- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
2-component epoxy polyamide primer containing zinc phosphate. A versatile epoxy primer with excellent resistance to salts, water and alkalies, with very good resistance to mild acids and solvents.
Please note: This item is Made To Order subject to a MOQ of 5 units and an extended lead time of 10 working days
- Replaces Nullifire PM021 General Purpose Epoxy Primer
- Excellent corrosion resistance
- Cured film is tough and abrasion resistant
- Used 40% diluted as a tie-coat over zinc silicate and metallized steel
- Excellent adhesion to aluminium
- Widely used within petrochemical, offshore and shipping industries
- Flat finish
Nullifire have made the decision in March 2023 to rebrand Nullifire PM021 General Purpose Epoxy Primer as Carboline Carboguard E 19 – please see a letter explaining the changes HERE.
Carboline Carboguard E 19 Primer is a two-component epoxy polyamide primer containing zinc phosphate. A versatile epoxy primer with excellent resistance to salts, water and alkalies, with very good resistance to mild acids and solvents.
Click To Jump To Section:
- Features and Benefits
- Product Specification
- Drying Times
- Surface Preparation
- Application Methods
- Application Conditions
- Health and Safety
Features and Benefits
- Excellent corrosion resistance
- Cured film is tough and abrasion resistant
- Used 40% diluted as a tie-coat over zinc silicate and metallized steel
- Excellent adhesion to aluminium
- Widely used within petrochemical, offshore and shipping industries
- Flat finish
Product Specification
Technical Data | ||||||
---|---|---|---|---|---|---|
Carboline Carboguard E 19 Primer | ||||||
Volume Solids: | 50 ± 2% | |||||
Theoretical Coverage Rate: | 5,0 m²/l at 100 µm | |||||
Allow for loss in mixing and application. | ||||||
Dry Film Thickness: | 30 - 200 microns (1.18 - 7.87 mils) per coat | |||||
Normally 75 µm | ||||||
Wet Film Thickness: | 60 – 400 µm per coat, normally 150 µm | |||||
Dry Temperature Resistance: | Continuous: 120°C (248°F) | |||||
Non-Continuous: 150°C (302°F) | ||||||
Primer: | Self-priming | |||||
Topcoats: | May be topcoated with epoxy, vinyl, polyurethane or other coatings as recommended by Rawlins on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected] | |||||
Limitations: | Not recommended for immersion service in strong acids or exposures in areas where chalking is undesirable. | |||||
Shelf Life: | Part A: 24 months at 24°C | |||||
Part B: 36 months at 24°C | ||||||
Storage Temperature and Humidity: | 5°C - 45°C | |||||
0 - 95% relative humidity |
Drying Times
Curing Schedule | ||||||
---|---|---|---|---|---|---|
Surface Temp. | Dry to Touch | Dry to Recoat | Final Cure | |||
5°C (41°F) | 4 Hours | 20 Hours | 21 Days | |||
15°C (59°F) | 2 Hours | 15 Hours | 14 Days | |||
25°C (77°F) | 1 Hour | 5 Hours | 10 Days |
- These times are based on 75 µm DFT. Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment and premature failure.
Surface Preparation
General
- Surface must be clean and dry.
- Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating.
Steel
- Abrasive blasting to min. Sa 2½ (ISO 8501-1)
- Alternatively, ultra high pressure water jetting to Nace No. 7 min. C Vis WJ-2. Max flash rust; C Vis WJ-2M.
Concrete
- Concrete must be cured at least 28 days at 24°C and 50% relative humidity or equivalent.
- Prepare surfaces in accordance with ASTM D42582 Surface Cleaning of Concrete and ASTM D4259 Abrading Concrete.
- Voids in concrete may require surfacing
Application Methods
Product Information | |||||
---|---|---|---|---|---|
Mixing: | Power mix separately, then combine and power mix. DO NOT MIX PARTIAL KITS. | ||||
Thinning: | May be thinned up to 40% with Carboline Thinner 15 | ||||
Ratio: | 2 : 1 (A to B) by volume | ||||
Pot Life: | 6 hours at 23°C and higher at lower temperatures | ||||
Airless Spray: | Pump Ratio: 30:1 (min) | ||||
GPM Output: 3.0 (min) | |||||
Material Hose: 3/8” (0.38 cm) I.D. (min) | |||||
Tip Size: 015-.021” | |||||
Output PSI: 2000 | |||||
Filter Size: 60 mesh | |||||
Brush and Roller (General): | For small areas and stripe coating. Multiple coats may be required to obtain desired appearance, and recommended dry film thickness. | ||||
Brush: | Use a medium bristle brush | ||||
Roller: | Use 3/8” nap solvent resistant core roller |
Application Conditions
Product Conditions | |||||
---|---|---|---|---|---|
Condition | Material | Surface | Ambient | Humidity | |
Minimum | 5°C (41°F) | 5°C (41°F) | 5°C (41°F) | 0% | |
Maximum | 40°C (104°F) | 50°C (122°F) | 50°C (122°F) | 85% |
- Industry standards are for substrate temperatures to be 3°C above the dew point.
- Condensation due to substrate temperatures below the dew point can cause flash rusting on prepared steel and interfere with proper adhesion to the substrate.
- Special application techniques may be required above or below normal application conditions.
Health and Safety
Clean Up
- Use Thinner 2 or Acetone
- In case of spillage, absorb and dispose of in accordance with local applicable regulations.
Safety
- Read and follow all caution statements on this product data sheet and on the SDS for this product.
- Employ normal workmanlike safety precautions.
- Hypersensitive persons should wear protective clothing, gloves and use protective cream on face, hands, and all exposed areas.
Ventilation
- When used as a tank lining or in enclosed areas, thorough air circulation must be used during and after application until the coating is cured.
- The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used.
Caution
- This product contains flammable solvents
- Keep away from sparks and open flames
- All electrical equipment and installations should be made and grounded in accordance with applicable regulations.
- In areas where explosion hazards exist, workmen should be required to use nonferrous tools and wear conductive and non-sparking shoes.
- Refer to the product and safety data sheet in the attachments section above for further details.
Data sheet
- Manufacturer
- Carboline Carboguard E 19 Primer
- Water / Solvent Based
- Solvent
- For Use On
- Steel, Concrete
- Application Method
- Airless Spray, Brush, Roller
- Sheen
- Flat
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 5L
- Mixing Ratio
- 2 : 1 (A to B) by volume
- Coverage
- 5,0 m²/l at 100 µm
- Compatible Topcoats
- May be topcoated with epoxy, vinyl, polyurethane or other coatings as recommended by Rawlins
- Max. Application Temperature
- Material: 40°C (104°F) - Surface: 50°C (122°F) - Ambient: 50°C (122°F) - Humidity: 0%
- Min. Application Temperature
- Material: 5°C (41°F) - Surface: 5°C (41°F) - Ambient: 5°C (41°F) - Humidity: 0%
- Solids by Volume
- 50 ± 2%
- Shelf Life (from date of manufacture)
- Part A: 24 months at 24°C - Part B: 36 months at 24°C
- Touch Dry
- 1 Hour @ 25°C (77°F)
- Recommended Dry Film Thickness
- 30 - 200 microns (1.18 - 7.87 mils) per coat
- Recommended Wet Film Thickness
- 60 – 400 µm per coat, normally 150 µm
- UN Number
- UN1263
- Dry to Recoat
- 5 Hours @ 25°C (77°F)
- Fully Cured
- 10 Days @ 25°C (77°F)
- Base Type
- Epoxy
- Suitable For Use On
- Aluminium
- Suitable For Use On
- Steel
- Suitable For Use On
- Zinc Silicate
- Finish
- Flat
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Spray
- Product Usage Type
- Primer
- Colour Family
- Red
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Nullifire PM021 General-Purpose Epoxy Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Carboline Thinner 15
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.
Carboline Thinner 2
Carboline Thinner 2 is a thinner for use in industrial coatings.
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...