- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
HMG 1K DTM 10 Colour is a single pack high quality direct to metal, single coat finish achieving a 10% gloss level. 1K DTM is a compliant product offering good corrosion resistance and early moisture resistance.
- For professional use
- Low odour and recoat at any stage, ready for use
- Suitable for most clean and degreased metal surfaces such as skips, containers, street furniture, agricultural and construction vehicles and machinery
- Spray application - airless/air-assisted, pressure pot & compliant spray gun
- Coverage: 6m²/L
- Shelf life: 12 months
- PG6/23 11 compliant
- Manufactured under the auspices of an ISO 9001 management system
- Available in 5,000+ colours from RAL, NCS, and British Standard
Product customisation
Don't forget to save your customization to be able to add to cartDescription
Quick Links - Click To Jump To Section:
Surface Preparation
- Application and use should always conform with the codes of practice described in BS 6150 and BS 5493
- Ensure surfaces are clean, dry and free from grease, oils, dust and other contamination prior to application - high pressure wash to remove all loose debris and other contamination
- Check all existing coatings are well adhered with all loose and failed material removed back to firm with all edges
well feathered - Thoroughly clean and degrease using suitable HMG Prep Clean
- Apply by cloth and quickly remove using clean lint free cloth
- Repeat until surface is clean and free from all deposits (grease, oil, silicone)
- Replace cloths regularly to ensure that contamination is not re-applied to the surface
- Abrade with P80 – P180 if necessary
Important instructions before use:
- Read and follow Safety Data Sheet, Technical Data Sheet (see 'Data sheets' tab above) and label instructions
- Stir all paints thoroughly before use
- Always use the same batch number on the same job
- Check colour & sheen - HMG will not accept any discrepancies arising after use
- Filter the product immediately before use
- Reduce emissions and maintain quality by replacing tin lid after use
- Suitability over existing coating should be trialled in small area prior to full application
- Not suitable for coating over bitumen or chlorinated rubber coatings
- Substrate temperature should be 5⁰C or above for application and during cure, and a minimum of 3⁰C above the dew point
- Adequate dry air ventilation should be supplied during drying
- Thinning should only take place after material is thoroughly mixed
Application
- Suggested Thinner: HMG 2621
- Recoat/Overcoat: At any stage
Airless/Air assisted:
- Thinning: RFU
- Spray gun setup: 13-15 thou
- Number of coats: 1
Pressure Pot:
- Mixing ratio: RFU
- Spray gun setup: 2.0
- Number of coats: 1
Compliant Spray Gun:
- Mixing ratio: Base 1, thinner 10-20%
- Spray gun setup: 1.6 - 2.0
- Number of coats:1 - 2
Storage
- Store between 5°C - 25°C
- When not in use, cans must be kept sealed
Health & Safety
- Refer to Safety Data Sheet (see 'Data Sheets' tab above) and tin label prior to use
- Suitable respiratory equipment should be worn when spraying
- Contaminated rags, spray booth filters or other substrates should be segregated from other chemical waste, soaked with Water and disposed of in a non-combustible container with a tight fitting lid
Product Details
10829-1002678
Data sheet
- Manufacturer
- HMG
- For Use By
- Professional Use
- For Use By
- Industrial Use
- For Use On
- Suitably Prepared Metal
Containers
Portable Buildings
Skips
Agricultural Machinery
Construction Machinery
Street Furniture
Machinery - Application Method
- Compliant Spray Gun
Pressure Pot
Airless/Air Assisted - Sheen
- 10% Sheen
- Single, Two or Three Pack
- Single
- Pack Size
- 15L
- Touch Dry (at 20°C)
- 2 hours
- Coverage
- 6m²/L
- Recommended Thinner/Cleaner
- HMG 2621
- Solids by Volume
- 55%
- VOC
- 0.41Kg/L
- Shelf Life (from date of manufacture)
- 12 months
- Recommended Dry Film Thickness
- 100 microns
- Recommended Wet Film Thickness
- 150 microns
- UN Number
- UN1263
- Dry to Recoat
- At any time
- Hard Dry
- 24 hours
- Flashpoint
- 24°C
- Colour(s)
- Fully Tintable
- Base Type
- Solvent-Based
- Suitable For Use On
- Steel
- Suitable For Use On
- Suitably Prepared Metal
- Suitable For Use On
- Street Signs
- Suitable For Use On
- Machinery
- Suitable For Use On
- Agricultural Machinery
- Suitable For Use On
- Construction Machinery
- Suitable For Use On
- Skips
- Suitable For Use On
- Powder Coated Surfaces
- Suitable For Use On
- Containers
- Suitable For Use On
- Portable Buildings
- Finish
- 10% Sheen
- Application Method
- Spray
- Manufacturer
- HMG Paints LTD
- Usages
- Anti-Corrosive
- Product Usage Type
- Topcoat
- Product Range
- 1K DTM
- Colour Family
- Violet
- Colour Family
- Anthracite Grey
- Colour Family
- Cream
- Colour Family
- Beige
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Off-White
- Colour Family
- Magnolia
- Colour Family
- White
- Colour Family
- Neutral
- Environment
- Atmospheric
- Touch Dry/Dust Free (@ 20-25°C)
- 2 hours
- Product Attributes
- 1 coat
- Product Attributes
- Overcoatable
- Product Attributes
- Low Odour
- Resistance to
- Corrosion
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG 1K DTM 10 Colour is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
You might also like
HMG Thinner 2621
HMG Thinner 2621 is a thinner for use in various applications. For use with compatible HMG systems.
Price
£13.45
(incl. VAT)
In Stock and Available for Delivery
HMG 1K DTM 70 Colour
HMG 1K DTM 70 Colour is a single pack direct to metal compliant coating, giving good corrosion and early moisture resistance, ideal for application as a single coat primer finish for use on skips, containers, agricultural and construction vehicles and machinery. Professional use only Low Odour Recoat at any stage, ready for use Quick...
Price
£55.78
(incl. VAT)
In Stock and Available for Delivery
HMG 1K DTM 30 Colour
HMG 1K DTM 30 Colour is a single pack direct to metal compliant coating, giving good corrosion and early moisture resistance, ideal for application direct to metal as a single coat primer finish for use on skips, containers, agricultural and construction vehicles and machinery. Low Odour Improved performance at higher film weights...
Price
£53.14
(incl. VAT)
In Stock and Available for Delivery
HMG 1K DTM Gloss Colour
HMG 1K DTM Gloss Colour is a single pack direct to metal compliant coating, giving good corrosion and early moisture resistance, ideal for application direct to metal as a single coat primer finish. For professional use Low odour and recoat at any stage, ready for use Suitable for most clean and degreased metal surfaces such as skips,...
Price
£55.78
(incl. VAT)
In Stock and Available for Delivery