Follow us on:

PPG SteelGuard 651
PPG SteelGuard 651

PPG SteelGuard 651

359402
PPG10138

A one-component, thin-film, waterborne intumescent coating for fire protection of structural steelwork. Provides up to 120 minutes protection from cellulosic fires.

  • Suitable for C1, C2 and C3 internal environments (ISO 12944)
  • For dry internal (C1) environments no topcoat is required
  • Tested and assessed to EN13381-8, BS476-20/21 and GB14907
  • CE marked product, ETA22/0050
  • On-site application
  • For detailed project information please complete the Structural Steelwork Information Request Form
Colour
Size
Finish
£66.95(incl. VAT)
£55.79(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

PPG Steelguard 651 is a one-component, thin-film, waterborne intumescent coating for fire protection of structural steelwork. Provides up to 120 minutes protection from cellulosic fires.

For detailed project information please complete the Structural Steelwork Information Request Form.





Quick Links - Click To Jump To Section:




Features & Benefits


       
  • Provides up to 120 minutes protection from cellulosic fires
  • On-site application
  • Up to 700 µm (28.0 mils) DFT in a single coat
  • Suitable for C1, C2 and C3 internal environments (ISO 12944) ; for dry internal (C1) environments no topcoat is required
  • Tested and assessed to EN13381-8, BS476-20/21 and GB14907
  • CE marked product, ETA 22/0050
  • Assessed to EAD 350402-00-1106 for Z1, Z2 and Y
  • Matt Finish



Application Notes


Recommended Substrate Conditions and Temperatures

  • Approved primer must be sound, dry and free from any contamination
  • Substrate temperature during application and curing should be between 10°C (50°F) and 40°C (104°F)
  • Substrate temperature during application and curing should be at least 3°C (5°F) above dew point
  • Ambient temperature during application and curing should be between 10°C (50°F) and 40°C (104°F)
  • Relative humidity during application and curing should not exceed 80%

 

Instructions for Use

  • Stir thoroughly until homogeneous and free of lumps
  • Adding too much water results in reduced sag resistance and slower cure
  • Must be protected from freezing at all times during storage and/or transport

 

Airless Spray

  • Recommended thinner: Tap Water (normally no thinner required)
  • Volume of thinner: 0 - 5%
  • Nozzle angle: 20° – 50°, depending on shape of steel parts
  • Nozzle orifice: Approx. 0.43 – 0.53 mm (0.017 – 0.021 in)
  • Nozzle pressure: 20.0 MPa (approx. 200 bar; 2901 p.s.i.)

 

Notes: All filters, including surge bottle and gun filters to be removed. External fluid uptake pipe filter is recommended.

 

Brush/Roller

  • For small areas only (touch up and repair)
  • No thinner should be added

 

Cleaning Solvent

  • Tap Water



Product Data & Drying Times


Data for Product
Number of components One
Mass density 1.41kg/l (11.77lb/US gal)
Volume solids 70±3%
VOC (Supplied) Directive 2010/75/EU, SED: max. 0.2 g/kg EUR Directive: 2004/42/IIA(i) (140) 3 g/l
Recommended dry film thickness 200 - 700 µm (8.0 - 28.0 mils) per coat
Theoretical spreading rate 1.00m²/l  for 700µm (40ft²/US gal for 28.0mils)
Dry to touch 2 hours
Overcoating interval Minimum: 16 hours
Maximum: Unlimited
Shelf life At least 12 months when stored cool and dry



Spreading rate and film thickness
DFT Theoretical spreading rate
200 µm (8.0 mils) 3.50m²/l (140ft²/US gal)
400 µm (16.0 mils) 1.75m²/l (70ft²/US gal)
500 µm (20.0 mils) 1.40m²/l (56ft²/US gal)
700 µm (28.0 mils) 1.00m²/l (40ft²/US gal)



Note : Maximum DFT when brushing : 300µm (12.0 mils)



Overcoating interval for DFT up to 700 µm (28 mils)
Overcoating with... Interval 10°C (50°F) 15°C (59°F) 20°C (68°F) 30°C (86°F)
Itself

Minimum


Maximum

24 hours


Unlimited

20 hours


Unlimited

16 hours


Unlimited

12 hours


Unlimited

Approved Topcoats

Minimum


Maximum

24 hours


Unlimited

20 hours


Unlimited

18 hours


Unlimited

14 hours


Unlimited



Notes:

  • All overcoating times have been measured at an intumescent wet film thickness of 1000µm (approx. 700µm DFT) under controlled temperature and relative humidity below 85%. Higher thicknesses will take longer to cure
  • The system should be dry to handle and a coating thickness gauge should not leave an indentation on the surface prior to applying subsequent coats
  • Curing time(s)/overcoating interval(s) may be extended at higher applied DFT’s and/or there is a change in environmental conditions
  • Prior to application of a topcoat, the applicator must ensure that the specified dry film thickness has been achieved



Curing time for DFT up to 700 µm (28.0 mils)
Substrate Temp. Dry to Touch
10°C (50°F) 4 hours
15°C (59°F) 3 hours
20°C (68°F) 2 hours
30°C (86°F) 1 hour



Note: All curing times have been measured at an intumescent wet film thickness of 1000µm (approx. 700µm DFT) under controlled temperature and relative humidity below 85%. Higher thicknesses will take longer to cure



IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.



Product Details
10138-975042

Data sheet

Manufacturer
PPG
Interior / Exterior Use
Interior Use
Parts
One
Base Type
Water-borne
Suitable Substrates
Structural steel
Application
Spray
Touch Dry (at 20°C)
2 hours
Dry to Recoat (at 20°C)
16 hours
Coverage
1.00 m²/l for 700 µm
Recommended Thinner/Cleaner
Water
Max. Application Temperature
40°C
Min. Application Temperature
10°C
Density
1.41kg/l
Solids by Volume
70 ± 3%
VOC
Directive 2010/75/EU, SED: max. 0.2 g/kg EUR Directive: 2004/42/IIA(i) (140) 3 g/l
Shelf Life (Once Opened)
At least 12 months when stored cool and dry
UN Number
N/A
Base Type
Water-Based
Suitable For Use On
Steel
Finish
Matt
Application Method
Spray
Product Usage Type
Basecoat
Product Range
Steelguard
Colour Family
White
Fire Rating
120 Minutes
Site Application
On-Site
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

PPG SteelGuard 651 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like
Hand & Power Tool Surface Preparation Kits for Steel

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £25.93 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery