drying seal coat which will be invisible , matt or . . .

Thank you for the enquiry, unfortunately we do not have a product we can recommmend to solve a damp penetration issue on asphalt.

Morning Looking for the following Paint in the smallest quantities you provide, can you advise availability and cost if you can supply this. Marine Paint- RAL1004 Yellow RAL 3020 Red RAL 9003 White . . .

Thank you for the enquiry, the smallest tin size in a marine paint would be 1ltr tins.

We would need more information regarding the project to ascertain which product will be suitable for your specific application.

Please provide more information to [email protected]

what paint would i need for damp proofing a caravan inside

Thank you for the enquiry, we will need more information regarding the cause of the damp and the substrates you are looking to paint to assist with a recommendation.

We have contacted you directly for more information.

Hello, I need a very good black paint for wooden stairs (wooden steps), I would like to buy a good quality anti-slip paint, these are stairs in a restaurant, I need 3 pairs of stairs and wooden platforms, thank you . . .

Assuming the timber stairs are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Smartkote Protectakote UVR.

Please be aware that anti-slip paints can make the areas painted harder to clean, if this is an issue you could consider Smartkote Safekote.

This is a less aggressive anti-slip which is easier to clean and suitable for bare feet.

I require a RAL 9007 paint for outdoor plywood. Can you guide me I can't find the right colour on your website. . . .

RAL 9007 is a metallic finish, unfortunately we do not have a product to recommend for application to timber in RAL 9007 but Blackfriar Metallic Paint is available in a silver finish.

Looking for a suitable white paint for the interior of a summer house (which will help stop mould and mildew forming) Thanks . . .

Assuming the interior is previously painted, clean,dry, sound and prepared as detailed in the technical data sheet we can reocmmend Zinsser Perma-White Interior.

This can be mixed to many RAL and BS colours.

Any bare timber areas should be primed with Zinsser Cover Stain.

Hi, I am looking for a paint RAL9007 with non metallic components. Is there something in your shop which I can go for? The paint composition needs to be non metallic because it is going to cover a antenna and it can cause interfere . . .

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Hi Could you recommend paint for new untreated concrete base which is external (greenhouse base) Thanks

Assuming the concrete base has a damp proof membrane, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Acrylic Floor Paint.

This is available in many RAL and BS colours in a semi gloss finish.

We would recommend if the concrete slab is new it is left approximately 4 weeks per inch of slab depth prior to preparation by grinding or acid etching before applying the paint.

I am after a paint to apply to ready painted metal parts for external use in RAL7035 Matt os Satin finish. What do you recommend? . . .

Assuming the metal parts are not subject to traffic, not exposed to chemicals, or submerged, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 7500 Alkythane.

This is available in many RAL and BS colours, we would recommend testing for compatibility and adhesion prior to full application.

I need the technical data sheet for Elastadeck Walkway topcoat basis. Cannot find on your website to download, please advise. Also is it advisable to lay some fibreglass matting before application . . .

Assuming you are looking for Tor Elastadeck Sealer Coat's technical data sheet, this can be found on the product page in the datasheets tab.

Hi, I’d like to buy some of your paint. Where can I buy it? Thank you, Julie J

Thank you for the enquiry, you can place an order on our website .

These can be delivered to most mainland uk addresses or collection from our trade counter in Leeds.

I have an internal brick wall which must be allowed to breathe to prevent damp. Does chalk paint have microporosity? Colin MORTON oes oes . . .

The Rust-Oleum Chalky Finish Wall Paint is a durable and scrubbable paint but does not state it is breathable.

Assuming the internal wall is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Keim Optil for a highly vapour permeable option.

I'm looking for a waterproof paint for the concrete steps in front of our house. preferably a sandy/brick colour to merge with the adjacent wall bricks. Please advise . . .

Assuming you are looking for a waterproof paint to also address water getting in under the steps, the area is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend KoverTek TekPur Waterproof Balcony Kit, but this is only available in grey.

If the paint is purely for external application to concrete steps in a domestic application with no waterproof nature required for the structure we can recommend Coo-Var Acrylic Floor Paint.

This can be mixed in many RAL and BS colours.

Which paint do you recommend for metal staircase high traffic staircase in oily environment

Assuming the staircase is internal, it can be sandblasted to SA2.5, any oil contamination is removed and it is prepared as detailed in the technical data sheet we can recommend 304 HD Epoxy Floor Coating.

This is available in a range of colours in a gloss finish.

Anti-slip additives can be added if required.

what masonry paint can i use over weathertex hbs to maintain max breathability

Assuming the Wethertex HBS Flex-Coat Hi-Build Coating is clean, dry, sound and prepared as detailed in the technical data sheet we would recommend Wethertex AP77 Flexible Smooth Masonry Paint.

Hi i am looking for some anti graffiti paint. but it seems that it is out of stock on your website. we are looking for coloured paint and not clear. Please advise. Many thanks. . . .

Hydron Nu-Guard AG is available in clear and a standard range of colours.

If you are applying this to concrete or very porous surfaces priming with Hydron Nu-Guard WB Concrete Sealer may be required.

I have a metal garage door which is currently dark green in colour. I wish to repaint it Chartwell green. What undercoat should I use? Many thanks . . .

Assuming the previously painted metal door is clean,dry, sound and prepared as detailed in the technical data sheet we can recommend two coats of Rust-Oleum CombiColor Original - Chartwell Green, no undercoat would be required.

Hi, Please can you tell me if the kitchen cupboard paint is oil or water based? Can you also tell me if it can be used with a spray gun? Thanks in advance and best wishes Steph . . .

Rust-Oleum Matt Chalky Kitchen Cupboard Paint's are water based.

Do you have a Black 9005 - 30% gloss (mat) paint for direct application to primed metal? Many thanks

Rust-Oleum CombiColor Original can be applied directly to metal in some circumstances, this is available in a matt finish in Ready mixed Black which is close to RAL 9005.

Hi. Can the furniture paint be used in a spray gun Thanks

Assuming this enquiry is about Rust-Oleum Matt Furniture Paint, unfortunatley these are not suitable for spray application, but as an alternative you could consider HMG Pre Cat AV Colours.

This is available in many RAL and BS colours in a range of finishes.

Is it possible to coat as corrugated asbestos roof with a waterproof sealant. Cannot afford the £1200 cost of replacing the roof and then the cost of boarding and insulating the garage on top of that. . . .

Assuming the asbestos corrugated roof is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Eagle Bitumen Primer followed by Eagle DoubleCoat Pro-Reflect Liquid Waterproofing.

I am about to purchase a Grade 2 listed cottage. It needs decorating through out but the paint I use must be breathable. The conservation department recommend Lime wash but I like the look of the chalky wall paint. Is the paint bre . . .

If this enquiry is regarding Rust-Oleum Chalky Wall Paint, unfortunately no this paint is not stated to be breathable.

Assuming you are looking for a breathable / vapour permeable paint for internal application you could consider Keim Optil.

I have a small garden shed 6x8 feet about 20 years old. No cracks in asbestos roof but water now seeps through sheets. Which is the most suitable product to make waterproof? Many thanks. . . .

Assuming the asbestos roof is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Eagle Bitumen Primer followed by Eagle DoubleCoat Pro-Reflect Liquid Waterproofing.

I have a flat roof with parapet walls on two sides topped with coping stones. The coping stones have been painted to matched rendered walls below. I suspect that the stones are no longer totally waterproof. Can these be waterproofe . . .

Unfortunately we cannot match a Sandtex colour, but we can mix many paints to many RAL and BS colours, but not for this application.

Assuming the coping stones are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Britannia Aquashield Eco.

This is available in black, grey or solar reflective white.

Hi I’m looking to paint a wooden dining table can you suggest what paint to use?

Assuming the table is to be painted is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend HMG Supersheen.

This is a two pack paint which can be brush rooler or spray applied, if it is to be applied by any spray application method this should be undertaken with the appropriate PPE and in a spray booth.

This can be mixed to many RAL and BS colours in a satin finish.

Just wanted to check if there is a good quality white paint that I can use for both overpainting scratches on radiators and also painting external upvc door handles. Many thanks John. . . .

Thank you for the enquiry, assuming the upvc door handles are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 9200 Rust-O-Thane.

For the radiators assuming they are white we can recommend Coo-Var Radiator Enamel.

How do you apply Fire varnish base and fire varnish overcoat Brush or roller (foam or other)

These products can be applied by brush, roller or spray application.

Regarding roller choice we would suggest a medium pile Roller Sleeves.

Looking for a paint for a ceiling exposed to steam (heat) not continuously but for periods of 10 minutes 4/5 times daily. . . .

Assuming this ceiling is in a bathroom above a shower, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser Perma-White Interior.

This is suitable for high humidity areas and is available in many RAL and BS colours.

Could you please advise which are the best primer paints to use on a vinyl wallpaper covered ceiling.

We would recommend removal of the wall paper and the adhesive residue prior to application of Zinsser Gardz followed by Zinsser Perma-White Interior.

This is available in many RAL and BS colours.

Hello have question do you have product that you can recommend to spray galvanised roller shutters

Assuming the galvanised shutters are weathered, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Bradite One Can Matt followed by Bradite Fastrac.

This is avaialble in many RAL and BS colours in a satin or gloss finish.

Please be aware that any paint coating applied may wear on the joints of a roller shutter and the faces when they door is rolled onto the drum.

which product is best for garage floor

Assuming this is for a domestic garage floor, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend the Rust-Oleum Epoxyshield Garage Floor Coating Kit.

Do you make a hammered finish goose grey metal paint?

We do not have a hammered finish paint that can be mixed to Goose Grey, but HMG Hammer Finish QAD is available in a range of colours.

i have a fibre glass water feature with a bronze type finish what would i need to tidy it up please

Thank you for the enquiry, we have contacted you directly for more information.

Can your triple thick primer be used as a bedding sand to refusal coat for a gripper coat for tile installation with thinset? (Exterior walkway that has a 100% acrylic elastomeric coating over plywood) . . .

Thank you for the enqiury, we have contacted you directly for more information.

I am painting my narrowboat which paint do I need

Thank you for the enqiury, we will require more information to assist with specification, please send the information below to [email protected]

What is the boat made of?

Are the areas to be painted bare or previously painted?

What methods of preparation can be under taken?

Which areas of the boat are to be paint, above or below the water line or the decks?

Is the boat requiring antifouling?

What colours and finish do you require?

Hello, We have a large (16'x16') shed with a grey felt roof and I wondered whether you had a green paint that would be suitable for felt? Many thanks . . .

Thank you for the enquiry, unfortunately we do not have a roof paint that is available in green, if black, grey or white is suitable and the felt roof is clean, dry, sound, it is prepared as detailed in the technical data sheet Britannia Aquashield Standard could be used.

Which of your paints (white) would you recommend for external quality MDF (Medite) posts supporting a terrace close to the shore. They won't be in direct contact with sea water but are in a marine environment. Thanks. . . .

Thank you for the enquiry, we have contacted you for more information.

Hi, can you recommend a paint for a metal up and over garage door? It's currently mostly painted and whilst I will remove the loose paint I'd rather not have to remove it all. Some galvanized steel is showing. I'm happy to use a pr . . .

Thank you for the enqiury, assuming all the loose or flaking paint is removed, the sustrate is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Bradite One Can Matt.

We would recommend testing for compatibility and adhesion on previously applied paints.

A matt finish is more susceptible to scuffs, stains and water marks, so if a more hardwearing option with a sheen is acceptable Bradite One Can Eggshell could be used.

For the corrugated concrete or asbsetos roof assuming this is also clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Mathys Primer 44 HS followed by Rust-Oleum Mathys Fillcoat.

This is available in light grey, dark grey or black.

Good Afternoon I have a gas fireplace with marble sides and base that has a wood mantle and is framed in wood. I am renovating and would like to paint the wood white. Please let me know what kind of paint to use as a finishing pain . . .

Assuming the timber is bare, it is not exposed to temperatures over 70°C it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser Cover Stain followed by Zinsser Perma-White Interior.

This is available in many RAL and BS colours in a matt or satin finish.

This is a scrubbable paint suitable for high humidity areas.

Hi Ive got a number of Workshop industrial doors that now need retreating, they were originally factory finish, but now the coating has deteriorated. Regards . . .

Thank you for the enquiry, we have contacted you directly for more information.

Hi want to make corrugated asbestos garage roof safe. How much will i need. For single garage.. Cost and delivered to manchester. Vat included. . . .

Assuming you are looking to seal or encapsulate the asbestos roof, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Teamac Acrylic Roof Coating.

This product covers 7 to 12m² per litre per coat.

Two coats are recommended.

Do you have the okon s-40 clear sealer in stock

This is not a product we stock, assuming you are looking for a masonry water repellant treatment we can recommend Hydron Nu-Cryl WRS.

How do I know that it's condensation l have in the corner of my living room

We have a detailed blog post on this subject regarding if it is damp or condensation with recommended products, you can find this here.

Condensation is caused by a lack of air flow and is usually found near windows.

I want to paint over vinyl wallpaper in any color I choose, what product should I get?

For this application we would recommend testing for compatibiltiy and adhesion prior to full application.

Assuming this is done, the wall paper is clean, dry, sound and prepared as detailed in the technical data sheet we can recomemnd Zinsser Bulls Eye 1-2-3 followed by Zinsser Perma-White Interior.

This is available in many RAL and BS colours in a matt or satin finish.

Am i correct to say theres only one paint to make safe corragated asbestos. Also can i put 2 applications on?. How much will i need for a single car garage roof . . .

