Follow us on:

Carboline Rustbond NG FC | Metal Primer & Sealer

Carboline Rustbond NG FC

109FNG
CAR10637

Carboline Rustbond NG FC is a cross-linked penetrating primer/sealer with good wetting properties. It is highly flexible and accepts a variety of topcoats. Recommended use as primer/sealers for marginally prepared steel and over old coatings. Its excellent wetting properties allows it to penetrate rust and discontinuities in existing coatings and provide a firm anchorage for a variety of topcoats.

  • Universal primer and tie-coat
  • Cures down to 2°C (36°F)
  • Excellent adhesion to SSPC-SP 2 prepared steel, galvanizing, aluminium, stainless steel
  • Highly flexible film
  • High solids
  • Low odour
  • Contains corrosion inhibitors
  • Compatible with a variety of topcoats
  • User friendly brush and roller application
  • Please note: This product is subject to a lead time of approximately 2-3 weeks

Please note: Colours shown are for illustrative purposes only

Colour
Size
Finish
£102.38(incl. VAT)
£85.32(ex. VAT)
Quantity
Please choose your colour
This Combination may be Subject to Extended Lead Times

No queries yet, leave the first!
Description

Click To Jump To Section:




Features and Benefits


  • 2 Pack Polymeric Epoxy Amine
  • Cross-linked penetrating primer/sealer with good wetting properties
  • Cures down to 2°C
  • Excellent wetting properties allows it to penetrate rust and discontinuities in existing coatings
  • Translucent yellow - Gloss finish
  • May be applied over most generic types of coatings.



Product Specification


Technical Data
Carboline Rustbond NG FC
Primer: Self-priming. May be applied over most generic types of coatings
Topcoats: Acrylics, alkyds, epoxies, polyurethanes
Finish: Gloss Chalks rapidly in sunlight
Solids Content: By Volume 90% +/- 1%
Theoretical Coverage Rate:

35.4 m²/l at 25 microns

17.7 m²/l at 50 microns

Allow for loss in mixing and application.

Dry Film Thickness: 25 - 51 microns per coat
Dry Temp. Resistance:

Continuous: 79°C

Non-Continuous: 93°C

Discoloration and loss of gloss is observed above 80°C

VOC Values:

As Supplied: 108 g

Thinner 2: 7% 150 g/l

Thinner 76: 7% 150 g/l

These are nominal values

Limitations:

Epoxies lose gloss, discolour, and chalk in sunlight exposure

Do not use for immersion service

Rustbond sealers must be topcoated

Shelf Life:

Part A & Part B: Min. 24 months at 24°C (75°F)

Shelf Life: (actual stated shelf life) when kept at recommended storage conditions and in original unopened containers.



Drying Times


Curing Schedule
Surface Temp Dry to Handle Dry to Topcoat Final Cure General
5°C 7 Days 5 Days 14 Days
10°C 48 Hours 48 Hours 9 Days
24°C 18 Hours 14 Hours 7 Days
32°C 14 Hours 5 Hours 2 Days



  • These times are based on 50% relative humidity and 25-50 microns dry film thickness
  • Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment and premature failure
  • Excessive humidity or condensation on the surface during curing can interfere with the cure, can cause discolouration, and may result in a surface haze. Any haze or blush must be removed by water washing before recoating
  • During high humidity conditions, it is recommended that the application be done while temperatures are increasing



Curing Schedule
Surface Temp Maximum Recoat Time Acrylics and Alkyds Maximum Recoat Time Epoxies and Urethanes
2°C 7 Days 21 Days
10°C 7 Days 21 Days
24°C 7 Days 21 Days
30°C 7 Days 14 Days



Surface Preparation


Preparation
General: Surfaces must be clean and dry. Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating
Steel: SSPC-SP2 or SP3
Previously Painted Surfaces: A test patch is recommended to verify compatibility with existing coating. Existing paint must attain a minimum 3A-3B rating in accordance with ASTM D3359 adhesion test



Application Methods


Product Information
Mixing:

Power mix components separately to break down any gel. Keep the mixing blade at slow speed and submerged in the product to minimize whipping of air into the material. Scrape the sides of the container occasionally to ensure uniformity. Continue to mix for 1-2 minutes

