- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
A versatile, durable Epoxy primer for use on concrete floors and for most other substrates. Offering excellent adhesion, it forms a strong foundation for which subsequent coats can be applied. It can be used either as a single-coat which seals and protects against moisture or, alternatively, when two coats are applied this system can even act as an effective damp proof membrane helping to prevent rising damp and other moisture contamination problems arising from concretes.
All Purpose Primer is grey in colour and designed for use as a base coat to seal most substrates. This product is general purpose and can be used in garages, warehouses and even environments with damp conditions.
- Easy To Mix and Apply
- 2 Part Epoxy System
- Solvent Free
- Excellent Adhesion and Sealing Qualities
- Superb Coverage (5m²/kg)
Resin Technologies All Purpose Primer is supplied in 2.5kg and 5kg pack sizes. Each unit is split between PART A and PART B. Weight measurements are for the whole unit.
Quick Links - Click To Jump To Section:
- Features & Benefits
- Typical Properties
- Mixing
- Surface Preparation
- Application
- Limitations
- Health & Safety
Features & Benefits
- Easy to use
- Excellent adhesion & sealing qualities
- Solvent free
Typical Properties
Technical Data | |
---|---|
Consumption Rate: | 0.2-0.3kg/m² |
Coverage: | Up to 5m²/kg |
Pot Life @20°C: | 20 minutes |
Components: | 2 Pack System. Resin + Activator |
Shelf Life: | 12 Months |
Application Tools: | Roller, Brush |
Usage Location: | Interior |
Storage Temperature: | 10 - 25 °C |
Touch Dry Time @20°C: | 8-12 Hours |
Recoat Time @20°C: | 12-24 Hours |
Traffic Time @20°C: | 24+ Hours |
Mixing
- Pour 100% contents of PART B into the PART A tin and thoroughly mix by mechanical means (a paddle on the end of a drill) for 90 seconds, or until a uniform colour is achieved
- Please note that after mixing both components, 100% of the material must be used in a single application and cannot be stored for later use
Surface Preparation
- Ensure a thorough cleaning of the surface which is to be primed
- Concrete should be free from dust and laitance through sanding or wire brushing
- Defective concrete should be made good using a repair mortar such as Resin Technologies All In One Repair Mortar
- Loose material of any kind should be removed via vacuum as and when appropriate
- For surfaces other than concrete please contact our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for advice
Application
- Once Mixed, apply immediately by Roller or Brush with a consistent method
- Floor areas should be cross rolled for even application and minimal marking
- If coating a large area utilise multiple work-persons
- Subsequent coats of primer or paint should be applied between 12-24 hours after the primer has cured and is touch dry
- Please note the pot life for this product is 20 minutes, the primer will be unworkable due to chemical curing after this time, ensure you remove the primer from the tin during this window
- For more information please see the Data Sheets in the 'Data Sheets' tab, or please contact our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Limitations
- Do not apply at temperatures below 7°C
- Do not expose to Freezing Conditions
- Temperatures below 20°C will negatively impact curing/drying times
- Do not expose to chemicals, wash or allow water to rest on surface until 7 days after application
Health & Safety
- Wear appropriate PPE. I.E Gloves and protective safety goggles
- If in contact with skin wash off immediately with plenty of soap and water. If discomfort occurs seek medical advice
- This product should be applied strictly in accordance with manufacturer’s instructions
- Always refer to the Material Safety Data Sheet before handling or mixing this product
Data sheet
- Manufacturer
- Resin Technologies
- For Use By
- Consumer Use
- Interior / Exterior Use
- Interior Use
- For Use On
- Concrete
- Application Method
- Roller
Brush - Sheen
- N/A
- Pack Size
- 2.5KG
5KG - Dry to Recoat (at 20°C)
- 12-24 Hours
- Pot Life (at 20°C)
- 20 minutes
- Coverage
- 5m² per kg
- Min. Application Temperature
- 7°C
- UN Number (Activator)
- N/A
- UN Number (Base)
- UN3082
- Dry for Light Traffic (at 20°C)
- After 24 Hours
- Colour(s)
- Standard Colours
- Base Type
- Solvent Free
- Suitable For Use On
- Concrete
- Suitable For Use On
- Concrete Floors
- Suitable For Use On
- Garage Floors
- Suitable For Use On
- Warehouse Floors
- Application Method
- Roller
- Manufacturer
- Resin Technologies
- Components
- 2K
- Usages
- Floor Coatings
- Product Usage Type
- Primer
- Full Chemical Resistance
- 7 Days
- Colour Family
- Grey
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Resin Technologies All Purpose Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT