Is this product non flammable

Unfortunately no, this is a solvent based paint.

I have a steel fire escape that requires anti-slip paint for the landings and treads as part of its ongoing maintenance. Due to the location of the fire escape we have found that the upper levels are exposed to direct sunlight most of the year which has warn away all the existing slip-resitant finishes over time. The lower levels are constantly in shade and, as such, are fairly damp. The existing slip-resistant finishes are now coming off in large sections and appear to have been permitted vegetation growth. Would this product be suitable for prolonged exposure to direct sunlight as well as being in a prolonged damp environment? In addition, what kind of life expectancy could be expected?

This product is UV stable and is suitable for internal or external use. Assuming the staircase is clean, dry, sound and prepared correctly this could last many years on a fire escape, this will be determind though by the level of traffic and exposure. Any bare metal should be primed first with Coo-Var Water Based All Metals Primer

Hi - I'm looking for paint/treatment to protect the wood floor around an indoor hot tub as it would get wet with splashes. Would be helpful if it was also not too slipperly though I also plan to put non-slip mats on top in certain areas. Was looking at Teamac Metaclor Antifouling Primer followed by Teamac Chlorvar Chlorinated Rubber but didn't know if that would be overkill and/or slippery? Any suggestions? Thanks!

Assuming the timber floor is clean, dry, sound and prepared as detailed in the Technical data sheet we can recommend Smartkote Safekote. The first coat should be diluted 10% with 100 Rapid Drying Thinner . This is a barefoot friendly antislip paint available in a range of colours and a clear option.

How Mitch paint will I need to do a floor 40 m2

5 litres would be sufficient to apply 1 coat to 40m² - so 2 x 5 litres to apply the required 2 coats plus any primer if required.

Can I use this on galvanised steel fire escape stairs please

Yes, first prime bare galvanised steel after preparation as per the product data sheet with Coo-Var Water Based All Metals Primer .

I am looking to use your light Grey 501 anti slip floor paint onto brand new self levelling latex, will this make it waterproof ? and does it need a primer or etch ? or would a thinned pre coat be fine ?

Providing the self leveller you have used can be painted with solvent based coatings then you would apply a primer coat of 301 Industrial Floor Paint diluted 10% with white spirit followed by 2 coats of 501 Anti Slip Floor Paint . This will provide a durable anti slip finish but is not deemed waterproof

Aluminum painting Hi, I am interested in your anti slip paint, I am needing to coat some aluminium checker plate. If i etch prime then paint will that be suitable?? Regards Andy

To apply an anti-slip coating to aluminium we would usually suggest Smartkote Protectakote 2K Metal Primer followed by Smartkote Protectakote UVR .

We are a scout district in north Norfolk and need to paint new woodwork on our mobile climbing tower ,with some sort of textured paint that will allow Shoes to grip to some extent what is best product to use please

501 Anti-Slip Floor Paint should be ideal for this application, on new wood we recommend Coo-Var Penetrating Wood Primer be applied first.

Hi I have a sloping drive which becomes very slippery when wet. It appears to be a painted concrete surface. Would your 501 anti slip paint be suitable for this.

Potentially, but as we don't know what the drive is currently painted in you will have to carry out a test area prior to full application to ensure adhesion/compatibility. After cleaning and preparation as per the product data sheets, apply 1 coat of 301 Industrial Floor Paint thinned 10% with white spirit. Allow to dry overnight, then apply 2 coats of 501 Anti Slip Floor Paint allowing at least 16 hours between coats.

Hello, Just finished my Narrowboat roof in the Blue 501 Anti Slip Floor Paint. Really happy with it, but would like to detail some areas on the boat in the same colour without the aggregate. Could you supply this?

Yes, the nearest colour to our 501 Anti Slip Floor Paint in Blue is BS 18D43. This colour can be produced in something like Teamac Marine Gloss or Rust-Oleum CombiColor .

Hi,do you have a non slip paint for floor tiles? Thank you,regards Jackie

Smartkote Safekote can be applied to glazed tiles after the application of Smartkote Protectakote Clear Primer Treatment , see product information and data sheets for full details.

Do you have a non slip paint suitable for an aluminium van ramp, used for wheeled flight cases?

We would recommend Smartkote Protectakote UVR for this. Abrade to fresh metal, clean well using detergent. Prime with Smartkote Protectakote 2K Metal Primer as per instructions within 30 minutes. Then apply Smartkote Protectakote UVR as per instructions, you may also be interested in Smartkote Protectakote UVR Accelerator and Smartkote Protectakote Safety Grip to be used in conjunction with your application.

I want to put a non slip path on my block paved driveway using 501 anti slip floor paint. I have jetwashed the area I want to paint. Can I paint direct to this cleaned surface OR is there other preparatory work I need to do first?

After cleaning a priming coat of 301 Industrial Floor Paint thinned 10% with White Spirit should be used before application of 501 Anti Slip Floor Paint.

Can you tell me what primer do I need to order and is used on clean concrete when painting with 501 anti slip paint. Regards D Pontefract

On suitably prepared bare concrete a priming coat of 301 Industrial Floor Paint thinned 10% with White Spirits should be used before application of 501 Anti Slip Floor Paint.

Is there a primer needed on bare timber boards before applying the 501 anti slip floor paint

Yes - 407 Multi Surface Primer .

Is Anti slip paint 501 suitable for an external meta staircase and can it be applied over a previous coat of anti slip paint?

It is suitable for use on external metal staircases. Any bare metal areas should be prepared and primed with a suitable primer. Existing paint should be well adhered, clean and abraded to provide a key if necessary before application of 501 Anti Slip Floor Paint directly to the surface.

Hi, I am looking for a paint adhere to an aluminium truck bed for driving vehicles onto . Is your 501 antislip paint suitable? Thank you Steve

We would recommend priming the aluminium with 707 MMA Metal Primer and finishing with 703 MMA Flexible Anti-Slip Coating .

hi can you let me know is it ok to mop over this paint with out it coming off. thanks phu

Mopping this product certainly won't remove it as it is a durable coating that can also be used externally but it does have a very rough texture to the finished surface which will make it nearly impossible to mop. If you require an anti-slip coating you can clean for internal areas, we would recommend 503 Easy Clean Anti Slip Coating .

501 Anti Slip Floor Paint

Reference RAW501

Brand Rawlins Paints

Search ID RAW1103

Rawlins' leading ready-mixed interior/exterior use anti-slip floor coating for suitably primed concrete, wood, metal and GRP.

For foot, light truck and occasional heavy truck use
Touch dry in 6 hours @ 20°C
Ideal for boats, steps and stairways, disabled ramps, doorways, machinery areas, most floors and other areas where moisture and other substances may cause the floor to be slippery

Colour

Pick a Colour

Current colour: Grey

White
White
Black
Black
Light Grey
Light Grey
Blue
Blue
Green
Green
Grey
Grey
Red
Red
Yellow
Yellow

Size

£75.08(incl. VAT)

£62.57(ex. VAT)

Quantity

Please choose your colour

In Stock and Available for Delivery (See Delivery Options Below)

ColourPicker Explained

In general we sort colours for products into 2 main groups - ‘Ready Mixed’ and ‘Tinted’.
Tinted colours will always be more expensive than Ready Mixed colours as they need to be produced at the time of order using a tinting machine dispensing colourant into a base*.
During busy periods, this means that tinted colours could take longer, for example – a ready mixed colour ordered on a 3-5 day delivery might arrive within 3 days, however a tinted colour might take the full 5 days to arrive.

To find Ready Mixed colours, search "ready mixed" or select the Ready Mixed 'colour chart'. To see Tinted colours select a colour chart such as RAL, BS, NCS, etc. or search for a colour/hue to see available or related options.

To ensure fair pricing, we split colours into ‘Price Bands’ to group together similar priced colours. If you wish to search for the cheapest tinted colours, always select Price Band 1.

We make every effort to list all available colours, however we also offer a colour match service which can be accessed by contacting our Technical Team on 0113 245 5450 (option 2) or emailing [email protected]

*Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour

Colour reproduction of the Products on the Site is limited by the technology used to deliver web pages and by the colour representation of Customer’s own monitor and computer set-up. We have made every effort to display as accurately as possible the colours of our Products but we cannot guarantee that the colour shown on Customer’s monitor’s display will accurately reflect the colour of the Product on delivery. We recommend that Customer first purchases the smallest Product available or access an industry standard colour chart in person (and not digitally) to ensure that the colour is acceptable for its purposes.

18 questions about the product

Description

501 Anti Slip Floor Paint is a ready-mixed floor coating for suitably primed concrete, wood, metal and GRP which provides a rough, anti-slip finish when dry. It provides durability, decoration and protection. Suitable for indoor and outdoor use

Ideal for boats, steps and stairways, disabled ramps, doorways, machinery areas, most floors and other areas where moisture and other substances may cause the floor to be slippery.

For foot, light truck and occasional heavy truck use.

Features & Benefits

Ready mixed
For internal and external use
For suitably primed concrete, wood, metal and GRP
Provides a rough, anti-slip finish when dry
Ideal for boats, steps and stairways, disabled ramps, doorways, machinery areas, most floors
For foot, light truck and occasional heavy truck use
Touch dry in 6 hours @ 20 °C
Application by brush or roller

Typical Properties

Technical Data
	501 Anti Slip Floor Paint
Specific Gravity:	1.35 - 1.55 @ 20 °C
Volume Solids:	60%
Wet Film Thickness:	100 - 150 microns
Dry Film Thickness:	60 - 100 microns
Typical Viscosity:	6.5 Poise @ 25 °C
Flash Point:	Above 32°C (closed cup)
V.O.C.	343g/litre

Coverage

Expected spreading rate of 6-10m²/litre, achieving an overall dry film thickness of 60-100 microns (based on brush application)

Surface Preparation

All surfaces should be clean, dry, sound and free from contaminants
Concrete - power floated, granolithic and smooth surfaces should be roughened first to provide a good "key" for the paint
This can be done mechanically by abrading or blasting, or chemically using Acid Etch
These processes will have the advantage in addition to preparing the surface of also removing dirt and laitance
New concrete must be allowed to cure thoroughly which can take up to 3 months
Apply a 10% thinned coat of 301 Industrial Floor Paint to prime and seal the surface prior to applying Anti-slip Floor Paint
Other surfaces must be prepared and primed with the suitable primer for that substrate
Existing painted surfaces - Surfaces should be cleaned, degreased and sanded to ensure an adequate "key" is produced
Remove all loose and flaking material and treat bare areas as new substrate and prepare accordingly

Mixing:

Stir well before use
Do not use a mechanical shaker

Priming:

Suitable wood primer on wood, zinc phosphate metal primer on ferrous metals, 10% thinned 301 Industrial Floor Paint or Multi Surface Primer on concrete

Application

As dictated by normal good painting practice
In confined spaces, provide adequate ventilation during application and drying

Cleaning

White Spirit

Curing

Drying Times
	501 Anti Slip Floor Paint
Touch Dry:	6 hours @ 20 °C
Hard Dry:	24 hours @ 20 °C
Full Hardness:	5-7 Days @ 20 °C
Minimum Overcoating Time:	16 hours/Overnight Dry

Low temperature and high humidity will adversely affect application, drying and performance of any coating.

Storage & Shelf Life

Store only in the original container
Keep container tightly closed and upright, in a cool, well ventilated place
See section 7.2 of the Safety Data Sheet for further information

Health & Safety

Please refer to Material Safety Data Sheet for information
501 Anti Slip Floor Paint shall be applied strictly in accordance with the manufacturer’s instructions

For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]

Product Details

Reference 1103-310027

Data sheet

For Use By: Consumer Use
Interior / Exterior Use: Interior & Exterior
For Use On: Concrete, Wood, Metal, GRP
Colour: Standard / Ready Mixed
Single, Two or Three Pack: Single
Base Type: Solvent
Dry to Recoat (at 20°C): 16 hours/Overnight Dry
Fully Cured (at 20°C): 5-7 Days
Coverage: 6 - 10m² per litre
Solids by Volume: 60%
VOC: 343g/litre
Touch Dry: 6 Hours
Recommended Dry Film Thickness: 60 - 100 microns
Recommended Wet Film Thickness: 100 - 150 microns
UN Number: UN1263
Specific Gravity: 1.35 - 1.55 @ 20 °C
Viscosity: 6.5 Poise @ 25 °C
Hard Dry: 24 hours @ 20 °C
Base Type: Solvent-Based
Suitable For Use On: Boats
Suitable For Use On: Stairways
Suitable For Use On: Machinery Areas
Suitable For Use On: Disabled Ramps
Suitable For Use On: Doorways
Suitable For Use On: Workshops
Suitable For Use On: Timber
Suitable For Use On: Metal
Suitable For Use On: Concrete
Suitable For Use On: Wood
Suitable For Use On: GRP Glass-Reinforced Plastic
Suitable For Use On: Coated Surfaces
Suitable For Use On: Stairs
Suitable For Use On: Steps
Suitable For Use On: Ramps
Application Method: Brush
Application Method: Roller
Components: 1K
Usages: Anti-Slip
Product Usage Type: Topcoat
Fastest Delivery: Next Working Day
Product Category: Paints
Colour Family: Red
Colour Family: Yellow
Colour Family: Black
Colour Family: White
Colour Family: Grey
Colour Family: Green
Colour Family: Blue
Anti-Slip Texture: Coarse Texture

Attachments

Download

Product Data Sheet

Download

Safety Data Sheet

Download

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

Name ^*

Email ^*

Question ^*

^* Required fields

I have read and agree to the conditions of use (read)

Alan Parsons on 2023-06-28 20:39:21	Question: Is this product non flammable
	Answer from Rawlins’ Technical Team: Unfortunately no, this is a solvent based paint.

Andrew Milner on 2022-07-27 09:35:55	Question: I have a steel fire escape that requires anti-slip paint for the landings and treads as part of its ongoing maintenance. Due to the location of the fire escape we have found that the upper levels are exposed to direct sunlight most of the year which has warn away all the existing slip-resitant finishes over time. The lower levels are constantly in shade and, as such, are fairly damp. The existing slip-resistant finishes are now coming off in large sections and appear to have been permitted vegetation growth. Would this product be suitable for prolonged exposure to direct sunlight as well as being in a prolonged damp environment? In addition, what kind of life expectancy could be expected?
	Answer from Rawlins’ Technical Team: This product is UV stable and is suitable for internal or external use. Assuming the staircase is clean, dry, sound and prepared correctly this could last many years on a fire escape, this will be determind though by the level of traffic and exposure. Any bare metal should be primed first with Coo-Var Water Based All Metals Primer

Jeet on 2021-05-29 12:47:10	Question: Hi - I'm looking for paint/treatment to protect the wood floor around an indoor hot tub as it would get wet with splashes. Would be helpful if it was also not too slipperly though I also plan to put non-slip mats on top in certain areas. Was looking at Teamac Metaclor Antifouling Primer followed by Teamac Chlorvar Chlorinated Rubber but didn't know if that would be overkill and/or slippery? Any suggestions? Thanks!
	Answer from Rawlins’ Technical Team: Assuming the timber floor is clean, dry, sound and prepared as detailed in the Technical data sheet we can recommend Smartkote Safekote. The first coat should be diluted 10% with 100 Rapid Drying Thinner. This is a barefoot friendly antislip paint available in a range of colours and a clear option.

Adrian on 2019-08-14 20:05:21	Question: How Mitch paint will I need to do a floor 40 m2
	Answer from Rawlins’ Technical Team: 5 litres would be sufficient to apply 1 coat to 40m² - so 2 x 5 litres to apply the required 2 coats plus any primer if required.

Lyn Manning on 2019-07-31 16:15:10	Question: Can I use this on galvanised steel fire escape stairs please
	Answer from Rawlins’ Technical Team: Yes, first prime bare galvanised steel after preparation as per the product data sheet with Coo-Var Water Based All Metals Primer.

Lee Beecham on 2019-04-04 20:12:31	Question: I am looking to use your light Grey 501 anti slip floor paint onto brand new self levelling latex, will this make it waterproof ? and does it need a primer or etch ? or would a thinned pre coat be fine ?
	Answer from Rawlins’ Technical Team: Providing the self leveller you have used can be painted with solvent based coatings then you would apply a primer coat of 301 Industrial Floor Paint diluted 10% with white spirit followed by 2 coats of 501 Anti Slip Floor Paint. This will provide a durable anti slip finish but is not deemed waterproof

Andrew Crichton on 2019-03-05 09:00:48	Question: Aluminum painting Hi, I am interested in your anti slip paint, I am needing to coat some aluminium checker plate. If i etch prime then paint will that be suitable?? Regards Andy
	Answer from Rawlins’ Technical Team: To apply an anti-slip coating to aluminium we would usually suggest Smartkote Protectakote 2K Metal Primer followed by Smartkote Protectakote UVR.

Martin on 2019-01-20 09:29:35	Question: We are a scout district in north Norfolk and need to paint new woodwork on our mobile climbing tower ,with some sort of textured paint that will allow Shoes to grip to some extent what is best product to use please
	Answer from Rawlins’ Technical Team: 501 Anti-Slip Floor Paint should be ideal for this application, on new wood we recommend Coo-Var Penetrating Wood Primer be applied first.

Carol norris on 2018-08-13 15:31:03	Question: Hi I have a sloping drive which becomes very slippery when wet. It appears to be a painted concrete surface. Would your 501 anti slip paint be suitable for this.
	Answer from Rawlins’ Technical Team: Potentially, but as we don't know what the drive is currently painted in you will have to carry out a test area prior to full application to ensure adhesion/compatibility. After cleaning and preparation as per the product data sheets, apply 1 coat of 301 Industrial Floor Paint thinned 10% with white spirit. Allow to dry overnight, then apply 2 coats of 501 Anti Slip Floor Paint allowing at least 16 hours between coats.

chris pickering on 2018-06-03 07:26:58	Question: Hello, Just finished my Narrowboat roof in the Blue 501 Anti Slip Floor Paint. Really happy with it, but would like to detail some areas on the boat in the same colour without the aggregate. Could you supply this?
	Answer from Rawlins’ Technical Team: Yes, the nearest colour to our 501 Anti Slip Floor Paint in Blue is BS 18D43. This colour can be produced in something like Teamac Marine Gloss or Rust-Oleum CombiColor.

Jackie on 2018-03-30 18:30:16	Question: Hi,do you have a non slip paint for floor tiles? Thank you,regards Jackie
	Answer from Rawlins’ Technical Team: Smartkote Safekote can be applied to glazed tiles after the application of Smartkote Protectakote Clear Primer Treatment, see product information and data sheets for full details.

Dave on 2018-02-15 10:20:45	Question: Do you have a non slip paint suitable for an aluminium van ramp, used for wheeled flight cases?
	Answer from Rawlins’ Technical Team: We would recommend Smartkote Protectakote UVR for this. Abrade to fresh metal, clean well using detergent. Prime with Smartkote Protectakote 2K Metal Primer as per instructions within 30 minutes. Then apply Smartkote Protectakote UVR as per instructions, you may also be interested in Smartkote Protectakote UVR Accelerator and Smartkote Protectakote Safety Grip to be used in conjunction with your application.

stuart wilmot on 2017-04-02 09:12:14	Question: I want to put a non slip path on my block paved driveway using 501 anti slip floor paint. I have jetwashed the area I want to paint. Can I paint direct to this cleaned surface OR is there other preparatory work I need to do first?
	Answer from Rawlins’ Technical Team: After cleaning a priming coat of 301 Industrial Floor Paint thinned 10% with White Spirit should be used before application of 501 Anti Slip Floor Paint.

David Pontefract on 2017-03-08 17:42:11	Question: Can you tell me what primer do I need to order and is used on clean concrete when painting with 501 anti slip paint. Regards D Pontefract
	Answer from Rawlins’ Technical Team: On suitably prepared bare concrete a priming coat of 301 Industrial Floor Paint thinned 10% with White Spirits should be used before application of 501 Anti Slip Floor Paint.

Dave Robson on 2017-02-17 08:25:51	Question: Is there a primer needed on bare timber boards before applying the 501 anti slip floor paint
	Answer from Rawlins’ Technical Team: Yes - 407 Multi Surface Primer.

Scott on 2017-02-08 13:10:34	Question: Is Anti slip paint 501 suitable for an external meta staircase and can it be applied over a previous coat of anti slip paint?
	Answer from Rawlins’ Technical Team: It is suitable for use on external metal staircases. Any bare metal areas should be prepared and primed with a suitable primer. Existing paint should be well adhered, clean and abraded to provide a key if necessary before application of 501 Anti Slip Floor Paint directly to the surface.

Steve on 2016-10-19 17:31:35	Question: Hi, I am looking for a paint adhere to an aluminium truck bed for driving vehicles onto . Is your 501 antislip paint suitable? Thank you Steve
	Answer from Rawlins’ Technical Team: We would recommend priming the aluminium with 707 MMA Metal Primer and finishing with 703 MMA Flexible Anti-Slip Coating.

phu on 2016-09-20 09:54:56	Question: hi can you let me know is it ok to mop over this paint with out it coming off. thanks phu
	Answer from Rawlins’ Technical Team: Mopping this product certainly won't remove it as it is a durable coating that can also be used externally but it does have a very rough texture to the finished surface which will make it nearly impossible to mop. If you require an anti-slip coating you can clean for internal areas, we would recommend 503 Easy Clean Anti Slip Coating.

IMPORTANT SHIPPING & DELIVERY INFORMATION

501 Anti Slip Floor Paint is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT

Coo-Var Acid Etch

Acid etching solution designed to remove laitance and salts from concrete. For new concrete, power floated concrete floors, and exceptionally smooth surfaces. Non-flammable and water-soluble. Essential for ensuring proper adhesion of subsequent paint layers.

£24.73 (incl. VAT)

Shop now

In Stock and Available for Delivery

407 Multi Surface Primer

407 Multi Surface Primer is a primer/sealer which offers excellent stain blocking and alkali resisting properties across substrates such as tiles, wood, metal (including galvanised), plaster, existing paint, masonry and most plastic. Single pack Internal or external use Gives excellent coverage to a multitude of stains Touch dry in just...

£44.65 (incl. VAT)

Shop now

In Stock and Available for Delivery

301 Industrial Floor Paint

A single pack, easy to use floor paint in 8 colours which dries to a semi-gloss finish. For use on masonry, wood, cement, concrete and many other surfaces. Easy to use, versatile and economical. Touch dry in just 2 hours @ 20 °C. No primer required for concrete (just dilute 1st coat with 10% white spirit).

£51.54 (incl. VAT)

Shop now

In Stock and Available for Delivery

COVERAGE CALCULATOR
Units
Film Thickness
Total area²
Or enter length and width dimensions:
Length
Width

Follow us on:

501 Anti Slip Floor Paint

501 Anti Slip Floor Paint

Quick Links - Click To Jump To Section:

Features & Benefits

Typical Properties

Coverage

Surface Preparation

Application

Cleaning

Curing

Storage & Shelf Life

Health & Safety

Data sheet

Questions

Question about the product

IMPORTANT SHIPPING & DELIVERY INFORMATION

Coo-Var Acid Etch

407 Multi Surface Primer

301 Industrial Floor Paint