- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Axalta Modified Vinyl Primer/Finish (previously Stokes Modified Vinyl), a vinyl one coat anti-corrosive primer/finish for steelwork and galvanised steel where a one coat*, sheen primer/finish is required.
- Can be applied to degreased new galvanising without the need for an etch primer
- Use for gates, fences, street furniture and structural steelwork
- Available in Black, White, and 400+ RAL and BS shades
- MIO colours available on request:
- Moss Green (IP174)
- MIO Silver (IP195)
- MIO Black (IP196)
- MIO colours available on request:
- Resistant to weak acids and alkalis
- Highly moisture resistant
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cartAxalta Modified Vinyl Primer/Finish, a vinyl one coat anti-corrosive primer/finish for steelwork and galvanised steel, which does not need an etch primer.
Approvals/Certification - Please consult Axalta Coating Systems or Rawlins Paints Technical on 0113 2455450 (option 2) or send a message to [email protected]
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Mixing
- Thinner
- Application Conditions
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- Where a one coat*, semi-gloss primer/finish is required.
- Can be applied to degreased new galvanising without the need for an etch primer.
- Available in Black, White, and 400+ RAL and BS shades
- Use for gates, fences, street furniture and structural steelwork.
- Resistant to weak acids and alkalis.
- Highly moisture resistant.
*Colours such as yellows, reds and oranges have lower opacity, especially when produced using lead-free pigments. Two or three coats of these shades may be required, relative to only one coat of a grey or red oxide, so that yellows, bright reds and oranges may not be suitable as one coat systems.
Product Specification
Technical Data | |
---|---|
Volume Solids | 35 ± 2% (varies with colour) |
VOC Content | 545 + 54 g/litre (varies considerably with colour) |
SG | 1.33 + 0.27 kg/lt (varies with colour) |
Storage Conditions | Store in dry, cool conditions and protect from frost. |
Shelf Life | Minimum 12 months if stored as above in unopened containers. |
Flash Point | 23-60℃ |
Film Thickness Range And Coverage
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | Theoretical Coverage | |
Typical | 50 µm | 143 µm | 7.0 m² /litre |
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated. |
Drying Times
Product Data | |||||
---|---|---|---|---|---|
Applied to 50 microns DFT | 10℃ | 23℃ | 35℃ | ||
Dust Free | 2 hours | 1 hour | 30 min | ||
Hard Dry | 30 hr | 24 hr | 12 hr | ||
Overcoating | Minimum | 6 hr | 3 hr | 2 hr | |
Maximum | Indefinite if clean and sound | ||||
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation. |
Surface Preparation
- All surfaces to be coated should be dry and cleaned as necessary to remove all oil, grease, salts, weld flux or other contamination. Where necessary, remove weld spatter and grind smooth all sharp edges and weld seams.
- Steelwork: Blast clean to Sa2½ (ISO 8501-1:2007), surface profile 50-75 microns.
- Galvanising: thoroughly degrease and lightly abrade any very shiny areas.
Mixing
Must be mixed thoroughly by using a mechanical agitator before use. Agitate periodically to ensure paint remains homogeneous.
Thinner
Axalta Thinner General Industrial TH004 (formerly called No.7 Thinner)
Application Conditions
- Only apply in conditions of good ventilation which must be maintained during drying and curing.
- Do not apply when rain, mist, sleet or snow are imminent.
- During application and drying time of the paint coating, the surface should be dry, the Relative Humidity should not exceed 85% and the steel temperature should remain at least 3ºC above the dew point.
- Paint temperature should ideally be at a minimum of 15ºC.
Application Methods
Method | Airless Spray | Conventional Spray | Brush | Roller |
---|---|---|---|---|
Yes | No | Yes | No |
- Airless Spray: Output fluid pressure at tip 2000 psi, Tip Size 13-17 thou (0.33- 0.43 mm), some thinning may be required
- Conventional spray – not recommended, as considerable thinning would be required for suitable atomisation and build would be greatly reduced
- Application by brush – supplied ready for use
Product Notes
- 2 coats at 50µm per coat are recommended for bare steel (i.e. non-galvanised), for galvanised surfaces with a degree of roughness, and where extended protection is required
- When applied to bare (non-galvanised) steel: in common with most single pack primers and primer/finishes, this product is not recommended for extended exterior exposure, or exposure in aggressive or coastal locations, or for immersion. Epoxy primers are preferred for these conditions, please consult Rawlins Paints Technical on 0113 2455450 (option 2) or send a message to [email protected] for advice.
- *Colours such as yellows, reds and oranges have lower opacity, especially when produced using lead-free pigments. Two or three coats of these shades may be required, relative to only one coat of a grey or red oxide, so that yellows, bright reds and oranges may not be suitable as one coat systems.
Health & Safety
Containers are provided with safety labels which should be observed. Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets. A Safety Data Sheet for this product is available on request from Axalta Coating Systems, or from the attachments section above.
Data sheet
- Manufacturer
- Axalta
- Water / Solvent Based
- Solvent
- For Use On
- Steel, Galvanized Steel
- Application Method
- Airless Spray, Spray, Brush
- Sheen
- Sheen
- Colour
- Fully Tintable
- Single, Two or Three Pack
- Single
- Pack Size
- 5L
- Key Features
- Wide colour range. Resistant to weak acids and alkalis. Highly moisture resistant.
- Coverage
- 7m² per litre
- Recommended Thinner/Cleaner
- TH004 Thinner
- Min. Application Temperature
- 15ºC
- Min. Application Temperature
- Steel temperature should remain at least 3ºC. Paint temperature should ideally be at a minimum of 15ºC
- VOC
- 545 + 54 g/litre (varies considerably with colour)
- Shelf Life (from date of manufacture)
- Minimum 12 months if stored as above in unopened containers
- Recommended Dry Film Thickness
- 50 µm
- Recommended Wet Film Thickness
- 143 µm
- UN Number
- UN1263
- Dry to Recoat (at 23°C)
- 3 hours
- Hard Dry
- 23C - 24 hours
- Flashpoint
- 23-60C
- Base Type
- Solvent-Based
- Suitable For Use On
- Steel
- Suitable For Use On
- Galvanised Steel
- Application Method
- Brush
- Application Method
- Spray
- Product Usage Type
- Primer & Topcoat
- Colour Family
- Neutral
- Colour Family
- Dark
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- White
- Product Type
- Vinyl
- Environment
- Atmospheric
- Touch Dry/Dust Free (@ 20-25°C)
- 60 mins
- Product Attributes
- 1 coat
- Product Attributes
- Anti-Corrosive
- Product Attributes
- Primer/Finish
- Product Attributes
- Zinc Phosphate
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Axalta Modified Vinyl Primer/Finish is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Axalta 1006 Thinner
We no longer stock this product, but can recommend Axalta Thinner Fast Industrial (TH120) as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team...
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...