Assuming you are looking to seal or encapsulate the asbestos roof, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Teamac Acrylic Roof Coating.

This product covers 7 to 12m² per litre per coat.

Two coats are recommended.

I have a patch of damp on a wall caused by hygroscopic salts and I need to sand and repaint the surface with one of your products. Can you recommend which product I should use? . . .

Thank you for the enquiry, we have contacted you directly for more information.

Boiler Peep hole painting required with high resistance paint which one is good quality.

Thank you for the enqiury, we have contacted you directly for more information.

Hello, I was hoping you could assist with the selection of the correct paint for a ceiling suffering flaking paint, damp & condensation. This is due to a small amount of steady water ingress from a faulty chimney/chimney flashi . . .

Thank you for the enquiry, we would not recommend painting the area till the cause of the leak has been found and fixed.

Once this has been done, the ceiling has dried out, it is clean, dry, sound and prepared as detailed in the technical data sheet Zinsser Perma-White Interior.

Hi,I am site manager in a school and need to paint over our suspended ceiling tiles ,some having water marks on . can you give me products that are suitable. . . .

Assuming the suspended ceiling tiles are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser AllCoat Interior (Solvent-Based).

This can be applied by brush, roller, pad or airless spray and is available in many RAL and BS colours.

Hi I am an antique restorer and am using Trymite low temperature acrylic stoving full gloss finish paint and as they are/have stoped producing this I am looking for a new supplier . . .

Thank you for the enquiry, if you are looking for an acrylic stoving enamel, HMG Acrylic Stoving Enamel may be suitable.

This cures in 30mins at 120°C this is available in many RAL and BS colours in a matt, satin or gloss finish.

Paint suitable for painting narrow boat over a rust stabilizing product. Can any be applied successfully in winter? . . .

Thank you for the enquiry, we have contacted you directly for more information.

Hi Do you have a white satin paint suitable for the front metal panel of a Dimplex storage radiator.. Thanks very much Peter . . .

Blackfriar Quick Drying Radiator Paint will take a temperature up to 150°C but as we don’t know what actual surface temperature a night storage type heater will get up to we can’t say for sure if the paint will be OK on any particular storage heater, it could depend on the model, type etc.

You will need to check with Dimplex to find out what the surface temperature of their particular heater will get to during use.

(As they are the manufacturer they must know what temperature the surface of the heater gets up to during use).

If it is below 150°C then the paint can be used.

I am looking for a quality garage floor paint for a double garage which is going to used as a ‘man cave’. Not sure which would be the best product for this and need some help/ . . .

Assuming there is no vehicle traffic on the garage floor, it is bare concrete, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Bradite Floor-It.

This is available in many RAL and BS colours in a semi-gloss finish.

I am looking for a dark green/olive shade in mat for galvanised roof sheets to blend into the background of a hedgerow. Any suggestions? . . .

Assuming the galvanised roof sheets are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Tikkurila Temadur 10.

This would require three coats with the first coat thinned 15% with Tikkurila Thinner 1048.

This can be mixed to many RAL and BS colours in a matt finish.

Assuming the galvanising is in good condition typically prepared by through cleaning with Tikkurila Panssaripesu Roof Cleaning Agent.

Once thoroughly cleaned we generally recommend that the surfaces are abraded with non-metallic abrasive to form a ‘key’ and to remove any zinc oxidation (white salts).

Hi - I have a stainless instoor stauiinless steel fridge with bad scrubber scratches on the front doors which I wish to paint over (they wont polish or silicon sand out). What is best to use please. . . .

Thank you for the enqiury, unfortnuately we do not have a product to recommend for this application.

I have a 5 year old fibreglass type flat roof of about 20 sq. m. The roof is in good condition, no leaks, but solar finish wearing. Which product would be best suited for this type of construction please ? . . .

Assuming the fibreglass roof is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Britannia Aquashield Eco.

This is available in black, grey, or solar reflective white.

good afternoon im looking for grey paint to paint 2 spool pieces that sit outside on a marine loading arm for crude oil can you advise the best paint to use . . . .

Thank you for the enquiry, we have contacted you directly for more information.

any desmopol distributers in Ireland ??

Unfortunately we are an independant distributor and we can only ship to mainland uk at this time.

please Do you have an Australian supplier of your products, as i, require the high heat spray paint, so as i can refurbish my Aluminum b.b.q thank you ? Geoff . . .

Unfortunately we do not, we can currently only ship within the UK.

Where is the nearest store to RH118SL?

We have a trade counter in Leeds, but all products can be ordered on the website with delivery options for mainland uk addresses.

Follow us on:

Need Help?

Problem Solving