Thank you for your enquiry, please e-mail [email protected] with further details of your requirements, including confirming if the GRP Coated wood is trafficked and previously coated. 

This product would be well suited for pedestrian traffic.

Assuming the timber is prepared as detailed in the technical datasheet, we'd recommend cleaning firstly with Rust-Oleum 2901 Epoxyshield Degreaser/Cleaner to remove oils/greasy contaminations from the surface, being mindful to use it quickly so the cleaner doesn't leach into the timber substrate.

You'd need a first coat of Rust-Oleum 7200 Floorcoat PU to Prime the timber, if applied with Brush/Roller, this should be diluted 5% with Rust-Oleum Thinner 633, as this will improve adhesion on the timber, before 2 coats of Rust-Oleum 7100NS Anti-Slip Floor Coating in your chosen colour, which is a solvent-based, gloss finish paint.

A mild detergent cleaner can be applied when cleaning is required, but the anti-slip rough surface will make it more difficult to maintain as easy as a smoother surface would.

Assuming the concrete is clean, dry, sound and prepared in accordance with the technical data sheet, the ramp doesn't have a steep incline, and the concrete floor is older than 2 years, this product will be suitable for this application type.

This product could be used, but we would recommend that once the sandstone slab is clean, dry and sound it is first painted with Rust-Oleum 7200 Floorcoat PU to take up any porosity there may be in the sandstone

Unfortunately we do not have a product we can recommend for this application.

Grp anti-slip fork covers would be more suitable.

Assuming the steel steps are bare, clean, dry, sound and prepared as detailed in the technical data sheet we would recommend they are primed first with Coo-Var Zinc Phosphate Primer then two coats of Coo-Var Suregrip Anti-Slip Floor Paint - Special Colour.

This can be mixed to RAL 7016 aswell as many other RAL, NCS or BS colours.

Unfortunately no, we do not have a product tested as pet safe.

Rust-Oleum 7100NS Anti-Slip Floor Coating is a floor paint, unfortunately if this is to be used on an area subject to foot traffic we would not recommend its use over Rust-Oleum 7500 Alkythane as this product is not suitable.

Assuming the Rust-Oleum 7500 Alkythane is removed back to bare metal, the metal grill is steel, it is clean, dry, sound and prepared as detailed in the technical data sheet Rust-Oleum 7100NS Anti-Slip Floor Coating could be applied once the area is primed with Rust-Oleum 569/580 QD Metal Primer.

Unfortunately no, but assuming the vinyl or rubber floor is nitrile or chloroprene, it is clean, dry, sound and prepared as detailed in the technical data sheet we can recommend Smartkote Safekote.

This is a barefoot friendly anti-slip paint available in a range of colours or a clear option.

The floor must be cleaned with Xylene, a test for compatibility and adhesion is recommended prior to full application.

While this can be used internally or externally and on bare timber, the timber must be clean, dry, sound and prepared as detailed in the technical data sheet.

Due to decking rarely being painted on the underside and the exposure, the life span of paint on a timber decking may be short.

No unfortuntely this would not be suitable for this application.

Most driveways will not have a damp proof membrane present, unfortunately without this we cannot offer an antislip paint for this application.

Assuming the metal staircase is bare, made of steel, it is clean, dry, sound, prepared as detailed in the technical data sheet and primed with Rust-Oleum 569/580 Quick Drying Metal Primer prior to application Rust-Oleum 7100NS Anti-Slip Floor Coating can be used.

We would instead suggest Smartkote Safekote. Abrade, clean and allow to completely dry before applying Safekote directly. Dilute the first coat with 10% Xylene to aid penetration.