- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
1-component, quick drying, solvent-free, moisture curing polyurethane primer with very low emission of volatile organic compounds (VOC) for consolidating and waterproofing cementitious screeds.
- For professional use
- Consolidator for weak cementitious screeds
- Surface consolidation and dust-repelling treatment on cementitious, anhydrite and heated substrates
- Anti-dust treatment for cementitious and dry anhydrite screeds with a crumbly surface
- Waterproofing cementitious screeds with a residual humidity content higher than the level recommended for laying parquet
- Very low emission level of volatile organic compounds (EMICODE EC1 Plus)
- May also be used as a primer on:
- OSB chipboard panels
- Slab-paved surfaces
- Ceramic tiles and terraces
- Traces of old glue
- Does not contain solvents, is odourless and is not flammable
- Shelf life: 12 months
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
Quick Links - Click To Jump To Section:
Features & Benefits
- For professional use
- Eco Prim PU 1K Turbo is a one-component polyurethane primer which hardens due to the humidity present in the surrounding air and in the screed
- Characterised by its short set to light foot traffic period, it quickly loses tackiness, so that parquet may be laid after a very short time (after approximately 2 hours in normal conditions of temperature and humidity)
- Surface consolidation and dust-repelling treatment on cementitious, anhydrite and heated substrates
- Waterproofing cementitious screeds with a residual humidity content higher than the level recommended for laying parquet
- Waterproofing treatment before laying wooden flooring, to prevent a failure due to excessive residual humidity in the cementitious screed
- Anti-dust treatment for cementitious and dry anhydrite screeds with a crumbly surface
- Priming surfaces before bonding parquet with MAPEI resin-based reactive adhesives
- Because of the total absence of solvents and odour, Eco Prim PU 1K Turbo may also be used on sites which are located close to inhabited areas (such as flats, schools, offices, etc.)
- After application and rapid curing of the resin, the substrate treated with Eco Prim PU 1K Turbo becomes more consistent, harder and is resistant to abrasion
- Eco Prim PU 1K Turbo can be applied to substrates with moisture up to 6% CM; (measured with Carbide hygrometer - UNI 10329) or relative moisture up to 92% R.H., or up to 98% for 2 coats (measured with in situ probe test - ASTM F2170 - BS 8203)
- On screeds with heating up to a maximum of 3% CM or 50 % H.R.
- Consumption: 80-100 g/m² per coat - as a vapour barrier up to a maximum of 450 g/m²
- EMICODE: EC1 Plus - very low emission
Recommendations
- Do not dilute Eco Prim PU 1K Turbo with water or solvent
- Do not apply on wet surfaces or in the presence of rising damp
- If a smoothing and levelling compound has to be applied, or if the parquet is to be laid after more than 24 hours, apply Eco Prim PU 1K Turbo so that a thin layer remains on the surface
- Completely saturate this layer with Quartz 0.8 while the primer is still fresh
- The product is suitable for consolidating heated screeds and anhydrite substrates which cannot be waterproofed
- These kinds of substrates must be dry before applying the primer
- The laying of wooden flooring on substrates treated with Eco Prim PU 1K Turbo must be carried out using a reactive polyurethane adhesive, an epoxy-polyurethane adhesive or a sililated polymer-based adhesive
- Maximum residual humidity permitted:
- 6% CM (carbide hygrometer - UNI 10329)
- 92% R.H. for 1 coat or 98% for 2 coats (in situ probe test - ASTM F2170 - BS 8203)
Application
Preparation of the substrate:
- The screed must be clean and free of oil, wax and dirt
- Traditional screeds must be cured for at least 7-10 days per centimetre of thickness, while quick-drying or rapid-drying screeds must be cured according to the manufacturer’s instructions for each particular product
- Cracks and crazing must be opened and then sealed with Eporip and Eporip Turbo in order to remove any breaks or interruptions in the surface
- Once the screed is dry and cured, if there are any areas with surface bleeding or that are weak and detached from the screed, the surface must be mechanically abraded before applying
- Before applying, remove all dust and any loose material from the surface
- If used for consolidating purposes, make sure that the porosity of the surface is sufficient to allow Eco Prim PU 1K Turbo to penetrate
- If the screed is excessively smooth, the surface must be abraded in order to open the pores
Application of the product:
- Apply Eco Prim PU 1K Turbo with a roller or brush
- On porous substrates, a single coat of the product is usually enough to obtain a good waterproofing and consolidating effect
- On particularly porous substrates, or substrates in poor condition, a second layer should be applied when the first is suitable to light foot traffic (after approximately 30 minutes)
- If the substrate needs to be rectified with a cementitious smoothing and levelling compound, apply a coat of Eco Prim PU 1K Turbo
- Make sure a thin layer is left on the surface and, while it is still wet, broadcast it with Quartz 0.8 until completely saturated
- When Eco Prim PU 1K Turbo has completely hardened, the cementitious smoothing compound may be applied after removing all quartz which is not sufficiently bonded
- On particularly porous substrates with residual moisture above 5%, apply at least two coats
- As soon as the surface sets to foot traffic check whether a third coat is required
- If a third coat is applied broadcast the surface with Quartz 0.8
- If a levelling compound with a thickness higher than 10 mm or a traditional solid wood parquet should not be applied, as an alternative to sprinkling on quartz, bonding of the levelling compound may be improved by applying a coat of Eco Prim T Plus on the surface of Eco Prim PU 1K Turbo
- Eco Prim T Plus must be applied after at least 4 hours (or when dry to the touch) and not later than 24 hours from the application of Eco Prim PU 1K Turbo
- If the parquet is to be laid directly after 24 hours, prepare the substrate with Quartz 0.8, as described above to provide a key for the cementitious smoothing and levelling compound
- As an alternative, it may be laid directly on the primer after at least 2 hours and after no more than 24 hours of its application using a reactive polyurethane adhesive, an epoxypolyurethane adhesive or a sililated-based adhesive
Cleaning
- Eco Prim PU 1K Turbo may be removed from clothing and tools while still fresh using Thinner PU or Cleaner L
- Once set, it may only be removed using a solvent cleaner
Storage & Safety Instructions
- Eco Prim PU 1K Turbo is stored for 12 months in its original, well-sealed container stored under normal conditions
- Protect from frost
- Instructions for the safe use of the product can be found on the latest version of the Safety Data Sheet (see 'Data Sheets' section above)
Data sheet
- Manufacturer
- Mapei
- For Use By
- Professional Use
- For Use On
- Cementitious Floors
Wooden Floors
Parquet
OSB
Paving
Ceramic Tiles
Old Adhesive - Application Method
- Brush
Roller - Single, Two or Three Pack
- Single
- Pack Size
- 10Kg
- Max. Application Temperature
- 35°C
- Min. Application Temperature
- 5°C
- Density
- 1.2g/cm³
- Solids by Volume
- 100%
- Waiting time
- Minimum 40 mins
- Base Type
- Solvent-Free
- Suitable For Use On
- Paving
- Suitable For Use On
- Cementitious Floors
- Suitable For Use On
- Old Adhesive
- Suitable For Use On
- Wooden Floors
- Suitable For Use On
- Ceramic Tile
- Suitable For Use On
- Parquet
- Suitable For Use On
- OSB
- Application Method
- Brush
- Application Method
- Roller
- Manufacturer
- Mapei
- Product Usage Type
- Primer
- Product Range
- Eco Prim
- Foot Traffic
- 30 - 40 minutes
- Hardening
- 2 hours
- Colour Family
- Brown
- Viscosity Brookfield (cP)
- At +23°C (mPa·s): 300 (rotor 1 - 10 rpm)
- Product Type
- Polyurethane
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Mapei Eco Prim PU 1K Turbo is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT