- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Moisture tolerant epoxy resin primer for adhesion to damp substrates before application of RonaScreed self smoothing cementitious screeds, for excellent adhesion and minimal pin holing from porous substrates.
- Good adhesion to shot/ grit blasted steel
- Use before bonding of Ronafix screeds to steel substrates, such as stair pans
- Moisture tolerant, can be applied to surface damp concrete and screeds
- Use before application of RonaDeck Resin Bonded Surfacing to porous or surface damp concrete
- Easy to apply - solvent free; low odour
RonaFloor Epoxy Primer MT is a two pack solvent free primer for application to surface damp or porous concrete and screeded substrates. Typically used to prime concrete before application of RonaScreed self smoothing cementitious screeds, for excellent adhesion and minimal pin holing from porous substrates.
May be applied to shot/ grit blasted steel before application of Ronafix polymer modified screeds to stair pans and other applications where deflection of steel is minimal.
Quick Links - Click To Jump To Section:
Features & Benefits
- Two pack primer
- Use before application of RonaScreed self smoothing screed for reduced pin-holing and superior adhesion
- Good adhesion to shot/ grit blasted steel
- Use before bonding of Ronafix screeds to steel substrates, such as stair pans
- Moisture tolerant, can be applied to surface damp concrete and screeds
- Use before application of RonaDeck Resin Bonded Surfacing to porous or surface damp concrete
- Easy to apply
- Solvent free and low odour
- 30 minutes pot life
- Can be overcoated after 24 hours with flooring
Substrate Preparation
To achieve optimal adhesion it is essential that RonaFloor Epoxy Primer MT is applied to structurally sound, clean and touch dry substrates.
Surfaces must be prepared after making good any defects in the floor, ensuring that friable materials are removed and replaced (for fast cure repairs refer to RonaFloor Repair 1 Hour data sheets).
Concrete must be prepared by captive shot blasting or similar method to produce lightly textured, laitance free surfaces. Steel must be shot/ grit blasted to SA 2.5.
Substrates must be cleaned to remove grease, oil and dirt. Substrates must be allowed to dry after washing. Substrates must be vacuum cleaned, to remove shot and other loose materials.
Application Conditions
The workability and application characteristics of RonaFloor Epoxy Primer MT are adversely affected by low temperature; viscosity and curing time will increase. Therefore the material should ideally be stored, mixed and applied at 15°C to 20°C.
At lower application temperatures the material should be stored at or warmed to 15°C to 20°C prior to use. Application characteristics are severely affected below 10°C, minimum application temperature is 5°C.
Mixing
Add the full contents of the B component to the full contents of the A component and mix with a slow speed drill and spiral mixing paddle (MR3 type) for approximately 3-4 minutes.
Transfer to a shallow paint tray immediately after mixing, or pour onto the floor, to control exothermic reaction and extend working time. Material must never be taken directly from the mixing vessel, to avoid the risk of unmixed material being used.
Application
- Apply RonaFloor Epoxy Primer MT by short or medium nap lambswool or mohair roller at the stated coverage
- Broadcast 0.8-1.7mm kiln-dried sand or similar to refusal into the wet resin, a finer grade may be required for vertical application or for coatings
- Allow to cure for approximately 24 hours at 20°C
- Vacuum excess sand and protect until the screed or coating is applied
Cleaning
Clean tools immediately with xylene based solvent or RonaDeck Low VOC Cleaner.
Data sheet
- Manufacturer
- Ronacrete
- For Use By
- Professional Use
- Interior / Exterior Use
- Interior Use
- For Use On
- Concrete Floor Screeds
- Application Method
- Roller
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 4.8kg
- Mixing Ratio
- 1:1
- Pot Life (at 20°C)
- 30 minutes
- Coverage
- 3.5-4.5m²/kg/coat
- Max. Application Temperature
- 20°C
- Min. Application Temperature
- 5°C
- Colour(s)
- Clear
- Suitable For Use On
- Concrete Floor Screeds
- Application Method
- Roller
- Manufacturer
- Ronacrete
- Usages
- Moisture Tolerant
- Product Usage Type
- Primer
- Product Range
- RonaFloor
- Cleaning
- RonaDeck Low VOC Cleaner
- Bond Strength
- To Concrete:
Dry: 4.0N/mm²
Wet: 1.5N/mm² - Colour Family
- Clear
- Dry for Overcoating (20°C)
- Apply flooring after 24 hours
- Intercoat Period
- 24 hours at 20°C
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Ronacrete RonaFloor Epoxy Primer MT is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT