Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product. Should you require training, visit - https://www.safeusediisocyanates.eu/

Quick Links - Click To Jump To Section:

   
• Features & Benefits
• Certification & Testing
• Areas of Use
• Installation
• Performance Data

Features & Benefits

• Flexible, high performance 2-component PU Sealer
• Expands on application, filling apertures and openings quickly and cleanly
• Conditioned to Type Z1 in accordance with EOTA TR024
• Tested in accordance with many major global certification standards
• Easy gunning and tooling
• Tested practically, with the installer in mind
• Manufactured and tested alongside the entire PyroSeal System range

Certification & Testing

• Tested in accordance with EN1366-3:2009 – Fire Resistance – Penetration Seals
• Classified in accordance with EN13501-2 – Fire Resistance
• Classified in accordance with EN13501-1 – Reaction to Fire
• CE Marked – ETA 18-0897
• Conditioned in accordance with EOTA TR024 – Z1 Type
• Tested in accordance with EN10140-2:2010 – Airborne Sound
• Tested in accordance with EN1026:2016 - Air Permeability
• Tested in accordance with EN12667:2001 & EN12664:2001 - Thermal Properties

Areas of Use

• To reinstate fire resistance through walls and floors
• Prevention of air leakage
• Maintains Acoustic performance
• Assumed working life 10 years

Installation

If the mixing nozzle is clogged, never use force to press out the material, force can destroy the cartridge or the dispensing gun. Wear suitable protective gloves, safety glasses and protective clothing for the work.

1. Clean the appature or opening. Cardboard, plastic sheet or duct tape can be used as form work and it can remain on the surface
2. Hold the cartridge vertically with the cap pointing upward, unscrew the cap and firmly screw on the provided mixing nozzle
3. Insert the cartridge into the intended dispensing gun
4. Start pressing out and discard non-mixed initial material
5. Fill the opening from back to front. In this process build up the foam from bottom to top, always guide the tip of the mixing nozzle above the foam so that the material does not stick or clog. After a work interruption longer than approximately 50 seconds the foam hardens in the mixing nozzle, which then must be replaced. Prior to changing the mixing nozzle, offload the dispensing gun, and carefully replace the mixing nozzle
6. After approx. 2 minutes projecting foam residues can be cut off with a suitable knife in compliance with the necessary protective measures and safety regulations
7. Cables or pipes that will be installed retroactively can be routed through the existing foam. Refill gaps due to removed cables or pipes with PyroSeal 2k
8. Large free areas can be filled with PyroSealBricks

Processing of PyroSeal Brick

1. Areas that are not penetrated by cables, cable support systems, conduits or pipes can be sealed with PyroSeal Brick
2. The PyroSeal Brick must be installed in such a manner that the minimum seal thickness is maintained
3. Remove the protective foil of the PyroSeal Brick and install them in layers (like in a brick wall, i.e. layer-by-layer offset of the vertical butt joints) so that they fit tightly in the opening

Performance Data

Refer to data sheet for performance data for floors, walls, Direct field of application – DiAP and Extended Field of Application- EXAP

IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.