Thank you for the enqiury, please can we request some pictures of the floor and the information below are sent to [email protected] then we can assist with a specification.

Environment - interior or exterior
Substrate – concrete, power floated, porous? Timber or metal
If screed applied what is it, also provide TDS if possible
Location – garage, warehouse, domestic
Condition – bare or previously painted
Exposure – foot traffic, vehicles, forklifts, chemicals
Size of area to paint
Colour required
Finish required, matt satin or gloss
Antislip?
Application- who will be applying it>
Application timescale
Level of preparation prepared to undertake – grinding floor prior to application?

Unfortunately we cannot recommend a colour choice, but these paints can be mixed to many RAL and BS colours.

We would recommend viewing a RAL or Bs colour chart in persion to ascertain colour suitability for your application.

Assuming the UPVC is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend the Kolorbond uPVC Painting Kits.

Unfortunately we do not have a floor paint that can insulate the floor to make it feel warmer but assuming the floor is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Bradite Floor-It.

This is available in many RAL and BS colours in a semi-gloss finish.

For application to a prepared bare absorbant concrete 3 coats will be required with the first coat thinned 20% with clean water.

For 40m² you will require approximately two 5ltr tins.

Assuming the bare timber areas are not in a bilge, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Teamac Marine Undercoat followed by Teamac Marine Gloss.

This is available in many RAL and BS colours in a gloss finish.

Thank you for the enqiuiry, unfortunately the manufacturers do not produce samples.

Please see the link for Rust-Oleum Satin Furniture Paint - Shortbread it can be ordered from the website and delivered to most mainland uk addresses.

Thank you for the enqiury, we have contacted you directly.

Assuming the aluminium roof is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Eagle DoubleCoat Pro-Reflect Liquid Waterproofing.

The amount of reduction in heat will depend on the current level of weathering to aluminium roof.

If the roof is heavily weathered, the paint will make more of a difference.

For removal and treatment mould prior to redecoration we can recommend Zinsser Mould Killer & Remover.

Once this is done, the ceiling is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser Perma-White Interior.

This is an anti-mould paint suitable for high humidity areas assuming there is no direct water contact.

Increasing airflow will also reduce the likelihood of the black spots reappearing.

Assuming the powder coating is polyester, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend the Kolorbond uPVC Painting Kits for this application.

A primer would not be required.

This is available in many RAL and BS colours.

It is water based and can be applied by brush, roller or spray application.

Assuming the laminate kitchen cupboards are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Kolorbond uPVC Painting Kits.

This is available in many RAL and BS colours.

It is water based and can be applied by brush, roller or spray application.

Thank you for the enquiry, we will need more information to assist with this enquiry.

Thank you for the enquiry, we have contacted you directly for more information to assist with this enquiry.

Thank you for the enquiry, we have contacted you directly.

Unfortunately we do not recommend manually adjusting a paint's colour by mixing two of the same product together.

We have contacted you directly with more information.

Thank you for the enquiry, many of the paints we stock can be mixed to many RAL, NCS and BS colours.

We would recommend contacting the manufacturer of the EV boxes to see if their colours have RAL or BS codes, alternatively you will need to look at physical RAL or BS or NCS colour chart for a suitable match.

Assuming the meter boxes are a plastic, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum CombiColor Multi-Surface.

With plastics we would recommend testing for compatibilty and adhesion prior to full application.

We do not have resellers but we do have a trade counter in Leeds.

Thank you for the enqiury, we have contacted you directly for more information.

Assuming the worktops in question are a laminate in a kitchen, we can recommend the Rust-Oleum Worktop Transformation Kit.

These should be clean, dry, sound and prepared as detailed in the technical data sheet prior to application.

These are available in Galaxy black or Diamond White.

Assuming the timber joints are bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Mathys Elastofill for this application.

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Thank you for the enquiry, we will need to know what material the faux leading is to be able to make a recommendation.

Thank you for the enquiry, we have contacted you directly for more information.

Thank you for the enquiry, we will need more information to assist with this enquiry, please can you provide the information below to [email protected]

Environment - interior or exterior
Substrate – concrete, power floated, porous? Timber or metal
Is there a damp proof membrane present?
If screed applied what is it, also provide TDS if possible
Location – garage, warehouse, domestic
Condition – bare or previously painted
Exposure – foot traffic, vehicles, forklifts, chemicals
Size of area to paint
Colour required
Finish required, matt satin or gloss
Antislip?
Application- who will be applying it
Application timescale
Level of preparation prepared to undertake – grinding floor prior to application?

Assuming the old metal trough is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Teamac Metaclor Antifouling Primer followed by Teamac Chlorvar Chlorinated Rubber Paint.

This is available in many RAL and BS colours in a gloss finish.

This is not listed as an animal safe product, but is regularly used to paint swimming pools.

Thank you for the enquiry, we have contacted you directly to assist with this enquiry.

Assuming the handrail is previously painted, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Smartkote Safekote.

If the rail is bare steel or galvanised steel it must be primed first with Smartkote Protectakote 2K Metal Primer.

Thank you for the enqiury, unfortunately this is the smallest tin size of this paint we can supply.

Yes, assuming the block paving is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Hydron Mona-Guard Block Paving Sealer.

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Thank you for the enquiry, we will need more information to assist with this enquiry, we have contacted you directly.

Assuming the garage door previously painted metal, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum CombiColor Original.

This is available in many RAL and BS colours including RAL 7016 Anthracite.

Thank you for the enquiry, we have contacted you directly for more information.

Assuming the UPVC is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Kolorbond uPVC Painting Kits.

This is waterbased, low odour and can be mixed to many RAL and BS colours.

Unfortunately we cannot provide Farrow & Ball colours.

Many of the products we offer can be mixed to RAL, NCS & BS colours, for more information on colour matching please contact us directly - [email protected].

Assuming the external timber is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Wethertex OT25 Wood-Flex Satin Opaque Timber Paint.

Any bare timber areas should be primed prior to application with Zanders PF59 Stain Blocking Primer Finish.

Unfortunately there is no information available on if this self draining asphalt is over paintable.

We would recommend contacting the manufacturer for confirmation and if painting it would effect the draining effect.

Assuming the manufacturer agrees it can be over painted, it is clean, dry, sound, prepared as detailed in the technical data sheet and only subject to light to medium levels of foot traffic we could recommend Coo-Var Tennis Court & Drive Paint.

Thank you for the enquiry, unfortunately we do not have a product to recommend with glitter in it.

Thank you for the enquiry, we have contacted you directly for more information.

Thank you for the enquiry, unfortunately we do not have a product to recommend assuming the laminate panels are being used in working fireplace exposed to heat and or flame.

Assuming the timber is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend one coat of Teamac High Performance 2 Pack Zinc Phosphate Primer followed by 2 to 3 coats of Teamac High Performance Polyurethane Topcoat.

The surface temperature must be above 10°C during application and curing.

If the sluice gates slide up and down in runners this may wear the paint prematurely.

To avoid issues with hot tyre pick up on painted garage floors we would recommend the use of an epoxy paint such as Rust-Oleum 5300 Epoxyshield Maxx.

For this application the floor will need to be clean, dry, sound and prepared as detailed in the technical data sheet.

As the floor is previously painted we would recommend that the floor is prepared mechanically by grinding to remove the previously applied paint and prepare the surface.

Unfortunately we do not have a one coat option for this application.

If the previously applied topcoat to the grp roof was a 2 pack product, the roof is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend 1 or 2 coats of Teamac High Performance 2 Pack Zinc Phosphate Primer followed by 2 to 3 coats of Teamac High Performance Polyurethane Topcoat.

If the original topcoat applied was a single pack product we can recommend 1 to 2 coats of Teamac Marine Undercoat followed by 2 to 3 coats of Teamac Marine Gloss.

Before application of either system and loose of flaking material must be removed, the roof degreased and sanded to provide a key.

These is available in many RAL, BS and NCS colours in a gloss finish.

We have sent you an e-mail for further information.

Unfortunately we cannot recommend a suitable product for composite decking.

Unfortunately most of the manufacturers do not produce sample pots of the products, unless stated otherwise on the product pages.

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Assuming the concrete paths are subject to light foot traffic, the concrete path has a damp proof membrane present, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Acrylic Floor Paint.

This is available in many RAL, BS and NCS colours in a semi gloss finish.

If a damp proof membrane is not present this could effect the adhesion and lifespan of the paint.

Thank you for the enquiry, unfortunately we do not stock roof tiles.

Thank you for the enquiry, we will need more information to assist with this enqiury, as the area of the boat to be painted and the other products to be used in conjunction with a primer will dictate what the appropriate primer will be.

Please provide pictures of the areas to be painted and more information to [email protected]

Assuming the areas to be painted are not a roof, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 7500 Alkythane for airless application to blast prepared steelwork.

This can be mixed to many RAL, BS and NCS colours in a satin or gloss finish.

If a primer is required for steel we can recommend Rust-Oleum 569/580 QD Metal Primer.

Thank you for the enquiry, we do not have stockists in Cornwall, the Rust-Oleum Heat Resistant Paint 750°C can be ordered on the website and shipped to a mainland uk address.

Thank you for the enquiry, we have contacted you directly for more information.

Thank you for the enquiry, we have contacted you directly for more information.

Thank you for the enquiry, unfortunately we do not have a product suitable for treating a composite decking.

Any of the products we supply can be purchased on our website.

Assuming the metal is steel Rust-Oleum CombiColor Original is available mixed to Chartwell Green in a gloss or satin finish.

Yes, assuming the concrete is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Teamac Chlorvar Chlorinated rubber.

The first coat should be applied thinned 10% with Teamac Thinner 15 followed by a further two coats undiluted.

This can be mixed to many RAL, BS or NCS colours in a gloss finish.

Assuming the iron railings are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed 2 coats of Rust-Oleum CombiColor Original.

All rust must be removed prior to application.

This can be mixed to many RAL, BS or NCS colours in a gloss or satin finish.

Assuming the steel balusters are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend one coat of Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by two coats of Rust-Oleum CombiColor Original.

This can be mixed to many RAL, NCS or BS colours in a satin or gloss finish.

The millscale will need to removed prior to application, this could be done by mechanical abrasion.

Assuming the radiator is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Radiator Enamel.

Unfortunately no, this is for brush and roller application only.

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Assuming this enquiry is regarding International Interzone 101 this product must not be thinned.

No, unfortunately bitumen paint is only available in black such as Teamac Metalastic Black Bituminous this is available in 1ltr, 2.5ltr, 5ltr or 25ltr tins.

Unfortunately we do not have a product to recommend that can be added to a paint to increase adhesion, we do sell anti-slip aggregates but these must be used with a suitable paint system.

Yes, assuming the substrate is fibreglass, it is clean, dry, sound and prepared as detailed in the technical data sheet Teamac High Performance Polyurethane Topcoat could be used.

But this will not stop growth forming on the bottom of the hull like an antifoul.

Assuming the floor is concrete, you are looking to protect the laminate from damp, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend N-Virol Superseal Plus Damp Proofing DPM Paint.

Assuming the metal is steel, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum CombiColor Original for a satin finish.

This is available in 1ltr or 2.5ltr tins for mixed colours.

We have no reference for sunset orange, but this can be mixed to mant RAL, NCS or BS colours.

Unfortunately we do not have a product to recommend to paint a sealed patio.

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

Thank you for the enquiry, we will need more information regarding the project to assist with this enqiury, please send more information to [email protected]

Thank you for the enquiry, we will need more information regarding the project to assist with this enqiury, please send more information to [email protected]

Blackfriar Wood Protector Gold Star is temporarily unavailable assuming you are looking for a wood preserver we can recommend Sikagard Wood Preserver.

Assuming the polycarbonate is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum LeakSeal.

We would recommend testing for compatibility and adhesion on a small area prior to full application.

Thank you for the enquiry, unfortunately we do not have a product suitable for this application.

Assuming the timber is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Sikagard Wood Preserver.

This is also suitable to be over painted if required.

Assuming you are looking for a anti-slip floor paint, the floor boards are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Smartkote Safekote.

This comes in a range of colours or clear and is a bare foot friendly anti-slip paint with a semi-gloss finish.

Assuming the ceramic tiles are on a floor, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Smartkote Protectakote UVR Smooth.

This is available in black white or clear.

The tiles should be thoroughly cleaned and lightly sanded, then primed prior to application with Smartkote Protectakote Clear Primer Treatment

Thank you for the enquiry, we will need more information and pictures of the areas to be painted to assist with a recommendation.

Please send these to [email protected]

Assuming the engineering bricks are non porous we would recommend priming with Zinsser Bulls Eye 1-2-3.

Assuming the stove temperature does not exceed 300°C and legs on the stove have the stove more than 100mm from the concrete slab, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Stonelux Fireplace Paint for this application.

This is available in a range of colours and finishes.

Yes the Kolorbond uPVC Painting Kits can be applied by spray application.

A gravity fed spray gun is recommended with a setup and fluid tip size of 2.0 to 2.2mm.

Unfortunately the manufacturers do not produce sample pots, but assuming the substrates are upvc, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Kolorbond UPVC painting kits.

This is available in m² pack sizes and can be mixed to many RAL and BS colours.

Yes this paint should be thoroughly mixed prior to application.

Preparation and application information are in the product data sheet this can be found in the datasheets tab on the product page linked below.

Rust-Oleum CombiColor Original.

Assuming the resin fire place to be painted is more than 10cm from the heat source and not exposed to temperatures over 300°C, we can recommend Stonelux Fireplace Paint.

This is available in a range of colours and finishes.

Unfortunately the manufacturers do not provide tester pots or samples, we would recommend viewing a physical RAL, NCS or BS colour chart to choose a suitable colour.

Unfortunately no, we can only delivery to mainland uk at this time.

Unfortunately we do not have a product to recommend for application to block paving.

Assuming you are looking for a cold galvanising coating we can recommend Fosroc Galvafroid.

Preparation and application information are in the technical data sheet, these can be found in data sheets tab.

This paint can be applied directly to bare or previously painted masonry assuming it is clean, dry, sound and prepared as detailed in the technical data sheet.

For the other areas assuming they are bare timber we can recommend priming first with Zinsser Cover Stain.

Assuming the garage floor is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend the Rust-Oleum Epoxyshield Garage Floor Coating Kit.

For painting plastics, we would recommend testing for compatibility and adhesion prior to full application.

Assuming this is successful, the plastic is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum CombiColor Multi-Surface.

This is available in many RAL, NCS and BS colours in a matt, satin or gloss finish

While we do not have a specific paint for park homes, if the substrate is masonry, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Wethertex AP77 Flexible Smooth Masonry Paint.

This can be mixed to many RAL, NCS and BS colours in a matt finish.

Animal claws will be hard on any floor coating and reapplication may be required more often than for normal foot traffic.

Assuming there is a damp proof membrane present, the concrete slabs are bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Acrylic Floor Paint.

This is available in many RAL, BS or NCS colours in a semi-gloss finish

Unfortunately most of the manufacturers do not supply tester pots unless they are offered on the product pages.

Unfortunately we can only ship to mainland uk at this time.

Thank you for the enquiry, please can we ask for more information and pictures of the roof so we can assist with a recommendation.

Please send these to [email protected]

This paint can be mixed to many industry standard RAL, NCS or BS colours, colour charts for these are available to order here.

For the vertical areas of the shipping container assuming it is previously painted, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 7500 Alkythane.

This available in a satin or gloss finish, in many RAL, BS or NCS colours including RAL 6007.

If there are any areas of bare metal this should be primed first with Rust-Oleum 569/580 QD Metal Primer.

For the roof we would recommend Rust-Oleum Mathys Fillcoat, this is available in black or dark grey.

Assuming the metal area is steel, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 569/580 QD Metal Primer followed by Rust-Oleum 7500 Alkythane.

This is available in many RAL, NCS or BS colours in satin or gloss finish.

Black steel normally means this is still covered in millscale which is very brittle and full of impurities.

We would not recommend painting over this as the coatting will fail.

Jotun Jotamastic 87 in black applied at 200 to 300 microns would be recommended for blasted steel.

Before any application the roof must be clean, dry, sound and prepared as detailed in the technical data sheet a fungicidal wash such as Wethertex C10 Multi-Surface Fungicidal Wash should be used.

Assuming the previously applied coating is bitumen based, both roofs are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Eagle DoubleCoat Pro-Reflect Liquid Waterproofing.

If the coating is unknown we would recommend testing for compatibility and adhesion prior to full application.

Thank you for the enquiry, we have contacted you directly.

Most of the manufacturers unfortunately do not produce sample or tester pots, unless otherwise stated on the product pages on the website.

Assuming the upvc windows are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend the Kolorbond uPVC Painting Kits.

No primer is required, this can be mixed to many RAL, NCS or BS colours in a satin finish.

This also has a 10 year adhesion guarantee and a 5 year colour fastness guarantee.

Thank you for the enquiry, we will need more information including what the pool surround is currently painted with to assist with this enquiry, we have contacted you directly.

Thank you for the enquiry, we have contacted you directly for more information.

Assuming the galvanised garage door is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3202 Galvinoleum Primer followed by 2 coats of Rust-Oleum CombiColor Original.

This can be mixed to many RAL, NCS and BS colours in a satin or gloss finish.

Assuming the keel is has the rust removed, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Teamac Metaclor Antifouling Primer followed by 2 to 3 coats of Teamac Antifouling D Plus.

Most of the manufacturers unfortunately do not produce sample or tester pots, unless otherwise stated on the product pages on the website.

Most of the manufacturers unfortunately do not produce sample or tester pots, unless otherwise stated on the product pages on the website.

Thank you for the enquiry, we have contacted you directly.

Thank you for the enquiry, we will need information on which Zinga product this is regarding and the application, please send this to [email protected]

Unfortunately we cannot mix to automotive paint codes, we do stock Rust-Oleum Hard Hat Aerosols, such as Rust-Oleum Hard Hat Fluorescent Topcoats, Rust-Oleum 2111 Sparkling Aluminium, Rust-Oleum 2115 Aluminium, Rust-Oleum 2116 Stainless Steel Coating.

Rust-Oleum Hard Hat 2500 Transparent Protection can be applied over these.

We would recommend testing for compatibility and adhesion prior to full application on any previously painted substrates.

Unfortunately we do not have a luminous paint suitable for application to areas subject to traffic.

As an alternative you could consider the Heskins Safety-Grip Photoluminescent Anti-Slip Tape Rolls.

This product does not generate any magnetic radiation, it contains iron particles that magnets can stick to.

Rust-Oleum CombiColor Original is heat resistant up to 90°C (dry heat), so as long as the surfaces being painted didn't exceed this temperature it should be OK.

This can be mixed to many RAL, NCS and BS colours in a satin or gloss finish.

We would recommend testing for compatibility and adhesion on the previously painted lamp prior to full application.

It also must be clean, dry, sound and prepared as detailed in the technical data sheet.

This is a solvent based paint so it will have an odour untill cured and possibly for a few heat cycles.

Unfortunately we do not have a product to recommend for this application.

Thank you for the enquiry, unfortunately we do not have a product we can recommend for this application to an appliance.

Thank you for the enquiry, we have contacted you directly.

Assuming the venetian plaster is absorbant, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Keim Optil for a paint finish.

This is available in a range of colours in a matt finish.

Yes, assuming the upvc door is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend the Kolorbond UPVC painting kits for this application method.

This is available in chartwell green and many other RAL and BS colours in a satin finish.

Thank you for the enquiry, we will need to know which Bradite products have previously been used, we have contacted you directly for more information.

Assuming the issue is a water stained plasterboard ceiling, it has had time to dry out, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser B-I-N followed by Zinsser Perma-White Interior.

This can be mixed to many RAL and BS colours in a matt or satin finish.

Many of the paints we stock can be mixed to many RAL, NCS or BS colours, we would recommend viewing a physical colour chart to ascertain a suitable colour.

Masonry paint is not suitable for application to a floor, assuming the patio slabs are concrete, bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Acrylic Floor Paint.

This can be mixed to many RAL and BS colours in a semi-gloss finish.

This can also be used for the brick walls if required.

We do not have any stockists on the Isle of Wight but we can ship items ordered on the website to you.

Thank you for the enquiry, we will need more information regarding this project to assist with this enquiry.

Please send this to [email protected]

We can delivery to most UK addresses, the delivery charges can vary depending on the product, but all delivery charges are shown on the product pages on the delivery options tab.

As the stone floor has been previously sealed we would recommend checking for compatibiltiy and adhesion prior to full application.

Assuming this is sucessful, the area to be painted is subject to foot traffic, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 7200 Floorcoat PU.

This is available in many RAL, NCS and BS colours in a satin or gloss finish.

Assuming the previously painted dagger board is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Teamac Marine Undercoat followed by Teamac Marime Gloss.

This is available in many RAL, NCS and BS colours in a gloss finish.

Thank you for the enquiry, assuming the red paving bricks are a driveway, unfortunately we do not have a paint we can recommend for this application.

Assuming the areas of plaster to be painted are not exposed to temperatures over 300°C if painted white, or 180°C for tinted colour options, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Tikkurila Muuri.

This is available in a range of colours in a matt finish.

Assuming the scaffolding poles are galvanised, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Bradite One Can.

This is available in many RAL or BS colours in a matt or eggshell finish.

Please note due to the use scaffolding poles will see this may need to be regularly reapplied.

We would recommend the Kolorbond uPVC Painting Kits for this application.

Thank you for your question, we have contacted you directly for more information.

Yes, we can offer products that can be tinted ready for spray application. We would require more detail to help with a product suggestion, please call our technical helpline for further assistance one 0113 245 54 50 (option 2).

Assuming the engineered oak floor is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rubio Monocoat Oil Plus 2C.

This is available in a range of colours in a matt finish, Rubio Monocoat Oil Plus 2C Sample Set and Rubio Monocoat Oil Plus 2C Mini Colour Fan are also available to aid colour choice.

Assuming the bathroom ceiling is plaster, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser Perma-White Interior.

This is suitable for high humidity areas not subject to direct water contact.

This can be mixed to many RAL and BS colours in a matt or satin finish.

Assuming the timber is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser Cover Stain followed by 2 coats of Zinsser AllCoat Exterior (Water Based).

This can be mixed to many RAL, BS or NCS colours in a matt, satin or gloss finish.

Thank you for the enquiry, many of the paints are mixed to industry standard RAL and BS paint codes, as stated on the website we show a representation of the colours on the product pages, but these can look difference on various devices.

So we recommend to view a RAL or BS colour chart in person to ascertain colour suitability.

Assuming the canal boat hull is steel, it is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Jotun Jotamastic Smart Pack HB.

This can be used on its own below the waterline, it is available in range of colours in a semi-gloss finish.

It is recommended to apply 3 coats, the first by brush and the second and third by roller.

Minimum 1 day between coats, maximum 7 days.

If any areas to be painted are above the waterline Jotun Hardtop XP could be used as a topcoat.

Yes, ensure the surface is lightly abraded and thoroughly cleaned prior to application.

We have contacted you for more information

Thank you for the enquiry, we will need more information to assist with this enquiry, we have contacted you directly.

Thank you for the enquiry, this and many of the paints are mixed to industry standard RAL and BS paint codes, as stated on the website we show a representation of the colours on the product page, but these can look difference on various devices.

So we recommend to view a RAL or BS colour chart in person to ascertain colour suitability.

Assuming the substrate is steel, it is not subject to traffic, it is bare, clean, dry, sound and prepared as detailed technical data sheet we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by Rust-Oleum CombiColor Original.

RAL 7016 is available in 1ltr or 2.5ltr tins in a satin or gloss finish.

Thank you for the enquiry, unfortunately we do not have a product we can recommend for this application to an appliance.

If you wish to remove the previously applied paint this can be done by sanding or using a paint stripper such as Rust-Oleum Nr.1 Green Paint Stripper.

Assuming the galvanised steel railings are now bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3202 Galvinoleum Primer followed by two coats of Rust-Oleum 7500 Alkythane

This can be mixed to many RAL, NCS or BS colours in a satin or gloss finish.

We do not have a paint that can achieve a natural stone look for this application, but if a painted semi-gloss finish is acceptable, the concrete paving slabs are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Acrylic Floor Paint.

This can be mixed to many RAL, NCS or BS colours in a semi-gloss finish.

We would recommend the Rust-Oleum Combicolor Original in RAL7016 - Anthracite Grey.

Thank you for the enquiry, please can you send more information and pictures of the fibreglass item you wish to paint to [email protected] then we can assist with a recommendation.

Thank you for the enquiry, we have contacted you directly with more information.

Thank you for the enquiry, we will need more information to assist with this enquiry, please send the information below to [email protected] along with pictures of the area.

Environment - interior or exterior
Substrate – concrete, power floated, porous? Timber or metal
If screed applied what is it, also provide TDS if possible
Location – garage, warehouse, domestic
Condition – bare or previously painted
Exposure – foot traffic, vehicles, forklifts, chemicals
Size of area to paint
Colour required
Finish required, matt satin or gloss
Antislip?
Application- who will be applying it>
Application timescale
Level of preparation prepared to undertake – grinding floor prior to application?

Assuming the bare shipping container is steel, it is clean, dry, sound and prepared as detailed in the techncial data sheet we can recommend Rust-Oleum 7500 Alkythane for the sides and Rust-Oleum Mathys Fillcoat for the roof.

Rust-Oleum 7500 Alkythane can be mixed to many RAL, NCS or BS colours in a satin or gloss finish. 

Rust-Oleum Mathys Fillcoat is only available in Dark Grey or Black.

Any bare metal areas should be primed first with Rust-Oleum 569/580 QD Metal Primer.

Assuming the external concrete steps are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-var Anti-Slip Acrylic Floor Paint.

This is available in many RAL, NCS or BS colours in a matt finish.

Assuming the red brick paving edging is clean,dry, sound and prepared as detailed in the technical data sheet we can recommend Hydron Mona-Guard Revive.

This is available in black or red.

Hydron have a range of mural paints available here.

If a clear protective finish is required also Hydron Nu-Guard AG can also be used over these products.

Thank you for the enquiry, unfortunately we do not have a product to recommend suitable for direct water contact.

Thank you for the enquiry, please can you provide more information regarding what you are looking to protect the bench from and pictures of the bench to [email protected]

Assuming fire protection is required we have e-mailed you for more information.

Unfortunately we do not have a product that is suitable to be painted on the treads that would be luminous. You could consider a tape option such as the below:

Heskins Photoluminescent Egress Tape

Providing the fireplace is a minimum of 10cm away from any heat source and will not exceed 300°C you could consider lightly abrading the substrate and then priming it using the Stonelux Primer & Undercoat

Followed by the Stonelux Fireplace Paint

Please see our how to guide on Painting the Walls around a Fireplace or Multi Fuel Stove

Yes, certification is available for many of the fire protection products we offer. Certification can be applied for upon completion of the project, this is not supplied with the product.

Please see our how to guide on Painting the Walls around a Fireplace or Multi Fuel Stove

Delivery charges can vary depending on the product and manufacturer.

You can find delivery options and charges on every product page in the delivery options tab.

Thank you for the enquiry, please can you provide pictures of this area and information on what the panels are made of to [email protected].

Thank you for the enqiury, please can you provide more information to [email protected]

The Blackfriar Professional Water Based Floor Sealer is available via the link below:

Blackfriar Professional Water Based Floor Sealer

Rust should always be prepared prior to painting but something like Rust-Oleum CombiColor Original would allow you to not need to use a separate primer. You could simply prepare the metal by cleaning, and removing all loose and flaking existing coatings, rust, etc. and then apply 2-3 coats of Rust-Oleum CombiColor Original in the colour and finish of your choice.

We have a blog post you can refer to called How To Paint Patio Slabs & Block Paving which will hopefully guide you through the process to choosing the right paint for your project. Should you still need any further information or help, please contact our Technical Team on 0113 2455450 option 2.

Assuming the inside of the fibreglass dinghy is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Teamac Marine Undercoat, followed by Teamac Marine Gloss.

This can be mixed to many RAL, NCS and BS colours in a gloss finish.

Assuming the fibreglass roof is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Teamac High Performance Polyurethane Topcoat.

This can be mixed to many RAL, NCS and BS colours in a gloss finish.

But unfortunately not to an automotive paint code, we would recommend viewing a physical colour chart to choose a suitable colour.

These are the references for the bases the colours are mixed on and are priced from.

When select your chosen RAL, NCS or BS colours these are automatically selected for you.

Thank you for the enqiury, please can you provide more information on what you are looking to paint to [email protected]

Thank you for the enquiry, please can you provide more information and pictures of the hull to [email protected]

Unfortunately the manufacturer does not produce tester pots, we would recommend viewing a physical RAL colour chart to ascertain a suitable colour.

If you are local to Leeds we have these on our trade counter to view or you maybe apply to see these at other local trade paint suppliers.

Rust-Oleum Nr.1 Green Paint Stripper can be used to remove oil, alkyd, emulsions, varnishes and most two component materials from substrates such as metal.

Preparation and application information are in the technical data sheet, this can be found in the data sheets tab on the product page.

Rust-Oleum Chalky Garden Furniture Paint Aerosol in Anthracite would be the closest thing we have to what you have asked for.

Hydron Nu-Guard AG would be our recommendation for this, we have no information in regards to child/toy safety of the coating but in terms of a product that can be applied to timber to allow easy removal of any subsequent graffiti attacks it fits the bill.

The main difference is the Rust-Oleum Furniture Paint is available in a number of different sheen levels whereas Rust-Oleum Kitchen Cupboard Paint is only available in a matt finish. You can download the product data sheets for more information from each product page linked to above under the 'DATA SHEETS' tab. Colour samples can be ordered from https://rustoleumcolours.co.uk/

Thank you for the enquiry, unfortunately we do not have a product to recommend for this enquiry.

These come in a pack of 5.

No, unfortunately we do not supply timber.

Assuming the metal cladding and shutters are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Mathys Noxyde Peganox.

This is waterbased, suitable for brush, roller or spray application and is available in a range of colours in a Satin Gloss finish.

The Rust-Oleum Chalky Floor Paint is not recommended for areas exposed to direct water contact.

Unfortunately we cannot recommend this product and over painting with a lacquer.

Assuming the bathroom floor is concrete, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Smartkote Safekote.

This is a bare foot friendly antislip paint available in clear or a range of colours in a semi gloss finish.

Increasing air flow will aid this issue, assuming the area, is clean, dry, sound and prepared as detailed in the technical data sheet using a product such as N-Virol Suretherm Goodbye Mould Cleaning Spray we can recommend N-Virol Suretherm Goodbye Mould Thermal Anti Condensation Paint.

This can be over painted or papered.

Assuming you are looking for an aerosol spray paint, the galvanised steel is clean, dry, sound and prepard as detailed in the technical data sheet unfortunately no, the area would need to be primed first.

If the area is not exposed to traffic or heat we can recommend Maston Spraypaint 2K Primer followed by Maston Spraypaint 2K Colours.

This can be mixed to many RAL , NCS colours in a matt, semi-gloss or high gloss finish.

Thank you for the enqiury, we have contacted directly fo more information to assist with this enquiry.

Unfortunately these products are not available in the UK.

Unfortunately we do not have a product to recommend for this application.

Teamac Metalcote Plant Enamel is available mixed to 1795 Kubota orange.

Assuming the red tiles are ceramic, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser Bulls Eye 1-2-3 followed by 3 coats of Zinsser Allcoat Exterior (Water based).

This is available in many RAL, NCS or BS colours in a matt, satin or gloss finish.

We would recommend viewing a physical colour chart to choose a suitable match.

Thank you for the enquiry, assuming this is regarding Rust-Oleum Universal All Surface Paint - Brush Grade unforutnately no this is for brush or roller application only.

It is available in an aerosol form also, Rust-Oleum Universal All Surface Paint Aerosol.

Assuming the upvc is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Kolorbond uPVC Painting Kits.

This can be mixed to many RAL, BS or NCS colours in a satin finish.

There is no reference for a medium oak colour, we would recommend viewing a physical colour chart to find a suitable match for your application.

This is not a marine paint but assuming the area to be painted is above the waterline, not subject to traffic, Rust-Oleum CombiColor Original could be used.

We would recommend a test for compatibility and adhesion is undertaken on a small area prior to full application.

The substrate should be clean, dry, sound and prepared as detailed in the technical data sheet.

As an alternative requiring the same testing and preparation we can recomend Teamac Marine Undercoat followed by Teamac Marine Gloss.

This can be mixed to many RAL, NCS or BS colours in a gloss finish.

You can purchase the paint or the preparation materials seperately, please see the link here to all Technispray products.

Please note the preparatory cleaners must be used or the manufacturer guarantees for adhesion and colour fastness would not be honoured.

Thank you for the enquiry, unfortunately we do not stock jewellers cement.

We would recommend consulting your local building control department.

We can only ship to mainland UK at this time.

Assuming the galvanised storage tank is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend the barrel is first prepared with Teamac Mordant Solution (T Wash), Teamac Metaclor Antifouling Primer is applied followed by 2 coats of Teamac Chlorvar Chlorinated Rubber Paint for this application.

This is available in many RAL, NCS or BS colours in a gloss finish.

Once cured it will not be harmful to fish.

We do not stock Sandtex, assuming the plywood is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Wethertex HBS Flex-Coat Hi-Build Coating.

On plywood we recommend priming first with Wethertex ST1 Quick Dry Stabilising Primer and then using a plasterers scrim on the joints before applying the Wethertex HBS Flex-Coat Hi-Build Coating.

The smallest tin size is 15kg.

Assuming the teak faced ply is clean, dry, sound and prepared as detailed in the technical data sheet, we can recommend Teamac Aluminium Wood Primer followed by Teamac Marine Undercoat and Teamac Marine Gloss.

If a lower gloss level is required Teamac Marine Matting Agent can be used with the gloss.

This can be mixed to many RAL, NCS or BS colours. 

Assuming the previously painted timber is clean, dry, sound and prepared as detailed in the tehnical data sheet we can recommend Zinsser Cover Stain is applied to any bare timber areas then two coats of Zinsser AllCoat Exterior (Water Based), or three coats to any areas subject to pooling water.

This can be mixed to many RAL, NCS or BS colours in a matt, satin or gloss finish.

Thank you for the enquiry, we have contacted you directly.

Unfortunately we do not have a product to recommend for this application.

Unfortunately unless the imprinted concrete drive way that has been sealed can be fully abraded or grinded prior to application we do not have product to recommend for this application.

Assuming the newly applied render is sand and cement based, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Wethertex ST1 Quick Dry Stabilising Primer followed by Wethertex AP77 Flexible Smooth Masonry Paint.

This can be mixed in many RAL, NCS or BS colours in a matt finish.

Thank you for the enquiry, unfortunately we do not have a product to recommend for this application.

This product has been rebranded as RSL Resuflor HB.

This product does not have a level of slip resistance on its own, but with the addition of RSL Resuflor HB Profile Aggregate a level of slip resistance can be achieved.

Unfortunately most of the manufacturers do not offer or sell colour samples or swatches as most of the products are mixed to industry standard colours such as RAL, NCS or BS.

We do sell these charts here.

Thank you for the enquiry, please can you provide more information on what it to be painted to match the colour of felt to [email protected] and we can look for a suitable product.

Unfortunately we do not stock gas fires.

Unfortunately we do not have a product to recommend for this application.

Thank you for the enquiry, unfortunately we do not have a paint in yellow suitable for this application.

Assuming the rubber tyres are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Technispray Hypakolor.

This is available in aerosols or 1ltr, 5ltr or 20ltr tins and can be mixed to many RAL, NCS or BS colours in a Satin finish.

We would recommend testing for compatibility and adhesion prior to full application.

Unfortunately this is currently unavailable but will be live to order on the website as soon as that changes.

Assuming the external concrete area has a damp proof membrane, it is not subject to vehicle traffic, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Acrylic Floor Paint.

This is available in many RAL, NCS or BS colours in a semi-gloss finish.

Assuming the concrete blocks are bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Hydron Nu-Guard AG.

This is available in clear or a range of colours in a semi-matt finish.

If the concerte blocks are porous, Hydron Nu-Guard WB Concrete Sealer should be used prior to application.

We stock many paints that are available in 1ltr tin sizes.

Assuming the chair is bare timber, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser Cover Stain followed by Zinsser Allcoat Exterior (Water based).

This is available in many RAL, NCS or BS colours in a matt, satin, or gloss finish.

Thank you for the enquiry, please can you provide more information on what the formica object to be painted is and also if the primer must be compatibility with another product to [email protected].

Thank you for the enquiry, we have contacted you directly for more information.

Unfortunately this is not a product we can supply.

Assuming the lime rendered walls are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Keim Royalan.

This is available in a range of colours in a matt finish.

We do not have a product which will guarantee no maintenance is required for decades.

But assuming the timber is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zanders PF59 Stain Blocking Primer Finish followed by Wethertex OT25 Wood-Flex Satin Opaque Timber Paint.

This is available in many RAL, NCS or BS colours in a matt finish.

This can provide upto 12 years of protection.

Assuming the cut and rusted areas are clean ,dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by Rust-Oleum CombiColor Original.

All rust must be removed prior to application, we would recommend testing for compatibility and adhesion prior to overpainting with any other topcoat.

Assuming there is a damp proof membrane present below the slabs, they are not subject to vehicle traffic, they are bare, clean, dry, sound and prepared as detailed in the technical data sheet, we can recommend Coo-var Anti-Slip Acrylic Floor Paint.

This is available in a range BS, RAL or NCS colours in a matt finish.

Unfortunately without the correct preparation we do not have a product we can recommend.

Assuming the timber cladding is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Tikkurila Pinja Color Plus.

This is available in a range of colours in a semi-matt finish.

We would recommend you test for compatibility and adhesion on a small area prior to full application.

Unfortunately if the tank is not water tight we do not have a product to recommend to line it with.

NSF/ANSI Standard 61 pertains to products in contact with potable or drinking water in the United States. 

This is not a colour code for a grey.

Assuming the composite door is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Kolorbond uPVC Painting Kits.

This available in many RAL, NCS or BS colours in a satin finish.

This has an adhesion guarantee of 10 years and a colour fastness guarantee of 5 years.

Unfortunately we do not have a topcoat to recommend, we have contacted you directly for more information.

Unfortunately this product is not suitable for use in a bathroom if it is regular water contact and we do not have a product to recommend to over paint this.

Assuming the floor is made of a compatible substrate, it is clean, dry, sound and prepared as detailed in the technical data sheet you could consider Smartkote Safekote.

This is available in a range of colours or clear in a semi-gloss finish.

Assuming the render is sand and cement based, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Wethertex HD77 Pliolite Heavy Textured Wall Coating.

This is available in a range of colours.

Unfortunately no, we do not have a product to recommend for application to a laminate finish to achieve a level of fire protection.

Unfortunately we do not have a product to recommend that is tested to be animal safe.

Thank you for the enquiry, unfortunately we do not have a product we can recommend for this application.

Unfortunately we do not have a product we can recommend for this application.

Thank you for the enquiry, please can you provide more information and pictures of the areas in question to [email protected] so we can look into this for you.

Assuming the aluminium is clean,dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3202 Galvinoleum Primer followed by Rust-Oleum CombiColor Original.

This can be mixed to many RAL, NCS or BS colours in a satin or gloss finish.

Assuming the tiles are concrete, not terracotta, the are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Cromar Renocoat Roof Tile Renovation Paint.

This is available in slate grey or dark brown.

There can be variance in colours of bricks, if the paint states the colour as a brick red it will be a red, but we would recommend testing on small area prior to application to ascertain if the colour is suitable for your application.

Assuming there is a damp proof membrane present, the patio slabs are concrete, they are bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Acrylic Floor Paint.

This can be mixed to many RAL, NCS or BS colours in a semi-gloss finish.

Thank you for the enquiry, we have contacted you directly for more information.

Thank you for the enquiry, we will need more information of which product you require to assist with this enquiry, please send this to [email protected]

Or a picture of the tin you need a hardener for.

Thank you for the enquiry, please can you provide more information and pictures of the areas in question to [email protected] so we can look into this for you.

Unfortunately we do not have a product we can recommend for this application.

Assuming you are looking for a secondary barrier beneath the render system, we would suggest Sikalastic 1K.

This can be used on all ICF type constructions.

Assuming the paving slabs are concrete, there is a damp proof membrane present, they are clean, dry, sound and prepared as detailed in the technical data sheet, we can recommend Coo-Var Acrylic Floor Paint.

This is available in many RAL, NCS or BS colours in a semi-gloss finish.

Assuming the kitchen worktop is a laminate, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Worktop Transformation Kit.

This is available in Galaxy black or Diamond white but unfortunately we do not have an aerosol option.

Assuming the stone is bare, it is porous, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser Allcoat Exterior (Water based).

This can be mixed to many RAL, NCS or BS colours in a matt, satin or gloss finish.

Unfortunately we cannot mix to, or cross reference automotive paint codes.

We would recommend viewing a physical RAL, NCS or BS colour chart to ascertain suitability of a colour.

Please can you provide more information on the product in question to [email protected]

The coverage rate for the this product is 11m² per litre per coat.

We would suggest a medium pile solvent resistant Roller Sleeve.

Thank you for the enquiry, we do not have a product with the reference MP90, please can you provide more information on the project to [email protected] so we can assist with an alternative.

Thank you for the enquiry, unfortunately we do not have a paint suitable for external application with a stone effect finish for use on a patio.

But for the wall covings, assuming they are stone, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Stonelux Windowsill Paint.

This is available in a range of coluors and finishes.

Assuming the gas/electric kiosks are made of a suitable substrate, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Hydron Nu-Guard AG.

This is available in clear and a range of colours including a green in satin finish.

Assuming the fireplace is never to be used, the stone is porous, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Acrylic Floor Paint.

This is available many RAL, NCS or BS colours in a semi gloss finish.

If the fire place is ever to be used we would recommend Stonelux Fireplace Paint.

Assuming the concrete floor has a damp proof membrane, it is only subject to foot traffic, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 7200 Floorcoat PU.

This is available in many RAL, NCS or BS colours in a gloss or satin finish.

Assuming the vinyl floor is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Smartkote Protectakote UVR Smooth.

The area to be painted must be lightly sanded and solvent wiped prior to application.

This paint is available in black, white or clear in a gloss finish.

The coverage rate is 4 to 8m² per litre depending on the porosity of the surface per coat.

One coat is generally sufficient but a second may be required.

Unfortunately we do not have a suitable product to recommend for this application.

Unfortunately we cannot offer Colour Sample Sachets of a manufacturers own colour, only RAL, NCS or BS colours.

Assuming there is a damp proof membrane present below the concrete paving, the paving is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Acrylic Floor Paint.

This is available in many RAL, NCS or BS colours in a semi gloss finish.

Assuming the product you purchased on clearance is Wethertex HBS Flex-Coat Hi-Build Coating, please use this link to the main product listing.

The coverage rate for this product is provided in kg/m² @ 2-3kg/m²

We can mix many paints to RAL, NCS or BS colours, we would recommend viewing a physical colour chart to ascertain a suitable match to a mahogany you are looking for.

Then if you can provide information regarding what you are painting to [email protected] we can assist with a recommendation.

Assuming the patio slabs are concrete, there is a damp proof membrane present, the area is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Acrylic Floor Paint.

This can be mixed in many RAL, NCS or BS colours in a semi gloss finish.

We would recommend viewing a physical colour chart in person to asertain a suitable colour for your requirements.

Assuming the brickwork is bare other than the graffiti we can recommend Hydron AG4 Graffiti Remover for this application.

Hydron SL1 Shadow Lifter may be required if the graffiti has become ingrained.  

Thank you for the enquiry, we will need more information on what type of stone the coping is made of and how it can be prepared.

Please can you provide this information with pictures of the area to [email protected]

Colour Sample Sachets are available mixed to many RAL, NCS or BS colours in a satin finish.

Yes please see the link to the Colour Match Service.

Assuming the upvc is clean, dry, sound and prepared as detailed in technical data sheet we can recommend the Kolorbond uPVC Painting Kits

This has guarantees for colour fastness and adhesion.

This is available in many RAL, NCS or BS colours in a satin finish.

If you have some of the Rust-Oleum 7200 Floorcoat PU left over, the painted area is clean, dry, sound and prepared as detailed in the technical data sheet you could apply another coat including Rust-Oleum Non-Skid Additive NS 100.

Please note if the previously applied paint is fully cured this must be abraded prior to application.

Unfortunately we do not have a chalky finish floor paint suitable for application to a tiled floor.

For application to wall tiles in a bathroom, assuming they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Tile Transformation Kit.

This is available in Aspen White.

Assuming the timber is not subject to traffic, it is bare, clean, dry, sound and prepared as detailed in the technical data sheet, we can recommend Zinsser Cover Stain followed by Zinsser AllCoat Exterior (Water Based).

This is available in many RAL, NCS or BS colours in a matt, satin or gloss finish.

Unfortunately we do not have a paint to recommend for this application.

Unfortunately we do not have a clear varnish for this application to external porcelain tiles.

Assuming you are enquiring about thermoplastic lines such as Ennis-Flint Flexiline Thermoplastic Lines these should not be applied over existing paint or taped markings.

There is not a difference in the paint, some popular colours are available ready mixed while many RAL, NCS or BS colours can be mixed. 

Assuming the concrete has a damp proof membrane present, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-var Acrylic Floor Paint.

This is available in many RAL, NCS or BS colours in a semi gloss finish.

If an anti-slip finish is required you can consider Coo-Var Antislip Acrylic Floor Paint.

Unfortunately no, this can only be used on plaster, brick or concrete.

For this application assuming the wooden furniture is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Furniture Paint.

Assuming the block paving is porous, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Tikkurila Patio Paving Stain.

Unfortunately this is temporarily unavailable.

Assuming the lime render is clean, dry, sound and prepared as detailed in the technical data sheet, we can recommend Keim Royalan for this application.

Onto unpainted surfaces Keim Royalan should be applied as a two-coat system, the first coat to be diluted with 20% by weight Keim Royalan Dilution and applied by brush or roller, working well into all surfaces, with a minimum period of 12 hours between coats.

For previously painted surfaces Keim Royalan Grob should be used as a first coat.

It is available in a range of colours, Keim Colour Samples are available.

Assuming the softwood gates are clean, dry, sound and prepared as detailed in the the technical data sheet we can recommend Teamac Penetrating Wood Primer White followed by Teamac Marine Gloss.

This can be mixed to RAL, NCS or BS colours in a gloss finish.

Please can you provide more information of what is to be painted so we can assist with a recommendation to [email protected]

Unfortunately we do not have a product to recommend for this application.

Assuming the slate is clean,dry, sound and prepared as detailed in the technical data sheet we can recommend Hydron Mona-Guard Nhance.

This provides oil and water repellent properties and lifts the true colour of the substrate.

Assuming the table is steel, is it clean, dry, sound and prepared as detailed in the technical data sheet with the rust removed we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by Rust-Oleum CombiColor Original.

This is available in RAL 9023 and many other RAL, NCS or BS colours in a satin or gloss finish.

Unfortunately we do not have a product to recommend to seal a butyl pond liner.

Unfortunately we do not have a product to cover stains, we would recommend if the previously applied coating is sound it is cleaned with a product such as Rust-Oleum Mathys ND14 Cleaner Degreaser.

To recommend a suitable product to overpaint this area will will need more information, please send the information below to [email protected]

Environment - interior or exterior
Substrate – concrete, power floated, porous? Timber or metal
If screed applied what is it, also provide TDS if possible
Location – garage, warehouse, domestic
Condition – bare or previously painted
Exposure – foot traffic, vehicles, forklifts, chemicals
Size of area to paint
Colour required
Finish required, matt satin or gloss
Antislip?
Application- who will be applying it>
Application timescale
Level of preparation prepared to undertake – grinding floor prior to application?

Unfortunately we currently do not ship to Northern Ireland.

Assuming you are looking to paint the inside of glass windows to reduce light and heat you could consider Coo-Var White Glass Shading

Please can you provide more information on what the galvanised object to be painted is to [email protected] so we can assist with a recommendation.

Thank you for the enquiry, we have contacted you directly by email.

Assuming the previously painted aluminium furniture has all the loose and flaking material removed, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Bradite One Can Matt.

This can be mixed to many RAL, NCS or BS colours.

Assuming you are looking looking for a masonry paint, you could consider Rust-Oleum Mathys Murfill Waterproofing Coating, this is available in many RAL, NCS or BS colours and states it is 400% elastic.

If you are looking for an elastomeric floor paint you could consider Flag Heavy Duty Elastomeric Floor Coating (Anti-Slip), this is available in a range of colours including 2 grey options.

Unfortunately if the part A and B were not mixed correctly prior to application it will not cure.

This will have to be removed manually by means of scrapping and rags in conjunction with the use of 109 Tool Cleaner prior to preparing the substrate for another application. .

Assuming the fibreglass is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can reocmmend Teamac High Performance Polyurethane Topcoat.

This is available in many RAL, NCS or BS colours in a gloss finish.

Unfortunately the manufacturers do not currently supply samples, but these paints can be mixed to many RL, NCS or BS colours.

We would recommend viewing a physical colour chart in person to ascertain colour suitability.

Please can you provide more information to [email protected]

We do stock Hempel Epoxy Filler 35250 Light Grey

All pricing can be found on the link above.

You could consider the Kolorbond uPVC Painting Kits.

This is available mixed to many RAL, NCS or BS colours in a satin finish. 

The manufacturer offers a 10 year adhesion guarantee and 5 years on colour fastness.

Unfortunately no this would not be suitable.

Assuming the worktop is bare timber, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 4900 Polycoat 2K.

This can resist boiling water, alcohol, coffee, red wine, dilute acid and alkalis.

Assuming the previously painted metal containers are steel, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Mathys Noxyde Peganoxfor the vertical areas.

This is available in a range of colours including RAL 6011 but in a satin gloss finish.

For the roof areas as they will be subject to pooling water we would recommend Rust-Oleum Mathys Fillcoat.

Assuming the chiminea is clean, dry, sound and prepared as detailed in the technical data sheet, it is not subject to temperatures over 600°C we can recommend Blackfriar High-Heat Resistant Paint.

Assuming the stone wall is bare and porous, it is clean, dry, sound and prepared as detailed in the techncial data sheet we can recommend Zinsser AllCoat Exterior (Water Based).

This can be airless sprayed and is available in many RAL, NCS or BS colours in a matt, satin or gloss finish.

Assuming the composite window sill is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend the Kolorbond uPVC Painting Kits.

This is available in many RAL, NCS or BS colours in a satin finish.

Unfortunately we do not have contractors.

Please see the link to our Colour Match Service for the form.

Unfortunately we do not have a product we can recommend for this application.

Assuming the previously painted walk way is steel, all rust is removed, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Smartkote Protectakote UVR.

Any bare metal areas should be primed first with Smartkote Protectakote 2K Metal Primer.

We would recommend testing for compatibility and adhesion on any previously applied coatings prior to full application.

This is available in a range of colours and a clear option.

Assuming you are looking to paint a laminate worktop, it is clean ,dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Worktop Transformation Kit.

This is Heat resistant up to 135°C for short periods of time, but hot cookware should not be placed on to the worktop.

This is available in galaxy black and diamond white.

Assuming you’re painting exterior cement based masonry, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Wethertex HBS Flex-Coat Hi-Build Coating.

This is available in a standard range of colours, RAL, NCS and BS colours in a matt finish.

As this is a difficult substrate to gain a key to, a good clean and degrease would be recommended using hot soapy water, rinsing with warm water then wiping over with Methylated Spirit.

Once this is done, the marble is clean, dry and sound we would recommend Zinsser Bulls Eye 1-2-3 followed by 2 coats of Zinsser AllCoat Exterior (Water Based).

This is available in many RAL, NCS or BS colours in a matt, satin or gloss finish.

Assuming the timber is bare, it is clean ,dry, sound and prepared as detailed in the technical data sheet we can recommend Stonelux Fireplace Paint.

This is available in a range of colours and finishes.

Surfaces painted with Stonelux Fireplace Paint must be a minimum of 100mm (10cm) away from any heat source.

Stonelux Primer & Undercoat should be applied prior to application.

Unfortunately we do not have a product we can recommend for this application.

Colour Sample Sachets are available mixed to many RAL, NCS or BS colours.

These can be ordered on link above.

We can offer Colour Sample Sachets mixed to many RAL, NCS or BS colours. 

Thank you for the enquiry, we will need more information and pictures of the balcony to assist with this enquiry.

Please can you send this information to [email protected] 

We have many paints capable of being mixed to RAL 7033 but we will need more information on this wire to be painted.

Please can you send this to [email protected]

Assuming the old coating of Zinga is clean ,dry, sound and prepared as detailed in the technical data sheet we would recommend reapplying Zinga.

The area should be steam-cleaned to remove all contamination from porous surfaces, dried,  then blast cleaned prior to application.

Assuming the tarmac is only subject to foot traffic, it is clean, dry, sound and prepared as detailed in the technical data sheet, we can recommend Blackfriar Professional Acrylic Floor Paint.

This is available in many RAL, NCS or BS colours in a semi gloss finish.

Assuming the previously painted metal garage door is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum CombiColor Original.

This is available in many RAL, NCS or BS colours and Chartwell Green in a gloss or satin finish.

Rust-Oleum CombiColor Original can be mixed to many RAL, NCS or BS colours including many yellows. 

Pricing for these can be found on the product page.

Yes these can be applied to existing, dry, sound coatings, we do not recommend applying these paints to wet or damp surfaces.

We don't offer a black intumescent paint unfortunately, we have contacted you directly for more information.

Thank you for the enquiry, these data sheets can be found in the data sheets tab on the product page linked below.

Axalta Speedspray QDH Primer

Assuming the laminate is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Worktop Transformation Kit.

This is available in galaxy black or diamond white.

Thank you for the enquiry, please can you provide more information and pictures of this project to [email protected] and we can assist you further.

Thank you for the enquiry, unfortunately we do not have a stain blocking paint suitable for application to a fire surround.

Thank you for the enquiry, please can you provide more information and pictures of the issue to [email protected] and we can look into this for you.

While the external concrete floor assuming it is clean, dry, sound, has a damp proof membrane present and is prepared as detailed in the technical data sheet could be painted, gloss paint is not suitable to be walked on.

It has been applied to an unprepared surface.

We would recommend the paint is either sanded off prior to a suitable floor paint is applied such as Coo-Var Acrylic Floor Paint or try to remove it with Rust-Oleum Nr.1 Green Paint Stripper.

We would not recommend this product for application to a table.

Yes Ardenbrite Protective Glaze is a clear product for application over Ardenbrite Metallic Paint.

Assuming these steels are not previously painted with an intumescent paint system, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum CombiColor Original.

This can be mixed in many RAL, NCS or BS colours in a satin or gloss finish.

We would recommend testing for compatbility and adhesion on previously painted areas.

Assuming the aluminium is clean, dry, sound and prepared as detailed in the technical data sheet, we can recommend Bradite One Can Matt.

We would recommend 2 coats, this can be mixed to many RAL, NCS or BS colours.

Assuming the polycarbonate substrate is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser AllCoat Exterior (Water Based).

We would recommend testing for compatibility and adhesion prior to full application on a small area.

This can be mixed to many RAL, NCS or BS colours in a matt, satin or gloss finish.

Thank you for the enquiry, unfortunately we do not have a paint we can recommend to match the original brickwork that could be applied below a damp proof course.

Thank you for the enquiry, unfortunately we do not have a product to recommend for painting bricked paving.

Unfortunately we do not have a product we can recommend for this application.

Unfortunately Tikkurila Patio Paving Stain is not suitable for application to natural stone.

Unfortunately we do not have a product we can recommend for this application.

Assuming the steels do not require a level of fire protection, all rust is removed, they are bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum CombiColor Original.

This is available in many RAL, NCS or BS colours in a satin or gloss finish.

A suitable primer such as Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion should be used prior to application.

We mix many of the paints we stock to industry standard RAL, NCS or BS colours, as such the manufacturers do not produce colour charts unless stated otherwise on the product pages.

The industry standard charts can be purchased here or are available for viewing in person at our trade counter in Leeds.

Unfortunately we cannot recommend a colour match, but we mix many of the paints we stock to industry standard RAL, NCS or BS colours.

We would recommend viewing a physical colour chart to choose a suitable match.

Assuming by spray paint you mean and aerosol, we would not recommend an aerosol for this application as the film build will be thin.

For a longer life option application by brush roller or airless spray would be prefered.

Assuming the cast iron pipe is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by two coats of Rust-Oleum CombiColor Original.

This is available in many RAL, NCS or BS colours in a satin or gloss finish.

Kolorbond Original is available in aerosol form and can be mixed to many RAL, NCS or BS colours in a range of finishes.

Thank you for the enquiry, please can you provide more information regarding the application and the product to [email protected].

Unfortunately we do not stock tile adhesives. 

We would recommend to consult the technical data sheet of the tile adhesive to be used to ascertain a suitable compatible primer.

Thank you for the enquiry, please can you provide more information to [email protected] so we can assist.

Thank you for the enquiry, please can you provide more information and pictures of what is to be painted and its location to [email protected], then we can assist with a recommendation.

Assuming the 20ft grp boat is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Teamac Metaclor Antifouling Primer followed by Teamac Antifouling D Plus.

Please note this is for professional use only.

Assuming the synthetic pitch is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Grassline Syn-Tech Synthetic Line Marking Paint.

This is available in a range of colours.

Unfortunately we do not have a granite effect floor paint, the only textured floor paints we stock are antislip.

Assuming the concrete slab has a damp proof membrane present, it is only subject to foot traffic, the concrete is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-var antislip acrylic floor paint.

This can be mixed to many RAL, NCs or BS colours in a matt finish.

Unfortunately we do not have a paint to recommend to smooth out lumps and bumps, they will only mirror the undulations of the substrate.

We would recommend to consult the technical data sheet for the particular polyurethane paint you wish to apply to ascertain if a primer is required and what the manufacturers approved primer is.

Unfortunately we do not stock this product but we can supply other Barrettine Paint Removal Products. 

Unfortunately hammerite is not a brand of paint we currently stock. 

We do not have a product we can recommend that is tested as being safe with animals.

Assuming a semi gloss finish is acceptable, the heater is metal, it is clean, dry, sound and prepared as detailed in the technical data sheet this Coo-Var Radiator Enamel can be used.

After each application allow to dry for one hour, then stove with the radiator at full heat (70 deg C) for one hour to ensure drying.

Unfortunately we do not have a product to recommend for this application.

Thank you for the enqury, we will need more information on the materials the stack is made of and what preparation can be undertaken to assist with this enquiry.

Please can you send this and any other information to [email protected].

Pictures of the area to be painted would also be helpful.

Assuming the bare sand and cement render is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend two coats of AP77 with the first coat diluted 10 to 50% with clean water. depending on the substrate.

This can be mixed to many RAL, NCS or BS colours in a matt finish.

Unfortunately the manufacturers do not produce colour charts but they are available to purchase here or to view at our trade counter in Leeds or many other trade paint suppliers.

Assuming the concrete floor has a damp proof membrane, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Speed Screed.

This is suitable for vehicle traffic, including forklifts.

Unfortunately we do not have a product we can recommend that is tested to be animal safe.

Unfortunately we do not have a product we can recommend for this application.

 Unfortunately we do not have a product we can recommend for this application.

Assuming the fibreglass roof is clean, dry, sound and prepared as detailed in the technical data sheet, we can recommend Britannia Aquashield Eco.

This is available in black, grey or solar reflective white.

Please note this should not be used on areas subject to regular foot traffic.

Assuming the corrugated roof has all the rust removed, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend 2 coats at 200grams per m² of Rust-Oleum Mathys Noxyde Peganox.

This can be applied by brush or roller in a range of colours.

Assuming the upvc door is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend the Kolorbond uPVC Painting Kits.

