Follow us on:

Mapei Mapeproof ESM | Solvent Free Epoxy Resin

Mapei Mapeproof ESM

MAP10015
MAP10015

A two-component, solvent free, pure epoxy resin, used as a moisture vapour barrier on cement-based substrates containing high residual moisture.

  • For professional use
  • Low viscosity product with high penetration capacity in the porosity of the substrate
  • Because of the absence of solvents, and very low odour it can be used in inhabited environments (e.g. hospitals, schools, offices, etc)
  • Coverage: Approx 5m² per 1kg
  • Shelf life: 24 months

Colour
Size
£30.17(incl. VAT)
£25.14(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

Quick Links - Click To Jump To Section:




Mixing


  • The components should not be mixed until the application is ready to start and should be applied as soon as mixing is completed
  • The two components are supplied in pre-measured ratios:
    • Part A: 3 parts by weight
    • Part B: 1 part by weight
  • Mix the two components completely and accurately with a low speed mixer until a uniform mix is obtained



Application


Power Floated and New Substrates:

  • The substrate should be abraded by mechanical means to remove any curing agents or contamination, to assist penetration and adhesion of the membrane
  • The area should then be thoroughly vacuumed to remove all dust and debris
  • Apply the first coat of Mapeproof ESM ensuring it is well worked into the substrate and that complete coverage of the area is achieved at a maximum rate of 20m² per 4kg unit (depends on the porosity of the sub-floor) and allow to cure (approx 5 hours)
  • Apply the second coat of Mapeproof ESM at right angles to the first coat, again ensuring complete coverage
  • When the second coat has cured, a coat of Eco Prim T Plus or Eco Prim Grip primer should then be applied within maximum 24 hours (primer drying times vary with ambient conditions i.e. temperature and humidity)
  • The levelling compounds should be applied within 24 hours of the primer application

Sand/Cement and Existing Substrates:

  • All existing materials, adhesives, laitance and contamination should be removed prior to preparation work commencing
  • Any cracks in the substrate should be filled with Eporip
  • Where the substrate has a textured or profiled finish, Latexplan Trade levelling compound should be applied to provide a level surface for the membrane to be applied onto
  • Apply the first coat of Mapeproof ESM ensuring it is well worked into the substrate and that complete coverage of the area is achieved at a maximum rate of 20 m² per 4 kg unit (depends on the porosity of the sub-floor) and allow to cure (approx 5 hours)
  • Apply the second coat of Mapeproof ESM at right angles to the first coat, again ensuring complete coverage
  • When the second coat has cured, a coat of Eco Prim T Plus or Eco Prim Grip primer should then be applied within maximum 24 hours. (primer drying times vary with ambient conditions i.e. temperature and humidity)
  • The levelling compound should be applied within 24 hours of the primer application
  • If required, the second coat of Mapeproof ESM can be blinded with sharp sand (when still fresh), which removes the need for a primer
  • It is essential that pinhole free coatings be achieved

Underfloor Heating:

  • The screed must be allowed to cure for a minimum 28 day period
  • The underfloor heating must be commissioned prior to the installation commencing; it should be turned on to +5°C and the temperature increased by +5°C per day up to a maximum +27°C, run at this temperature for several days then cooled down and switched off for at least 48 hours
  • Up to a level of 97% RH, 2 coats of Mapeproof ESM should be applied
  • The heating must then remain off for a further 48 hours (minimum) after completion of the installation, and when turned back on run at a maximum temperature of +27°C in accordance with BS 8203 and BS 5325

Cleaning:

  • Mapeproof ESM can be cleaned from tools and clothing with ethyl alcohol while the product is still fresh



Safety Instructions


  • Mapeproof ESM component A is irritant for the eyes and skin
  • Both components A and B may cause sensitisation if they come into contact with the skin of those predisposed
  • Mapeproof ESM component B is corrosive, may cause burns and damage to eyes
  • The product contains low molecular weight epoxy resins that may cause sensitisation if crosscontamination occurs with other epoxy compounds
  • During use, wear protective gloves and goggles and take the usual precautions for handling chemicals
  • If the product comes in contact with the eyes or skin, wash immediately with plenty of water and seek medical attention
  • Mapeproof ESM components A and B are also hazardous for aquatic life
  • Do not dispose of these products in the environment
  • For further and complete information about the safe use of our product please refer to the latest version of our Safety Data Sheet (see 'Data Sheets' section above)

Product Details
10015-971939

Data sheet

Manufacturer
Mapei
For Use By
Professional Use
Interior / Exterior Use
Interior & Exterior
For Use On
Cement Floors
Application Method
Roller
Single, Two or Three Pack
Two-Pack
Pack Size
1KG kit
4KG kit
Coverage
5m² per 1kg unit
20m² per 4kg unit
Max. Application Temperature
30°C
Min. Application Temperature
10°C
Density
1.1g/cm³
UN Number (Activator)
UN3082
UN Number (Base)
UN2735
Fully Cured (at 23°C)
7 days
Base Type
Solvent-Free
Suitable For Use On
Cementitious Floors
Application Method
Roller
Manufacturer
Mapei
Components
2K
Usages
Damp Tolerant
Product Usage Type
Primer
Product Range
Mapeproof
Workability Time
60 minutes (at 30°c) to 120 minutes (at 10°c)
Setting Time
2-3 hours (at 30°c) to 5-6 hours (at 10°c)
Colour Family
Clear
Viscosity Brookfield (cP)
300 (# 1 - rpm 10)
Product Type
Epoxy
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

Mapei Mapeproof ESM is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT