- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
- High-performance epoxy coating which has been independently tested (ISO 22196) and given accreditation from Bio-master*, the UK’s leading provider of antimicrobial agents. This coating boasts an impressive kill rate for Covid-19 on surfaces making it a very practical and attractive option in sanitary environments.
- Two coats produce a tough, gloss finish. Typical uses include hospitals, dentist surgeries, doctors' surgeries, pharmaceutical industry and other hygiene control areas.
- High performance two-coat system.
- ≥70% Kill Rate for Covid 19.
- Available in 4 colours.
- Easy to clean durable surface.
- Antibacterial & Anti-microbial.
- 100% Solvent Free.
- Suitable for interior use - Surface Usable in 24 hours.
- For use on suitably prepared Concrete surfaces.
- Superb Coverage.
- *Please note: Bio-master test certificate is available upon request
Product customisation
Don't forget to save your customization to be able to add to cartResin Technologies Covid-19 Floor Paint produces a tough and gloss finish, and it has been independently tested (ISO 22196) and given accreditation from Bio-master*, the UKs leading provider of antimicrobial agents.
Resin Technologies Covid-19 Floor Paint is supplied in two pack sizes: 2.5kg and 5kg. Each unit is split between PART A and PART B. Weight measurements are for the whole unit.
*Please note: Bio-master test certificate is available upon request
Quick Links - Click To Jump To Section:
- Features & Benefits
- Typical Properties
- Curing
- Mixing
- Surface Preparation
- Application
- Limitations
- Health & Safety
Features & Benefits
- ≥70% Kill Rate for Covid 19
- Effective against Coronavirus
- Solvent Free
- Incredibly durable
- Easy to clean
Typical Properties
Technical Data | |
---|---|
Pot life @ 20°C: | 20 Minutes |
Working life | 40 Minutes |
Thickness | 250 Microns/Coat |
Consumption rate | 0.25-0.30kg/m² |
Coverage | Up to 4m²/kg |
Shelf life | 12 Months |
Minimum Temperature | 7°C |
Components | 2 Part System - Resin, Activator |
Recommended coats | Two coats |
Application tools | Brush, Roller |
Usage location | Interior |
Storage Temperature | 10 - 25 °C |
Curing
Cure Times | |
---|---|
Recoat Time @10°C: | 16-24 Hours |
Recoat Time @20°C: | 8-12 Hours |
Car Traffic Time @10°C: | 24-48 Hours |
Car Traffic Time @20°C: | 12-24 Hours |
Industrial Traffic Time @10°C: | 72 Hours |
Industrial Traffic Time @20°C: | 48 Hours |
Full Chemical Cure Time @20°C: | 7 Days |
Mixing
- Gently stir PART A for 2 minutes to ensure dispersal of pigment
- Once stirred, pour 100% contents of PART B into the PART A tin and thoroughly mix by mechanical means (a paddle on the end of a drill) for 90 seconds, or until a uniform colour and texture is achieved and the curing agent has fully dispersed
- Please note that after mixing both components, 100% of the material must be used in a single application and cannot be stored for later use as chemical curing will occur
Surface Preparation
- Ensure that the concrete is clean and free from dust, laitance oil etc
- Defective concrete should be made good using a repair mortar such as Resin Technologies All In One Repair Mortar
- A relevant Primer should be used such as Resin Technologies All Purpose Primer
- Suitable mechanical treatment, such as using a surface grinder, is the preferred treatment prior to application, as this ensures a mechanical “key” for the coating
- However, in instances where this is not feasible, acid etching can also be used for this purpose. Please see Resin Technologies Etch & Clean
Application
- The mixed unit must be applied immediately and with a consistent, thorough coating method
- Apply with a suitable roller, whilst a second pair of hands cuts in the edges of the space
- Flat areas should be cross-rolled ensuring an even and smooth finish throughout
- Move down the floor and repeat the process until complete
- If coating a large area, you may require multiple work-persons
- A typical system would be 1 coat of relevant Primer and 2 coats of Resin Technologies Covid-19 Floor Paint
- In this case after the primer has been applied, the first coat of Resin Technologies Covid-19 Floor Paint should be applied no longer than 24 hours after the primer has cured or is dry to touch
- Similarly, the 2nd coat of Resin Technologies Covid-19 Floor Paint should be applied no longer than 24 hours after the first coat of paint has cured
- Please note the pot life for this product is 20 minutes, the paint will be unworkable due to chemical curing after this time, ensure you remove the paint from the tin during this window
- The paint will be workable on your floor for 40 minutes
- For more information please see the Data Sheets in the 'Data Sheets' tab, or please contact our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Please see the relevant product Data Sheet in the 'Datasheets' Tab above.
Limitations
- Do not apply on New or Wet Concrete (under 28 days old with residual moisture content of or higher 6%)
- Do not apply below 7°C
- Temperatures below 20°C will negatively impact curing/drying times
- Do not expose to freezing conditions
- Do not expose to chemicals, wash or allow water to rest on surface until 7 days after application
- Do not expose to prolonged sunlight as this product is not UV Stable and will discolour
- Concrete is required to possess a Damp Proof Membrane beneath it in order for Epoxy Coatings to be applied
Health & Safety
- Wear appropriate PPE. I.E Gloves and protective safety goggles
- If in contact with skin wash off immediately with plenty of soap and water. If discomfort occurs seek medical advice
- This product should be applied strictly in accordance with manufacturer’s instructions
- Always refer to the Material Safety Data Sheet before handling or mixing this product
Please see the relevant product Data Sheet for the product to be used in the 'Datasheets' Tab above for specific details.
Data sheet
- Manufacturer
- Resin Technologies
- For Use By
- Consumer Use
- Interior / Exterior Use
- Interior Use
- For Use On
- Concrete
- Application Method
- Roller
Brush - Sheen
- Gloss
- Pack Size
- 2.5KG
5KG - Dry to Recoat (at 20°C)
- 8-12 Hours
- Pot Life (at 20°C)
- 20 minutes
- Coverage
- 4m² per kg
- Min. Application Temperature
- 7°C
- UN Number (Activator)
- N/A
- UN Number (Base)
- UN3082
- Dry for Light Traffic (at 20°C)
- 12-24 Hours
- Dry for Full Traffic (at 20°C)
- 48 Hours
- Colour(s)
- Standard Colours
- Base Type
- Solvent Free
- Suitable For Use On
- Concrete
- Suitable For Use On
- Floors
- Suitable For Use On
- Hospital Floors
- Finish
- Gloss
- Application Method
- Brush
- Application Method
- Roller
- Manufacturer
- Resin Technologies
- Components
- 2K
- Usages
- Floor Coatings
- Product Usage Type
- Topcoat
- Full Chemical Resistance
- 7 Days
- Colour Family
- Grey
- Colour Family
- Blue
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Resin Technologies Covid-19 Floor Paint is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Resin Technologies All Purpose Primer
A versatile, durable Epoxy primer for use on concrete floors and for most other substrates. Offering excellent adhesion, it forms a strong foundation for which subsequent coats can be applied. It can be used either as a single-coat which seals and protects against moisture or, alternatively, when two coats are applied this system can even act...
Resin Technologies Etch & Clean
The easy way to prepare a concrete floor or surface before beginning a paint or resurfacing project. Premier cleaning formula for preparing and cleaning concrete before applying epoxy paints or resurfacing products. The formula will change colour from a clear solution to a yellow colour to indicate neutralisation and allow you to maximise the...
Resin Technologies All In One Repair Mortar
A three-part heavy duty patch material for repairing concrete. With a finish harder than concrete itself and extreme long-life durability this product is ideal for almost any concrete patch or repair job, on roads, in pot holes or even in industrial workspaces. All In One Repair Mortar offers a concrete-like smooth finish in a natural...