This is available in many RAL, NCS or BS colours in a satin finish.

Thank you for the enquiry, we will need more information on the doors, internal, external, are they bare, oiled or painted to assist with this enquiry.

Please send this to [email protected].

Alternatively if you have already found a suitable product, on every product page you will see a data sheets tab, within that tab will be a product data sheet.

This will contain all the preparation, application information, including coverage rates, normally listed as per coat unless stated otherwise.

Assuming the areas of the bare steel hull to be painted are above the waterline, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend 3 coats of Jotun Conseal Touch-Up.

This is available in many RAL, NCS or BS colours in a matt finish.

This product can be difficult to apply by brush and roller, thinning it 10% with Jotun Thinner No. 7 will aid application.

We have a Trade Counter in Leeds, West Yorkshire.

Unfortunately we do not have a product we can recommend to paint an appliance.

Thank you for the enquiry, please can you provide more information to [email protected] so we can assist with a recommendation.

Assuming the previously painted aluminium chairs have any loose and flaking material removed, they are clean ,dry, sound and prepared as detailed in the technical data sheet we can recommend Bradite One Can.

This is available in many RAL, NCS or BS colours in a matt or eggshell finish.

This can be applied by brush, roller or spray application.

Assuming the frame is steel, it has the rust removed, it is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by Rust-Oleum CombiColor Original.

This is available in many RAL, NCS or BS colours in a satin or gloss finish.

Unfortunately Plygene is a TPO and we do not have a product to recommend that will adhere to this.

Assuming you are looking to paint plastered internal walls, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Tikkurila Muuri.

This is available in a range of colours which are heat resistant to 180°C and white which is heat resistant to 300°C.

Assuming the radiator is clean, dry, sound and prepared as detailed in the technical data sheet you could consider Rust-Oleum CombiColor Original.

It is heat resistant up to 90°C (dry heat), so as long as the surfaces being painted didn't exceed this temperature it should be OK.

But it will have an solvent smell during use and drying.

Rust-Oleum CombiColor is however an industrial product designed for exterior use or interior use in industrial environments so it is not specifically intended for internal home use.

Thank you for the enquiry, we would need more information on what the floor is made of and pictures of the area in question to assist. 

Please send these to [email protected]

The Safety Data sheet can be data sheets tab on the product page. 

Cromadex 903 Two Pack Chromate-Free Etch Primer

Unfortunately this is not a product we can supply, but if you can provide more information to [email protected] we can look into an alternative for you.

Assuming the horse shoes are steel, we would recommend that all the rust is removed prior to application.

Assuming this is done, they are bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by 2 coats of Rust-Oleum CombiColor Original.

This can be mixed in many RAL, NCS or BS colours in a satin or gloss finish.

Assuming you are applying by spray application, the walls are clean, dry, sond and prepared as detailed in the technical data sheet, we can recommend Zinsser AllCoat Interior (Water-Based).

This is a matt finish and can be mixed to many RAL, NCS or BS colours.

Assuming the upvc and cast iron piping are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Bradite One Can.

This is available in many RAL, NCS or BS colours in a matt or eggshell finish.

Unfortunately we do not have a product to recommend for over painting masonry paint applied to patio slabs.

This would need to be removed prior to an appropriate floor paint being applied.

Assuming this is done, a damp proof membrane is present, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Acrylic Floor Paint.

This can be mixed to many RAL, NCS or BS colours in a semi gloss finish.

Assuming the patio is clean, dry, sound and prepared as detailed in the technical data sheet, it is made of one of the substrates listed below, we can recommend Hydron Mona-Guard Nhance.

This is a unique water based modified polysiloxane which provides oil and water repellent properties and lifts the true colour of the substrate.

Brickwork
Concrete
Natural stone
Reconstructed stone and blockwork
Granite
Marble
Terrazzo
Limestone
Sandstone
Concrete pavers, flags and roof tiles
Slate

Thank you for the enquiry, please can you provide more information on the project along with pictures of the area in question to [email protected]

Unfortunately this is not a product we stock.

Tor Elastaseal Fibretex has been discontinued, Tor Elastaseal Z Fibretex is available in 5ltr or 12.5ltr tin sizes.

Assuming you are looking to paint the internal blockwork walls, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser AllCoat Interior (Water-Based)

This is available in many RAL, NCS or BS colours in a matt finish.

Unfortunately we cannot advise on a colour choice, we would recommend viewing a physical colour chart to ascertain a suitable match.

These are normally available to view at Trade paint suppliers such as ourselves in Leeds, or they are for sale here.

We also can offer Colour Sample Sachets to aid choosing a colour.

Assuming the primed container areas to be painted are vertical, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 7500 Alkythane.

This can be mixed in many RAL, NCS or BS colours in a gloss or satin finish.

We would recommend testing for compatibility and adhesion with the previously sourced primer prior to application.

For the roof areas we can recommmend Rust-Oleum Mathys Fillcoat.

This roofing compound is available in black, light or dark grey.

Unfortunately we cannot advise on a colour choice, we would recommend viewing a physical colour chart to ascertain a suitable match.

These are normally available to view at Trade paint suppliers such as ourselves in Leeds, or they are for sale here.

We also can off Colour Sample Sachets to aid choosing a colour.

Assuming the upvc windows are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Kolorbond uPVC Painting Kits.

This can be mixed to many RAL, NCS or BS colours in a satin finish.

The manufacturer offers 10 year adhesion guarantee - 5 year colour fastness guarantee.

Unfortunately we do not have a product we can recommend for painting slate in a shower.

Please can you contact [email protected] with more information on which product you are looking for so we can assist.

Unfortunately no, assuming the timber fence is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser Cover Stain followed by Zinsser AllCoat Exterior (Water Based).

This is available in many RAL, NCS or BS colours in a matt, satin or gloss finish..

Unfortunately we cannot referernce CMYK or RGB percentages, we can mix the paints to many RAL, NCS or BS colours.

Unfortunately we cannot advise on a colour choice, we would recommend viewing a physical colour chart to ascertain a suitable match.

These are normally available to view at trade paint suppliers such as ourselves in Leeds, or they are for sale here.

We also can off Colour Sample Sachets to aid choosing a colour.

Assuming you are painting onto cement based masonry, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser AllCoat Exterior (Water Based)

This can be mixed to many RAL, NCS or BS colours in a matt, satin or gloss finish.

This is available in 1ltr, 2.5ltr, 5ltr or 10ltr tin sizes.

Thank you for the enquiry, we will need more information to assist with this enquiry.

Please can you provide pictures of the area in question, information, along with your order reference to [email protected]

Unfortunatley we cannot advise on a colour choice, we would recommend viewing a physical colour chart to ascertain a suitable match.

These are normally available to view at trade paint suppliers such as ourselves in Leeds, or they are for sale here.

We also can off Colour Sample Sachets to aid choosing a colour.

Assuming the upvc windows are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Kolorbond uPVC Painting Kits.

This can be mixed to many RAL, NCS or BS colours in a satin finish.

The manufacturer offers 10 year adhesion guarantee - 5 year colour fastness guarantee.

The certificates for the Astroflame X-Series Intumescent Fire Pillows can be found in the data sheets tab on the product page.

Yes this product is available to order from the product page below.

Wethertex MP44 Pliolite Spray Wall Coating

Thank you for the enquiry, please can you provide some more information and pictures of the boat so we can see the condition of the hull and assist with a recommendation to [email protected]

Thermoguard Thermostrip PRO can be used to strip many types of paint from metal substrates, while this should not effect the metal work underneath we would recommend testing on a small area prior to full application.

Assuming the aluminium ramp is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Smartkote Protectakote UVR Smooth or Smartkote Protectakote UVR if an anti-slip finish is required.

The ramp must be clean, dry, sound, prepared as detailed in the technical datasheet.

This requires the aluminium to be cleaned, abraded and primed first with Smartkote Protectakote 2K Metal Primer.

Assuming the concrete floor has a damp proof membrane present, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Speed Screed followed by the application of Rust-Oleum Epoxyshield Garage Floor Coating Kit.

This is available in grey, it will cover 25m² per kit.

Thank you for the enquiry, please can you provide more information on the project to [email protected] so we can assist.

HMG and Kapci are two different manufacturers of paints.

Please can you provide more information to [email protected] so we can assist.

Unfortunately no, we can only ship to mainland UK at this time.

Colour Sample Sachets are available to order on the website in your chosen colour. 

Assuming the roller shutter door is UPVC, or a composite, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend the Kolorbond UPVC paint kits.

This is available in many RAL, NCS or BS colours in a satin finish.

Please note any applied paint for application to a roller shutter will wear on the joints and wear it rolls around the drum.

If the roller shutter is galvanised steel, we would recommend Rust-Oleum 3202 Galvinoleum Primer followed by Rust-Oleum 7500 Alkythane.

This is available in many RAL, NCS or BS colours in a satin or gloss finish.

Assuming the epoxy paint has fully cured it would need to be ground or abraded off.

Thermoguard Thermostrip PRO can remove many types of paint including some two pack materials.

If an issue with application has occurred and it has not cured 109 Tool Cleaner could be used.

Assuming the brick fire place is not exposed to direct flame contact, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Tikkurila Muuri.

This is available in a range of colours in a matt finish.

We would recommend testing for compatibility and adhesion prior to full application on any areas that have been previously painted.

This paint can withstand temperatures of 300°C if the white is used, the coloured options can withstand 180°C.

If the area will be exposed to high temperatures it would be best to remove the Zinsser Bulls Eye 1-2-3 primer first as this is not designed for the elevated temperatures.

Assuming the fibreglass is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum CombiColor Multi-Surface.

This can be mixed in many RAL, NCS or BS colours in a gloss finish.

Colour Sample Sachets are available to order on the website in your chosen colour. 

Thank you for the enquiry, please provide more information to [email protected] so we can assist with a recommendation.

We can mix many paints to most RAL, NCS or BS colours. 

We do also stock these Colour Charts.

Colour Sachet Samples are also available to aid choosing a colour.

Thank you for the enquiry, please contact [email protected] with the quantity and size required so we can assist.

Thank you for the enquiry we will need to know what the bath tub is made of to assist with this enquiry, please can you provide more information to [email protected]

Jotun Jotamastic 90 is available in RAL 7037 in a 4.55ltr kit.

Unfortunately Jotun Jotamastic 90 GF is only available in 20ltr kits.

Colour Sample Sachets are available here.

We wouldn't have something suitable for fabric or textile based cases but if the substrate is plastic you could consider the Maston Spraypaint 2K Colours

Thank you for your question, we have contacted you directly for more information.

Rust-Oleum don't recommend a clear coating from their Combicolor range, if an additional clear protective topcoat is required you could consider the Rust-Oleum Hard Hat 2500 Transparent Protection.

Unfortunately this is not a product we have available currently, but we do stock many of Rust-Oleums range of aerosols.

We offer Colour Sample Sachets mixed to most RAL, NCS or BS colours.

We can supply the range of HMG M99 products. 

These can be ordered on the website.

If bare steel, we would recommend cleaning and degreasing the substrate thoroughly in accordance with the product data sheet and then prime using one coat of the Teamac Metaclor Antifouling Primer,
Followed by two coats of the Teamac Chlorvar Chlorinated Rubber Paint. Allow two full weeks before immersing the coating in water.

We would recommend the Stonelux Primer & Undercoat followed by the Stonelux Fireplace Paint providing the surface being painted is a minimum of 10cm away from the heat source.

Unfortunately we do not deliver outside of the UK.

We would recommend testing on a small area for compatibility and adhesion prior to full application.

On new slate tiles adhesion should not be a problem but on older slate there maybe contaminants present that could effect adhesion.

Assuming this is successful, the slate tiles are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend the Smartkote Protectakote Clear Primer Treatment followed by Smartkote Safekote.

This will provide a barefoot friendly anti slip semi gloss finish in a range of colours.

We have contacted you directly for more information.

We can offer Colour Samples Sachets mixed to many RAL, NCS or BS colours.

Yes this is possible, please provide more information and pictures of the area in question to [email protected] so we can assist.

Please can we ask for more information and pictures of what you are looking to paint to be sent to [email protected] so we can assist with a recommendation.

Assuming the previously painted areas, are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Teamac High Performance Polyurethane Topcoat.

This is compatible with most 2 pack coatings, but we would recommend testing on a small area for compatibility and adhesion prior to full application.

This is sold in kit form including the hardener, the coverage rate per coat is 7.5 to 8.5m² per litre.

Assuming the galvanised gutter has any corrosion removed, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Mathys Fillcoat Fibres.

The gutter should be thoroughly degreased and primed with Rust-Oleum Mathys Fillcoat prior to application.

Assuming the polycarbonate is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Kolorbond K2 Set. 

This can be mixed to many RAL, NCS or BS colours in a range of finishes for spray application.

We would recommend testing for compatibility and adhesion on a small area prior to full application as if the plastic has been produced in layers it is possible that the solvents in the K2 may craze the surface of the polycarbonate.

If the polycarbonate is not resistant to solvent crazing the alternative will be Kolorbond Aquatek.

Assuming the bare mdf is clean, dry, sound and prepared as detailed in the technical data sheet, we can recommend Zinsser Bulls Eye 1-2-3 followed by Zinsser Perma-White Interior.

This is available in many RAL, NCS or BS colours in a matt or satin finish.

Thank you for the enquiry, we have contacted you directly by email.

Please see our Fire Certification Application page for the processes for each of the manufacturers.

Unfortunately while we stock fibreglass roofing trims, we do not stock drainage outlets.

Assuming a test for compatibility and adhesion is undertaken prior to full application, the timber previously painted door is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser AllCoat Exterior (Water Based).

This can be mixed to many RAL, NCS or BS colours in a matt, satin or gloss finish.

Assuming the garden slabs are concrete only subject to foot traffic, there is a damp proof membrane present, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-var Acrylic Floor Paint.

This is available in many RAL, NCS or BS colours in a semi gloss finish

Unfortunately we cannot mix paints to automotive paint codes.

Please can you send more information and pictures of the mixer to [email protected] and we can assist with a recommendation.

What is the drum made of?

Is it bare or previously painted?

How can it be prepared?

What chemicals and concentrations will it be exposed to?

We would recommend viewing a physical RAL, NCS or BS colour chart in person to ascertain a suitable match.

These can normally be viewed at trade paint suppliers, alternatively we do sell these here.

Or Colour Sample Sachets are also available.

Assuming the item to be painted is bare steel we would recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion.

If the item to be painted is aluminium, stainless or galvanised steel we would recommend Rust-Oleum 3202 Galvinoleum Primer.

We would not have a product we can recommend for addressing cracks to an asbestos roof, these should be replaced.

Thank you for you message, i have asked our Customer Service team to contact you directly.

Thank you for the enquiry, please can you provide more information on which product to [email protected] so we can assist.

Assuming the metal edges are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend priming them with Zinsser Bulls Eye 1-2-3 followed by Zinsser Perma-White Interior.

Assuming the stone work is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend 405 Tack Primer and 202 Vertical Surface Repair Mortar.

Zinsser AllCoat Exterior (Water Based) can be applied directly to clean, dry, sound and prepared composite doors.

Zinsser AllCoat Exterior Satin (Solvent Based) can also, but Zinsser AllCoat Exterior Gloss (Solvent Based) would require priming first with Zinsser Bulls Eye 1-2-3.

We would recommend the use of the waterbased product unless the temperatures at application are below 10°C.

Thank you for the enquiry, please can you provide more information and pictures of the application to [email protected] and we can assist you with a recommendation.

Assuming the clay roof tiles are clean, dry, sound and prepared as detailed in the technical data sheet, we can recommend Teamac Acrylic roof coating.

This is available in a range of colours in a matt finish.

Unfortunately we do not stock powder coating materials.

We have contacted you directly.

Please can you provide more information to [email protected] so we can assist.

Assuming the walls are brick, they are not exposed to temperatures in excess of 300°C if white is used or 180°C if a tinted colour is used, they clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Tikkurila Muuri.

This is available in a range of colours.

Assuming the upvc roller door is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend the Kolorbond UPVC Painting Kits.

This is available in many RAL, NCS or BS colours in a satin finish.

Please note that a paint coating may wear on joints and where the panels roll around the drum.

Assuming the steel chassis is clean, dry sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by Rust-Oleum CombiColor Original.

This is available in many RAL, NCS or BS colours in a satin or gloss finish.

We would recommend all corrosion is removed prior to application.

We would recommend testing for compatibility and adhesion prior to full application on the previously painted areas.

Assuming this is successful, the radiator is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Maston Spraypaint 2K Colours.

This is available in many RAL, NCS or BS colours in a matt, semi gloss or high gloss finish.

If there are any bare metal areas, these should be primed with Maston Spraypaint 2K Primer. 

These paints can be used on areas subject to appoximately 150°C.

Unfortunately we do not have a product we can recommend for this application.

Unfortunately no, we have our trade counter in Leeds, but we can ship to most mainland UK addresses.

Unfortunately we do not have a product to recommend for this application.

This product can be mixed to many RAL, NCS or BS colours. 

Colour Charts are available here, or at our or other trade paint suppliers trade counters.

Assuming this is regarding Zinsser Allcoat Exterior for brush, roller or airless spray application, the ambient temperature would determine wether solvent or water based should be used.

For cooler temperatures but above 5°C minimum we would recommend the sovlent based, for warmer temperatures during the summer water based would be better suited.

Assuming the upvc is clean, dry, sound and prepared as detailed in the technical data sheet any of the water based or the satin solvent based can be applied directly.

If you wish to use Zinsser AllCoat Exterior Gloss (Solvent Based), the upvc must be primed first with Zinsser Bulls Eye 1-2-3.

Assuming the beach hut is bare timber, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser Cover Stain and Zinsser AllCoat Exterior (Water Based).

This can be mixed to many RAL, NCS or BS colours in a matt, satin or gloss finish.

Assuming the plaster mantel piece is not subject direct flame contact, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Tikkurila Muuri.

This is avaialble in a range of colours, in white this paint can withstand temperatures of upto 300°C and upto 180°C for the other tinted colours.

This product covers 18m² per pack in one coat.

You will require 4 packs for 2 coats of 30m².

Regarding an anti-slip aggregate, Fosroc Nitoflor Anti-Slip Grains could be used. 

The coverage rate is 1 x 0.9kg to 5kg of paint.

Thank you for the enquiry, we have contacted you directly with more information.

Thank you for the enquiry, we will need to know more information on what the powder coated items are to assist with this. 

Please contact [email protected].

Thank you for the enquiry, we would need to know more information on what is to be painted to assist. 

Please contact [email protected]

Thank you for the enquiry, please provide more information to [email protected]

We have RAL, NCS and BS colour charts available to view at our trade counter in leeds.

These are normally available to view also at most local trade paint supplier, alternatively we do sell the charts here.

We also offer Colour Sample Sachets to aid colour choice.

Assuming the garage door is previously painted metal, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum CombiColor Original.

If there are any areas of bare steel they should be primed first with Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion or for galvanised steel or aluminium Rust-Oleum 3202 Galvinoleum Primer.

Cromadex 222 One Pack Fast Air Drying Alkyd Topcoat Aerosol can be mixed to many RAL, NCS or BS colours including some metallics in an eggshell, semi gloss, matt or gloss finish.

Assuming the radiator is bare, clean, dry, sound and prepared as detailed in the technical data sheet this could be used once primed with Cromadex Super Build Primer Aerosol.

Please note as these are solvent paints they will smell during application, curing and the first few heat cycles.

Assuming the upvc is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Kolorbond uPVC Painting Kits.

This is available mixed to many RAL, NCS or BS colours including RAL 7033 in a satin finish.

Assuming the new render is cement based, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Wethertex AP77 Flexible Smooth Masonry Paint.

This can be mixed to many RAL, NCS or BS colours in a matt finish.

You could consider the Coo-Var Glocote System.

This fluorescent paint system is available in a range of colours.

Assuming you mean Sherwin-Williams Macropoxy L524 this is indefinitely overcoatable with epoxy systems provided the surfaces to be coated have been suitably cleaned. 

Thank you for the enquiry, please can you provide more information on the boat, what it is made of and if it is bare or previously painted to [email protected]

Assuming the mineral based boards are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Tikkurila Muuri.

This is available in a range of colours in a matt finish.

Please note in white this is resistant to 300°C in the tinted colours only 180°C.

Assuming the timber is not exposed to direct flame contact, it is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Stonelux Primer & Undercoat followed by Stonelux Fireplace Paint.

This is available in a range of colours in many stone finishes.

Please note this is resistant to 300°C but must be a minimum of 10cm from any heat source .

Thank you for the enquiry, we would not recommend an aerosol paint for this application, the film build from an aerosol is thin and for the expected use on a bench it would not last long.

Assuming the iron bench is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by Rust-Oleum CombiColor Original.

This can be mixed to many RAL, NCS or BS colours in a satin or gloss finish.

This can be applied by brush, roller or spray application.

Assuming the outdoor patio slabs are not subject to vehicle traffic, they have a damp proof membrane present, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 7200 Floorcoat PU.

This is available in many RAL, NCS or BS colours in a satin or gloss finish.

Please note the drying times are stated at 20°c, at this time of year these will be longer and the paint must be kept dry during this time.

Thank you for the enquiry, please can you provide more information and pictures of the area in question to [email protected] so we can assist.

Thank you for the enquiry, please contact [email protected] with more information on which product the thinner is for.

Unfortunately we do not have a product suitable for application to the external glass roof.

Unfortunately we do not have a product we can recommend for this application to a cooker.

Rust-Oleum Furniture & Skirting Board Paint is not designed to be thinned.

Thank you for the enquiry, please can we request more information and pictures of the area are sent to [email protected] and we can assist further.

This paint is not available in sample sizes, but we do sell Colour Sample Sachets of a generic paint suitable for aiding a colour choice, but this is not suitable for application to a floor.

Unfortunately we do not stock Cuprinol, but we do stock masonry paints such as Wethertex PP77 All Weather Pliolite Masonry Paint - Smooth Matt which can be mixed to many RAL, NCS or BS colours.

We would recommend viewing a physical colour chart to ascertain a suitable match to the desired silver birch.

Thank you for the enquiry, please can we ask for teh information below to be sent to [email protected]

What are the barcodes made of?

What level of traffic will the area receive? Is there fork lifts of vehicles?

Is the floor bare concrete or previously painted?

What preparation can be undertaken prior to application?

We would need to know which product you are looking for, please contact [email protected] with more information. 

We would recommend the RAL, NCS and BS Colour Charts. 

Thank you for the enquiry, please can you provide more information on the project to [email protected] so we can assist with a recommendation.

To aid choosing a colour we do offer Colour Sample Sachets or we can offer a Colour Match Service.

Unfortunately we do not have a product to recommend for this application.

Assuming the concrete roof tiles are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Cromar Renocoat Roof Tile Renovation Paint.

This is available in a slate grey or dark brown with a matt finish.

Unfortunately we do not have a product to recommend for this application.

Assuming the aluminium windows are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Kolorbond DecoPro.

This is available in many RAL, NCS or BS colours in a matt, satin, semi-gloss or gloss finish.

Thank you for the enquiry, please can you provide pictures of this area and information on what the panels are made of to [email protected]

Unfortunately these are not products we stock at this time.

Unfortunately no, with have a trade counter in Leeds and ship to most mainland UK addresses.

This can be thinned slightly with clean water. 

The spray gun should have a tip size of 1.8 to 2.4mm for using this product.

Assuming the lime render is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser AllWeather Exterior Masonry Paint (Solvent Based).

This can be mixed to many RAL, NCS or BS colours in a matt finish.

Assuming the concrete is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Ennis-Flint Cataphos Chlorinated Rubber (Premium).

This is available in black, green, red, white or yellow.

Unfortunately we cannot mix paints to an automotive paint code, but assuming the bonnet is not exposed to temperatures over 150°C it is bare steel, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Maston Spraypaint 2K Primer followed by Maston Spraypaint 2K Colours.

This can be mixed to many RAL, NCS or BS colours in a matt, semi-gloss or gloss finish.

Assuming a level of fire protection is not required, the steel is clean, dry, sound and prepared as detailed in the technical data sheet you could consider Teamac Extra Brilliant Aluminium Paint.

This has a satin finish.

Assuming the steel is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend 404S Epoxy Metal Primer followed by 310 Chemical Resistant Coating.

This is available in a range of colours in a gloss finish. 

The technical data sheets can be found in the data sheets tab on the product page.

All product data sheets and safety data sheets for every product on the website can be found in the data sheets tab on the product pages.

We would need to know more information on the application to recommend one of the suitable topcoats for your application. 

Please contact [email protected] with more information.

Unfortunately we do not have a product suitable for this application.

Unfortunately we do not sell gelcoat, we would recommend checking with the gelcoat manufacturer what their preparation and primer requirements will be.

Unfortunately we do not have a product to recommend for this application.

Epoxy floor paints are not uv stable so any new application will also discolour over time.

Assuming the previously applied 2 pack paint is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend 303 Epoxy Floor Paint.

The previously applied paint must be prepared mechanically.

We would recommend testing on a small area for compatibility and adhesion prior to full application.

For 70m² you would require approximately a 15kg tin per coat.

Zinsser B-I-N can permanently block many types of odours. 

For brush application this time of year assuming the composite doors and fbreglass are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser AllCoat Exterior Satin (Solvent Based).

This is available in many RAL ,NCS or BS colours.

Unfortunately no, we do not have a clear product for application to rust or bare metal.

Thank you for the enquiry, please contact [email protected] with more information so we can assist.

Unfortunately we do not have a product to recommend for this application.

Yes Zinsser AllCoat Exterior can be used internally, the water based is lower odour and would be better for internal application.

If the doors are UPVC this can be applied directly to a prepared surface, if the doors are bare timber they should be primed first with Zinsser Cover Stain.

Thank you for the enquiry, please can you provide the information below to [email protected].

Is there a damp proof membrane under the concrete floor?

What is the screed and is it suitable to be over painted and if no damp proof membrane is present is it suitable to be applied without one?

Please also send the technical data sheet of the screed that has been applied.

Thank you for the enquiry, please can you provide pictures of the peeling area to [email protected]. 

Assuming the failing coatings are removed, the timber is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend 2 coats of Zinsser Cover Stain followed by 2 coats of Zinsser AllCoat Exterior (Solvent Based) to all areas.

3 coats should be applied to any areas exposed to pooling water.

This is not a product we stock, but assuming the external face of the wall is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Sika Water Seal.

The walls must be dry for application.

Our accounts team will have this to you shortly.

Unfortunately we do not have a reflective black paint to recommend, changing the colour to a lighter colour would help in avoiding a door getting too hot.

Thank you for the enquiry, please contact [email protected] with more information so we can assist.

Assuming the composite fireplace is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Stonelux Primer & Undercoat followed by Stonelux Fireplace Paint.

Surfaces painted with Stonelux Fireplace Paint must be a minimum of 100mm (10cm) away from any heat source, this paint can withstand upto 300°C.

This is available in a range of finishes.

Stonelux Colour Sample Pots and Stonelux Colour Charts are available.

Assuming the wooden fence is stained or previously painted, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Hydron Nu-Guard AG.

If the timber is bare it would need to be sealed first.

Assuming the pvc wall panels are not exposed to direct water contact, they are internal, clean, dry, sound and prepared as detailed in the technical we can recommend Zinsser Bulls Eye 1-2-3 followed by Zinsser Perma-White Interior.

This is available in many RAL, NCS or BS colours in a matt or satin finish.

We would recommend testing for compatibility and adhesion on a small area prior to full application.

Assuming the metal container roof is painted, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Mathys Fillcoat.

This is available in black, light grey or dark grey.

Yes, this would not be suitable for application to an area exposed to splashes from a shower.

Unfortunately we do not have a product to recommend for this application.

You could consider the Rust-Oleum Kitchen Cupboard Paint range.

This is available in a matt, or satin finish.

Assuming the composite door is bare, clean, dry, sound and prepared as detailed in the technical data sheet you could consider Kolorbond uPVC Painting Kits.

This can be mixed to many RAL, NCS or BS colours in a satin finish.

Assuming the drain covers are galvanised, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Watco Galvaprime followed by Watco Safety Grip Cold Cure.

This is available in a range of colours.

Assuming the walls are plastered, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Tikkurila Muuri.

This is available in a range of colours in a matt finish.

This is resistant to heat upto 300°C in white or 180°C in a tinted colour.

We would recommend the previously applied anti-graffiti coating is completely removed prior to application of any paint to ensure adhesion.

Once this is done and the walls are painted in the colour you require, the paint is fully cured, the area is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 4900 Polycoat 2K.

This is available in a matt or gloss finish.

We would recommend testing for compatibility and adhesion prior to full application.

We would recommend addressing the cause of the damp as anti mould paint may not deal with the issue.

Once the cause is corrected, assuming the plastered wall and ceiling are taken back to bare plaster, any mould is removed we can recommend Coo-Var Anti-Damp Paint.

This is designed as a primer coat and contains a reactive agent which will conbine with any remaining surface moisture.

This can then be over painted with a paint such as Zinsser Perma-White Interior.

This is available in many RAL, NCS or BS colours in a matt or satin finish.

This is not a product we can reference, please can you provide more information to [email protected]

Assuming the grp door is bare, clean, dry, sound and prepared as detailed in the technical data sheet you could consider the Kolorbond uPVC Painting Kits.

This can be mixed to many RAL, NCS or BS colours in a satin finish.

Thank you for the enquiry, please can you provide more information on what the wet room floor is made of or coated with, along with pictures of the area in question to [email protected] so we can assist with a specification.

Assuming the inside of the windows are upvc, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Kolorbond uPVC Painting Kits.

Two coats are required, this is available in many RAL, NCS or BS colours in a satin finish.

We would not recommend applying this system if the temperatures are below 10°C.

Thank you for the enquiry, unfortunately we do not have a sealant suitable for this application.

Thank you for the enquiry, please can you provide more information on the materials the door is made of and if it is bare or previously painted to [email protected]

Thank you for the enquiry, this product is available, we have contacted you directly.

Assuming the metal is bare steel, it is not subject to traffic, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by 2coats of Rust-Oleum CombiColor Original.

This is available in many RAL, NCS or BS colours in a satin or gloss finish.

Unfortunately we do not have a product available in this colour, but Ardenbrite Metallic Paint (Solvent Based) is available in old penny bronze.

this can vary for each product, please provide more information to [email protected] so we can assist.

Wethertex AP77 Flexible Smooth Masonry Paint can be mixed to 10 B 15.

 Unfortunately we do not have a clear product we can recommend for this application.

Thank you for the enquiry, please can you provide more information and pictures so we know what the pipe is made of to [email protected]

While a product such as Coo-Var Vandalene Anti Climb Paint could be applied, it should only be used on areas normally above 2metres or at heights your local authorities specified to avoid contact with passers by.

Zinsser AllCoat Interior (Solvent-Based)is suitable for this application.

We would recommend testing for compatibility and adhesion between the applied primer and the Zinsser AllCoat Interior (Solvent-Based) prior to full application. 

No additional primer woudl be required on the bare mdf areas, but we would recommend application of three coats, teh bare mdf must be clean, dry, sound and prepared as detailed in the techincal data sheet. 

Thank you for the enquiry, please can you provide pictures of the floor and information on the material tiles are made of to [email protected] and we can assist further.

Assuming the walls to be painted are cement based, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Wethertex PP77 All Weather Pliolite Masonry Paint - Smooth Matt.

This can be mixed to many RAL, NCS or BS colours in a matt finish.

We would not recommend applying a colour wash over the painted surface.

I think you may be referring to Resimac 508 UVPU.

Unfortunately not at this time, only mainland UK addresses.

Thank you for the enquiry, please provide more information to [email protected] so we can assist.

Assuming the rust is removed, the steel chassis is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Mathys Noxyde Plus.

This is available in a range of colours in a satin finish.

Assuming the fibreglass is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Teamac High Performance Polyurethane Topcoat.

This can be mixed on many RAL, NCS or BS colours in a gloss finish.

2 coats in a colour followed by one in clear would be recommended.

Assuming the aluminium angle is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Bradite One Can Matt.

This can be mixed to many RAL, NCS or BS colours and no primer is required.

Assuming the damp patches are not caused by condensation, the wall is clean, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Anti-Damp Paint.

This can be applied to slightly damp substrates and is designed to be over painted with emulsion paints.

We are sorry to hear of the issues you are having with the product, please can you provide more information on the issue and which Maston aerosol this is regarding to [email protected] and we can look into this for you.

Unfortunately this is not a product we currently supply, but you could consider Zinsser AllCoat Exterior Satin (Solvent Based)as an alternative.

This can be mixed to many RAL, NCS or BS colours.

Thank you for the enquiry, please can you provide more information on the tile and picutres of the area in question to [email protected] so we can assist.

Thank you for the enquiry, please can you provide more information and pictures of the area in question to [email protected]

Unfortunately unless the rust is removed any applied paint will fail.

Assuming the trailer is steel, is it clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 569/580 QD Metal Primer followed by two coats of Rust-Oleum 7500 Alkythane.

This is available in many RAL, NCS or BS colours in a gloss or satin finish.

Assuming the timber floor is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Acrylic W/B Road Line Paint.

This is available in many RAL, NCS or BS colours and can be applied directly to wood.

Assuming the plastic drain pipes are upvc, they are bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser AllCoat Exterior Satin (Solvent Based).

This can be mixed to many RAL, NCS or BS colours.

We would recommend viewing a physical colour chart in person to ascertain suitability of a colour to match.

This paint can be applied down to temperatures of 5°C.

Colour Sample Sachets are also available to aid choosing a colour.

We also offer a Colour Match Service.

Assuming the aluminium tank is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Teamac Zinc Phosphate Primer followed by Teamac Metalcote Plant Enamel.

The aluminium must be cleaned, degreased and etched prior to application with Teamac Mordant Solution (T Wash) or grinded with aluminium oxide grit or discs.

This can be mixed to many RAL, NCS or BS colours in a gloss finish.

Yes, we have many options depending on what the project is. 

Please provide more detailed information to [email protected] so we can assist.

Thank you for the enquiry, please can we ask for more information on the project be sent to [email protected] so we can assist with a recommendation.

RSL Resuflor HB Special Colours is available mixed to RAL 6016. 

There is a 5 day working lead time for special colours.

Thank you for the enquiry, please can you provide more information on the application to [email protected]

Increasing the airflow will help with condensation issues.

Assuming the internal walls are painted, we would recommend the areas that have been subject to condensation and mould are cleaned and treated with N-Virol Suretherm Goodbye Mould Cleaning Spray prior to application of N-Virol Suretherm Goodbye Mould Thermal Anti Condensation Paint.

This can then be overpainted or wall papered over without affecting the performance.

We would recommend Hydron AG3 Graffiti Remover for this application, it can remove most aerosol graffiti from non porous substrates.

Assuming the aluminium frame is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Bradite One Can.

This is available in many RAL, NCS or BS colours in a matt or eggshell finish.

Assuming the area with condensation is internal plastered walls, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend N-Virol Suretherm Goodbye Mould Thermal Anti Condensation Paint.

The coverage rate is 8m² per litre per coat, two coats are required.

For 40m² you would require approximately 10ltr.

Prior to application and mould should be cleaned and treated with N-Virol Suretherm Goodbye Mould Cleaning Spray.

Thank you for the enquiry, please can you provide more information to [email protected] so we can assist with a recommendation.

Thank you for the enquiry, please provide more information to [email protected] so we can assist.

This is not available in sample pots but we can offer generic Colour Sample Sachets to aid choosing a colour.

N-Virol Suretherm Goodbye Mould Thermal Anti Condensation Paint aids in the retention of heat within a room for the purpose of reducing condensation and mould growth.

Any paint applied is only microns thick and is not a replacement for physical insulation products.

For Keim products to be used for this application, all the existing coatings would need to be removed, allowing the substrate to thoroughly dry out prior to application.

The area must be clean, dry, sound and prepared as detailed in the technical data sheet, primed with Keim Ecosil Grund followed by Keim Ecosil-Me.

This is available in many colours in a semi-matt finish.

Assuming the application is to bare solid timber that is a minimum of 12mm thick, approval is sought from building control prior to application, you could consider Zeroflame Fire Retardant Treatment for this application. This can achieve Euroclass B s2 d0 (replaces UK Classes ‘0’ and ‘1’ BS 476 Part 6/7*).

This cannot be used on mdf, osb or plywood to acheive Euroclass B.

We stock many floor paints that can be mixed to many RAL, NCS or BS colours.

We do offer Colour Sample Sachets of a generic paint (not a floor paint) to aid colour choice.

Unfortunately we cannot mix to automotive paint codes, we can mix to many RAL, NCS or BS colours. 

We can offer Colour Sample Sachets mixed to these to aid choosing a colour.

Unfortunately this product is not available in the UK.

Colour Charts are available to purchase, we mix to RAL, NCS or BS colours.

You could consider mineral based paint options from Graphenstone  and Keim.

Unfortunately we do stock Vactan rust converter, we would recommend checking with the manufacturer of the rust converter regarding their preparation requirements prior to over painting.

We would also recommend testing on a small area prior to full application for compatibility and adhesion.

Thank you for the enquiry, please can you provide more information on what the plate is made of, how it can be prepared, if it is in direct flame contact, distance from a heat source to [email protected] we can assist further.

Assuming the plastic drain pipes are UPVC, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum CombiColor Multi-Surface.

This can be mixed to many RAL, NCS or BS colours in a gloss finish.

Assuming the painted iron drain pipes are also clean, dry, sound and prepared as detailed in the technical data sheet with no bare metal areas exposed the same paint could be used.

We would recommend testing for compatibility and adhesion on a small area prior to full application.

Thank you for the enquiry, please can you provide more information and pictures of the cladding, including wether you are painting the metal sheeting side or the asbestos to [email protected] 

Thank you for the enquiry, please can you provide more information on what the paint is to be used on, how the substrates will be prepared, temperature requirements to [email protected] 

All data sheets can be found on the product pages in the data sheets tab.

Our Chartwell Green formulation is custom, it does not have a BS colour code.

Unfortunately Hydron do not make samples of this product.

Unfortunately we do not have a product we can recommend for this application.

Assuming the primed door is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend one of the Selemix Direct 7-53 range of products. 

This is available in many RAL, NCS or BS colours in many sheen levels.

As the primer is unknown we would recommend to test on a small area prior to full application for compatibility and adhesion.

All preparation and application information are in the product data sheet, this can be found in the data sheets tab on the Rust-Oleum CombiColor Original page.

This paint can be applied when temperatures are 5°C and above.

Unfortunately we do not have an alternative to the Rust-Oleum Worktop Transformation Kit  that we can recommend for this application.

Thank you for the enquiry, unfortunately we cannot mix directly to a Farrow & Ball colour we can mix to many RAL, NCS or BS colours.

We have contacted you directly by email with the closest match available.

We would recommend viewing a physical colour chart or ordering Colour Sample Sachet to ascertain suitability.

Assuming the radiator is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Maston Spraypaint 2K Colours.

This can be mixed to many RAL, NCS or BS colours in a matt, semi -gloss or high gloss finish.

We would recommend to test on a small area for compatibility and adhesion prior to full application.

Thank you for the enquiry, please provide more information and pictures of the areas in question to [email protected] so we can assist with a recommendation.

Thank you for the enquiry, please can you provide more information to [email protected] so we can assist with a recommendation.

The Anti-Climb Paints  we stock are only available in black.

Zinsser Mould Killer & Remover is for use against fungi, moulds and algae on internal surfaces such as tiles, wood, plaster, and wallpaper.

Zinsser Mould Killer and Remover is water based and ready for use.

Thank you for the enquiry, please provide the information below to [email protected] then we can assist you with a recommendation.

Environment - interior or exterior
Substrate – concrete, power floated, porous? Timber or metal
If screed applied what is it, also provide TDS if possible
Location – garage, warehouse, domestic
Condition – bare or previously painted
Exposure – foot traffic, vehicles, forklifts, chemicals
Size of area to paint
Colour required
Finish required, matt satin or gloss
Antislip?
Application- who will be applying it>
Application timescale
Level of preparation prepared to undertake – grinding floor prior to application?

Assuming the paint on the metal cabinet is clean, fully cured, dry, sound and prepared as detailed in the technical data sheet we can recommend Hydron Nu-Guard AG.

This is a single pack external coating designed to give effective protection against both fly-posting and graffiti.

This is available in clear and also a range of colours in a semi-matt finish.

We would recommend to test on a small area prior to full application for compatibility and adhesion.

Assuming the render is fully cured, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Tikkurila Muuri. 

This can with resist dry heat upto 300°C in white and 180°C in the range of tinted colours.

This is not suitable for direct flame contact. 

Thank you for the enquiry we have many roofing products that contain fibreglass strands or reinforcement matting.

Please can you provide more information and pictures of the roof to [email protected] and we can assist you with a recommendation.

Unfortunately no, we do not have a product to recommend for this application. 

Fire Certificate Application

Unfortunately we do not have a paint suitable for application to a slate roof.

N-Virol Suretherm Goodbye Mould Thermal Anti Condensation Paint has been specifically designed to reduce condensation from forming on treated surfaces.

It's unique thermal properties make it perfect for use on cold walls and ceilings in your home or office which may be susceptible to condensation, mould and heat loss.

A paint coating will not provide the same insulation properties as a physical insulation board or roll.

Thank you for the enquiry, please can you provide pictures of the area in question and further information on what the tiles are made of to [email protected] then we can assist with a recommendation.

Unfortunately no, this product has been discontinued. 

Rust-Oleum CombiColor Original is available and this can be mixed to many RAL, NCS or BS colours in a satin or gloss finish.

Thank you for the enquiry, please can you provide more information on the condition and construction of the walls in question along with pictures of them to [email protected]

Assuming you are painting above the waterline, the hull is previously painted, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Teamac Marine Undercoat followed by Teamac Marine Gloss.

This is available in many RAL, NCS or BS colours in a gloss finish.

We would recommend to test for compatibility and adhesion prior to full application.

Unfortunately this is not a product we can supply.

Assuming the porcelain tiles are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Tile Transformation Kit.

This is available in Aspen white.

You can order Rust-Oleum Premium Washable Kitchen Cupboard Paint from the product page. 

We can ship through out mainland uk.

Please see our Colour Match Service page, complete the form and send to us with your samples to be matched.

Assuming the boards are a mineral board, they are bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Tikkurila Muuri. 

This is resistant to dry heat upto 300°C in white or 180°C in the range of tinted colours.

This is not suitable for direct flame contact.

Thank you for the enquiry, please can you provide more information on what the pvc object to be painted is, with pictures of it to [email protected] the we can assist with a recommendation.

Assuming the kitchen cupboards are a laminate, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend to primer first with Zinsser B-I-N followed by 2 coats of Zinsser Perma-White Interior.

This is available in many RAL, NCS or BS colours including a Ready mixed white in a satin or matt finish.

This is scuff and scrub resistant.

Please see the link below to order. 

Keim Colour Samples

Thank you for the enquiry, please can we ask for more information and pictures of the area to be sent to [email protected]

Where is the concrete floor? Is it domestic or a commercial area?

What level of traffic does the floor receive?

If a screed was suitable, what depth do you have to work with?

It is recommended to clean out spray equipment with a proprietary Gunwash cleaner.

This product is available in many sheen levels from super matt 0% through to gloss at 70%+. 

A satin finish is the most popular, but we would recommend consulting the window manufacturer on what sheen level the windows you are looking to match are.

Unfortunately no, Rust-Oleum Universal Hammered Finish All Surface Paint Aerosol is only available in a copper finish. 

Assuming a brush or spray applied paint is suitable you could consider Coo-Var Hammercote Hammered Finish.

This is available in a range of colours including a blue.

Thank you for the enquiry, please can we ask for pictures of the wall in question along with information on the walls construction such as if it has a cavity, is if it is rendered and what type of render is used to [email protected]

Assuming the steel caps are only exposed to a dry heat not exceeding 90°C, they are clean, dry, sound and prepared as detailed in the technical data sheet you can consider Rust-Oleum CombiColor Original.

This is available in a range of colours, in a satin or gloss finish.

We can mix many of the paints we stock to RAL, NCS or BS colours.

Please can you provide more information on what you are looking to paint to [email protected] and we can assist with a recommendation.

For brush or roller or airless spray application to these roof panels assuming the are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser AllCoat Interior (Solvent-Based).

This can be mixed to many RAL, NCS or BS colours in a matt finish.

Assuming the concrete slabs are subject to only foot traffic, there is a damp proof membrane present, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Acrylic Floor Paint - Special Colours.

Temperature for application and curing must be over 10°C. 

This can be mixed to many RAL, NCS or BS colours in a semi gloss finish.

Thank you for the enquiry, please can we ask for some more information and pictures of the floor to be sent to [email protected].

Please note that we can only ship to mainland UK addresses at this time.

Thank you for the enquiry, please can we ask for pictures of the area and more information to be sent to [email protected] so we can assist further.

Assuming the aluminium table is polyester powder coated or bare aluminium, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Bradite One Can Eggshell in an eggshell finish.

This is available in many RAL, NCS or BS colours. 

This may wear or weather over time with use but can be reapplied.

Assuming the tiles to be painted are bare ceramic, they are not exposed to direct flame contact or temperatures of 300°C we can recommend Stonelux Primer & Undercoat followed by Stonelux Fireplace Paint.

This is availabe in a range of colours in many stone finishes.

Stonelux Colour Charts and Stonelux Colour Sample Pots are available to aid colour choice.

Assuming the timber garden seating is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend the Osmo Decking Oil  or the Osmo Natural Oil Woodstain.

These are both available in a slight different range of colours and finishes.

For all exterior softwoods we would recommend that the Osmo WR Base Coat is applied beforehand.

Rust-Oleum CombiColor Original can be applied by brush, roller or spray application, this can be thinned upto 10% by volume with Rust-Oleum 7301 CombiColor Thinner.

If the paint is over worked as it cures this could leave brush marks.

Yes we stock many epoxy floor paints. 

To make sure we recommend a suitable product please can you send the information below to [email protected]

Environment - interior or exterior

Substrate – concrete, power floated, porous? Timber or metal

If screed applied what is it, also provide TDS if possible

Location – garage, warehouse, domestic

Condition – bare or previously painted

Exposure – foot traffic, vehicles, forklifts, chemicals

Size of area to paint

Colour required

Finish required, matt satin or gloss

Antislip?

Application- who will be applying it>

Application timescale

Level of preparation prepared to undertake – grinding floor prior to application?

Assuming the metal roofing sheets are clean, dry, sound and prepared as detailed in the technical data sheet you could consider Rust-Oleum Mathys Noxyde Plus for spray application.

Or if your method of application will be brush and roller you could consider Rust-Oleum Noxyde Pegarust.

These are both available in a range of colours.

Assuming the laminated kitchen cupboards are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Kolorbond DecoPro.

This is a brushable two pack paint that can be mixed to many RAL, NCS or BS colours in a range of finishes including satin.

We would recommend to test for compatibility and adhesion on a small area prior to full application.

Thank you for the enquiry, please can you provide more information and pictures of the area to [email protected]

Unfortunately we do not have a product we can recommend for this application that could be applied in just one coat. 

But assuming the metal gates are steel, any rust or corrosion is removed, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum CombiColor Original.

Two coats would be required.

Any bare steel areas must be primed first with Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion.

Thank you for the enquiry, we will need further information to assist with this enquiry, please can you send teh answers to the questions below and pictures of the area to [email protected].

Is the are to be painted around a wood burner, open fire or gas fire?

How far away from the heat source is the area to be painted?

Will the area to be painted be subject to directly flame contact?

Please can you provide pictures of the area along with information on the use of the fire place to [email protected] so we can look into this for you.

Unfortunately we cannot mix directly to a Farrow & Ball colour code, but we can mix to many RAL, NCS or BS colours. 

The closest colour we can mix is S 4005-B80G, but this is described as being different and not a close match. 

We would recommend viewing a physical NCS colour chart to ascertain if this is close enough for your application. 

We can also mix a Colour Sachet Sample to this colour.

Unfortunately we do not have a reflective paint to recommend that can be walked on. 

You could consider Heskins Safety-Grip Photoluminescent Anti-Slip Tape Rolls .

Unfortunately we do not have a paint to recommend for this application, but you could consider using Sika Setting Sand as the jointing material as this resists weeds. 

Blackfriar Professional Solar Reflective Paint White can be applied to clean, dry, sound and prepared masonry surfaces.

Assuming the outside step is bare concrete, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 7200 Floorcoat PU used with Rust-Oleum Non-Skid Additive NS 100.

This can be mixed to many RAL, NCS or BS colours and Chartwell Green in a satin or gloss finish.

Assuming the cast iron bench is bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by Rust-Oleum CombiColor Original. 

This is available in a satin or gloss finish mixed to Chartwell Green, but this is not metallic.

Unfortunately to rectify this we would recommend to sand back the oil and either recoat in a lighter shade of  Rubio Monocoat Oil Plus 2C (you could also add pure to the mahogany oil you have to lighten the colour) or sand it all the way back, add Rubio Monocoat Precolor Easy mint white which counteracts the redness in wood and then apply the oil again.

If a tape is suitable you could consider Heskins Glass Bead DOT-Approved Reflective Tape.

This is available in white, red or yellow.

For a fluorescent paint option you could consider the Coo-Var Glocote Fluorescent Paint System.

Assuming the previously painted gates are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum CombiColor Original.

This is available mixed to many RAL, NCS or BS colours in a satin or gloss finish. 

If there is any bare galvanised areas, these shoudl be primed first with Rust-Oleum 3302 CombiPrimer Adhesion Primer.

Assuming the patio slabs are concrete, there is is a damp proof membrane under the slabs, they are bare, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend the system below.

 The bare concrete must be acid etched prior to application.

Coo-Var Acid Etch

Followed by 3 coats of Coo-Var Anti-Slip Acrylic Floor Paint with the first coat thinned 10% with clean water.

Unfortunately we cannot reference caravan manufacturer paint codes, we can mix to many RAL, NCS or BS colours. 

We do offer a Colour Match Service if you would like to send in a sample.

Assuming the wooden bench hut is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Wethertex OT25 Wood-Flex Satin Opaque Timber Paint.

This is available in many RAL and BS colours.

Please can you provide more information and pictures to [email protected] so we can look into this for you.

Unfortunately we do not have a product we can recommend for this application to a gas appliance.

We can mix many paints to many RAL, NCS or BS colours. 

We would recommend to view a physical colour chart in person to ascertain a suitable match to your windows.

We have these available to view at our trade counter in Leeds or they can be purchased on the link below.

Colour Charts.

We can also offer a Colour Match Service.

During preparation for painting these imperfections and scratches maybe removed during the sanding process. 

If these are still present a fibreglass repair kit could be used.

Once the roof is clean, dry, sound and prepared as detailed in the technical data sheet it could be painted with Teamac Metalcote Undercoat followed by Teamac Metalcote Plant Enamel.

This can be mixed to many RAL, NCS or BS colours in a gloss finish.

We would recommend Teamac Metaclor Antifouling Primer for this application prior to use of an antifoul such as Teamac Antifouling D Plus for professional use or Teamac Protector II Antifouling.

But this is not a high build product.

Thank you for the enquiry, please can you provide more information and pictures of the area in question to [email protected]

Assuming the concrete slabs are bare, clen, dry, sound and prepared as detailed in the technical data sheet you could consider Flag Heavy Duty Elastomeric Floor Coating (Anti-Slip)

This is available in a range of colours in a satin finish.

Unfortunately we cannot recommend a colour choice.

We do have physical RAL, NCS and BS colour charts available to view at our trade counter in Leeds.

If you are not local, many local trade paint suppliers will also have the same industry standard colour charts to choose from.

Alternatively if you wish to send a sample in you could use our Colour Match Service.

All available colours are shown on the product pages using the pick a colour button.

We can mix many paints to RAL, NCS or BS colours. 

We cannot mix directly to a Dulux colour but please email [email protected] with the Dulux code and we can see if we can find an approximate match.

Thank you for the enquiry, please can you provide pictures of the area to be painted and information on the paint you wish to use with the primer to [email protected].

Unfortunately no we do not have a similar paint product for this application to a timber decking. 

If the timber decking is bare you could consider Osmo Anti-Slip Decking Oil for a clear anti-slip option.

Unfortunately Wethertex CP80 Clad-Seal Steel & Cladding Coating is not suitable for application to a roof. 

For application to a plastisol clad roof assuming it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Noxyde Pegarust for brush, roller or spray application.

This is available in a range of colours in a satin finish. 

For 2 coats of 30m² you would require approximately 25ltrs.

These are available to puchase on the website.

Assuming the internal brick walls are clean, dry, sound and prepared as detailed in the technical data sheet with no waterproof sealers applied you could consider Zinsser AllCoat Interior (Solvent-Based).

This is available mixed to many RAL, NCS or BS colours in a matt finish.

Assuming the previously painted garage door and timber door are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser AllCoat Exterior (Water Based).

This can be mixed to many RAL, NCS or BS colours in a matt, satin or gloss finish.

If the timber door is bare it shoudl be primed first with Zinsser Cover Stain.

Thank you for the enquiry, please can you provide more information and pictures to [email protected] and we can look into a recommendation.

What type of stone are the tiles?

What have they been sealed with?

Are they internal or external?

Is there a damp proof membrane present?

What traffic will the floor receive?

Unfortunately we do not have a one coat option for this application, assuming the pvc to be painted is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Zinsser AllCoat Exterior (Water Based) for all areas other than where water can pool such as a roof.

This is available in many RAL, NCS or BS colours in a matt, satin or gloss finish.

Unfortunately we would not recommend to paint sealed limestone floor tiles. 

But if the sealer has worn away and the tiles are now porous, a test on a small area for compatibility and adhesion is undertaken and successful you could consider Coo-Var Acrylic Floor Paint - Special Colours.

This is available mixed to many RAL, NCS or BS colours in a semi-gloss finish.

Assuming you are looking to paint an external building wall with cement based render you could consider Wethertex AP77 Flexible Smooth Masonry Paint - New Colours.

This is available mixed to many RAL, NCS or BS colours in a matt finish.

Regarding patio stones, we would need more information and pictures of the area to be sent to [email protected] to see if we can offer a product for this application.

Assuming the plywood is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Teamac Metaclor Underwater Primer followed by Teamac Chlorvar Chlorinated Rubber Paint.

This can be mixed to many RAL, NCS or BS colours in a gloss finish.

Assuming the previously applied paint along with rust is removed back to bare prepared steel, it is clean, dry, sound we can recommend Teamac High Performance 2 Pack Zinc Phosphate Primer. followed by Coo-Var ProGrip Heavy Duty Two-Pack Anti-Slip Floor Paint for an anti-slip finish. 

This is available in many RAL, NCS or BS colours in an off gloss finish.

To remove the previously applied paint we would recommend blasting or removing with mechanical preparation.

Assuming the concrete steps are previously painted, they are clean, dry, sound, sanded prior to application we can recommend Coo-Var Acrylic Floor Paint - Special Colours.

This can be mixed to many RAL, NCS or BS colours in a semi-gloss finish.

Assuming the timber supporting frame for the decking is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Wethertex OT25 Wood-Flex Satin Opaque Timber Paint. 

This can be mixed to many RAL, NCS or BS colours in a satin finish.

Assuming the granite headstone is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Ardenbrite Quick Drying Base Coat followed by Ardenbrite Metallic Paint then Ardenbrite Protective Glaze.

This is available in a range of colours.

Thank you for the enquiry, please can you provide more information on teh project to [email protected] so we can assist with a recommendation.

We offer Colour Sample Sachets, these are in a generic paint to aid choosing a colour.

Unfortunately we do not have a product we can recommend for this application to rust with a clear finish. 

Thank you for the enquiry, Colour Sample Sachets are available.

Assuming the cement based rendered area of the fire place is not exposed to direct flame contact, if white is chosen Tikkurila Muuri can withstand a dry heat of upto 300°C.

If one of the tinted colours is chosen, this can withstand 180°C.

Assuming the board is a mineral board, it is not exposed to direct flame contact, it is clean, dry, sound and prepared we can recommend Tikkurila Muuri.

This can withstand a dry heat of upto 300°C in white or upto 180°C in a tinted colour.

For the outside of the cast iron guttering assuming they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum CombiColor Original.

This can be mixed to many RAL, NCS or BS colours in a satin or gloss finish.

Any bare metal areas should be primed with Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion.

For the internal surfaces you could consider Rust-Oleum Mathys Fillcoat.

Assuming the aluminium garage door is polyester powdercoated, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Kolorbond Aquatek.

This can be mixed to many RAL, NCS or BS colours in a satin finish.

Please can you provide more information and pictures of which areas of the vessel you are wishing to paint to [email protected] so we can assist with a specification.

Assuming the roof has the corrosion removed, it is clean, dry sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Mathys Noxyde Plus for spray application.

This is available in a range of colours in a satin finish.

This product is designed for waterproofing of flat roofs and gutters, it is not a decorative paint. 

For this application depending on the finish of the render, assuming it is cement based you could consider Rust-Oleum Mathys Murfill Quartz  to address small surface uneveness.

It provides a textured, waterproof surface coating to exterior walls and façades.

This can be overpainted with water based paints.

While we do not have a product to recommend to restore the finish to the door, if you wanted to paint the door you could consider the Kolorbond uPVC Painting Kits.

This can be mixed to many RAL, NCS or BS colours in a satin finish.

For this application assuming the stone is porous, clean, dry, sound and prepared as detailed in the technical data sheet you could consider Tikkurila Muuri.

While we have no experience of it being applied to Cotswold Stone assuming it has some porosity and with this in mind would have thought it would be ok to paint but as ever in these circumstances a small test would probably be advisable first to make sure it adheres ok.

With reference to the heavily stained issue however this does pose a potential problem in as much that the contamination could cause a few issues such as discolouration of the Muuri (bleeding) and potentially may also impair adhesion resulting in flaking and general loss of adhesion if this cannot be removed prior to application.

This paint can withstand upto 300°C in white or upto 180°C in a tinted colour. 

This is not suitable for direct flame contact.

Assuming the stone step is bare, porous, clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Coo-Var Anti-Slip Acrylic Floor Paint.

The first coat should be thinned 5% with clean water. 

This is available in a range of colours in a matt anti-slip finish.

Yes a paint for this area would be a solid colour and it would not be possible to replicate the wood finish exactly if there is more than one colour on the sills.

We do offer a Colour Match Service if you wish to send in a sample.

For painting a composite door we can recommend the Kolorbond uPVC Painting Kits.

This is available in many RAL, NCS or BS colours in a satin finish.

The kit comes with the required preparatory materials and offers a 10year guarantee on adhesion and 5 years on colour fastness.

For painting a composite door we can recommend the Kolorbond uPVC Painting Kits.

This is available in many RAL, NCS or BS colours in a satin finish.

The kit comes with the required preparatory materials and offers a 10 year guarantee on adhesion and 5 years on colour fastness.

Unfortunately we do not have a heat resistant paint we can recommend for this application.

Please can you provide more information on what the floor is made of and if it is bare or previously painted to [email protected] so we can assist.

As this is a fire protection enquiry we will need the information below sending to [email protected] to assist.

GENERAL TIMBER SURFACES

- Size of surface area to paint

- Timber thickness

- Level of Fire Protection required (Class 1, Class 0, 30min, 60min, etc.)

- Type of timber (i.e. pine, mdf, plywood, etc.)

- Type of Timber surface (i.e. T&G, feather edge / shiplap cladding, solid panels / sheets, etc.)

- Internal or external

- Use (i.e. floor, wall cladding, ceiling, etc.)

- Clear or coloured coating required?

- Bare or previously coated?

For MDF cabinets you could consider HMG Pre Cat Primefast 2014-04 followed by HMG Acid Cat MB Colours.