Assuming the door is clean, dry, sound, lightly abraded and prepared as detailed in the techncial datasheet, this product can be applied directly to fibreglass doors as a recommended 2 coat application.

For increased adhesion and protection, you could prime first with Zinsser Bulls Eye 1-2-3 prior to application.

Assuming application is to a timber door, the door is clean, dry, sound, lightly abraded and prepared as detailed in the technical datasheet, you could consider a first coat of Zinsser Cover Stain to any bare areas of timber, before 2 full coats of Zinsser Allcoat Exterior Satin Water-Based to finish.

We'd recommend applying to a small test area to begin, to check for compatibility and adhesion with the existing coating prior to full application.

Assuming the shipping container is clean, dry, sound and prepared as detailed in the technical, this product can be used.

However, priming with Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion would be recommended, this will provide increased protection against Anti-Corrosion, before finishing with 2 full coats of Zinsser Allcoat Exterior Satin in your choice of many RAL, BS & NCS Colours.

For greater protection, you could also consider Rust-Oleum 7500 Alkythane as an alternative. 

Assuming the Zinsser Allcoat Exterior Satin Water-Based is fully cured, it is lightly abraded, it is clean, dry, sound, this product can be over-painted.

We would recommmend to test on a small area for compatibility and adhesion prior to full application.

Assuming the silicone render (K Rend) is clean, dry, sound and prepared as detailed in the technical datasheet, this product in either a Satin or Matt Water-Based finish could be an option.

2 full coats are recommended, in your choice of many mixed colours.

Assuming the fibreglass substrate is clean, dry, sound, lightly abraded and prepared as detailed in the technical datasheet, providing there is a vertical water run-off and the product isn't being applied to a roof, this should be fine for application.

2 coats are recommended to achieve the desired outcome, with a choice of 4400+ RAL, BS & NCS Colours available.

To ensure the surface is prepared sufficiently, you could consider Zinsser Universal Degreaser & Cleaner to remove all traces of oils, grease, and surface contaminants to provide a clean substrate prior to painting.

Assuming application is for kitchen glazed wall tiles, that are clean, dry, sound and prepared as detailed in the technical datasheet, we'd recommend a first coat of Zinsser Bulls Eye 1-2-3 to prime the tiles, providing improved adhesion to the tiles.

To finish, two full coats of Zinsser AllCoat Exterior Satin Water-Based, in your choice of many RAL, BS & NCS Colours, can then be applied to provide a decorative topcoat finish.

In preparation, Zinsser Universal Degreaser & Cleaner should be applied to the tiles, ensuring they are thoroughly clean and free of all oils, grease and surface contaminants prior to painting.

Assuming the composite door is clean, dry, sound and prepared as detailed in the technical datasheet, Zinsser AllCoat Exterior Water-Based, in your choice of Satin, Matt or Gloss finish, will be fine for application.

It is recommended to apply 2 full coats to achieve the intended finish, and can be mixed to many RAL, BS or NCS Colours.

Thank you for your enquiry, please e-mail [email protected] with further details of your requirements, in particular if the plastic is in direct contact with shower/bath water.

Assuming the concrete is clean, dry, sound and prepared as detailed in the technical, is porous and isn't being applied to a floor, Zinsser AllCoat Exterior Satin (Water-Based) will be fine for application to the concrete.

With regards to the corrugated steel, please e-mail [email protected] with further application requirements on the type of corrugated steel.

Assuming the putty is clean, dry, sound and free from any surface contaminants prior to application, we'd recommend a first coat of Zinsser Cover Stain to prime, seal and stain block the putty, before 2 full coats of Zinsser AllCoat Exterior in your choice of RAL, BS or NCS Colours as a decorative finish.

Thank you for your enquiry, we have replied directly to your e-mail sent into the technical sales inbox for this enquiry. 

Assuming the steel railings are clean, dry, sound and prepared as detailed in the technical datasheet, any loose and flaking material is removed, bare metal areas are spot primed with Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion, this product could be used.

All areas of the railings to be paint must be cleaned and sanded prior to application.

Assuming the garage door is polyester powdercoated, it is bare, clean, dry, sound and prepared as detailed in the technical data sheet this product can be applied.

We would recommend to test on a small area for compatibility and adhesion prior to full application. 

Assuming the solid wood cabinets contain no wood oils/wax previously coated into the timber, and prepared and abraded as detailed in the technical datasheet, we'd recommend Priming firstly with a coat of Zinsser Cover Stain, which will seal the timber, before 2 full coats of Zinsser Allcoat Exterior Satin mixed to your choice of 4400+ RAL, BS or NCS Colours.

Unfortunately we would not recommend this product for this application.

But assuming the marble is not exposed to foot traffic, direct flame contact or temperatures over 60°C, it is internal, bare, clean, dry, sound and prepared as detailed in the technical data sheet you could consider the option below:

One coat of Zinsser Bulls Eye 1-2-3 followed by two coats of Zinsser Perma-White Interior.

This can be mixed to many RAL, NCS or BS colours in a matt or satin finish.

Assuming these are bare ceramic wall tiles, that are clean, dry, sound and prepared as detailed in the technical data sheet, you could use Zinsser Perma White Interior.

The tiles should be cleaned with Zinsser Mould Killer Remover.

We'd then recommend applying one coat of Zinsser Bulls Eye 1-2-3 to increase adhesion on the tiles, followed by 2 coats of Zinsser Perma-White Interior in your choice of Satin or Matt finish, this can be mixed to many RAL, BS or NCS Colours.

This would not be suitable for areas subject to direct water contact or elevated temperatures.

This product is not recommended for HVLP spray application, it can be airless sprayed and can be thinned to a maximum of 10% with clean water.

No, this paint is suitable for this application without being over coated.

But once fully cured if you wish to you could consider an anti-graffiti clear coating such as Hydron Nu-Guard AG.

Assuming the gloss kitchen cupboard doors are a laminate, they are clean, dry, sound and prepared as detailed in the technical data sheet we would recommend they are first primed with Zinsser Bulls Eye 1-2-3 prior to application.

This paint can be thinned with clean water to a maximum of 10%.

This paint can be applied by brush, roller or airless spray only.

Yes, assuming the timber window frames are clean, dry, sound and prepared as detailed in the technical data sheet this paint can be used.

Any bare timber areas should be primed first with Zinsser Cover Stain.

This product can be applied directly to clean, dry, sound and prepared PVC, for other plastics we would recommend testing for compatibility and adhesion prior to full application.

Unfortunately the manufacturer does not produce sample cards as these paints are mixed toindustry standard RAL, NCS or BS colours.

We would recommend viewing these in physical colour charts in person, not choosing a colour from a screen.

These can be found at local trade paint suppliers, our trade counter in Leeds.

Yes we mix these paints on an automated mixing machine.

We would recommend a medium pile Roller Sleeve.

Providing the vinyl wrap is soundly adhered to the cupboards Zinsser AllCoat Exterior (Waterbased) will be perfect for this application. 

There’s no need to prime but we recommend giving the surface a good clean down using hot soapy water, rinsing with warm water then wiping over with Methylated Spirit. 

No, unfortunately we cannot recommend this product for kitchen worktops.

Assuming the kitchen worktops are a laminate, they are clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Rust-Oleum Worktop Transformation Kit.

This is available in galaxy black or diamond white.

This paint is available in a matt, satin or gloss finish, if you are concerned about glare we would suggest either matt or a satin finish.

If the timber is bare we would recommend application of Zinsser Cover Stain to the prepared area prior to application.

We would suggest cleaning with Zinsser Universal Degreaser & Cleaner and then priming with 2 coats of Zinsser Bulls Eye 1-2-3 Plus. Then you could apply Zinsser AllCoat Exterior Satin (Water Based) in the colour of your choice.

The manufacturer has not tested this product for application onto lining paper.

Assuming the lining paper is clean, dry, sound and prepared as detailed in the technical data sheet we would recommend Zinsser Perma-White Interior.

This can be mixed to many RAL, BS or NCS colours in a matt or satin finish.

Yes assuming the mould is removed, the previously painted walls are clean, dry, sound and prepared as detailed in the technical data sheet this can be used.

We would recommend testing on a small area prior to full application for compatibility and adhesion with the previously applied paint.

Yes this paint will be suitable, the fibreglass garage door must be clean, dry, sound and prepared as detailed in the technical data sheet and primed first with Zinsser Bulls Eye 1-2-3.

This can be mixed to many RAL, BS and NCS colours.

Unfortunately no, we cannot recommend this for application to EPDM. 

Assuming the EPDM is on a roof, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend GacoPro Roof Coating for this application.

For application this time of year with temperatures below 10°C we would recommend the Zinsser Allcoat Exterior Satin Solvent Based.

Assuming the wooden fascias are bare, clean, dry, sound and prepared as detailed in the technical data sheet we would recommend priming first with Zinsser Cover Stain.

This paint has a coverage rate of 12m² per litre per coat, we would recommend a two coat application with an additional coat to areas subject to pooling water such as sills.

On bare timber we would recommend the timber be primed initially with Zinsser Cover Stain prior to application of Zinsser Allcoat Exterior Satin Water Based. 

Please be aware when painting glass brush strokes will be visible through the glass. Assuming the glass is clean, dry, sound and prepared as detailed in the technical data sheet, the glass should be primed first with Zinsser Bulls Eye 1-2-3 prior to application.

We would recommend using a primer and topcoat assuming visible brush strokes are acceptable.

Assuming the wooden fence is clean, dry, sound and prepared as detailed in the technical data sheet yes it can be used.

We would recommend priming all bare timber first with Zinsser Cover Stain prior to application.

Assuming you are looking to paint the internal faces of the polycarbonate we would recommend testing for compatibility and adhesion prior to full application as Zinsser Allcoat Exterior Water based will not adhere to all types of polycarbonate.

It should be degreased with Zinsser Universal Degreaser & Cleaner and prepared as detailed in the technical data sheet.

If you are looking to paint the external face of the polycarbonate, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Britannia Aquashield Eco.

Please be aware that brush strokes will be visible through the panels.

Assuming the asbestos pipe is clean, dry, sound and prepared as detailed in the technical data sheet yes.

The pipe should be primed first with Zinsser Bulls Eye 1-2-3.

No, please check the Technical Data Sheet for the wood preserver, this states it can only be over painted with suitable solvent based options.

Zinsser Allcoat Exterior Solvent Based may be suitable, but we would recommend testing for compatibilty and adhesion prior to full application.

Assuming this wooden rail is not being walked on, it is clean, dry, sound and prepared as detailed in the this paint could be used.

We would recommend priming first with Zinsser Cover Stain and testing for compatibility/adhesion to the previously stained timber and the filler.

Assuming the timber is bare, clean, dry, sound and prepared as detailed in the technical data sheet it will need priming prior to application.

We would recommend spot priming knots with Zinsser B-I-N then prime the bare timber with Zinsser Cover Stain.

Assuming the powder coating is clean, dry, sound and prepared as detailed in the Technical Data Sheet we would recommend priming first with Zinsser Bulls Eye 1-2-3 prior to application.

This is a long lasting paint suitable for internal or external application with upto 15 years performance.

Assuming the substrates are clean, dry, sound and prepared as detailed in the Technical Data sheet this will be suitable for application to external timber cladding.

Any areas of bare timber should be primed prior to application with Zinsser Cover Stain.

The manufacturer does not produce colour charts for this product.

It can be mixed to many RAL and BS colours in a matt, satin or gloss finish.

Assuming the aged UPVC is clean, dry and abraded prior to application we can recommend Zinsser Allcoat Exterior Waterbased. This can be applied by brush roller or airless spray only.

This can be thinned if absolutely necessary (10% max with water).

Usually it would need to be thinned more in order for it to pass through a HVLP, which is why we do not recommend it.

Assuming the previously painted steel door is clean, dry and abraded Zinsser Allcoat Exterior Waterbased can be applied directly. If any areas are back to bare steel we can recommend priming with Bulls Eye 1-2-3. Zinsser Allcoat is available in many RAL and BS colours, please see the colour chart on the product page so you can find an appropriate match.

Assuming the door is clean, dry and sound we can recommend the use of Zinsser Bulls Eye 1-2-3, this is a compatible water based primer.

Zinsser AllCoat Exterior Satin (Water Based) can go directly onto degreased galvanised steel with no primer coat required.

Assuming the door is dry, sound and prepared as you stated above we can recommend the waterbased option for this application at this time of year.

At temperatures down to approximately 5°C we recomend the solvent based option.

Assuming the UPVC is aged, clean, dry and sound this product would be perfect for this application.

This paint does not require thinning for use with an airless sprayer and can also be applied with a brush or roller.

 Zinsser Allcoat Exterior Satin WB has not been specifically tested for use on composite doors but we do recommend it use on suitably prepared uPVC.

Assuming they are clean, dry and free from anything to effect adhesion yes it can.

Zinsser Allcoat Exterior Satin (Water Based) is self priming on aged, clean uPVC and does not require an undercoat.

We do not have sample pots the smallest quantity available is a 1ltr tin.

Providing you are looking to apply the AllCoat Exterior Satin Water Based to galvanised steel, then two coats may be applied by brush or roller at a coverage rate of approximately 10m2/litre/coat directly onto the bare surface. If this is ferrous steel, then a red oxide or zinc phosphate primer will need to be applied prior to using the AllCoat Exterior Satin. The paint should be applied when the air and substrate temperature is 10°C and rising, relative humidity less than 80%. Ensure there is no risk or rain, fog, frost or condensation from affecting the applied paint before it has had a chance to fully cure.

We recommend to ensure the surface to be painted is clean, dry, sound and free from any surface contamination such as dirt, oils, grease, mould, mildew, rust, loose or flaking paint etc that are likely to affect the performance of any subsequent coats of paint; to ensure this we advise the following prior to painting, clean down with hot soapy water, rinse with warm water and when dry have a good wipe over with methylated spirits to promote good adhesion.

Zinsser Allcoat Exterior Sain (Water Based) can be applied directly to weathered uPVC once it is clean and dry. You can give the uPVC a light abrasion if you wish but it is not usually required.

Yes this product can be used for interior projects and surfaces also. We are able to match many colours so if you cannot find a colour to your liking on our website, please call our Technical Team on 0113 2455450 (option 2) who will be able to help with colour matches for you.

Zinsser AllCoat Exterior Satin (Water Based) can go directly onto degreased galvanised steel with no primer coat required.

Yes, however we would recommend first priming the bare plywood with Zinsser Cover Stain.

Yes Zinsser AllCoat Exterior Satin (Water Based) could be used for this, if you require a primer/undercoat we would suggest Zinsser Cover Stain.

Yes, exterior surfaces which have been weathered can be washed down using warm water and dilute detergent followed by rinsing off with clean water and then 2 coats AllCoat Exterior Satin (Water Based).

No. If you contact our Technical Team on 0113 2455450 (option 2) or [email protected] they should be able to advise a suitable alternative after asking some further details on your tiles and requirements.

The Zinsser Allcoat Exterior products should not be thinned for application, they can be applied by brush, roller or airless spray but not HVLP as this would require too much thinning which will have an adverse effect on the performance of the product.

Yes, Zinsser AllCoat Exterior Satin (Water Based) is fine to use internally and is fine for brick surfaces.

Yes this would be fine.

Normally we would recommend Zinsser Cover Stain to prime linseed oil putty, it should also be fine over the acrylic putty however both should be allowed to dry sufficiently before painting.

Zinsser AllCoat Exterior Satin (Water Based) will not bond to silicone, this would need to be removed, the surface then cleaned to remove traces of silicone. Zinsser AllCoat Exterior Satin (Water Based) will take to the previously painted fascia. The gaps can be resealed after painting with a suitable sealant.

On any areas of bare timber/filler we would first recommend priming with Zinsser Cover Stain.

MDF should be primed with 1 coat of Zinsser Bulls Eye 1-2-3 followed by 2 coats of either Zinsser Allcoat Exterior Satin (Water Based) or Zinsser Perma-White Interior. The surface should be free of any contaminant prior to application.

Yes.

Yes, all of the Zinsser AllCoat Exterior (Water Based) products can be used internally. You still need to prime certain substrates as indicated on the tech data sheet, hardwoods, stained areas, etc. Please note Zinsser AllCoat Exterior (Solvent Based) products cannot be used for interior projects.

Assuming this is not a floor surface, if interior woodwork prime with Zinsser B-I-N first to get a good key. If exterior prime with Zinsser Cover Stain. Surfaces must be clean and sound before priming.

We would recommend Zinsser AllCoat Exterior (Water Based) for this. The Satin and Gloss versions are self priming onto this type of surface, apply 2-3 coats directly, no need for a primer. If the Matt finish is required, first prime with Zinsser Bulls Eye 1-2-3.

We would instead recommend Rust-Oleum 3302 CombiPrimer Adhesion followed by Rust-Oleum CombiColor for this application.

Zinsser AllCoat Exterior Satin (Water Based) can be applied directly to GRP or previously painted surfaces after abrading the surfaces with a fine grade of sandpaper followed by a solvent wipe using methylated spirits for GRP or suitable detergent/cleaner degreaser for previously painted surfaces. Then apply 2 coats of the AllCoat Exterior Satin (Water Based).

Zinsser AllCoat Exterior Satin can be applied directly to UPVC with no primer required. We would advise abrading the surfaces with a fine grade of sandpaper followed by a solvent wipe using methylated spirits. Then apply 2 coats of the AllCoat Exterior Satin.

We would recommend checking with Cuprinol to make sure the Ducks Back product can be overpainted, if it has weathered for 3 years it may be OK but some of these types of products contain waxes which will affect adhesion of subsequent paint coatings. Provided there is minimal wax content then Zinsser AllCoat Exterior Satin (Water Based) can be used.

Zinsser AllCoat Exterior Satin (Solvent Based) can be applied directly to plywood and can be used at lower temperatures. If you want to use Zinsser AllCoat Exterior Satin you will have to wait for warmer weather and first prime the plywood with Zinsser Cover Stain.

Zinsser AllCoat Exterior Satin will be OK for this, however as we are heading towards cooler weather however it may be advisable to go for the Solvent Grade. Drying conditions will be poorer at this time of year which will affect the drying of the water based AllCoat. This is likely to cause issues if the coating gets caught in a shower of rain before it has fully cured. The AllCoat can go on directly without sanding or priming provided the surface is clean, existing coating is sound etc.
2 coats should be sufficient provided the colour of the Sandtex Gloss and the sage green you require is similar.

We would recommend priming first with Zinsser Cover Stain.

Yes, the Water Based Zinsser AllCoat Exterior Satin or Gloss should go over an aluminium wood primer without issue.

Zinsser AllCoat Exterior Satin is not suitable for floor surfaces, we would instead recommend Smartkote Protectakote UVR for this application.

Yes, although we do recommend priming bare, exterior timber first with Zinsser Cover Stain.

Zinsser AllCoat Exterior Satin can be applied directly to UPVC with no primer required. We would advise abrading the surfaces with a fine grade of sandpaper followed by a solvent wipe using methylated spirits. Then apply 2 coats of the AllCoat Exterior Satin.

The Zinsser AllCoat Exterior water based range would be ideal for this application. We normally recommend a coat of Zinsser Cover Stain is applied first to block any staining and existing colours.

No. Instead, prime with Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion followed by Rust-Oleum CombiColor.

It could but for interior work on wood we'd recommend Zinsser Perma-White Interior instead.

Zinsser AllCoat Exterior Satin can be applied directly to UPVC with no primer required. We would advise abrading the surfaces with a fine grade of sandpaper followed by a solvent wipe using methylated spirits. Then apply 2 coats of the AllCoat Exterior Satin.

I'm afraid not, you can see our range of decking paints here: Decking Paints.

Yes this product can be applied directly to powdercoat surfaces, clean and lightly sand to provide a key before application.

Any areas of rust should be prepared and primed first with something like Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion.

Zinsser AllCoat Exterior Satin can be applied directly over existing paints after cleaning and light sanding. Apply two coats, no primer is required. If there are any areas of bare lead after preparation, prime first with a coat of Zinsser Bulls Eye 1-2-3 and the apply 2 coats of Zinsser AllCoat Exterior.

Zinsser AllCoat Exterior Satin is self-priming and will adhere to any sound surface. The first coat of Zinsser AllCoat Exterior Satin primes and seals the surface, providing a base for the second coat. The second and third coats (if required) complete the sealing process while providing additional moisture resistance and protection. Before painting, fill all nail holes and gouges with a proprietary filler. Where necessary, spot prime knots and sap streaks with Zinsser B-I-N. For new or unpainted cedar, redwood, or other resinous timbers prime with Zinsser Cover Stain.

According to the manufacturer Medite, they recommend water based paints are suitable for this substrate so on that basis Zinsser AllCoat Exterior should be fine to use.

No, we would recommend treating any knots with Blackfriar Patent Knotting followed by 1 coat of Blackfriar Aluminium Wood Primer over all areas to be painted. Once dry finish with 2 coats of Zinsser AllCoat Exterior Satin in your chosen colour.

No it won't. We would recommend priming the stainless steel with Rust-Oleum 3302 CombiPrimer Adhesion and then applying two coats of Rust-Oleum CombiColor in your desired colour and finish.

Yes it is, where necessary, spot prime any knots and sap streaks with Zinsser B-I-N Primer Sealer. After 45mins you can then start to apply the Zinsser AllCoat Exterior Satin as requried.