- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Two-component, high solids, high-build zinc phosphate polyurethane primer/finish.
- Available in 2,600+ colours, inc. RAL, BS, NCS & the new NCS 2050 colours
- Fast curing
- Specially designed for in-shop application
- Easy application by airless spray
- Unlimited recoatable
- Good adhesion to steel and galvanized steel Good resistance to atmospheric exposure
- Good color and gloss retention
- Cures down to -5°C (23°F)
- Drying and curing times can be reduced significantly using PPG 866M ACCELERATOR
- Professional application only
Product customisation
Don't forget to save your customization to be able to add to cartDescription
Quick Links - Click To Jump To Section:
Industrial Segments
- Infrastructure
- Mining
- Oil, Gas & Chemical
- Power
- Airports
- Bridges
- Commercial Buildings
- Fossil
- Rail
- Stadiums & Venues
- Wind
Recommended Substrate Conditions and Temperatures
Steel
- Steel; blast cleaned to ISO-Sa2/z, blasting profile 40 - 70 pm (1.6 -2.8 mils)
Galvanized Steel
- Surface must be dry and free from any contamination
- Surface should be sufficiently roughened (e.g. sandpapering, sweep blasting)
Substrate Temperature
- Substrate temperature during application and curing should be at least 3°C (5°F} above dew point
- Substrate temperature during application and curing down to -5°C (23°F} is acceptable; provided the substrate is free from ice and dry
- Relative humidity during application and curing should not exceed 85%
Instructions For Use
Mixing ratio by volume: base to hardener 9O:1O (9:1)
- The temperature of the mixed base and hardener should be above 1O°C (50°F}, otherwise extra thinner may be required to obtain application viscosity
- Adding too much thinner results in reduced sag resistance and slower cure
- Thinner should be added after mixing the components
Induction time
None
Air spray
- Recommended thinner: THINNER 21-06
- Volume of thinner: 5 - 10%, depending on required thickness and application conditions
- Nozzle orifice: 1.0 -1.5 mm (approx. 0.040 - 0.060 in)
- Nozzle pressure: 0.3 - 0.4 MPa (approx. 3 - 4 bar; 44 - 58 p.s.i.)
Airless spray
- Recommended thinner: THINNER 21-06
- Volume of thinner: 0 - 5%, depending on required thickness and application conditions
- Nozzle orifice: Approx. 0.46 mm (0.018 in)
- Nozzle pressure: 15.0 MPa (approx. 150 bar; 2176 p.s.i.)
Brush/roller
- Recommended thinner: THINNER 21-06
- Volume of thinner: 0 - 5%
Cleaning solvent
- THINNER: 90-53
Product Details
10396-983995
Data sheet
- Manufacturer
- PPG
- For Use By
- Professional Use
- For Use By
- Industrial Use
- Interior / Exterior Use
- Exterior Use
- For Use On
- Steel
- For Use On
- Steel
- Application Method
- Spray
- Sheen
- Semi-gloss
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 4L, 20L
- Pack Size
- 4L
20L - Pot Life (at 20°C)
- 3 hours
- Coverage
- 75 µm (3.0 mils) 8.9 m2/I
100 µm (4.0 mils) 6.7 m2/I
150 µm (6.0 mils) 4.5 m2/I - Touch Dry
- -5°C 8 hours
0°C 5 hours
5°C 2.5 hours
10°C 2 hours
20°C 1 hours
30°C 45 minutes - Pot Life
- 10°C 4 hours
20°C 3 hours
30°C 1 hour - Fully Cured
- -5°C 15 days
0°C 11 days
5°C 8 days
10°C 5 days
20°C 4 days
30°C 3 days - Dry to Handle
- -5°C 24 hours
0°C 15 hours
5°C 8 hours
10°C 3 hours
20°C 2 hours
30°C 1.5 hours - Colour(s)
- Fully Tintable
- Base Type
- Solvent-Based
- Suitable For Use On
- Galvanised Steel
- Suitable For Use On
- Steel
- Finish
- Semi-Gloss
- Application Method
- Spray
- Manufacturer
- PPG
- Usages
- High Solids
- Usages
- High Build
- Usages
- In-Shop Application
- Usages
- Primer/Finish
- Usages
- Fast Curing
- Usages
- Unlimited Recoatable
- Product Usage Type
- Primer & Topcoat
- Product Range
- SigmaFast
- Maximum Overcoating Time
- -5°C - 30°C unlimited
- Minimum Overcoating Time
- with itself and two-component polyurethane finishes:
-5°C 24 hours
0°C 18 hours
10°C 8 hours
20°C 6 hours
30°C 4 hours - Minimum Overcoating Time
- with itself and two-component polyurethane finishes:
-5°C 20 hours
0°C 16 hours
10°C 6 hours
20°C 4 hours
30°C 3 hours - Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- White
- Colour Family
- Neutral
- Colour Family
- Anthracite Grey
Questions
Question about the product
Mats hansson
on
2024-09-30 11:28:30
| Question:
Hello, to overcoat the 210 hs without sanding, ie chemically boding… how much time between coats to avoid sanding please Greetings, Mats Hansson |
Answer from Rawlins’ Technical Team:
There is no limit on time before overcoating on this product, however the manufactuer does recommend lightly abrading between multiple coats to keep a clean surface and provide a key. | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
PPG SigmaFast 210HS is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
You might also like