DO NOT MIX PARTIAL KITS

Thinning: Thinning not normally required but may be thinned up to 7% with Thinner 76 or Thinner 2. Use of thinners other than those supplied or recommended by Carboline may adversely affect product performance and void product warranty, whether express or implied
Ratio:

5L Kit

  • Part A: 2.5L
  • Part B: 2.5L
Pot Life:

For 2L sample:

  • 2 hours at 30°C
  • 4 hours at 25°C
  • 7 hours at 7°C
  • Pot life ends when material begins to thicken and exotherm



Application Conditions


Conditions
Condition Material Surface Ambient Humidity
Minimum 4°C 2°C 2°C 0%
Maximum 30°C 45°C 38°C 90%



  • This product simply requires the substrate temperature to be 3°C above the dew point
  • Condensation due to substrate temperatures below the dew point can cause flash rusting on prepared steel and interfere with proper adhesion to the substrate
  • Special application techniques may be required above or below normal application conditions



Health and Safety


Clean Up

  • Use Thinner 2
  • In case of spillage, absorb and dispose of in accordance with local applicable regulations

Safety

  • Read and follow all caution statements on this product data sheet and on the safety data sheet for this product
  • Employ normal workmanlike safety precautions

Ventilation

  • When used in enclosed areas, thorough air circulation must be used during and after application until the coating is cured
  • The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used
  • User should test and monitor exposure levels to ensure all personnel are below guidelines
  • If not sure or if not able to monitor levels, use MSHA/NIOSH approved respirator

Caution

  • THIS PRODUCT EXOTHERMS AT THE END OF ITS POT LIFE
  • Any unused quantities will become hot (70°C). Immediately spread out on an appropriate surface or add sand or other suitable heat sink to the unused material to reduce the severity of exotherm
  • Take appropriate precautions against breathing fumes
  • This product contains flammable solvents
  • Keep away from sparks and open flames
  • All electrical equipment and installations should be made and grounded in accordance with regulations
  • In areas where explosion hazards exist, users should be required to use non-ferrous tools and wear conductive and non-sparking shoes
  • Refer to the product data sheet and safety data sheet in the attachments section above for further details
Product Details
10637-992477

Data sheet

Manufacturer
Carboline
For Use By
Industrial Use
For Use On
Steel
Aluminium
Application Method
Brush, Roller, Spray
Sheen
Gloss
Colour
Translucent Yellow
Single, Two or Three Pack
Two-Pack
Pack Size
5L
Coverage
35.4 m²/l at 25 microns, 17.7 m²/l at 50 microns
Recommended Thinner/Cleaner
Carboline Thinner 76, Thinner 2
Max. Application Temperature
Material: 30°C, Surface: 45°C, Ambient: 38°C, Humidity: 90%
Min. Application Temperature
Material: 4°C, Surface: 2°C, Ambient: 2°C, Humidity: 0%
Solids by Volume
90% +/- 1%
Heat Resistance (up-to)
Continuous: 79°C, Non-Continuous: 93°C
VOC
As Supplied: 110 g/l
Shelf Life (from date of manufacture)
Part A & B: Min. 24 months at 24°C
Dry for Topcoat (at +20°C)
24°C: 14 Hours, 32°C: 5 Hours
Recommended Dry Film Thickness
25 - 51 microns per coat
UN Number (Activator)
UN3082
UN Number (Base)
UN3469
Dry to Handle (at 10°C)
48 Hours
Fully Cured
2°C: 14 Days, 10°C: 9 Days, 24°C: 7 Days, 32°C: 2 Days
Colour(s)
Standard Colours
Suitable For Use On
Aluminium
Suitable For Use On
Steel
Finish
Gloss
Application Method
Roller
Application Method
Spray
Application Method
Brush
Manufacturer
Carboline
Usages
Metal Primers & Undercoats
Product Usage Type
Primer & Sealer
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

Carboline Rustbond NG FC is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like
Carboline Thinner 2 | Solvents & Thinners

Carboline Thinner 2

Carboline Thinner 2 is a thinner for use in industrial coatings.

Price £37.88 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery
Carboline Thinner 76 | Solvents & Thinners

Carboline Thinner 76

Carboline Thinner 76 thinner for use in industrial coatings.

Price £55.36 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery
Hand & Power Tool Surface Preparation Kits for Steel

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £25.93 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery