Will this be suitable to paint rubber playground tiles please ?

Assuming the tiles are soft rubber tiles, unfortunately this product wouldn't be suitable for this type of application. You could consider Kolorbond Hypakolor as an alternative, this product has been developed to bond to rubber or flexible material surfaces, and is available to 5000+ RAL, BS & NCS Colours. It will require re-coating from time to time due to being a painted finish and not a dye. We would recommend to test on a small area for compatibility and adhesion prior to full application.

What can I use to darken the colour

Assuming this product is currently applied, and the substrate is clean, dry, sound and prepared as detailed in the technical datasheet, re-applying additional coats of this product would be the best option to increase the colour strength and darkness of the colour. Nothing else can be added to the paint to darken or strengthen the colour finish.

Could this product be used on bricks edging a patio as well as the concrete paving slabs?

Assuming both the bricks and paving slabs are clean, dry, sound and prepared as detailed in the technical datasheet, providing no sealant is present on either surface, this product will be fine for application to both. A Damp-Proof Membrane isn't required to allow use of this product, however it would increase the lifespan when used if one was installed.

Will this paint be OK to repaint a impressed concrete drive. Also can I use it straight from the tin with a roller

Unfortunately no, this would not be suitable. Assuming the impressed concrete is bare, clean, dry, sound and prepared as detailed in the technical data sheet you could consider the AdSeal Imprinted Concrete Sealer with AdSeal Low-Slip Additive .

Will it prevent leaking on concrete

Please can you provide more information on the application to technical@rawlinspaints.com.

Is this the best paint for outside concrete steps leading up to my flat?

This paint is suitable for high levels of foot and vehicle traffic, when applied to a clean, dry, sound and prepared concrete substrate. The concrete should be acid etched with Flag Acid Etch Solution or ground prior to application. Then the first coat applied diluted 10% with Flag HD Thinners .

Flag Heavy Duty Elastomeric Floor Coating (Anti-Slip)

Reference FLA004

Brand Flag Paints

Search ID FLA5978

Provides excellent protection for high traffic areas, with high levels of flexibility for a long lasting durable finish. Contains Dolomite stone to provide anti-slip* properties. For interior and exterior use.

Used on Concrete, Stone, Tarmac, Asphalt (suitably aged), Ferrous Metals, Wood
Ideal for areas subjected to frequent heavy use e.g. car parks, stairs, walkways, high traffic public areas, industrial work areas, driveways, pavements, balconies
Very fine textured almost smooth finish
*Provides slip resistance - but it is not possible to guarantee a totally non-slip surface

Please note: Colours shown are for illustrative purposes only

Colour

Pick a Colour

Current colour: Mid Grey (Flag HD)

Red (Flag)
Red (Flag)
Green (Flag)
Green (Flag)
Grey (Flag)
Grey (Flag)
Blue (Flag)
Blue (Flag)
Black (Flag)
Black (Flag)
Mid Grey (Flag HD)
Mid Grey (Flag HD)
Safety Yellow (Flag)
Safety Yellow (Flag)

Size

Finish

£50.20(incl. VAT)

£41.83(ex. VAT)

Quantity

Please choose your colour

Available for Delivery (See Delivery Options Below)

ColourPicker Explained

In general we sort colours for products into 2 main groups - ‘Ready Mixed’ and ‘Tinted’.
Tinted colours will always be more expensive than Ready Mixed colours as they need to be produced at the time of order using a tinting machine dispensing colourant into a base*.
During busy periods, this means that tinted colours could take longer, for example – a ready mixed colour ordered on a 3-5 day delivery might arrive within 3 days, however a tinted colour might take the full 5 days to arrive.

To find Ready Mixed colours, search "ready mixed" or select the Ready Mixed 'colour chart'. To see Tinted colours select a colour chart such as RAL, BS, NCS, etc. or search for a colour/hue to see available or related options.

To ensure fair pricing, we split colours into ‘Price Bands’ to group together similar priced colours. If you wish to search for the cheapest tinted colours, always select Price Band 1.

We make every effort to list all available colours, however we also offer a colour match service which can be accessed by contacting our Technical Team on 0113 245 5450 (option 2) or emailing [email protected]

*Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour

Colour reproduction of the Products on the Site is limited by the technology used to deliver web pages and by the colour representation of Customer’s own monitor and computer set-up. We have made every effort to display as accurately as possible the colours of our Products but we cannot guarantee that the colour shown on Customer’s monitor’s display will accurately reflect the colour of the Product on delivery. We recommend that Customer first purchases the smallest Product available or access an industry standard colour chart in person (and not digitally) to ensure that the colour is acceptable for its purposes.

6 questions about the product

Description

Flag Heavy Duty Elastomeric Floor Coating (Anti-Slip) is a blend of high quality thermo-acrylic and polyurethane resins resulting in a heavy duty coating that offers excellent protection for high traffic areas. This product is Elastomeric and therefore offers high levels of flexibility for a long lasting durable finish. Contains Dolomite stone to provide anti-slip* properties.

For use on Concrete, Stone, Tarmac, Asphalt (suitably aged), Ferrous Metals and Wood.

It is ideal for areas that are subjected to frequent heavy use e.g. car parks, stairs, walkways, high traffic public areas, and industrial work areas. This product has a very fine textured, almost smooth, finish.

Flag Heavy Duty Elastomeric Floor Coating (Anti-Slip) is also suitable for external areas such as driveways, pavements and balconies.

*Important Note: This product has anti-slip properties and therefore provides slip resistance, however, it is not possible to guarantee a totally non-slip surface

Quick Links - Click To Jump To Section:

Features & Benefits
Application Notes

Features & Benefits

A blend of high quality thermo-acrylic and polyurethane resins resulting in a heavy duty coating
Offers excellent protection for high traffic areas
Elastomeric and offers high levels of flexibility for a long lasting durable finish
Contains Dolomite stone to provide anti-slip* properties
Suitable for interior and exterior use
Ideal for areas subjected to frequent heavy use e.g. car parks, stairs, walkways, high traffic public areas, industrial work areas
Very fine textured, almost smooth, finish
Suitable for external areas such as driveways, pavements and balconies

Application Notes

This product has anti-slip properties and therefore provides slip resistance, however, it is not possible to guarantee a totally non-slip surface
For additional guidance (e.g. power-floated floors, existing coatings, possible existing contamination etc.) please contact our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for details
It is only necessary to seal a porous substrate such as new or bare concrete
A sealer coat is achieved by adding 10% Flag HD Thinner to the paint
Please Note: New concrete floors can only be painted after 6-8 weeks

Product Details

Reference 5978-898021

Data sheet

Manufacturer: Flag Paints
For Use By: Consumer Use
For Use On: Concrete
Stone
Wood
Tarmac
Asphalt
Application Method: Brush
Roller
Sheen: Satin
Single, Two or Three Pack: Single
Pack Size: 5L
Application: Brush, Roller
Coverage: 10 -12m² per litre
Recommended Thinner/Cleaner: HD Thinners
Solids by Volume: 55%
Touch Dry: 2 hours
UN Number: UN1263
Dry to Recoat: 24 hours
Specific Gravity: 1.22
Flashpoint: 42°C
Colour(s): Standard Colours
Base Type: Solvent-Based
Suitable For Use On: Stone
Suitable For Use On: Wood Floors
Suitable For Use On: Wood
Suitable For Use On: Wooden Steps
Suitable For Use On: Concrete Floors
Suitable For Use On: Wood Steps
Suitable For Use On: Tarmac
Suitable For Use On: Concrete Walkways
Suitable For Use On: Asphalt
Suitable For Use On: Workshops
Suitable For Use On: Ferrous Metals
Suitable For Use On: Tarmac Walkways
Suitable For Use On: Stairs
Suitable For Use On: Asphalt Walkways
Suitable For Use On: Balconies
Suitable For Use On: Heavy Traffic Areas
Suitable For Use On: Driveways
Suitable For Use On: Car Parks
Suitable For Use On: Stone Floors
Suitable For Use On: Tarmac Floors
Suitable For Use On: Concrete Steps
Suitable For Use On: Concrete Workshop Floors
Suitable For Use On: Pavements
Suitable For Use On: Stone Steps
Suitable For Use On: Walkways
Suitable For Use On: Industrial Work Areas
Suitable For Use On: Asphalt Floors
Suitable For Use On: Wood Stairs
Suitable For Use On: Wooden Stairs
Suitable For Use On: Stone Stairs
Suitable For Use On: Concrete
Suitable For Use On: Concrete Stairs
Finish: Satin
Application Method: Brush
Application Method: Roller
Manufacturer: Flag Paints
Components: 1K
Usages: Anti-Slip
Product Usage Type: Topcoat
Colour Family: Grey
Colour Family: Green
Colour Family: Blue
Colour Family: Red
Colour Family: Yellow
Colour Family: Black
Anti-Slip Texture: Fine Texture

Attachments

Download

Product Data Sheet

Download

Safety Data Sheet

Download

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

Name ^*

Email ^*

Question ^*

^* Required fields

I have read and agree to the conditions of use (read)

Kelly on 2024-08-19 17:16:19	Question: Will this be suitable to paint rubber playground tiles please ?
	Answer from Rawlins’ Technical Team: Assuming the tiles are soft rubber tiles, unfortunately this product wouldn't be suitable for this type of application. You could consider Kolorbond Hypakolor as an alternative, this product has been developed to bond to rubber or flexible material surfaces, and is available to 5000+ RAL, BS & NCS Colours. It will require re-coating from time to time due to being a painted finish and not a dye. We would recommend to test on a small area for compatibility and adhesion prior to full application.

Phil on 2024-08-17 19:38:27	Question: What can I use to darken the colour
	Answer from Rawlins’ Technical Team: Assuming this product is currently applied, and the substrate is clean, dry, sound and prepared as detailed in the technical datasheet, re-applying additional coats of this product would be the best option to increase the colour strength and darkness of the colour. Nothing else can be added to the paint to darken or strengthen the colour finish.

Richard on 2024-04-03 18:26:47	Question: Could this product be used on bricks edging a patio as well as the concrete paving slabs?
	Answer from Rawlins’ Technical Team: Assuming both the bricks and paving slabs are clean, dry, sound and prepared as detailed in the technical datasheet, providing no sealant is present on either surface, this product will be fine for application to both. A Damp-Proof Membrane isn't required to allow use of this product, however it would increase the lifespan when used if one was installed.

Maureen Connelly on 2024-02-19 19:50:26	Question: Will this paint be OK to repaint a impressed concrete drive. Also can I use it straight from the tin with a roller
	Answer from Rawlins’ Technical Team: Unfortunately no, this would not be suitable. Assuming the impressed concrete is bare, clean, dry, sound and prepared as detailed in the technical data sheet you could consider the AdSeal Imprinted Concrete Sealer with AdSeal Low-Slip Additive.

DWG Roofing on 2023-09-12 14:01:54	Question: Will it prevent leaking on concrete
	Answer from Rawlins’ Technical Team: Please can you provide more information on the application to [email protected].

kerry on 2022-07-25 14:08:19	Question: Is this the best paint for outside concrete steps leading up to my flat?
	Answer from Rawlins’ Technical Team: This paint is suitable for high levels of foot and vehicle traffic, when applied to a clean, dry, sound and prepared concrete substrate. The concrete should be acid etched with Flag Acid Etch Solution or ground prior to application. Then the first coat applied diluted 10% with Flag HD Thinners.

IMPORTANT SHIPPING & DELIVERY INFORMATION

Flag Heavy Duty Elastomeric Floor Coating (Anti-Slip) is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT

Flag HD Thinners

Flag HD Thinners is a thinner for use with Flag Heavy Duty Elastomeric Floor Coating (Anti-Slip).

£9.97 (incl. VAT)

Shop now

In Stock and Available for Delivery

COVERAGE CALCULATOR
Units
Total area²
Or enter length and width dimensions:
Length
Width

Follow us on:

Flag Heavy Duty Elastomeric Floor Coating (Anti-Slip)

Flag Heavy Duty Elastomeric Floor Coating (Anti-Slip)

Quick Links - Click To Jump To Section:

Features & Benefits

Application Notes

Data sheet

Questions

Question about the product

IMPORTANT SHIPPING & DELIVERY INFORMATION

Flag HD Thinners