- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
A rapid curing, general purpose primer enabling fast overcoating. The product exhibits outstanding adhesion to concrete, as well as steel, masonry, and marine plywood, and the fast curing characteristics allow rapid application of subsequent coatings, mortars or screeds.
- Ideal for use as a rapid curing primer for concrete, steel, masonry, and marine plywood
- Rapid cure, even at low temperatures - from as low as -30°C*
- Very good chemical resistance
- Impervious to water
- Pre-packed units ready for use
- Easily applied
- Can be overcoated after 40 minutes @ 20°C
- 5kg pack is sufficient to prime an area of 15-20m²
- Images are for illustrative purposes only and may differ from the actual product
- This product is for Professional Use Only
*Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
706 MMA Floor Primer is a rapid curing, general purpose primer enabling fast overcoating. The product exhibits outstanding adhesion to concrete, as well as steel, masonry, and marine plywood, and the fast curing characteristics allow rapid application of subsequent coatings, mortars or screeds.
706 MMA Floor Primer has been developed as a general purpose primer, being used prior to any of our MMA range of coatings, mortars, and screeds.
706 MMA Floor Primer is supplied as a two pack material, comprising pre-weighed amounts of Base and Catalyst components. The mix ratio is fairly tolerant to variations within the range of 1% to 5% addition of Catalyst, so that part packs may be used if care is exercised.
This product is for Professional Use Only.
Recommended Uses:
- As a rapid curing primer for concrete, steel, masonry, and marine plywood
Quick Links - Click To Jump To Section:
- Features & Benefits
- Typical Properties
- Coverage
- Surface Preparation
- Application
- Cleaning
- Curing
- Limitations
- Storage & Shelf Life
- Health & Safety
Features & Benefits
- Ideal for use as a rapid curing primer for concrete, steel, masonry, and marine plywood
- Rapid cure, even at low temperatures - from as low as -30°C*
- Very good chemical resistance
- Impervious to water
- Pre-packed units ready for use
- Easily applied
- Can be overcoated after 40 minutes @ 20°C
- 5kg pack is sufficient to prime an area of 15-20m²
- Developed as a general purpose primer, being used prior to any of our MMA range of coatings, mortars, and screeds
- Two pack
*Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Typical Properties
Technical Data | |
---|---|
706 MMA Floor Primer | |
Viscosity: | 300 cps @ 20°C |
Pot life @ 20°C: | 15 Minutes |
Pot life @ 10°C: | 25 minutes |
Adhesion to concrete: | 3.5MPa (concrete failure) |
Temp. range during application: | -30°C* to + 40°C |
Temp. range during service: | -40°C to + 60°C |
*Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Coverage
- A 5kg pack is sufficient to prime an area of 15-20m²
- Exceptionally porous surfaces may require a second coat
Surface Preparation
- Concrete surfaces shall be a minimum of 21 days old and/or the residual moisture content shall be below 6%
- Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound, and existing paint finishes, etc
- Suitable mechanical treatment such as vacuum grit blasting or mechanical scabbling is recommended to ensure the removal of contaminants and to provide a mechanical ‘key’ for the primer
Mixing:
- Pour the contents of the catalyst container into the base container and thoroughly mix, preferably by mechanical means
Mixing Ratio:
- (% Catalyst by Weight) = 2.4
Application
- Apply by squeegee to distribute evenly over the floor, and then use a long nap lambswool roller to achieve a nominal application rate of 0.25-0.30kg/m²
- Allow to cure for a minimum of 40 minutes prior to applying any other MMA products from our range
- If an interval of more than 8 hours between primer application and subsequent overcoating is anticipated then the primer shall be scattered with fine silica sand before hardening
Cleaning
- Clean equipment with 109 Tool Cleaner prior to curing of the coating
Curing
- Minimum overcoating interval: 40 minutes @ 20°C
Limitations
- Do not apply to wet, uncured concrete surfaces
706 MMA Floor Primer will taint food during application, so that all foodstuffs in the immediate vicinity must be removed or properly covered
Storage & Shelf Life
- Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 20°C
- Adequate ventilation of the storage area should be provided
- Keep container tightly closed when not in use
- 706 MMA Floor Primer has a minimum shelf life of six months when stored in original, unopened containers in accordance with manufacturer’s instructions
Health & Safety
706 MMA Floor Primer is flammable during application, so adequate safety precautions should be observed.
- Avoid contact of the material with skin and eyes
- Wear gloves and goggles
- Wash off splashes immediately with soap and water
- Any eye contamination must be rapidly irrigated with copious amounts of clean water, and immediate medical attention sought
- Please refer to Material Safety Data Sheet for additional information
- 706 MMA Floor Primer shall be applied strictly in accordance with the manufacturer’s instructions
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Data sheet
- For Use By
- Professional Use
- Application Method
- Roller
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 5KG
- Dry to Recoat (at 20°C)
- 40 mins
- Pot Life (at 20°C)
- 15 mins
- Coverage
- A 5kg pack is sufficient to prime an area of 15-20m²
- Max. Application Temperature
- 40°C
- Min. Application Temperature
- -30°C
- Shelf Life (from date of manufacture)
- 6 months
- Touch Dry
- 40 Mins
- UN Number (Activator)
- UN3106
- UN Number (Base)
- UN1866
- Viscosity
- 300 cps @ 20°C
- Suitable For Use On
- Masonry
- Suitable For Use On
- Concrete
- Suitable For Use On
- Steel
- Suitable For Use On
- Plywood
- Application Method
- Roller
- Components
- 2K
- Usages
- Low Temperature
- Product Usage Type
- Primer
- Product Category
- Paints
- Colour Family
- Yellow
- Categorised As
- Floor Paints > Low Temperature Floor Primers
- Seasonal
- Cold Weather
- Product Type
- MMA
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
706 MMA Floor Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT