Resin Technologies Food Safe Kitchen Floor Paint is supplied in two pack sizes: 2.5kg and 5kg. Each unit is split between PART A and PART B (PART C* - aggregate is an optional component if a Coarse anti-slip profile is chosen from the menu above). Weight measurements are for the whole unit.

*Aggregate is only provided separately for the Coarse Anti-Slip option. For Medium and Fine Anti-Slip aggregate is pre-mixed in the blend already making the product a 2-part system 

Please note Gloss levels for this product are dependent on the anti-slip grade selected.

Quick Links - Click To Jump To Section:

   
• Features & Benefits
• Typical Properties
• Curing
• Mixing
• Surface Preparation
• Application
• Limitations
• Health & Safety

Features & Benefits

   
• Anti-bacterial properties
• Ideal for complying with Food Safety Regulations
• Anti-slip options available
• Suitable in a kitchen or factory setting
• Hard-wearing, attractive finish

Typical Properties

*Note - Aggregate will only be provided separately for Coarse option, medium and fine are pre-mixed into PART A tin

Curing

Mixing

• Gently stir PART A for 2 minutes to ensure dispersal of pigment
• Once stirred, pour 100% contents of PART B into the PART A tin and thoroughly mix by mechanical means (a paddle on the end of a drill) for 90 seconds, or until a uniform colour and texture is achieved and the curing agent has fully dispersed
• Please note that after mixing both components, 100% of the material must be used in a single application and cannot be stored for later use as chemical curing will occur

Surface Preparation

• Ensure that the concrete is clean and free from dust, laitance, oil etc
• Defective concrete should be made good using a repair mortar such as Resin Technologies All In One Repair Mortar
• A relevant Primer should be used such as Resin Technologies All Purpose Primer
• Suitable mechanical treatment, such as using a surface grinder, is the preferred treatment prior to application, as this ensures a mechanical “key” for the coating
• However, in instances where this is not feasible, acid etching can also be used for this purpose. Please see Resin Technologies Etch & Clean

Please Note: For substrates other than Concrete, such as Steel or other surfaces, please contact our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] to check suitability and surface preparation/application advice.

Application

• The mixed unit of Resin Technologies Food Safe Epoxy Kitchen Floor Paint must be applied immediately and with a consistent, thorough coating method
• Apply with a suitable roller, whilst a second pair of hands cuts in the edges of the space
• Flat areas should be cross-rolled ensuring an even and smooth finish throughout
• Move down the floor and repeat the process until complete
• If coating a large area, you may require multiple work-persons
• IF USING COARSE ANTI-SLIP paint will be aggregate free. Aggregate must be added manually, typically by scattering by hand it onto a still-wet first coat of Resin Technologies Food Safe Epoxy Kitchen Floor Paint and then back-rolling the paint
• A typical system would be 1 coat of relevant Primer and 2 coats of Resin Technologies Food Safe Epoxy Kitchen Floor Paint
• In this case after the primer has been applied, the first coat of Resin Technologies Food Safe Epoxy Kitchen Floor Paint should be applied no longer than 24 hours after the primer has cured or is dry to touch
• Similarly, the 2nd coat of Resin Technologies Food Safe Epoxy Kitchen Floor Paint should be applied no longer than 24 hours after the first coat of paint has cured
• Please note the pot life for this product is 20 minutes, the paint will be unworkable due to chemical curing after this time, ensure you remove the paint from the tin during this window
• The paint will be workable on your floor for 40 minutes
• For more information please see the Data Sheets in the 'Data Sheets' tab, or please contact our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]

Limitations

• Do not apply on New or Wet Concrete (under 28 days old with residual moisture content of or higher 6%)
• Do not apply below 7°C
• Temperatures below 20°C will negatively impact curing/drying times
• Do not expose to freezing conditions
• Do not expose to chemicals, wash or allow water to rest on surface until 7 days after application
• Do not expose to prolonged sunlight as this product is not UV Stable and will discolour
• Concrete is required to possess a Damp Proof Membrane beneath it in order for Epoxy Coatings to be applied

Health & Safety

• Wear appropriate PPE. I.E Gloves and protective safety goggles
• If in contact with skin wash off immediately with plenty of soap and water
• If discomfort occurs seek medical advice
• Always refer to the Material Safety Data Sheet before handling or mixing this product